Cu-Al尖晶石氧化物缓释催化剂表面重构对促进甲醇重整反应性能的研究

Cu-Al尖晶石氧化物作为甲醇水蒸气重整制氢缓释催化剂,在反应过程中逐渐释放活性Cu,其催化行为与催化剂的表面结构密切相关。本研究采用酸碱溶液对固相球磨法合成的Cu-Al尖晶石催化剂进行表面处理,以期通过表面组成及结构的修饰来提高其催化性能。研究结果表明,硝酸、氨水、氢氧化钠溶液与催化剂的作用差别极大,酸处理去除了催化剂表面的Cu和Al物种,氢氧化钠溶液处理则主要去除了Al物种,氨水溶液处理作用最弱,去除了极少量的Cu和Al。伴随着Cu、Al物种的流失,催化剂表面结构重组和铜物种再分布改变了铜的缓释行为。反应性能评价结果表明,硝酸和氨水处理改善了缓释催化性能,其中,硝酸处理后的催化剂表现出更优异的催化稳定性;而氢氧化钠溶液处理不利于缓释催化性能的提高。结合反应后催化剂表征结果,阐明缓释Cu粒径大小和Cu晶粒微观结构应变对催化性能发挥着重要作用。当前工作为提高缓释催化提供了一种切实可行的方法。

Cu-Al层状复合材料金属间化合物结构稳定性的第一性原理计算

铜铝层状复合材料在固液复合铸轧成型时,固态铜与液态铝在接触面发生界面反应生成的金属间化合物容易引发晶界脆性、晶间裂纹或弹性畸变致使其开裂而失效。因此,一个强而稳定的界面对于整个复合材料的结构强度至关重要。为深入了解界面金属间化合物的化学键合、晶体结构及稳定性,利用第一性原理对Cu-Al层状复合材料中常见的金属间化合物Al_(4)Cu_(9)、Al_(2)Cu、AlCu开展了热力学性能、力学性能和电子结构的相关计算。有效生成热数值表明,扩散初始阶段Al_(2)Cu相将在界面处最先生成,待Al_(2)Cu初生相形成后,将依次生成Al_(4)Cu_(9)、AlCu。Al_(2)Cu、Al_(4)Cu_(9)和AlCu均符合力学稳定性标准,对比它们的B/G值、泊松比和硬度,3种金属间化合物均为脆性相,其中Al_(2)Cu的脆性最大且硬度最高。通过对能带、态密度和Mulliken布居进行分析,发现金属键在Al_(2)Cu和AlCu化学键中具有更强的离子性特征,而在Al_(4)Cu_(9)化学键中具有更强的共价性特征,使得Al和Cu原子之间的相互作用更紧密,稳定性更强。

铝源对Cu-Al尖晶石物化性质和逆水煤气变换性能的影响

基于高能球磨和固相焙烧的方法,采用杂质元素(Na、Fe、Si和S)含量不等的四种拟薄水铝石和氢氧化铜制备了Cu-Al尖晶石固溶体催化剂,通过ICP-AES、TG、XRD、H2-TPR和BET表征了催化剂的物化性质,并考察了对逆水煤气变换反应的催化性能。结果表明,拟薄水铝石中的杂质元素对于Cu-Al尖晶石催化剂的物相性质、还原性能、织构性质和催化性能有显著的影响,Si有助于合成高比表面积的催化剂,但不利于Cu-Al尖晶石生成,导致催化活性低;含有少量Na和Fe的尖晶石的催化活性较低;S物种经高温焙烧后分解,对催化活性没有影响;基于杂质元素含量最低的拟薄水铝石合成的催化剂中难还原尖晶石含量最高,表现出最高的逆水煤气变换催化活性。此外,基于活性最优样品的CO_(2)-TPDMS和In-situ DRIFTS分析表明,Al上形成的双齿甲酸盐是Cu-Al尖晶石固溶体催化CO_(2)加氢生成CO的主要中间产物,其含量与催化活性随反应时间的变化规律一致。

Microstructure and Properties of AlCoCrFeNiTi High-Entropy Alloy Coatings Prepared by Laser Cladding

21-4N(5Cr21Mn9Ni4N)is extensively employed in the production of engine valves,operating under severe conditions.Apart from withstanding high-temperature gas corrosion,it must also endure the impact of cylinder explosion pressure.The predominant failure mode of 21-4N valves is abrasive wear.Surface coatings serve as an effective approach to prevent such failures.In this investigation,Laser cladding technology was utilized to fabricate AlCoCrFeNiTi high entropy alloy coatings onto the surfaces of 21-4N valves.According to the findings,the cladding zone has a normal dendritic microstructure,a good substrate-to-cladding layer interaction,and no obvious flaws.In terms of hardness,the cladding demonstrates an average hardness of 620 HV.The hardness has increased by 140%compared to the substrate.The average hardness of the cladding remains at approximately 520 HV even at elevated temperatures.Regarding frictional wear performance,between 400℃and 800℃,the cladding layer exhibits an average friction coefficient of 0.4,with the primary wear mechanisms being abrasive wear,adhesive wear,and a minor degree of plastic deformation.

