Cu-30Ni-xRE(x=0–0.213 wt.%) alloy was prepared by adding rare earths(RE) in melted Cu-30Ni alloy using metal mould casting method.The effects of RE on corrosion resistance of the alloy in simulated seawater were inve...Cu-30Ni-xRE(x=0–0.213 wt.%) alloy was prepared by adding rare earths(RE) in melted Cu-30Ni alloy using metal mould casting method.The effects of RE on corrosion resistance of the alloy in simulated seawater were investigated using optical microscope,scanning electronic microscope with energy-dispersive spectrometer and electrochemical measurement system.The results showed that the corrosion resistance of Cu-30Ni alloy was greatly improved by adding proper amount of RE,whereas excess addition of RE worsened ...展开更多
Shot peening is a surface modification technology with the metal surface nano machine(SNC),which can modify the surface microstructure and extend the fatigue life of Cu-19Ni alloy.The hardness,damage evolution and mec...Shot peening is a surface modification technology with the metal surface nano machine(SNC),which can modify the surface microstructure and extend the fatigue life of Cu-19Ni alloy.The hardness,damage evolution and mechanical properties were investigated and characterized by scanning electron microscope(SEM),laser confocal microscope(LSM)and material surface performance tester(CFT).The results showed that the surface roughness and friction coefficient of Cu-19Ni alloy decreased with the increase of shot peening duration and diameter,while the microhardness and strength increased.Moreover,with the increase in shot peening duration and diameter,SEM observation showed that the fracture dimples became smaller,meanwhile,with the increase of small cleavage planes,shear tearing ridges and the thickness of the surface nano layer,the fracture mode gradually evolved from plastic to brittle fracture.The uniaxial tensile test of shot peened Cu-19Ni alloy was carried out by MTS testing machine combined with digital image correlation technology(DIC).The evolution of Cu-19Ni surface damage was analyzed,and the evolution equations describing the damage of large deformation zone and small deformation zone were established.The effect of shot peening on the damage evolution behavior of Cu-19Ni alloy was revealed.展开更多
After solutionized, 70Cu 30Ni alloy was deformed in different degrees and then exposed both in NaCl solution and in seawater. The results show that with the increase of deformation, the E c and R p -1 ...After solutionized, 70Cu 30Ni alloy was deformed in different degrees and then exposed both in NaCl solution and in seawater. The results show that with the increase of deformation, the E c and R p -1 of 70Cu 30Ni alloy decrease more quickly and fluctuate less when the exposure time increases, and the corrosion product films contain more nickel and less chloride because the distribution of dislocations tends to be homogeneous.展开更多
The microstrueture in shape memory alloy Cu—14Al—4Ni aged for two years at room temper- ature has been studied,and the substructure slow change has been observed.The domains of highly ordered phase and the transitio...The microstrueture in shape memory alloy Cu—14Al—4Ni aged for two years at room temper- ature has been studied,and the substructure slow change has been observed.The domains of highly ordered phase and the transition regions appear at grain boundaries,the twin bounda- ries damage.Furthermore,the microstructure also gives the appearance and growth of antiphase domains like rectangular network.The long period antiphuse boundary structures and the antiphase domains have bee.observed first at the single diffracted vector .The con- centration gradient of solute atom Al has heen found from the matrixes to the grain bounda- ries,the matrixe is poor in Al and the grain boundaries are rich in Al.展开更多
Some azoles were tested such as 3-amino-1,2,4-triazole (ATA), 3-4’-bitriazole -1,2,4 (BiTA)and 2-Mercaptobenzimidazole (MBI) against Cu-30Ni alloy corrosion in 3%NaCl polluted by ammonia using potentiodynamic measure...Some azoles were tested such as 3-amino-1,2,4-triazole (ATA), 3-4’-bitriazole -1,2,4 (BiTA)and 2-Mercaptobenzimidazole (MBI) against Cu-30Ni alloy corrosion in 3%NaCl polluted by ammonia using potentiodynamic measurements and electrochemical impedance spectroscopy and non-electrochemical techniques (scanning Electron Microscopy (SEM)) studied surface morphology has been used to characterize electrode surface. This study permitted to follow the evolution of the inhibitory effect of some azoles, on Cu-30Ni alloy corrosion in 3%NaCl polluted by ammonia and indicate that the tested inhibitors act as a good mixed-type inhibitor retarding the anodic and cathodic reactions. An increase of the inhibitors concentration leads to a decrease of corrosion rate and inhibition efficiency increase.展开更多
