Two Al2O3/Cu composites containing 0.24 wt.% Al2O3 and 0.60 wt.% Al2O3 separately are prepared by internal oxidation. Effects of sliding speed and pressure on the frictional characteristics of the composites and coppe...Two Al2O3/Cu composites containing 0.24 wt.% Al2O3 and 0.60 wt.% Al2O3 separately are prepared by internal oxidation. Effects of sliding speed and pressure on the frictional characteristics of the composites and copper against brass are investigated and compared. The changes in morphology of the sliding surface and subsurface are examined with scanning electron microscope （SEM） and energy dispersive X-ray spectrum （EDS）. The results show that the wear resistance of the Al2O3/Cu composites is superior to that of copper under the same conditions, Under a given electrical current, the wear rate of Al2O3/Cu composites decreases as the Al2O3-content increases, However, the wear rates of the Al2O3/Cu composites and copper increase as the sliding speed and pressure increase under dry sliding condition. The main wear mechanisms for Al2O3/Cu composites are of abrasion and adhesion; for copper, it is adhesion, although wear by oxidation and electrical erosion can also be observed as the speed and pressure rise.展开更多
A heat-resistant dispersion-strengthening nano-Al_2O_3/Cu composite with highstrength and high electric conductivity was fabricated in a multiplex medium. The internaloxidation product, microstructures and properties ...A heat-resistant dispersion-strengthening nano-Al_2O_3/Cu composite with highstrength and high electric conductivity was fabricated in a multiplex medium. The internaloxidation product, microstructures and properties of the composite, and the process flow weresystematically studied. It is confirmed that this new technique simplifies the process and improvesthe properties of the composite. X-ray analysis indicates that the alumina particles formed duringinternal oxidation consist of a large mount of gamma-Al_2O_3 and a certain amount of theta-Al_2O_3and alpha-Al_2O_3. TEM observation shows that the obtained gamma-Al_2O_3 nano-particles areuniformly distributed in the copper grains; their mean size and space between particles are 7 runand 30 nm, respectively. The main properties of the composite with 50 percent cold deformation areas follows: the electric conductivity is 51 MS/m (87 percent IACS), sigma_b = 628 MPa, and thehardness is HRB86. After annealing at 1273 K, all or most of the above properties remain, and themicrostructures are still dependent on elongated fiber-form grains.展开更多
The(Cu−10Sn)−Ni−MoS2 composites,prepared by powder metallurgy,were studied for the effects of Ni-coated MoS2 on the microstructure,mechanical properties and lubricating properties.The mechanism of effects of Ni and Mo...The(Cu−10Sn)−Ni−MoS2 composites,prepared by powder metallurgy,were studied for the effects of Ni-coated MoS2 on the microstructure,mechanical properties and lubricating properties.The mechanism of effects of Ni and MoS2 on the properties of composites was analyzed through a comparative experiment by adding Ni and MoS2 separately.The results show that the nickel wrapping around the MoS2 particles decreases the reaction rate of MoS2 with the copper matrix,and greatly improves the bonding of the matrix.The composites with 12 wt.%Ni-coated MoS2(C12)show the optimum performance including the mechanical properties and tribological behaviors.Under oil lubrication conditions,the friction coefficient is 0.0075 with a pressure of 8 MPa and a linear velocity of 0.25 m/s.The average dry friction coefficient,sliding against 40Cr steel disc,is measured to be 0.1769 when the linear velocity and pressure are 0.25 m/s and 4 MPa,respectively.展开更多
TiC-TiB2-Cu composites were produced by self-propagating high-temperature synthesis combined with pseudo hot isostatic pressing using Ti, B4C and Cu powders. The microstructure and mechanical properties of the composi...TiC-TiB2-Cu composites were produced by self-propagating high-temperature synthesis combined with pseudo hot isostatic pressing using Ti, B4C and Cu powders. The microstructure and mechanical properties of the composites were investigated. The X-ray diffraction （XRD） and scanning electron microscopy （SEM） results showed that the final products were only TiC, TiB2 and Cu phases. The clubbed TiB2 grains and spheroidal or irregular TiC grains were found in the microstructure of synthesized products. The reaction temperature and grain size of TiB2 and TiC particles decreased with increasing Cu content. The introduction of Cu into the composites resulted in a drastic increase in the relative density and flexual strength, and the maximum values were obtained with the addition of 20 wt pct, while the fracture toughness was the best when Cu content was 40 wt pct.展开更多
