Electrochemical behavior of Cu-Zn-Al shape memory alloy after surface modification by electroless plated Ni-P

The electrochemical behavior of Cu-Zn-Al shape memory alloy (SMA) with andwithout electroless plated Ni-P was investigated by electrochemical methods, in artificial Tyrode'ssolution. The results showed that Cu-Zn-Al SMA engendered dezincification corrosion in Tyrode'ssolution. The anodic active current densities as well as electrochemical dissolution sensitivity ofthe electroless plated Ni-P Cu-Zn-Al SMA increased with NaCl concentration rising, pH of solutiondecreasing and environmental temperature uprising. X-ray diffraction analysis indicated that aftersurface modification by electroless plated Ni-P, an amorphous plated film formed on the surface ofCu-Zn-Al SMA. This film can effectively isolate matrix metal from corrosion media and significantlyimprove the electrochemical property of Cu-Zn-Al SMA in artificial Tyrode's solution.

Pitting Corrosion of Cu-Zn-Al Shape Memory Alloy in Simulated Uterine Fluid

Electrochemical test technology and surface analysis method were employed to investigate the pitting corrosion of Cu-Zn-AI shape memory alloy in simulated uterine fluid. The results showed that the breakage of the breaking-renovating equilibrium of surface layers resulted in the pitting corrosion of Cu-Zn-AI shape memory alloy in simulated uterine fluid. The development of pitting corrosion was controlled by dissolution of surface layers. The critical pitting corrosion potential was 1.70 VSCE. The kinetics equation for the development of pitting corrosion for Cu-Zn-AI shape memory alloy in simulated uterine fluid was io=465.68 t-0.5+1.5. Pitting appearances of pits could be two types: tortoise-shell, and anomaly abscess. Cl- ion facilitated the pitting corrosion of Cu-Zn-AI shape memory alloy by competing adsorption and concentrating on alloy surface at high positive potential.

QUANTITATIVE CHARACTERIZATION OF STRESS-STRAIN HYSTERESIS LOOPS OF Cu-Zn-Al SHAPE MEMORY ALLOY

A six-parameter mathematical model was introduced to simulate the stress-strain hysteresis and the sinner hysteresis of polycrystalline shape memory alloys (SMAs). By the comparison with experiments of Cu-Zn-Al SMA, it was shown that the model could be used to calculate the stress-strain relations with rather good accuracy. Moreover, it was found that the six parameters introduced in this paper represented the characteristics of the stress-strain hysteresis of polycrystalline SMAs and could be used to characterize the hysteresis quantitatively.

STABILITIY OF MARTENSITE IN Cu-Zn-Al SHAPE MEMORY ALLOY AFTER DIRECT OR STEPPED QUENCHING

The stability of thermoelastic martensite in a Cu-14.84 wt-％Zn-7.75 wt-％Al shape mem- ory alloy with M_s=106°C after direct quenching or stepped quenching has been investigated by using TEM,X-ray diffroctometer and double electric bridge instrument.The martensite aged for about 3 h at room temperature after either direct quenching or stepped quenching (150°C,2 rain)is the M18R structure.The martensite just directly quenched is not so stable, both its certain diffraction peaks and specific electric resistivity,change with aging at room temperature;whereas it is stable after stepped quenching(150°C.2 min),and its diffraction peaks and specific electric resistivity change no more with aging at room temperature.The above mentioned results seem to be explained by the martensite reordering.

Damping performance of Cu-Zn-Al shape memory alloys in engineering structures

The stress strain curves of two CuZnAl shape memory alloys which have the martensitic transformation temperatures of 50 ℃ and -10 ℃ respectively, were measured by using electronic material tester after treated by different heat-treatment conditions. The results show that the area enclosed by hysteresis loop of the CuZnAl shape memory alloy in martensitic state is much larger than that of the alloy in austenitic state with super-elasticity at room temperature. Therefore, the former has better vibration attenuation effect. After being oil-quenched, water-quenched, and step-quenched, the CuZnAl alloy takes on more stable shape memory effect,better super-plasticity and superelasticity (pseudoelasticity). A CuZnAl shape memory alloy damper was designed, produced and installed to a 2-layer frame structure. In addition, the vibration experiments were made by dynamic data collecting analysis meter. The velocity of vibration attenuation of frame structure with CuZnAl shape memory alloy damper is much faster than that without it. And with the help of CuZnAl shape memory alloy damper, the attenuation period reduces to 1/10 of the original.

