Recent Advances in Interface Modification of Cu/graphite Composites and Layered Ternary Carbides of Modified Layer Candidate

We review the fundamental properties and significant issues related to Cu/graphite composites.In particular,recent research on the interfacial modification of Cu/graphite composites is addressed,including the metal-modified layer,carbide-modified layer,and combined modified layer.Additionally,we propose the use of ternary layered carbide as an interface modification layer for Cu/graphite composites.

Effect of Ni-coated MoS2 on microstructure and tribological properties of(Cu−10Sn)-based composites

The(Cu−10Sn)−Ni−MoS2 composites,prepared by powder metallurgy,were studied for the effects of Ni-coated MoS2 on the microstructure,mechanical properties and lubricating properties.The mechanism of effects of Ni and MoS2 on the properties of composites was analyzed through a comparative experiment by adding Ni and MoS2 separately.The results show that the nickel wrapping around the MoS2 particles decreases the reaction rate of MoS2 with the copper matrix,and greatly improves the bonding of the matrix.The composites with 12 wt.%Ni-coated MoS2(C12)show the optimum performance including the mechanical properties and tribological behaviors.Under oil lubrication conditions,the friction coefficient is 0.0075 with a pressure of 8 MPa and a linear velocity of 0.25 m/s.The average dry friction coefficient,sliding against 40Cr steel disc,is measured to be 0.1769 when the linear velocity and pressure are 0.25 m/s and 4 MPa,respectively.

Microstructure and property of sub-micro WC-10 %Co particulate reinforced Cu matrix composites prepared by selective laser sintering

The WC-10%Co particulate reinforced Cu matrix composite material with a WC-Co∶Cu mass ratio of 20∶80 was successfully fabricated by selective laser sintering(SLS) process. The following optimal processing parameters were used: laser power of 700 W, scan speed of 0.06 m/s, scan line spacing of 0.15 mm, and powder layer thickness of 0.3 mm. The microstructure, composition, and phase of the laser processed material were investigated by scanning electron microscopy(SEM), X-ray diffraction(XRD), and energy dispersive X-ray(EDX) spectroscopy. The results show that the bonding mechanism of this process is liquid phase sintering. The Cu and Co act as the binder phase, while the WC acts as the reinforcing phase. The non-equilibrium effects induced by laser melting, such as high degrees of undercooling and high solidification rate, result in the formation of a metastable phase CoC0.25. The WC reinforcing particulates typically have three kinds of morphology. They are agglomerated and undissolved, incompletely separated and partially dissolved, separated and dissolved, which indicates that particle rearrangement acts as the dominant sintering mechanism for the larger WC, while dissolution-precipitation prevails for the smaller WC particles. Microhardness tester was used to determine the Vickers hardness across the cross-section of the laser sintered sample, with the average value being HV0.1268.5. However, the hardness varied considerably, which might be attributed to the WC segregation and the high solidification rate experienced by the molten pool.

Effect of alloying elements on mechanical properties in Cu-15%Cr in-situ composites

The effects of alloying elements on the mechanical properties as well as electrical conductivity in Cu-15%Cr(mass fraction) in-situ composites were systematically studied and high strength and high electrical conductive Cu base in-situ composites have been developed. The best combination is the addition of 0.1% to 0.2% Zr, Ti, or Sn in Cu-15%Cr in-situ composite, thermomechanical treatment to refine the microstructure and optimizing the precipitation of second phase. The strength is controlled by high density of dislocations in the Cu matrix, the lamellar spacing of the second phase, and the fine Cr precipitates. The aging treatment to reduce solute atoms has a beneficial effect on the increase of electrical conductivity. The addition of Zr, or Ti of about 0.15% to 0.2% promotes the precipitation of Cr particles.