The preferred internal oxidation of aluminum in Cu Al alloy was used to obtain in situ Al 2O 3/Cu composites. The reinforcement particles were mainly γ Al 2O 3, some θ Al 2O 3 and a little α Al 2O 3. Thermodynamics...The preferred internal oxidation of aluminum in Cu Al alloy was used to obtain in situ Al 2O 3/Cu composites. The reinforcement particles were mainly γ Al 2O 3, some θ Al 2O 3 and a little α Al 2O 3. Thermodynamics analyses show that the chemical reactions are 3Cu 2O+2Al=6Cu+Al 2O 3 or 3CuO+2Al=3Cu+Al 2O 3. A related equilibrium diagram was drawn. The experiments and investigation show that the formation rate of Al 2O 3 was controlled by the diffusion of oxygen in matrix.展开更多
In situ TiB2/Cu composites were fabricated by both solid-liquid(S-L)and liquid-liquid(L-L)reactive spray deposition in combination with cold rolling and annealing.The microstructure and properties of the fabricated Ti...In situ TiB2/Cu composites were fabricated by both solid-liquid(S-L)and liquid-liquid(L-L)reactive spray deposition in combination with cold rolling and annealing.The microstructure and properties of the fabricated TiB2/Cu composites were investigated.The results show that the reactive mode and rolling treatment are the main factors affecting the microstructure and properties of the TiB2/Cu composite.The in situ reaction in the L-L reaction can be carried out more completely.By controlling the rolling and annealing process,the relative density and the properties of the as-deposited composites are optimized.The comprehensive performance of the deformed TiB2/Cu composite prepared by L-L reactive spray deposition(401 MPa and 83.5%IACS)is better than that by S-L reactive spray deposition(520 MPa and 20.2%IACS).展开更多
2-D nanosheet Cu2O doped CuO coating poly m-phenylenediamine and melamine/graphene/carbon fibers composite(CuxO/MPM/GFs)was firstly fabricated by compound electrochemical method.CuxO/MPM/GFs was successfully used to t...2-D nanosheet Cu2O doped CuO coating poly m-phenylenediamine and melamine/graphene/carbon fibers composite(CuxO/MPM/GFs)was firstly fabricated by compound electrochemical method.CuxO/MPM/GFs was successfully used to the recovery of iodide(I-)from salt water by lower potential-aided sorption and desorption processes.The potential-aided recovery of I-at CuxO/MPM/GFs was characterized by FE-SEM,XRD,IR,Raman,XPS,UV-vis and electrochemical techniques in detail.The maximal adsorption capacity of 86.82 mg·g^-1 could be obtained with a pseudo-second-order model at 0.8 V for 210 min in pH 5.0,0.1 mol·L^-1 NaCl,and the process accompanied the generation of CuI,CuO and I5-.The I-could be quickly desorbed from the electrode with a transfer of CuI to Cu2O by cycle voltammetry from-1.0 to 0.5 V for 90 cycles in pH 9.0,0.1 mol·L^-1 KNO3.Thus,CuxO/MPM/GFs was renewable in the continuous electrochemical-adsorption-desorption processes.展开更多
Alumina dispersion strengthened copper composite （nano-Al2O3/Cu composite） was recently emerged as a kind of potentially viable and attractive engineering material for applications requiring high strength, high ther...Alumina dispersion strengthened copper composite （nano-Al2O3/Cu composite） was recently emerged as a kind of potentially viable and attractive engineering material for applications requiring high strength, high thermal and electrical conductivities and resistance to softening at elevated temperatures. The nano-Al2O3/Cu composite was produced by internal oxidation. The microstructures of the composite were analyzed by the TEM and its hot deformation behavior was investigated by means of continuous compression tests performed on a Gleeble 1500 thermo-simulator. Making use of the modified algorithm-Levenberg-Marquardt （L-M） algorithm BP neural network, a model for predicting the flow stresses during hot deformation was set up on the base of the experimental data. Results