A new concept of undercooling heredity is developed to evaluate the undercooling ability in a non catalytic nucleation coated mould, where alloy melts were highly undercooled previously. Before the heredity experiment...A new concept of undercooling heredity is developed to evaluate the undercooling ability in a non catalytic nucleation coated mould, where alloy melts were highly undercooled previously. Before the heredity experiment a non catalytic nucleation composite glass lined coating (B F) was prepared on the inner surface of mould and the Cu 70 Ni 30 alloy was selected to perform undercooling experiment in the B F non catalytic coating mould. Its ratio of undercooling heredity was 0.76. The results prove that the B F coating is an ideal non catalytic media for purified Cu 70 Ni 30 alloy melts due to its small contact angle between the melt and coating layer. Considering that various microstructures form under different undercoolings, two critical undercoolings, Δ T 1 and Δ T 2, and their corresponding microstructures of Cu 70 Ni 30 alloy are well defined. Moreover, it is found that the manned trigging solidification in the non catalytic coating mould could be used to get directional undercooling dendrite structure while the melt undercooling is larger than the critical undercooling Δ T 2.展开更多
Experiments of X-ray diffraction for liquid Cu70Ni30 alloy above and below its liquidus (1 230℃) have been carried out. By the analysis of experimental results, it is discovered that difference between structures of ...Experiments of X-ray diffraction for liquid Cu70Ni30 alloy above and below its liquidus (1 230℃) have been carried out. By the analysis of experimental results, it is discovered that difference between structures of liquid and undercooled Cu70Ni30 alloy is their cluster sizes. The correlation radius of cluster is 1.125 nm and the atom number of cluster is 403 at 1 250-1 400℃, and they are 1.3 nm and 704 respectively at the undercooled liquid state (1 200℃). The structure of liquid alloy is fee short order and its solid structure, fcc, is kept from liquid fcc short order.展开更多
A molecular dynamics (MD) simulation study has been performed for the rapid solidification of Cu70Ni30 adopting the quantum Sutton-Chen many-body potentials. By analyzing the bond-types and the relation of atomic aver...A molecular dynamics (MD) simulation study has been performed for the rapid solidification of Cu70Ni30 adopting the quantum Sutton-Chen many-body potentials. By analyzing the bond-types and the relation of atomic average energy versus temperature, it was demonstrated that as cooling rate being 2 × 1012 K/s, the Cu70Ni30 formed fcc crystal structures and freezing point was found. In addition, having analyzed the transformation of microstructures and the detail of crystal growth by using atomic trace and visual method, not only could the formation of binary disordered solid solution be showed, but also the solidification of liquid metals and the crystal growth processes could be further understood.展开更多
Liquid structure of molten pure Cu, Cu-12Al, Cu-12Al-4Ni (mass fraction, %) alloys has been investigated using the X-ray diffraction method. It is found that the main peak of the structure factor of pure Cu is symmetr...Liquid structure of molten pure Cu, Cu-12Al, Cu-12Al-4Ni (mass fraction, %) alloys has been investigated using the X-ray diffraction method. It is found that the main peak of the structure factor of pure Cu is symmetrical. In the front of main peak, the curve takes on a shape of parabola, whereas a distinct pre-peak has been found around a scattering vector magnitude of 18.5 nm-1 in the structure factor of the liquid Cu-12Al alloy. This pre-peak increases its inten-sity with the addition of Ni in the liquid Cu-12Al-4Ni alloy. The appearance of a pre-peak is a mark of the mediate-range order. Based on Daken-Gurry theory and according to mu-tual interaction between unlike atoms, the analysis of corre-lation between different composition and liquid structure was done: the strong interaction exists between Cu and Ni, so Cu-Al can form strong chemical bond which causes compound-forming behavior. Therefore, the medium-range size clusters can form in melt. The presence of the pre-peak corresponds to these展开更多
基金Project Financially supported by Major State Basic Research Development Program of China (2007CB616903)
文摘Cu-30Ni-xRE(x=0–0.213 wt.%) alloy was prepared by adding rare earths(RE) in melted Cu-30Ni alloy using metal mould casting method.The effects of RE on corrosion resistance of the alloy in simulated seawater were investigated using optical microscope,scanning electronic microscope with energy-dispersive spectrometer and electrochemical measurement system.The results showed that the corrosion resistance of Cu-30Ni alloy was greatly improved by adding proper amount of RE,whereas excess addition of RE worsened ...