Cooling rate effects on the structure and transformation behavior of Cu-Zn-Al shape memory alloys

Different fragments of a hot-rolled and homogenized Cu–Zn–Al shape memory alloy（SMA） were subjected to thermal cycling by means of a differential scanning calorimetric（DSC） device. During thermal cycling, heating was performed at the same constant rate of increasing temperature while cooling was carried out at different rates of decreasing temperature. For each cooling rate, the temperature decreased in the same thermal interval. During each cooling stage, an exothermic peak（maximum） was observed on the DSC thermogram. This peak was associated with forward martensitic transformation. The DSC thermograms were analyzed with PROTEUS software： the critical martensitic transformation start（Ms） and finish（Mf） temperatures were determined by means of integral and tangent methods, and the dissipated heat was evaluated by the area between the corresponding maximum plot and a sigmoid baseline. The effects of the increase in cooling rate, assessed from a calorimetric viewpoint, consisted in the augmentation of the exothermic peak and the delay of direct martensitic transformation. The latter had the tendency to move to lower critical transformation temperatures. The martensite plates changed in morphology by becoming more oriented and by an augmenting in surface relief, which corresponded with the increase in cooling rate as observed by scanning electron microscopy（SEM） and atomic force microscopy（AFM）.

Corrosion resistance of benzotriazole passivated Cu-Zn-Alshape memory alloy in artificial Ringer's solution

The corrosion resistance of the Cu-Zn-Al shape memory alloy passivated by benzotriazole was investigated by salt spraying test and electrochemical methods in artificial Ringer＇s solution. The results showed that after benzotriazole passivation, the corrosion resistance of the Cu-Zn-Al shape memory alloy was improved evidently. The anodic polarization current density of the passivated alloy decreased, the mass loss reduced, the anodic passivation accelerated, the anodic active dissolution was inhibited effectively, and the surface tarnishing was reswained. Infrared reflection spectrum test showed that Cu（Ⅰ）-benzotriazole or Cu（Ⅱ）-benzotriazole complex layer was formed on the surface of the Cu-Zn-Al shape memory alloy after passivation. This layer appeared plane, well adhesion, and presented homogeneous golden metallic luster. The corrosion resistance of the Cu-Zn-Al shape memory alloy passivated by benzotriazole is improved for the formation of an electrochemical stable baffle layer on passivated surface. This layer separates the metal substrate from the outside corrosion medium effectively and retards the corrosion process of dezincification.

Machine learning-assisted efficient design of Cu-based shape memory alloy with specific phase transition temperature

The martensitic transformation temperature is the basis for the application of shape memory alloys(SMAs),and the ability to quickly and accurately predict the transformation temperature of SMAs has very important practical significance.In this work,machine learning(ML)methods were utilized to accelerate the search for shape memory alloys with targeted properties(phase transition temperature).A group of component data was selected to design shape memory alloys using reverse design method from numerous unexplored data.Component modeling and feature modeling were used to predict the phase transition temperature of the shape memory alloys.The experimental results of the shape memory alloys were obtained to verify the effectiveness of the support vector regression(SVR)model.The results show that the machine learning model can obtain target materials more efficiently and pertinently,and realize the accurate and rapid design of shape memory alloys with specific target phase transition temperature.On this basis,the relationship between phase transition temperature and material descriptors is analyzed,and it is proved that the key factors affecting the phase transition temperature of shape memory alloys are based on the strength of the bond energy between atoms.This work provides new ideas for the controllable design and performance optimization of Cu-based shape memory alloys.