show that the microstructures of the composite are characterized by uniform distribution of nano-Al2O3 particles in Cu-matrix. The sliding of dislocations is the main deformation mechanism. The dynamic recovery is the main softening mode with the flow stress decreasing gently from 500℃ to 850 ~C. The recrystallization of Cu-matrix can be retarded late into as high as 850 ℃, when it happens only partially. The well-trained BP neural network model can accurately describe the influence of the temperature, strain rate, and true strain on the flow stresses, therefore, it can precisely predict the flow stresses of the composite under given deforming conditions and provide a new way to optimize hot deforming process parameters.展开更多
A copper matrix composite reinforced by TiB_2 particle was fabricated by reactions of Cu,Ti and B powders.The microstructure and mechanical properties of the in situ composite were investigated.The results showed that...A copper matrix composite reinforced by TiB_2 particle was fabricated by reactions of Cu,Ti and B powders.The microstructure and mechanical properties of the in situ composite were investigated.The results showed that the in situ formed TiB_2 particles,which has a size of no larger than 1 μm,exhibits a uniform distribution in the copper matrix.Due to TiB_2 reinforcement,the mechanical properties in terms of Young's modulus and yield and ultimate tensile stress of the in situ TiB_2/Cu composite are improved greatly.In addition,even if the volume fraction of TiB_2 reinforcement are the same,the composite in the present study containing fine TiB_2 particles exhibits much higher properties than that of the composite reinforced with coarse ones.展开更多
The effects of reduction ratio during roll bonding on the microstructural evolution at interface and subsequent mechanical properties of roll-bonded Al/Cu 2-ply sheets were investigated. The interface microstructures ...The effects of reduction ratio during roll bonding on the microstructural evolution at interface and subsequent mechanical properties of roll-bonded Al/Cu 2-ply sheets were investigated. The interface microstructures for several Al/Cu 2-ply sheets fabricated under different reduction ratios between 30% and 65% were verified by transmission electron microscopy(TEM). Taking the difference of interface microstructure into consideration, 3-point bending and peel tests were performed for obtaining flexural and bonding strengths for Al/Cu 2-ply sheets. The effect of the quantified areas of metallurgical bonding at interfaces on the bonding strength was also discussed. The results show that both the bonding and flexural strengths for Al/Cu 2-ply sheets are reduced by decreasing the reduction ratio during the roll bonding process, which is strongly correlated with the interface microstructure. This was especially verified by observing the interface delamination from the 3-point bent samples.展开更多
This work concerns with the high temperature deformation of internally oxidized Al2O3/Cu composites. The investigation revealed that dispersive alumina can obstruct dislocation sliding and define the subgrain size the...This work concerns with the high temperature deformation of internally oxidized Al2O3/Cu composites. The investigation revealed that dispersive alumina can obstruct dislocation sliding and define the subgrain size thereby improve significantly the strength of the materials at high temperature. The sliding of dislocations is a main deformation mechanism in the given temperature range. The sliding of grain boundary and diffusive creep play important roles at high temperature and low strain rate. The dispersoids can raise the recrystallization temperature to higher than 1223 K. Dynamic recovery is a main softening way under the experimental conditions. Higher deformation rate and lower deformation temperature imply a higher flow stress.展开更多