Microstructure Evolution and Thermal Stability of Cu-15Cr in-situ Composites

The Cu-15Cr in-situ fiber-reinforced composites sheets were prepared by cold drawing combined with cold rolling process. The evolution process of Cr fibers was studied, and when cold rolling reduction ε = 95%, the morphology of Cr fiber at different annealing temperature and the thermal stability of Cu-15Cr alloy were studied. Microstructure was also studied by scanning electron microscopy（SEM）. Meanwhile, the tensile strength of the alloy was tested by means of a precision universal tester, and the resistance value of the alloy was determined by using a digital micro-Euclidean instrument. The experimental results show that, with the increase of deformation, Cr dendrites evolve into homogeneous and parallelly arranged Cr fibers, and the cross-section of Cr fibers undergoes a ＂V＂ shape transition to ＂一＂ shape. In addition, spheroidization of the Cr fibers occurs on edges and extends to the center as annealing temperature rises. Moreover, the Cr fibers remains stable when the annealing temperature is below 550 ℃. Furthermore, the tensile strength of Cu-15Cr alloy decreases gradually as the annealing temperature increases, while the electrical conductivity maximizes when annealing at 550 ℃. Our study also shows that Cu-15Cr alloy has obtained a better comprehensive performance with tensile strength of 656 MPa and electrical conductivity of 82%IACS after annealing at 450 ℃.

An investigation on mechanical properties of (Al_(63)Cu_(25)Fe_(12))p/ZL101 composites by squeeze casting

Influence of different extrusion pressures and pouring temperatures on comprehensive performance of(Al63Cu25Fe12)p/ZL101 composites is studied in this paper.The results show that the tensile strength,elongation and hardness of(Al63Cu25Fe12)p/ZL101 composite increase with the squeezing pressure increasing from 50 MPa to 100 MPa,and gradually reduce from 100 MPa to 150 MPa.In addition,the mechanical properties of the composite can be improved with pouring temperature growing,while the temperature should not exceed 760℃.When squeezing pressure is 100 MPa and pouring temperature is 720℃,mechanical properties of composites are the best.Finally,the mechanical properties of(Al 63 Cu 25 Fe 12)p/ZL101 composite will be improved by suitable heat treatment technology

Morphology and Frictional Characteristics Under Electrical Currents of Al_2O_3/Cu Composites Prepared by Internal Oxidation

Two Al2O3/Cu composites containing 0.24 wt.% Al2O3 and 0.60 wt.% Al2O3 separately are prepared by internal oxidation. Effects of sliding speed and pressure on the frictional characteristics of the composites and copper against brass are investigated and compared. The changes in morphology of the sliding surface and subsurface are examined with scanning electron microscope （SEM） and energy dispersive X-ray spectrum （EDS）. The results show that the wear resistance of the Al2O3/Cu composites is superior to that of copper under the same conditions, Under a given electrical current, the wear rate of Al2O3/Cu composites decreases as the Al2O3-content increases, However, the wear rates of the Al2O3/Cu composites and copper increase as the sliding speed and pressure increase under dry sliding condition. The main wear mechanisms for Al2O3/Cu composites are of abrasion and adhesion; for copper, it is adhesion, although wear by oxidation and electrical erosion can also be observed as the speed and pressure rise.

Properties and microstructure of Cu/diamond composites prepared by spark plasma sintering method

Cu/diamond composites have been considered as the next generation of thermal management material for electronic packages and heat sinks applications. Cu/diamond composites with different volume fractions of diamond were successfully prepared by spark plasma sintering（SPS） method. The sintering temperatures and volume fractions（50%, 60% and 70%） of diamond were changed to investigate their effects on the relative density, homogeneity of the microstructure and thermal conductivity of the composites. The results show that the relative density, homogeneity of the microstructure and thermal conductivity of the composites increase with decreasing the diamond volume fraction; the relative density and thermal conductivity of the composites increase with increasing the sintering temperature. The thermal conductivity of the composites is a result of the combined effect of the volume fraction of diamond, the homogeneity and relative density of the composites.