基金Funded by Natural Science Foundation of the Inner Mongolia(Nos.2019MS01015,2019MS01017)National Natural Science Foundation of China(No.11002065)。
文摘Shot peening is a surface modification technology with the metal surface nano machine(SNC),which can modify the surface microstructure and extend the fatigue life of Cu-19Ni alloy.The hardness,damage evolution and mechanical properties were investigated and characterized by scanning electron microscope(SEM),laser confocal microscope(LSM)and material surface performance tester(CFT).The results showed that the surface roughness and friction coefficient of Cu-19Ni alloy decreased with the increase of shot peening duration and diameter,while the microhardness and strength increased.Moreover,with the increase in shot peening duration and diameter,SEM observation showed that the fracture dimples became smaller,meanwhile,with the increase of small cleavage planes,shear tearing ridges and the thickness of the surface nano layer,the fracture mode gradually evolved from plastic to brittle fracture.The uniaxial tensile test of shot peened Cu-19Ni alloy was carried out by MTS testing machine combined with digital image correlation technology(DIC).The evolution of Cu-19Ni surface damage was analyzed,and the evolution equations describing the damage of large deformation zone and small deformation zone were established.The effect of shot peening on the damage evolution behavior of Cu-19Ni alloy was revealed.
基金Projects(YKJ201008,KXJ08135)supported by Scientific Research Startup Foundation for Introducing Talents of Nanjing Institute of Technology,ChinaProject(JHB2011-25)supported by the Industrialization of Scientific Research Promotion Projects of Colleges and Universities in Jiangsu Province,ChinaProject(CKJB201206)supported by Innovation Foundation of Nanjing Institute of Technology,China
文摘After solutionized, 70Cu 30Ni alloy was deformed in different degrees and then exposed both in NaCl solution and in seawater. The results show that with the increase of deformation, the E c and R p -1 of 70Cu 30Ni alloy decrease more quickly and fluctuate less when the exposure time increases, and the corrosion product films contain more nickel and less chloride because the distribution of dislocations tends to be homogeneous.
文摘The microstrueture in shape memory alloy Cu—14Al—4Ni aged for two years at room temper- ature has been studied,and the substructure slow change has been observed.The domains of highly ordered phase and the transition regions appear at grain boundaries,the twin bounda- ries damage.Furthermore,the microstructure also gives the appearance and growth of antiphase domains like rectangular network.The long period antiphuse boundary structures and the antiphase domains have bee.observed first at the single diffracted vector .The con- centration gradient of solute atom Al has heen found from the matrixes to the grain bounda- ries,the matrixe is poor in Al and the grain boundaries are rich in Al.