Silver as a highly conductive metal is usually doped in YBa2Cu3O7-x superconductor bulks to improve critical current density of YBa2Cu3O7-x superconductor.The valuable metal elements silver,yttrium,barium and copper i...Silver as a highly conductive metal is usually doped in YBa2Cu3O7-x superconductor bulks to improve critical current density of YBa2Cu3O7-x superconductor.The valuable metal elements silver,yttrium,barium and copper in waste YBa2Cu3O7-x/Ag composite superconductor bulks were recovered,respectively.Silver was recovered with process at first,the waste was dissolved by nitric acid and silver chloride was precipitated by adding chloride acid,then silver pig was obtained by melting silver chloride together with sodium carbonate at 1 000℃.The effective factors on recovery ratio and purity of silver were studied.The chemical analysis proves that the purity of silver ingot is 95.86%.The recovery ratio of silver is calculated to be 92.56%.The loss of silver may be due to the loss of silver chloride during filtering and the volatilization of silver when silver chloride and sodium carbonate are smelted at high temperature.For other three metal elements,Y3 +,Ba 2+and Cu 2+,in the surplus waste liquid after recovering silver, they were separated with the sequence of barium,copper and then yttrium step by step.First,sulfate acid was used to precipitate barium sulfate.Then,sodium sulfide was added to the surplus solution so that copper could be separated as copper sulfide.During this separation procedure,it was important to control the pH value to be 1-2.After that,oxalic acid was added into the surplus solution to obtain yttrium oxalate.Finally,yttrium oxide was formed by burning yttrium oxalate.The XRD results indicate that the final products are all single-phase compounds as BaSO4,CuS and Y2O3,respectively.展开更多
TiB_(2p)/Cu composites with high reinforcement content(φ_(p)=50%,58%and 65%)for electronic packaging applications were fabricated by squeeze casting technology.The microstructures and thermo-physical properties of th...TiB_(2p)/Cu composites with high reinforcement content(φ_(p)=50%,58%and 65%)for electronic packaging applications were fabricated by squeeze casting technology.The microstructures and thermo-physical properties of the TiB_(2p)/Cu composites were investigated.The results show that TiB2 particles are homogeneous and distribute uniformly,and the TiB2-Cu interfaces are clean and free-from interfacial reaction products and amorphous layers,the densifications of the TiB_(2p)/Cu composites are higher than 98.2%. The mean linear coefficients of thermal expansion at 20-100℃for TiB_(2p)/Cu composites range from 8.3×10^(-6)to 10.8×10^(-6)/K and decrease with increasing volume fraction of TiB2.The experimental coefficients of thermal expansion agree well with the predicted values based on Turner’s model.The thermal conductivities of TiB_(2p)/Cu composites range from 167.3 to 215.4 W/(m·K),decreasing with increasing volume fraction TiB2.展开更多
An adequate hardness of MoS2/Cu composites has not been achieved if these materials are applied under the extreme wear conditions. Therefore, Me-reinforced MoS2/Cu composites were prepared by powder metallurgy （P/M）...An adequate hardness of MoS2/Cu composites has not been achieved if these materials are applied under the extreme wear conditions. Therefore, Me-reinforced MoS2/Cu composites were prepared by powder metallurgy （P/M） methods. The electrical sliding wear properties in the absence or presence of Mereinforced MoS2/Cu composites were tested by HST-100 high speed electric-tribometer. The hardness, electrical conductivity, density, and microstmcture of MoS2/Cu composites were observed. Me-reinforcement MoS2/Cu composites are of good electrical conductivity, while the hardness of Mo-reinforcedment MoS2/Cu composites is about 33.3% higher than that of MoS2/Cu composites. With the addition of Me, composites show better wear properties under high speed and large electric current due to the improvement of hardness. The effects of current intensity and sliding velocity on the wear properties of the tested materials are complicated, and the wear mechanisms of MoS2/Cu composites are mainly abrasive wear and adhesive wear with arc erosion.展开更多