Effects of rolling and annealing on microstructures and properties of Cu/Invar electronic packaging composites prepared by powder metallurgy

The Cu/Invar composites of 40% Cu were prepared by powder metallurgy, and the composites were rolled with 70% reduction and subsequently annealed at 750 ℃. Phases, microstructures and properties of the composites were then studied. After that, the amount of a-Fe（Ni,Co） in the composites is reduced, because a-Fe（Ni,Co） partly transfers into y-Fe（Ni,Co） through the diffusion of the Ni atoms into a-Fe（Ni,Co） from Cu. When the rolling reduction is less than 40%, the deformation of Cu takes place, resulting in the movement of the Invar particles and the seaming of the pores. When the rolling reduction is in the range from 40% to 60%, the deformations of Invar and Cu occur simultaneously to form a streamline structure. After rolling till 70% and subsequent annealing, the Cu/Invar composites have fine comprehensive properties with a relative density of 98.6%, a tensile strength of 360 MPa, an elongation rate of 50%, a thermal conductivity of 25.42 W/（m.K） （as-tested） and a CTE of 10.79× 10-6/K （20-100 ℃）.

放电等离子烧结Cu-15Ni-8Sn/石墨自润滑复合材料摩擦磨损性能研究

以Cu-15Ni-8Sn合金为基体,石墨为润滑剂,采用放电等离子烧结技术制备了Cu-15Ni-8Sn/石墨自润滑复合材料.使用扫描电子显微镜、X射线衍射仪和万能试验机研究了复合材料的微观组织、物相组成和室温力学性能,通过球-盘式摩擦试验机测试复合材料的摩擦磨损性能,利用三维轮廓仪测量材料磨损体积,借助扫描电子显微镜对磨痕形貌进行表征.结果表明:向Cu-15Ni-8Sn基体材料中添加石墨后,材料的硬度明显降低;随着石墨含量的提高,复合材料的抗压强度逐渐降低.当添加质量分数为3%的石墨时,Cu-15Ni-8Sn/石墨自润滑复合材料的耐磨性最好,磨损率最小为3.0×10^(-6)mm^(3)/(N·m),其磨损机理主要以磨粒磨损为主.

间断直流磁场对Al-5Mg-3Zn-1Cu合金凝固组织和性能的影响

对Al-5Mg-3Zn-1Cu合金的凝固过程施加不同直流电压(0~300 V)和放电频率(0~20 Hz)以及占空比为30%的间断直流磁场,研究了间断直流磁场对其凝固组织及力学性能的影响。结果表明:间断直流磁场有效细化了合金的凝固组织,初生α-Al相由无磁场时的粗大枝晶变为细小的蔷薇状晶粒,第二相由粗大而连续的网格状结构变为细小而断续分布结构。随着直流电压的增加,合金的晶粒尺寸、第二相体积分数和长度均减小,抗压强度和断裂应变均先升后降;随着放电频率的增加,晶粒尺寸、第二相体积分数和长度均先减小后增大,抗压强度和断裂应变均先升后降。施加间断直流磁场后,合金的拉伸性能提高,断口中的准解理面减少,撕裂棱增多。当直流电压为200 V、放电频率为5 Hz时,合金的抗压强度和断裂应变最大,与无磁场时相比分别提高了31.6%和43%,抗拉强度和断后伸长率则分别提高了79.71%和83.3%。

Mechanical properties of Cu based composites reinforced by carbon nanotubes

Cu based composites reinforced by 0%～25% (volume fraction) carbon nanotubes were prepared.The fracture behaviors and the rolling properties of the composites and the effects of the volume fraction of the carbon nanotubes were studied.The experimental results show that the fracture toughness of the composites is related to the pulling out and bridging of the carbon nanotubes in the fracture process.With the volume fraction of the carbon nanotubes increasing, the Vicker’s hardness and the compactness of the composites increase first and then decrease. The peaks of the hardness and the compactness occur at 12%～15% of volume fraction of carbon nanotubes.Some proper ratio of rolling reduction benefits to the comprehensive mechanical properties of the composites.