Effect of solution treatment on the microstructure,phase transformation behavior and functional properties of NiTiNb ternary shape memory alloys fabricated via laser powder bed fusion in-situ alloying

Post-heat treatment is commonly employed to improve the microstructural homogeneity and enhance the mechanical performances of the additively manufactured metallic materials.In this work,a ternary(NiTi)91Nb9(at.%)shape memory alloy was produced by laser powder bed fusion(L-PBF)using pre-alloyed NiTi and elemental Nb powders.The effect of solution treatment on the microstructure,phase transformation behavior and mechanical/functional performances was investigated.The in-situ alloyed(NiTi)91Nb9 alloy exhibits a submicron cellular-dendritic structure surrounding the supersaturated B2-NiTi matrix.Upon high-temperature(1273 K)solution treatment,Nb-rich precipitates were precipitated from the supersaturated matrix.The fragmentation and spheroidization of the NiTi/Nb eutectics occurred during solution treatment,leading to a morphological transition from mesh-like into rod-like and sphere-like.Coarsening of theβ-Nb phases occurred with increasing holding time.The martensite transformation temperature increases after solution treatment,mainly attributed to:(i)reduced lattice distortion due to the Nb expulsion from the supersaturated B2-NiTi,and(ii)the Ti expulsion from theβ-Nb phases that lowers the ratio Ni/Ti in the B2-NiTi matrix,which resulted from the microstructure changes from non-equilibrium to equilibrium state.The thermal hysteresis of the solutionized alloys is around 145 K after 20%pre-deformation,which is comparable to the conventional NiTiNb alloys.A short-term solution treatment(i.e.at 1273 K for 30 min)enhances the ductility and strength of the as-printed specimen,with the increase of fracture stress from(613±19)MPa to(781±20)MPa and the increase of fracture strain from(7.6±0.1)%to(9.5±0.4)%.Both the as-printed and solutionized samples exhibit good tensile shape memory effects with recovery rates>90%.This work suggests that post-process heat treatment is essential to optimize the microstructure and improve the mechanical performances of the L-PBF in-situ alloyed parts.

Improving comprehensive properties of Cu-11.9Al-2.5Mn shape memory alloy by adding multi-layer graphene carried by Cu_(51)Zr_(14)inoculant particles

In order to improve the comprehensive properties of the Cu-11.9Al-2.5Mn shape memory alloy(SMA),multilayer graphene(MLG)carried by Cu_(51)Zr_(14)inoculant particles was incorporated and dispersed into this alloy through preparing the preform of the cold-pressed MLG-Cu_(51)Zr_(14)composite powders.In the resultant novel MLG/Cu-Al-Mn composites,MLG in fragmented or flocculent form has a good bonding with the Cu-Al-Mn matrix.MLG can prevent the coarsening of grains of the Cu-Al-Mn SMA and cause thermal mismatch dislocations near the MLG/Cu-Al-Mn interfaces.The damping and mechanical properties of the MLG/Cu-Al-Mn composites are significantly improved.When the content of MLG reaches 0.2 wt.%,the highest room temperature damping of 0.0558,tensile strength of 801.5 MPa,elongation of 10.8%,and hardness of HV 308 can be obtained.On the basis of in-depth observation of microstructures,combined with the theory of internal friction and strengthening and toughening theories of metals,the relevant mechanisms are discussed.

MICROSTRUCTURE AND REVERSE SHAPE MEMORY EFFECT IN A Cu-Zn-Al ALLOY

The bainite structure in a Cu-Zn-A1 alloy related to the reverse shape memory effect has been observed by means of TEM.The reverse memory effect may be improved by up to one order of magnitude under applied constraint stress.The widespread propagation of bainite was confirmed to be the diffusion controlled shear process by the parabolic configuration of side interface of bainite plate and the twisting of intersected bainite plates.

Internal Friction in a Shape Memory Alloy Cu-Zn-Al under Equilibrium Condition

1. Introduction CuZnAl shape memory alloys have beenextensively studied as a new type of material.Dejonghe[1]et al. firstly reported theirresults on the internal friction (IF) of CuZnAlalloys in 1975. Later, some researchershave done much work on internal friction.But most of them were concerned withphase transformation internal frictionof martensite and reverse martensite andfew of them were about internal friction

Prediction of Pseudoelastic Elongation in Cu-Zn-AlShape Memory Alloy

The pseudoelastic elongation (P.E.) of β-phase in Cu-Zn-Al SMA (shape memory alloy) was estimated by using the orientation dependence of transformation strain (Taylor model) and texture analysis. It was found that the pseudoelastic elongation is closely related to f(g) of the (001) 〈110〉 texture component in the CuZnAl SMA sheet. The stronger the (001) 〈110〉 texture, the higher value of pseudoelastic elongation is. For the wires, the estimated pseudoelastic elongation decreases with increasing reduction.