Cs0.35V2O5 was successfully synthesized as cathode material for lithium secondary battery by the rheological phase reaction method from Cs2CO3 and NH4VO3. The Cs0.35V2O5/Cu composite material was prepared by the displ...Cs0.35V2O5 was successfully synthesized as cathode material for lithium secondary battery by the rheological phase reaction method from Cs2CO3 and NH4VO3. The Cs0.35V2O5/Cu composite material was prepared by the displacement reaction in CuSO4 solution using zinc powder as a reductant. The structure and electrochemical property of the so-prepared powders were characterized by means of XRD （powder X-ray diffraction） and the galvanostatic discharge-charge techniques. The results show that the electrochemical property of Cs0.35V2O5/Cu composite material is significantly improved compared to the bulk Cs0.35V2O5 material. The Cs0.35V2O5/Cu composite material exhibits the first discharge capacity as high as 164.3 mAh.g -1 in the range of 4.2-1.8V at a current rate of 10 mA.g-1 and remains at a stable discharge capacity of about 110 mAh.g-1 within 40 cycles.展开更多
基金National Natural Science Foundation of China (50432020)Henan Innovation Project for University Prominent Re- search Talents (2007KYCX008)+3 种基金Henan Education Department Science and Technology Project (2007430004)Henan Plan Project for College Youth Backbone TeacherHenan University of Science and Technology Major Pre-research Foundation (2005ZD003)Henan University of Science and Technology Personnel Scientific Research Foundation (of023)
文摘Two Al2O3/Cu composites containing 0.24 wt.% Al2O3 and 0.60 wt.% Al2O3 separately are prepared by internal oxidation. Effects of sliding speed and pressure on the frictional characteristics of the composites and copper against brass are investigated and compared. The changes in morphology of the sliding surface and subsurface are examined with scanning electron microscope （SEM） and energy dispersive X-ray spectrum （EDS）. The results show that the wear resistance of the Al2O3/Cu composites is superior to that of copper under the same conditions, Under a given electrical current, the wear rate of Al2O3/Cu composites decreases as the Al2O3-content increases, However, the wear rates of the Al2O3/Cu composites and copper increase as the sliding speed and pressure increase under dry sliding condition. The main wear mechanisms for Al2O3/Cu composites are of abrasion and adhesion; for copper, it is adhesion, although wear by oxidation and electrical erosion can also be observed as the speed and pressure rise.
文摘A heat-resistant dispersion-strengthening nano-Al_2O_3/Cu composite with highstrength and high electric conductivity was fabricated in a multiplex medium. The internaloxidation product, microstructures and properties of the composite, and the process flow weresystematically studied. It is confirmed that this new technique simplifies the process and improvesthe properties of the composite. X-ray analysis indicates that the alumina particles formed duringinternal oxidation consist of a large mount of gamma-Al_2O_3 and a certain amount of theta-Al_2O_3and alpha-Al_2O_3. TEM observation shows that the obtained gamma-Al_2O_3 nano-particles areuniformly distributed in the copper grains; their mean size and space between particles are 7 runand 30 nm, respectively. The main properties of the composite with 50 percent cold deformation areas follows: the electric conductivity is 51 MS/m (87 percent IACS), sigma_b = 628 MPa, and thehardness is HRB86. After annealing at 1273 K, all or most of the above properties remain, and themicrostructures are still dependent on elongated fiber-form grains.
基金Projects(51371099,51501091)supported by the National Natural Science Foundation of China。
文摘The(Cu−10Sn)−Ni−MoS2 composites,prepared by powder metallurgy,were studied for the effects of Ni-coated MoS2 on the microstructure,mechanical properties and lubricating properties.The mechanism of effects of Ni and MoS2 on the properties of composites was analyzed through a comparative experiment by adding Ni and MoS2 separately.The results show that the nickel wrapping around the MoS2 particles decreases the reaction rate of MoS2 with the copper matrix,and greatly improves the bonding of the matrix.The composites with 12 wt.%Ni-coated MoS2(C12)show the optimum performance including the mechanical properties and tribological behaviors.Under oil lubrication conditions,the friction coefficient is 0.0075 with a pressure of 8 MPa and a linear velocity of 0.25 m/s.The average dry friction coefficient,sliding against 40Cr steel disc,is measured to be 0.1769 when the linear velocity and pressure are 0.25 m/s and 4 MPa,respectively.
基金The work was supported by the Foundation of Aerospace Innovation Fund and the National Natural Science Foundation of China(No.90505015)the Foundation of National Key Laboratory for Remanufacturing.