Effects of intermediate Ni layer on mechanical properties of Al–Cu layered composites fabricated through cold roll bonding

Layered composites have attracted considerable interest in the recent literature on metal composites. Their mechanical properties depend on the quality of the bonding provided by the intermediate layers. In this study, we analyzed the mechanical properties and bond strengths provided by the nickel layer with respect to its thickness and nature(either powder or coating). The results suggest that bond strength decreases with an increase in the content of nickel powder. At 0.3 vol% of nickel coating, we found the nature of nickel to be less efficient in terms of bond strength. A different picture arose when the content of nickel was increased and the bond strength increased in nickel coated samples. In addition, the results demonstrate that mechanical properties such as bend strength are strongly dependent on bond strength.

Self-propagating High-temperature Synthesis, Microstructure and Mechanical Properties of TiC-TiB_2-Cu Composites

TiC-TiB2-Cu composites were produced by self-propagating high-temperature synthesis combined with pseudo hot isostatic pressing using Ti, B4C and Cu powders. The microstructure and mechanical properties of the composites were investigated. The X-ray diffraction （XRD） and scanning electron microscopy （SEM） results showed that the final products were only TiC, TiB2 and Cu phases. The clubbed TiB2 grains and spheroidal or irregular TiC grains were found in the microstructure of synthesized products. The reaction temperature and grain size of TiB2 and TiC particles decreased with increasing Cu content. The introduction of Cu into the composites resulted in a drastic increase in the relative density and flexual strength, and the maximum values were obtained with the addition of 20 wt pct, while the fracture toughness was the best when Cu content was 40 wt pct.

Thermal expansion and mechanical properties of high reinforcement content SiC_(p)/Cu composites fabricated by squeeze casting technology

High reinforcement content SiCp/Cu composites (φp=50%, 55% and 60%) for electronic packaging applications were fabricated by patent cost-effective squeeze-casting technology. The composites appear to be free of pores, and the SiC particles are distribute uniformly in the composites. The mean linear coefficients of thermal expansion (CTEs, 20-100 ℃ ) of as-cast SiCp/Cu composites range from 8.8×10-6 ℃-1 to 9.9×10-6 ℃-1 and decrease with the increase of SiC content. The experimental CTEs of as-cast SiCp/Cu composites agree well with the predicted values based on Kerner model. The CTEs of composites reduce after annealing treatment due to the fact that the internal stress of the composite is released. The Brinell hardness increases from 272.3 to 313.2, and the modulus increases from 186 GPa to 210 GPa for the corresponding composites. The bending strength is larger than 374 MPa, but no obvious trend between bending strength and SiCp content is observed.

Reaction thermodynamics and kinetics on in situ Al_2O_3/Cu composites

The preferred internal oxidation of aluminum in Cu Al alloy was used to obtain in situ Al 2O 3/Cu composites. The reinforcement particles were mainly γ Al 2O 3, some θ Al 2O 3 and a little α Al 2O 3. Thermodynamics analyses show that the chemical reactions are 3Cu 2O+2Al=6Cu+Al 2O 3 or 3CuO+2Al=3Cu+Al 2O 3. A related equilibrium diagram was drawn. The experiments and investigation show that the formation rate of Al 2O 3 was controlled by the diffusion of oxygen in matrix.

Tribological behavior of CNTs-Cu and graphite-Cu composites with electric current

CNTs-Cu and graphite-Cu composites were separately prepared by powder metallurgy technique under the same consolidation processing. Tribological behavior of the composites with electric current was investigated by using a pin-on-disk friction and wear tester. The results show that the friction coefficient and wear rate of the composites decrease with increasing the reinforcement content, and increase with increasing the electric current density; the effects of electric current are more obvious on tribological properties of graphite-Cu composites than on CNTs-Cu composites; for graphite-Cu composites the dominant wear mechanisms are electric arc erosion and adhesive wear, while for CNTs-Cu composites are adhesive wear.