Preparation of Laser Cladding Coating Undercooling Cu-based Alloy and Co on Non-equilibrium Solidification Structure

The effect of the gradient content of Co element on the solidification process of Cu-based alloy under deep under cooling conditions was explored.The non-equilibrium solidification structure of the under cooled alloy samples were analyzed.It is found that the rapidly solidified alloy has undergone twice grain refinement during the undercooling process.Characterization and significance of the maximum undercooling refinement structure of Cu60Ni35Co5 at T=253 K were analyzed.High-density defects were observed,such as dislocations,stacking faults networks,and twinning structures.The standard FCC diffraction pattern represents that it is still a single-phase structure.Based on the metallographic diagram,EBSD and TEM data analysis,it is illustrated that the occurrence of grain refinement under high undercooling is due to stress induced recrystallization.In addition,the laser cladding technology is used to coat Co-based alloy(Stellite12) coating on 304 stainless steel substrate;the microstructure of the coating cross-section was analyzed.It was found that the microstructure of the cross-section is presented as columnar crystals,planar crystals,and disordered growth direction,so that the coating has better hardness and wear resistance.By electrochemical corrosion of the substrate and coating,it can be seen that the Co and Cr elements present in the coating are more likely to form a dense passivation film,which improved the corrosion resistance of the coating.

Ultra wear resistant TiC-Fe coating prepared by high efficient and economic plasma cladding method

The key components of engineering machinery frequently failed due to working in the high load and high wear operating envir-onment.And the performance of the Fe-based alloy coatings typically employed need to be improved for fulfilling the service requirements.Herein,a TiC strengthened Fe-based alloy cladding layer,named TiC-Fe coating,was designed and prepared by plasma cladding technology.The frictional wear performance of coating under various loads was tested.The wear morphology of the coating was observed,and its wear mechanism was examined.The results indicated that the TiC-Fe coating was well formed and metallurgically bonded to the Q345C substrate.Its microstructure mainly consisted of Fe-Cr solid solution,α-Fe phase,(Fe,Cr)_(7)C_(3) phase and TiC phase.The coating exhibited an average microhardness of 980 HV0.2,which was about 5.4 times that of the Q345C substrate.The wear mass loss of the TiC-Fe coatings was much smaller than that of the Q345C substrate,which indicated that the wear resistance of the Q345C coating was superior to the substrate,and the wear mechanism of the coating was mainly attributed to the abrasive wear.

Process Parameters Optimization of Laser Cladding for HT200 with 316L Coating Based on Response Surface Method

In order to improve the sealing surface performance of gray cast iron gas gate valves and achieve precise molding control of the cladding layer,as well as to reveal the influence of laser cladding process parameters on the morphology and structure of the cladding layer,we prepared the 316L coating on HT 200 by using Design-Expert software central composite design(CCD)based on response surface analysis.We built a regression prediction model and analyzed the ANOVA with the inspection results.With a target cladding layer width of 3.5 mm and height of 1.3 mm,the process parameters were optimized to obtain the best combination of process parameters.The microstructure,phases,and hardness variations of the cladding layer from experiments with optimal parameters were analyzed by the metallographic microscope,confocal microscope,and microhardness instrument.The experimental results indicate that laser power has a significant impact on the cladding layer width,followed by powder feed rate;scan speed has a significant impact on the cladding layer height,followed by powder feed rate.The HT200 substrate and 316L can metallurgically bond well,and the cladding layer structure consists of dendritic crystals,columnar crystals,and equiaxed crystals in sequence.The optimal process parameter combination satisfying the morphology requirements is laser power(A)of 1993 W,scan speed(B)of 8.949 mm/s,powder feed rate(C)of 1.408 r/min,with a maximum hardness of 1564.3 HV0.5,significantly higher than the hardness of the HT200 substrate.