Effect of solution treatment and aging on microstructural evolution and mechanical behavior of NiTi shape memory alloy

As-received nickel-titanium （NiTi） shape memory alloy with a nominal composition of Ni50.9Ti49.1 （mole fraction,%） was subjected to solution treatment at 1123 K for 2 h and subsequent aging for 2 h at 573 K, 723 K and 873 K, respectively. The influence of solution treatment and aging on microstructural evolution and mechanical behavior of NiTi alloy was systematically investigated by transmission electron microscopy （TEM）, high resolution transmission electron microscopy （HRTEM）, scanning electron microscopy （SEM） and compression test. Solution treatment contributes to eliminating the Ti2Ni phase in the as-received NiTi sample, in which the TiC phase is unable to be removed. Solution treatment leads to ordered domain of atomic arrangement in NiTi alloy. In all the aged NiTi samples, the Ni4Ti3 precipitates, the R phase and the B2 austenite coexist in the NiTi matrix at room temperature, while the martensitic twins can be observed in the NiTi samples aged at 873 K. In the NiTi samples aged at 573 and 723 K, the fine and dense Ni4Ti3 precipitates distribute uniformly in the NiTi matrix, and thus they are coherent with the B2 matrix. However, in the NiTi sample aged at 873 K, the Ni4Ti3 precipitates exhibit the very inhomogeneous size, and they are coherent, semi-coherent and incoherent with the B2 matrix. In the case of aging at 723 K, the NiTi sample exhibits the maximum yield strength, where the fine and homogeneous Ni4Ti3 precipitates act as the effective obstacles against the dislocation motion, which results in the maximum critical resolved shear stress for dislocation slip.

Crystallization of amorphous NiTi shape memory alloy fabricated by severe plastic deformation

Based on the local canning compression,severe plastic deformation（SPD） is able to lead to the almost complete amorphous nickel-titanium shape memory alloy（NiTi SMA）,in which a small amount of retained nanocrystalline phase is embedded in the amorphous matrix.Crystallization of amorphous NiTi alloy annealed at 573,723 and 873 K was investigated,respectively.The crystallization kinetics of the amorphous NiTi alloy can be mathematically described by the Johnson-MehlAvrami-Kolmogorov（JMAK） equation.NiTi SMA with a complete nanocrystalline phase is obtained in the case of annealing at 573 K and 723 K,where martensite phase transformation is suppressed due to the constraint of the grain boundaries.Crystallization of amorphous NiTi alloy at 873 K leads to the coarse-grained NiTi sample,where（001） martensite compound twin is observed at room temperature.It can be found that the martensitic twins preferentially nucleate at the grain boundary and they grow up towards the two different grains.SPD based on the local canning compression and subsequent annealing provides a new approach to obtain the nanocrystalline NiTi SMA.

Dynamic recovery and dynamic recrystallization of NiTi shape memory alloy under hot compression deformation

Mechanical behavior of nickel？titanium shape memory alloy（NiTi SMA） under hot deformation was investigated according to the true stress—strain curves of NiTi samples under compression at the strain rates of 0.001-1 s-1 and at the temperatures of 600？1000℃.Dynamic recovery and dynamic recrystallization of NiTi SMA were systematically investigated by microstructural evolution.The influence of the strain rates,the deformation temperatures and the deformation degree on the dynamic recovery and dynamic recrystallization of NiTi SMA was obtained as well.NiTi SMA was characterized by the combination of dynamic recovery and dynamic recrystallization at 600℃ and 700℃,but the complete dynamic recrystallization occurred at other deformation temperatures.Increasing the deformation temperatures or decreasing the stain rates leads to larger equiaxed grains.The deformation degree has an important influence on the dynamic recrystallization of NiTi SMA.There exists the critical deformation degree during the dynamic recrystallization of NiTi SMA,beyond which the larger deformation degree contributes to obtaining the finer equiaxed grains.