文摘TiC-TiB2-Cu composites were produced by self-propagating high-temperature synthesis combined with pseudo hot isostatic pressing using Ti, B4C and Cu powders. The microstructure and mechanical properties of the composites were investigated. The X-ray diffraction （XRD） and scanning electron microscopy （SEM） results showed that the final products were only TiC, TiB2 and Cu phases. The clubbed TiB2 grains and spheroidal or irregular TiC grains were found in the microstructure of synthesized products. The reaction temperature and grain size of TiB2 and TiC particles decreased with increasing Cu content. The introduction of Cu into the composites resulted in a drastic increase in the relative density and flexual strength, and the maximum values were obtained with the addition of 20 wt pct, while the fracture toughness was the best when Cu content was 40 wt pct.
文摘The preferred internal oxidation of aluminum in Cu Al alloy was used to obtain in situ Al 2O 3/Cu composites. The reinforcement particles were mainly γ Al 2O 3, some θ Al 2O 3 and a little α Al 2O 3. Thermodynamics analyses show that the chemical reactions are 3Cu 2O+2Al=6Cu+Al 2O 3 or 3CuO+2Al=3Cu+Al 2O 3. A related equilibrium diagram was drawn. The experiments and investigation show that the formation rate of Al 2O 3 was controlled by the diffusion of oxygen in matrix.
基金Projects(U1502274,51834009)supported by the National Natural Science Foundation of ChinaProject(2017ZDXM-GY-028)supported by the Key Research and Development Program of Shaanxi,China。
文摘In situ TiB2/Cu composites were fabricated by both solid-liquid(S-L)and liquid-liquid(L-L)reactive spray deposition in combination with cold rolling and annealing.The microstructure and properties of the fabricated TiB2/Cu composites were investigated.The results show that the reactive mode and rolling treatment are the main factors affecting the microstructure and properties of the TiB2/Cu composite.The in situ reaction in the L-L reaction can be carried out more completely.By controlling the rolling and annealing process,the relative density and the properties of the as-deposited composites are optimized.The comprehensive performance of the deformed TiB2/Cu composite prepared by L-L reactive spray deposition(401 MPa and 83.5%IACS)is better than that by S-L reactive spray deposition(520 MPa and 20.2%IACS).
基金supported by the National Natural Science Foundation of China(U1407110)Anhui Province Key Research and Development Plan(JZ2018AKKG0332)。
文摘2-D nanosheet Cu2O doped CuO coating poly m-phenylenediamine and melamine/graphene/carbon fibers composite(CuxO/MPM/GFs)was firstly fabricated by compound electrochemical method.CuxO/MPM/GFs was successfully used to the recovery of iodide(I-)from salt water by lower potential-aided sorption and desorption processes.The potential-aided recovery of I-at CuxO/MPM/GFs was characterized by FE-SEM,XRD,IR,Raman,XPS,UV-vis and electrochemical techniques in detail.The maximal adsorption capacity of 86.82 mg·g^-1 could be obtained with a pseudo-second-order model at 0.8 V for 210 min in pH 5.0,0.1 mol·L^-1 NaCl,and the process accompanied the generation of CuI,CuO and I5-.The I-could be quickly desorbed from the electrode with a transfer of CuI to Cu2O by cycle voltammetry from-1.0 to 0.5 V for 90 cycles in pH 9.0,0.1 mol·L^-1 KNO3.Thus,CuxO/MPM/GFs was renewable in the continuous electrochemical-adsorption-desorption processes.