Evaluation of Textured Concrete as an Alternative for Stone as a Cladding Material

Along with the increasing demand on exterior wall cladding as a protective cover for the interior elements and an indicator for modernity and architectural innovation,comes the need to develop new cladding materials that can replace the old ones and overcome their setbacks.This paper discusses the possibility of replacing stone by textured concrete as a cladding material in order to overcome the main challenges faced stone cladding by comparing them together.The comparison was made based on the main requirements of the cladding materials namely:economic,environmental,social,functional and structural aspects.

激光烧结原位合成Cu-Al合金组织结构及性能研究

针对铜铝粉末坯体,以激光高能束为热源引发铝热放热反应,原位合成硬质增强相Al_(2)O_(3),烧结制备了Cu-Al合金,研究了铜铝成分配比对合金体系微观组织和性能的影响。结果表明,Cu-Al合金组织是由硬质增强相Al_(2)O_(3)和基体CuAl_(2)、AlCu_(4)、Al_(4)Cu_(9)等金属间化合物构成的多相结构;合金显微组织具有丰富的树枝晶,且随着铝含量增加,组织均匀细化程度提高;在一定范围内,增加铝含量有助于提高烧结产物致密性;当铜铝质量比为33.2∶66.8时,烧结产物的孔隙率最低(10.57%)、显微硬度值最高(373HV)、磨损性最佳(磨损率0.137 g/mm^(2))。

Cu-Al interfacial compounds and formation mechanism of copper cladding aluminum composites

Copper cladding aluminum(CCA)rods with the section dimensions of12mm in diameter and2mm in sheath thickness were fabricated by vertical core-filling continuous casting(VCFC)technology.The kinds and morphology of interfacial intermetallic compounds(IMCs)were investigated by SEM,XRD and TEM.The results showed that the interfacial structure of Cu/Al was mainly composed of layeredγ1(Cu9Al4),cellularθ(CuAl2),andα(Al)+θ(CuAl2)phases.Moreover,residual acicularε2(Cu3Al2+x)phase was observed at the Cu/Al interface.By comparing the driving force of formation forε2(Cu3Al2+x)andγ1(Cu9Al4)phases,the conclusion was drawn that theε2(Cu3Al2+x)formed firstly at the Cu/Al interface.In addition,the interfacial formation mechanism of copper cladding aluminum composites was revealed completely.

Fretting Wear Characteristics of Nuclear Fuel Cladding in High-Temperature Pressurized Water

In pressurized water reactor(PWR),fretting wear is one of the main causes of fuel assembly failure.Moreover,the operation condition of cladding is complex and harsh.A unique fretting damage test equipment was developed and tested to simulate the fretting damage evolution process of cladding in the PWR environment.It can simulate the fretting wear experiment of PWR under different temperatures(maximum temperature is 350℃),displacement amplitude,vibration frequency,and normal force.The fretting wear behavior of Zr-4 alloy under different temperature environments was tested.In addition,the evolution of wear scar morphology,profile,and wear volume was studied using an optical microscope(OM),scanning electron microscopy(SEM),and a 3D white light interferometer.Results show that higher water temperature evidently decreased the cladding wear volume,the wear mechanism of Zr-4 cladding changed from abrasive wear to adhesive wear and the formation of an oxide layer on the wear scar reduced the wear volume and maximum wear depth.

Effects of process parameters and annealing on microstructure and properties of CoCrFeMnNi high-entropy alloy coating prepared by plasma cladding

Plasma cladding was used to prepare a CoCrFeMnNi high-entropy alloy(HEA)coating under different conditions.The process parameters were optimized using an orthogonal experiment design based on surface morphology quality characteristics,dilution rate,and hardness.The optimal process parameters were determined through range and variance analysis to be a cladding current of 70 A,a cladding speed of 7 cm·min^(-1),and a powder gas flow rate of 8 L·s^(-1).During the optimized experiments,both the cladded and annealed CoCrFeMnNi HEA coatings exhibit some pores,micro-voids,and a small amount of aggregation.However,the aggregation in the annealed coating is more dispersed than that in the cladded coating.The cladded CoCrFeMnNi HEA coating consists of simple FCC phases,while a new Cr-rich phase precipitates from the FCC matrix after annealing the coating at a temperature range of 550°C-950°C.After annealing at 850°C,the proportion of the FCC phase decreases compared to the cladded coating,and the number of large-angle grain boundaries is significantly reduced.However,the proportion of grains with sizes below 50μm increases from 61.7%to 74.3%.The micro-hardness and wear resistance of the cladded coating initially increases but then decreases with an increase in annealing temperature,indicating that appropriate annealing can significantly improve the mechanical properties of the CoCrFeMnNi HEA coatings by plasma cladding.The micro-hardness of the CoCrFeMnNi HEA coatings after annealing at 650°C increases to 274.82 HV_(0.2),while the friction coefficient decreases to below 0.595.