Effects of second phases on mechanical properties and martensitic transformations of ECAPed TiNi and Ti-Mo based shape memory alloys

TiNi and Ti-based shape memory alloys were processed by equal channel angular pressing （ECAP） at 673-773 K along Bc route to obtain ultrafine grains for increasing the strength of parent phase and improving the functional properties. The effects of both thermodynamically stable and metastable second phases on the mechanical properties and martensitic transformations of these alloys were investigated. It is found that thermodynamically stable Ti2Ni phase has no effect on martensitic transformation and superelasticity of Ti-rich TiNi alloy, thermodynamically stable α phase is harmful for ductility of Ti-Mo-Nb-V-Al alloy, but metastable Ti3Ni4 phase is effective for R phase transformation, martensitic transformation and superelasticity of Ni-rich TiNi alloy. The mechanisms of the second phases on the martensitic transformations and mechanical properties were discussed.

Influence of Ni_4Ti_3 precipitates on phase transformation of NiTi shape memory alloy

Ni Ti shape memory alloy samples were aged for 2 h at 573, 723 and 873 K, respectively. Two R-phase variants are observed in the Ni Ti samples aged at 573 and 723 K, where the orientation relationship between the two R-phase variants and the B2 matrix is determined. In the Ni Ti samples aged at 573 and 723 K, fine and homogeneous Ni4Ti3 precipitates are coherent with the B2 austenite matrix. The Ni4Ti3 particles precipitate in the grain interior and at the grain boundaries, where the heterogeneous Ni4Ti3 precipitates are coherent, semi-coherent and incoherent with the B2 matrix in the Ni Ti sample aged at 873 K. As for the Ni Ti sample aged at 873 K, one-stage phase transformation from B19＇ martensite to B2 austenite occurs on heating, but two-stage phase transformation of B2-R-B19＇ arises on cooling. The Ni Ti sample aged at 723 K shows two-stage phase transformation of B2-R-B19＇ on cooling as well, but exhibits two-stage phase transformation of B19＇-R-B2 on heating. The Ni Ti sample aged at 573 K exhibits three-stage transformation on cooling due to local stress inhomogeneity and local composition inhomogeneity around the Ni4Ti3 precipitates.

Plastic yielding of NiTi shape memory alloy under local canning compression

As a new attempt, local canning compression was applied in order to implement large plastic deformation of nickel-titanium shape memory alloy （NiTi SMA） at room temperature. The plastic mechanics of local canning compression of NiTi SMA was analyzed according to the slab method as the well as plastic yield criterion. Transmission electron microscopy （TEM）, high resolution transmission electron microscopy （HRTEM） and scanning electron microscopy （SEM） were used to study the microstructural evolution as well as deformation behavior of NiTi samples under local canning compression. Increasing the hydrostatic pressure with the increase in the outer diameters of the steel cans is responsible for suppressing the initiation and growth of the micro-cracks, which contributes to enhancing the plasticity ofNiTi SMA and avoiding the occurrence of brittle fracture. Plastic deformation of NiTi SMA under a three-dimensional compressive stress state meets von-Mises yield criterion at the true strains ranging from about 0.15 to 0.50, while in the case of larger plastic strain, von-Mises yield criterion is unable to be met since the amorphous phase arises in the deformed NiTi sample.

Influence of cooling rate on phase transformation and microstructure of Ti-50.9%Ni shape memory alloy

Heat treatment of Ti-50.9%Ni （mole fraction） alloy was studied by differential scanning calorimetry, X-ray diffraction, scanning electron microscopey and energy dispersive X-ray analysis to investigate the influence of cooling rate on transformation behavior and microstructures of NiTi shape memory alloy. The experimental results show that three-stage phase transformation can be induced at a very low cooling rate such as cooling in furnace. The cooling rate also has a great influence on the phase transformation temperatures. Both martensitic start transformation temperature （Ms） and martensitic finish transformation temperature （Mf） decrease with the decrease of the cooling rate, and decreasing the cooling rate contributes to enhancing the M→A austenite transformation temperature. The phase transformation hysteresis （Af-Mf） increases with the decrease of the cooling rate. Heat treatment is unable to eliminate the textures formed in hot working of NiTi sample, but can weaken the intensity of them. The cooling rate has little influence on the grain size.