文摘Some azoles were tested such as 3-amino-1,2,4-triazole (ATA), 3-4’-bitriazole -1,2,4 (BiTA)and 2-Mercaptobenzimidazole (MBI) against Cu-30Ni alloy corrosion in 3%NaCl polluted by ammonia using potentiodynamic measurements and electrochemical impedance spectroscopy and non-electrochemical techniques (scanning Electron Microscopy (SEM)) studied surface morphology has been used to characterize electrode surface. This study permitted to follow the evolution of the inhibitory effect of some azoles, on Cu-30Ni alloy corrosion in 3%NaCl polluted by ammonia and indicate that the tested inhibitors act as a good mixed-type inhibitor retarding the anodic and cathodic reactions. An increase of the inhibitors concentration leads to a decrease of corrosion rate and inhibition efficiency increase.
文摘A new concept of undercooling heredity is developed to evaluate the undercooling ability in a non catalytic nucleation coated mould, where alloy melts were highly undercooled previously. Before the heredity experiment a non catalytic nucleation composite glass lined coating (B F) was prepared on the inner surface of mould and the Cu 70 Ni 30 alloy was selected to perform undercooling experiment in the B F non catalytic coating mould. Its ratio of undercooling heredity was 0.76. The results prove that the B F coating is an ideal non catalytic media for purified Cu 70 Ni 30 alloy melts due to its small contact angle between the melt and coating layer. Considering that various microstructures form under different undercoolings, two critical undercoolings, Δ T 1 and Δ T 2, and their corresponding microstructures of Cu 70 Ni 30 alloy are well defined. Moreover, it is found that the manned trigging solidification in the non catalytic coating mould could be used to get directional undercooling dendrite structure while the melt undercooling is larger than the critical undercooling Δ T 2.
文摘Experiments of X-ray diffraction for liquid Cu70Ni30 alloy above and below its liquidus (1 230℃) have been carried out. By the analysis of experimental results, it is discovered that difference between structures of liquid and undercooled Cu70Ni30 alloy is their cluster sizes. The correlation radius of cluster is 1.125 nm and the atom number of cluster is 403 at 1 250-1 400℃, and they are 1.3 nm and 704 respectively at the undercooled liquid state (1 200℃). The structure of liquid alloy is fee short order and its solid structure, fcc, is kept from liquid fcc short order.
基金supported by the National Natural Science Foundation of China(Grant No.50271026).
文摘A molecular dynamics (MD) simulation study has been performed for the rapid solidification of Cu70Ni30 adopting the quantum Sutton-Chen many-body potentials. By analyzing the bond-types and the relation of atomic average energy versus temperature, it was demonstrated that as cooling rate being 2 × 1012 K/s, the Cu70Ni30 formed fcc crystal structures and freezing point was found. In addition, having analyzed the transformation of microstructures and the detail of crystal growth by using atomic trace and visual method, not only could the formation of binary disordered solid solution be showed, but also the solidification of liquid metals and the crystal growth processes could be further understood.
基金This work was supported by the National Natural Science Foundation of China (Grant No. 50071028) the Natural Science Foundation of Shandong Province (Grant No. Z99F01).
文摘Liquid structure of molten pure Cu, Cu-12Al, Cu-12Al-4Ni (mass fraction, %) alloys has been investigated using the X-ray diffraction method. It is found that the main peak of the structure factor of pure Cu is symmetrical. In the front of main peak, the curve takes on a shape of parabola, whereas a distinct pre-peak has been found around a scattering vector magnitude of 18.5 nm-1 in the structure factor of the liquid Cu-12Al alloy. This pre-peak increases its inten-sity with the addition of Ni in the liquid Cu-12Al-4Ni alloy. The appearance of a pre-peak is a mark of the mediate-range order. Based on Daken-Gurry theory and according to mu-tual interaction between unlike atoms, the analysis of corre-lation between different composition and liquid structure was done: the strong interaction exists between Cu and Ni, so Cu-Al can form strong chemical bond which causes compound-forming behavior. Therefore, the medium-range size clusters can form in melt. The presence of the pre-peak corresponds to these
