Application of Three Order Cumulants in Fault Diagnosis

The three-order cumulants’ complex forms of different definitions include different coupling information of signals, and the information can be used to diagnose fault. In the experiment of pressure reducing valve’s fault diagnosis, through these different coupling information, the features of fault signals and normal signals were extracted by wavelet in different directions, then these features were inputted to diagnose the fault. The experiment shows that this method can achieve a satisfactory result.

Recognition Analysis and Simulation Implementation Based on High-Order Cumulants of Wireless Digital Modulation Mode

This paper mainly studies the data characteristics of high order cumulants using digitally modulated signals, and constructs the identification feature parameters that can distinguish the signal modulation type by the high-order cumulants data of the digital modulation signal. Set the identification signal modulation type determination threshold based on the value of the identification feature parameter. The identification feature parameter value of the signal modulation type is compared with the set determination threshold, to realize the recognition of digital modulation signal. This identification method is implemented based on MATLAB design, with a 2ASK (2-ary Amplitude Shift Keying) signal, 4ASK (4-ary Amplitude Shift Keying) signal, 2PSK (2-ary Phase Shift Keying) signal, 4PSK (4-ary Phase Shift Keying) signal, 2FSK (2-ary Frequency Shift Keying) signal, 4FSK (4-ary Frequency Shift Keying) signal. The second, fourth and sixth order cumulants of the six signals were analyzed. Calculate the selected identification feature parameter value and the determination threshold to identify the six signals. The six signals have made MATLAB identification simulation. Simulation results show that this method is feasible and has high recognition rate. Simulation results verify that such recognition methods maintain a high recognition rate under conditions with low signal-to-noise ratio. This identification method can be extended to more MASK (M-ary Amplitude Shift Keying), MPSK (M-ary Phase Shift Keying), MFSK (M-ary Frequency Shift Keying), MQAM (M-ary Quadrature Amplitude Modulation) signal identification.

THE FOURTH-ORDER CUMULANTS BASED SPECTRALESTIMATION METHOD AND ITS APPLICATIONTO DIRECTION-FINDING

Traditional approaches of spatial spectral estimation are usually based on the second-order statistics. The higher-order cumulants and the poly-spectrum contain more information and are capable of reducing the Gaussian noise. In this paper, we present a new spectrum estimation method for direction-finding, the FOMUSIC algorithm, which is based on the eigen-structure analysis of the fourth-order cumulants. The derivation of the algorithm is given in detail and its performance is illustrated by both the computer simulations and the experiments of a direction-finding system. The obtained results demonstrate that the fourth-order cumulants based method outperforms the traditional methods, especially when the noise is an unknown colored one.

Signal Classification Method Based on Support Vector Machine and High-Order Cumulants

In this paper, a classification method based on Support Vector Machine (SVM) is given in the digital modulation signal classification. The second, fourth and sixth order cumulants of the received signals are used as classification vectors firstly, then the kernel thought is used to map the feature vector to the high dimensional feature space and the optimum separating hyperplane is constructed in space to realize signal recognition. In order to build an effective and robust SVM classifier, the radial basis kernel function is selected, one against one or one against rest of multi-class classifier is designed, and method of parameter selection using cross- validation grid is adopted. Through the experiments it can be concluded that the classifier based on SVM has high performance and is more robust.

The Application of Coupled Three Order Cumulants’ Differential Feature in Fault Diagnosis

Complex three-order cumulant has different definition forms. Different forms conclude different information. For studying the effection of frequency in the coupled signals to fault diagnosis, the differential method to the three order cumulants of coupled signals is adopted. By using the differential of complex three order cumulants before and after respectively, then their ?dimensional spectrum is calculated, and the results are used to fault diagnosis. The experimental results show that, the increase frequency item in three order cumulants after differentiated impacts on the results of fault diagnosis and the degree of effection is relative to the differential times. And the correct rate of fault diagnosis can be raised by changing the differential times of three order cumulants.

Moments and Cumulants of Diffraction Profiles Broadened by Stacking Faults

Line broadening in a diffraction intensity profile of powdered crystalline materials due to stacking fault has been characterized in terms of the zeroth, first, second, third, and fourth moments and the fourth cumulant. Calculations have been derived showing that the first moment causes a shift in the peak position of the profile while the third moment affects its shape. The intensity expression has been derived on the basis of usual Cartesian coordinates and also of polar coordinates indicated by the probability of the fault and the reciprocal lattice parameter as the two axes. The expressions for the fourth cumulant have also been so derived. Here we have used three different approaches to determine methods for calculating the fourth cumulant due to stacking faults. The three forms of the equations derived here are for different coordinate systems, but will arrive at the same answers.

The Application of Cumulants Slices in Fault Diagnosis

Complex third-order cumulant has different definition forms. Different forms have different coupling properties, and the generated complex cumulants slices contain different coupling information of signals. In experiments, using the different definitions, the same coupling method is applied to both specific fault signals and normal signals. Furthermore, complex third-order cumulant slices spectrum is defined, and it is used to analyse the coupling features of normal signals and fault signals. Experiments indicate that the detection accuracy rate on the same fault is not the same with the different coupling method, thus, it provides an alternative method to diagnose the specific fault.