基金Henan Innovation Project for University Prominent Research Talents (2007KYCX008)Henan Major Science and Technol-ogy Project (0523021500)+1 种基金Henan University of Science and Technology Major Pre-research Foundation (2005ZD003)Henan University of Science and Technology Personnel Scientific Research Foundation
文摘Alumina dispersion strengthened copper composite （nano-Al2O3/Cu composite） was recently emerged as a kind of potentially viable and attractive engineering material for applications requiring high strength, high thermal and electrical conductivities and resistance to softening at elevated temperatures. The nano-Al2O3/Cu composite was produced by internal oxidation. The microstructures of the composite were analyzed by the TEM and its hot deformation behavior was investigated by means of continuous compression tests performed on a Gleeble 1500 thermo-simulator. Making use of the modified algorithm-Levenberg-Marquardt （L-M） algorithm BP neural network, a model for predicting the flow stresses during hot deformation was set up on the base of the experimental data. Results show that the microstructures of the composite are characterized by uniform distribution of nano-Al2O3 particles in Cu-matrix. The sliding of dislocations is the main deformation mechanism. The dynamic recovery is the main softening mode with the flow stress decreasing gently from 500℃ to 850 ~C. The recrystallization of Cu-matrix can be retarded late into as high as 850 ℃, when it happens only partially. The well-trained BP neural network model can accurately describe the influence of the temperature, strain rate, and true strain on the flow stresses, therefore, it can precisely predict the flow stresses of the composite under given deforming conditions and provide a new way to optimize hot deforming process parameters.
文摘A copper matrix composite reinforced by TiB_2 particle was fabricated by reactions of Cu,Ti and B powders.The microstructure and mechanical properties of the in situ composite were investigated.The results showed that the in situ formed TiB_2 particles,which has a size of no larger than 1 μm,exhibits a uniform distribution in the copper matrix.Due to TiB_2 reinforcement,the mechanical properties in terms of Young's modulus and yield and ultimate tensile stress of the in situ TiB_2/Cu composite are improved greatly.In addition,even if the volume fraction of TiB_2 reinforcement are the same,the composite in the present study containing fine TiB_2 particles exhibits much higher properties than that of the composite reinforced with coarse ones.
基金Project(10037273) supported by the Ministry of Knowledge Economy,Korea
文摘The effects of reduction ratio during roll bonding on the microstructural evolution at interface and subsequent mechanical properties of roll-bonded Al/Cu 2-ply sheets were investigated. The interface microstructures for several Al/Cu 2-ply sheets fabricated under different reduction ratios between 30% and 65% were verified by transmission electron microscopy(TEM). Taking the difference of interface microstructure into consideration, 3-point bending and peel tests were performed for obtaining flexural and bonding strengths for Al/Cu 2-ply sheets. The effect of the quantified areas of metallurgical bonding at interfaces on the bonding strength was also discussed. The results show that both the bonding and flexural strengths for Al/Cu 2-ply sheets are reduced by decreasing the reduction ratio during the roll bonding process, which is strongly correlated with the interface microstructure. This was especially verified by observing the interface delamination from the 3-point bent samples.
基金The work was financiaIly supported hy the NaturalScience Foundation of Hebei Province (No.94087) alld Pd-ucation Conlmittee of
文摘This work concerns with the high temperature deformation of internally oxidized Al2O3/Cu composites. The investigation revealed that dispersive alumina can obstruct dislocation sliding and define the subgrain size thereby improve significantly the strength of the materials at high temperature. The sliding of dislocations is a main deformation mechanism in the given temperature range. The sliding of grain boundary and diffusive creep play important roles at high temperature and low strain rate. The dispersoids can raise the recrystallization temperature to higher than 1223 K. Dynamic recovery is a main softening way under the experimental conditions. Higher deformation rate and lower deformation temperature imply a higher flow stress.