Transient fuel performance analysis of UO_(2)–BeO fuel with composite SiC coated with Cr cladding based on multiphysics method

The transient multiphysics models were updated in CAMPUS to evaluate the accident-tolerant fuel performance under accident conditions.CAMPUS is a fuel performance code developed based on COMSOL.The simulated results of the UO_(2)–Zircaloy fuel performance under accident conditions were compared with those of the FRAPTRAN code and the experimental data to verify the correctness of the updated CAMPUS.Subsequently,multiphysics models of the UO_(2)–BeO fuel and composite SiC coated with Cr(SiC_(f)/SiC-Cr)cladding were implemented in CAMPUS.Finally,the fuel performance of the three types of fuel cladding systems under Loss of Coolant Accident(LOCA)and Reactivity Insertion Accident(RIA)conditions was evaluated and compared,including the temperature distribution,stress distribution,pressure evolution,and cladding failure time.The results showed that the fuel temperature of the UO_(2) fuel under accident conditions without pre-irradiation was lower after being combined with SiC_(f)/SiC-Cr cladding.Moreover,the centerline and outer surface temperatures of the UO_(2)–BeO fuel combined with SiC_(f)/SiC-Cr cladding reduced further under accident conditions.The cladding temperature increased after the combination with the SiC_(f)/SiC-Cr cladding under accident conditions with pre-irradiation.In addition,the use of SiC_(f)/SiC-Cr cladding significantly reduced the cladding hoop strain and plenum pressure.

Fiber cladding dual channel surface plasmon resonance sensor based on S-type fiber

Fiber cladding surface plasmon resonance(SPR)sensors have few structures,and a clad SPR sensor based on S-type fiber is proposed in this paper.This new type of fiber cladding SPR sensor was formed by electrofusing an S-shaped structure on the fiber to couple the light in the fiber core to the cladding.In this paper,the effects of fiber parameters on the performance of the sensor were studied by simulation and experiment.Based on the conclusion that the smaller the core diameter is,the closer the working band of the SPR resonance is to long wavelengths,and that the geometric characteristics mean that a multimode fiber can receive the fiber cladding light from a small core diameter few-mode fiber,a dual channel SPR sensor with a double S-type fiber cascade was proposed.In the refractive index detection range of 1.333–1.385refractive index units(RIU),the resonant working band of channel I is 627.66 nm–759.78 nm,with an average sensitivity of 2540.77 nm/RIU,and the resonant working band of channel II is 518.24 nm–658.2 nm,with an average sensitivity of2691.54 nm/RIU.The processing method for the S-type fiber cladding SPR sensor is simple,effectively solving the problem of this type of SPR sensor structure and the difficult realization of a dual channel.The sensor is expected to be used in the fields of medical treatment and biological analysis.

A cladding-pumping based power-scaled noise-like and dissipative soliton pulse fiber laser

We report a high-average-power noise-like pulse(NLP) and dissipative soliton(DS) pulse fiber laser. Average power as high as 4.8 W could be obtained at the fundamental mode-locked repetition rate. The NLP can also be transformed into a more powerful DS mode-locking state by optimizing the polarization and losses of intra-cavity pulses in the nonlinear polarization evolution regime. The operation mode between the NLP and DS can be switched, and the laser output performance in both modes has been studied. The main advantage of this work is switchable high-power operation between the NLP and DS. In comparison with conventional single-mode NLP fiber lasers, the multi-function high-power optical source will greatly push its application in supercontinuum generation, coherence tomography, and industrial processing.

Cu-Al复合材料热性能实验研究

为探究Cu-Al复合材料界面对室温环境下导热性能的影响,通过研究热处理工艺条件对Cu-Al复合材料界面扩散层影响规律,揭示Cu-Al复合板导热机制。研究表明,当Cu、Al厚度比为1∶1,退火温度为400℃时,Cu-Al复合材料室温条件下热导率为37.26 W/(m·K),其导热性能最好,界面的扩散相主要为AlCu和Al 2Cu。在400℃退火热处理下,传热方式主要受界面结构影响,界面产生中间相的数量影响复合板导热性能,趋近于两种不同材质中间区域。随着保温时间延长,AlCu相增多,对于薄壁件其室温导热性能受界面组分影响较大。通过流延法所制备的Cu-Al复合板热处理后界面光滑、平整,热处理后界面层扩散明显。

Numerical simulation of a truncated cladding negative curvature fiber sensor based on the surface plasmon resonance effect