A Novel Technique for Preparation of Electrically Conductive ABS/Cu Polymeric Gradient Composites

A novel technique for preparing functionally gradient electrically conductive polymeric composites was developed by using of solution casting technique on the principle of Stokes＇ law. Acrylonitrile- butadiene-styrene/Cu （ABS/Cu） gradient polymeric composites were prepared successfully using this technique. The gradient structures, electrically conductive performance and mechanical properties of the ABS/Cu composites were investigated. Optical microscope observation shows that the gradient distribution of Cu particles in ABS matrix was formed along their thickness-direction. The electrically conductive testing results indicate that the order of magnitude of surface resistivity was kept in 10^15 Ω at ABS rich side, while that declined to 10^5 Ω at Cu particles rich side, and the percolation threshold was in the range of 2.82 vo1%- 4.74 vol% Cu content at Cu particles rich side. Mechanical test shows that the tensile strength reduced insignificantly as the content of Cu increases owing to the gradient distribution.

Monthly composites from Sentinel-1 and Sentinel-2 images for regional major crop mapping with Google Earth Engine

Rapid and accurate access to large-scale,high-resolution crop-type distribution maps is important for agricultural management and sustainable agricultural development.Due to the limitations of remote sensing image quality and data processing capabilities,large-scale crop classification is still challenging.This study aimed to map the distribution of crops in Heilongjiang Province using Google Earth Engine(GEE)and Sentinel-1 and Sentinel-2 images.We obtained Sentinel-1 and Sentinel-2 images from all the covered study areas in the critical period for crop growth in 2018(May to September),combined monthly composite images of reflectance bands,vegetation indices and polarization bands as input features,and then performed crop classification using a Random Forest(RF)classifier.The results show that the Sentinel-1 and Sentinel-2 monthly composite images combined with the RF classifier can accurately generate the crop distribution map of the study area,and the overall accuracy(OA)reached 89.75%.Through experiments,we also found that the classification performance using time-series images is significantly better than that using single-period images.Compared with the use of traditional bands only(i.e.,the visible and near-infrared bands),the addition of shortwave infrared bands can improve the accuracy of crop classification most significantly,followed by the addition of red-edge bands.Adding common vegetation indices and Sentinel-1 data to the crop classification improved the overall classification accuracy and the OA by 0.2 and 0.6%,respectively,compared to using only the Sentinel-2 reflectance bands.The analysis of timeliness revealed that when the July image is available,the increase in the accuracy of crop classification is the highest.When the Sentinel-1 and Sentinel-2 images for May,June,and July are available,an OA greater than 80%can be achieved.The results of this study are applicable to large-scale,high-resolution crop classification and provide key technologies for remote sensing-based crop classification in small-scale agricultural areas.

Process optimization,microstructures and mechanical/thermal properties of Cu/Invar bi-metal matrix composites fabricated by spark plasma sintering

An orthogonal experiment scheme was designed to investigate the effects of the Cu content,compaction pressure,and sintering temperature on the microstructures and mechanical and thermal properties of(30−50)wt.%Cu/Invar bi-metal matrix composites fabricated via spark plasma sintering(SPS).The results indicated that as the Cu content increased from 30 to 50 wt.%,a continuous Cu network gradually appeared,and the density,thermal conductivity(TC)and coefficient of thermal expansion of the composites noticeably increased,but the tensile strength decreased.The increase in the sintering temperature promoted the Cu/Invar interface diffusion,leading to a reduction in the TC but an enhancement in the tensile strength of the composites.The compaction pressure comprehensively affected the thermal properties of the composites.The 50wt.%Cu/Invar composite sintered at 700℃ and 60 MPa had the highest TC(90.7 W/(m·K)),which was significantly higher than the TCs obtained for most of the previously reported Cu/Invar composites.