基金Project(50702012)supported by the National Natural Science Foundation of ChinaProject(20060145030)supported by Doctoral Foundation of Chinese Education Ministry
文摘Silver as a highly conductive metal is usually doped in YBa2Cu3O7-x superconductor bulks to improve critical current density of YBa2Cu3O7-x superconductor.The valuable metal elements silver,yttrium,barium and copper in waste YBa2Cu3O7-x/Ag composite superconductor bulks were recovered,respectively.Silver was recovered with process at first,the waste was dissolved by nitric acid and silver chloride was precipitated by adding chloride acid,then silver pig was obtained by melting silver chloride together with sodium carbonate at 1 000℃.The effective factors on recovery ratio and purity of silver were studied.The chemical analysis proves that the purity of silver ingot is 95.86%.The recovery ratio of silver is calculated to be 92.56%.The loss of silver may be due to the loss of silver chloride during filtering and the volatilization of silver when silver chloride and sodium carbonate are smelted at high temperature.For other three metal elements,Y3 +,Ba 2+and Cu 2+,in the surplus waste liquid after recovering silver, they were separated with the sequence of barium,copper and then yttrium step by step.First,sulfate acid was used to precipitate barium sulfate.Then,sodium sulfide was added to the surplus solution so that copper could be separated as copper sulfide.During this separation procedure,it was important to control the pH value to be 1-2.After that,oxalic acid was added into the surplus solution to obtain yttrium oxalate.Finally,yttrium oxide was formed by burning yttrium oxalate.The XRD results indicate that the final products are all single-phase compounds as BaSO4,CuS and Y2O3,respectively.
基金Project(20080430895)supported by China Postdoctoral Science FoundationProject(2008RFQXG045)supported by the Special Fund of Technological Innovation of Harbin,China。
文摘TiB_(2p)/Cu composites with high reinforcement content(φ_(p)=50%,58%and 65%)for electronic packaging applications were fabricated by squeeze casting technology.The microstructures and thermo-physical properties of the TiB_(2p)/Cu composites were investigated.The results show that TiB2 particles are homogeneous and distribute uniformly,and the TiB2-Cu interfaces are clean and free-from interfacial reaction products and amorphous layers,the densifications of the TiB_(2p)/Cu composites are higher than 98.2%. The mean linear coefficients of thermal expansion at 20-100℃for TiB_(2p)/Cu composites range from 8.3×10^(-6)to 10.8×10^(-6)/K and decrease with increasing volume fraction of TiB2.The experimental coefficients of thermal expansion agree well with the predicted values based on Turner’s model.The thermal conductivities of TiB_(2p)/Cu composites range from 167.3 to 215.4 W/(m·K),decreasing with increasing volume fraction TiB2.
基金Funded by the National Natural Science Foundation of China(No:51371077)Non-ferrous Metal Generic Technology of Henan Collaborative Innovation Center
文摘An adequate hardness of MoS2/Cu composites has not been achieved if these materials are applied under the extreme wear conditions. Therefore, Me-reinforced MoS2/Cu composites were prepared by powder metallurgy （P/M） methods. The electrical sliding wear properties in the absence or presence of Mereinforced MoS2/Cu composites were tested by HST-100 high speed electric-tribometer. The hardness, electrical conductivity, density, and microstmcture of MoS2/Cu composites were observed. Me-reinforcement MoS2/Cu composites are of good electrical conductivity, while the hardness of Mo-reinforcedment MoS2/Cu composites is about 33.3% higher than that of MoS2/Cu composites. With the addition of Me, composites show better wear properties under high speed and large electric current due to the improvement of hardness. The effects of current intensity and sliding velocity on the wear properties of the tested materials are complicated, and the wear mechanisms of MoS2/Cu composites are mainly abrasive wear and adhesive wear with arc erosion.
文摘Cs0.35V2O5 was successfully synthesized as cathode material for lithium secondary battery by the rheological phase reaction method from Cs2CO3 and NH4VO3. The Cs0.35V2O5/Cu composite material was prepared by the displacement reaction in CuSO4 solution using zinc powder as a reductant. The structure and electrochemical property of the so-prepared powders were characterized by means of XRD （powder X-ray diffraction） and the galvanostatic discharge-charge techniques. The results show that the electrochemical property of Cs0.35V2O5/Cu composite material is significantly improved compared to the bulk Cs0.35V2O5 material. The Cs0.35V2O5/Cu composite material exhibits the first discharge capacity as high as 164.3 mAh.g -1 in the range of 4.2-1.8V at a current rate of 10 mA.g-1 and remains at a stable discharge capacity of about 110 mAh.g-1 within 40 cycles.