A refractive index(RI)sensor based on the surface plasmon resonance effect is proposed using a truncated cladding negative curvature fiber(TC-NCF).The influences of the TC-NCF structure parameters on the sensing performances are investigated and compared with the traditional NCF.The simulation results show that the proposed TC-NCF RI sensor has an ultra-wide detection range from 1.16 to 1.43.The maximum wavelength sensitivity reaches 12400 nm/RIU,and the corresponding R^(2)of the polynomial fitting equation is 0.9999.The maximum and minimum resolutions are 2.56×10^(-5)and 8.06×10^(-6),respectively.In addition,the maximum amplitude sensitivity can reach-379.1 RIU^(-1)when the RI is chosen as 1.43.The proposed TC-NCF RI sensor could be useful in biochemical medicine,environmental monitoring,and food safety.

Cr_(3)C_(2)/WC的添加对Stellite 12熔覆层耐磨耐蚀性的影响

目的 提高Stellite 12熔覆层的耐磨耐蚀性能。方法将Stellite 12合金粉末与碳化物(Cr_(3)C_(2)、WC)混合,采用激光熔覆技术在H13钢板上制备复合熔覆层。通过超景深显微镜和XRD分析其显微组织和物相,通过显微硬度测试、摩擦磨损试验和电化学腐蚀试验,分别评价熔覆层的硬度、耐磨性和耐蚀性,并通过超景深显微镜对磨痕形貌进行分析。结果添加碳化物后,熔覆层的微观组织以柱状晶和树枝晶为主,物相主要由γ-Co固溶体和碳化物(M23C6、M7C3)组成;Cr_(3)C_(2)的添加使得熔覆层的硬度降低,由610HV0.2降至530HV0.2,但耐磨性得到提高,磨损量由0.45 mm^(3)降至0.33 mm^(3),下降了28%,耐蚀性得到提高,腐蚀电位由-0.385 V增加到-0.264 V,腐蚀电流密度由9.269×10^(-10)A/cm^(2)降至1.496×10^(-10)A/cm^(2),极化电阻由3.982×10^(7)Ω·cm^(2)提升至2.424×10^(8)Ω·cm^(2),提高了1个数量级;WC的添加使其硬度由610HV0.2提高至750HV0.2,磨损深度变浅,磨损量由0.45 mm3降至0.19 mm^(3),下降了43%,但耐腐蚀性有所降低。3种熔覆层的磨损机制主要为磨粒磨损和黏着磨损。结论WC的添加可以有效提高熔覆层的硬度和耐磨性,但耐腐蚀性有所降低;添加Cr_(3)C_(2)后,耐蚀性得到显著提高,耐磨性略微提升,但硬度降低。

热塑型聚酰亚胺的制备及其粘接性能研究

为了改善两层型挠性覆铜板(2L-FCCL)中热塑型聚酰亚胺(TPI)对热固型聚酰亚胺(PI)薄膜和铜箔的粘接性,本文选用具有柔性结构的芳香二酐单体和芳香或脂环的二异氰酸酯单体通过一步反应制备得到TPI样品,然后将其直接涂覆在表面经过预处理的商品化热固型PI薄膜上得到复合膜,最后经过高温热压得到相应的2L-FCCL。通过观察所得TPI反应液的状态并进行DSC测试,选定了有机溶剂可溶且Tg为226.5℃的TPI-8;然后通过TGA、TMA和拉伸试验测得TPI-8的2%热分解温度(T2%)为464℃、50~200℃的热膨胀系数(CTE)为64.25×10^(-6)℃^(-1)、拉伸强度为64.52MPa、弹性模量为1.75 GPa、断裂伸长率为62%,并通过FTIR对其化学结构进行了确认;最后分别研究了两种热固型PI薄膜的碱水预处理时间对所得FCCL粘接性能的影响,发现其中SPI膜经60℃碱水处理1 min和3 min后得到的FCCL90°剥离强度(90°PS)≥0.7 N/mm且最大值达到0.94 N/mm,而UPI膜经同样热碱水处理1~7 min后得到的FCCL 90°PS均≤0.6 N/mm。因此,采用本方法可一步快速简单的制备可溶解且热学性能、力学性能、尺寸稳定性较好的TPI,同时其对铜箔以及表面经过碱水预处理的SPI具有较好的粘接性能,满足FCCL相关标准的要求。

碳氢树脂高频覆铜板的研究进展

本文综述了高频覆铜板的特点,并对其基体树脂的介电性能进行对比,重点介绍了碳氢树脂(PCH)高频覆铜板的研究进展。通过对目前碳氢树脂高频覆铜板研究的总结,找出现存的问题并对其未来发展趋势进行展望。