The Application of Three Order Cumulants Coupling Features in Fault Diagnosis

Although mechanical vibration is extremely complicated, each fault signal produced by it has its own inherent features, The distinction may be most prominent between the certain components hidden in those features and the same components of normal signals. Three-order cumulant can reduce the Gaussian background noise automatically and its complex formal includes different coupling information of its signal. In the experiment, through these different coupling modes, the same coupling components are fetched from specific fault signal and normal signal, then these components are used to diagnose that certain fault. The results show that the method can fetch the most prominent distinction between normal signal and the specific fault signal, so the specific fault diagnosis by this method is satisfactory.

Fixed point behavior of cumulants in the three-dimensional Ising universality class

High-order cumulants and factorial cumulants of conserved charges are suggested for the study of the critical dynamics in heavy-ion collision experiments. In this paper, using the parametric representation of the threedimensional Ising model which is believed to belong to the same universality class as quantum chromo-dynamics,the temperature dependence of the second-to fourth-order(factorial) cumulants of the order parameter is studied. It is found that the values of the normalized cumulants are independent of the external magnetic field at the critical temperature, which results in a fixed point in the temperature dependence of the normalized cumulants. In finite-size systems simulated using the Monte Carlo method, this fixed point behavior still exists at temperatures near the critical. This fixed point behavior has also appeared in the temperature dependence of normalized factorial cumulants from at least the fourth order. With a mapping from the Ising model to QCD, the fixed point behavior is also found in the energy dependence of the normalized cumulants(or fourth-order factorial cumulants) along different freezeout curves.

Second-order cumulants ghost imaging

Ghost imaging(GI)is a technique to retrieve images by correlating intensity fluctuations.In this Letter,we present a novel scheme for GI referred to as second-order cumulants GI(SCGI).The image is retrieved from fluctuation information,and resolution may be enhanced compared to traditional GI.We experimentally performed SCGI image reconstruction,and the results are in agreement with theoretical predictions.

Mechanical responses of anchoring structure under triaxial cyclic loading

Dynamic load on anchoring structures(AS)within deep roadways can result in cumulative damage and failure.This study develops an experimental device designed to test AS under triaxial loads.The device enables the investigation of the mechanical response,failure mode,instability assessment criteria,and anchorage effect of AS subjected to combined cyclic dynamic-static triaxial stress paths.The results show that the peak bearing strength is positively correlated with the anchoring matrix strength,anchorage length,and edgewise compressive strength.The bearing capacity decreases significantly when the anchorage direction is severely inclined.The free face failure modes are typically transverse cracking,concave fracturing,V-shaped slipping and detachment,and spallation detachment.Besides,when the anchoring matrix strength and the anchorage length decrease while the edgewise compressive strength,loading rate,and anchorage inclination angle increase,the failure intensity rises.Instability is determined by a negative tangent modulus of the displacement-strength curve or the continued deformation increase against the general downward trend.Under cyclic loads,the driving force that breaks the rock mass along the normal vector and the rigidity of the AS are the two factors that determine roadway stability.Finally,a control measure for surrounding rock stability is proposed to reduce the internal driving force via a pressure relief method and improve the rigidity of the AS by full-length anchorage and grouting modification.

Fatigue Crack Propagation Law of Corroded Steel Box Girders in Long Span Bridges

In order to investigate the fatigue performance of orthotropic anisotropic steel bridge decks,this study realizes the simulation of the welding process through elastic-plastic finite element theory,thermal-structural sequential coupling,and the birth-death element method.The simulated welding residual stresses are introduced into the multiscale finite element model of the bridge as the initial stress.Furthermore,the study explores the impact of residual stress on crack propagation in the fatigue-vulnerable components of the corroded steel box girder.The results indicate that fatigue cracks at the weld toe of the top deck,the weld root of the top deck,and the opening of the transverse diaphragm will not propagate under the action of a standard vehicle load.However,the inclusion of residual stress leads to the propagation of these cracks.When considering residual stress,the fatigue crack propagation paths at the weld toe of the transverse diaphragm and the U-rib weld toe align with those observed in actual bridges.In the absence of residual stress,the cracks at the toe of the transverse diaphragm with a 15%mass loss rate are categorized as type I cracks.Conversely,when residual stress is considered,these cracks become I-II composite cracks.Residual stress significantly alters the cumulative energy release rate of the three fracturemodes.Therefore,incorporating the influence of residual stress is essential when assessing the fatigue performance of corroded steel box girders in long-span bridges.

Spatiotemporal changes of gross primary productivity and its response to drought in the Mongolian Plateau under climate change

Gross primary productivity(GPP)of vegetation is an important constituent of the terrestrial carbon sinks and is significantly influenced by drought.Understanding the impact of droughts on different types of vegetation GPP provides insight into the spatiotemporal variation of terrestrial carbon sinks,aiding efforts to mitigate the detrimental effects of climate change.In this study,we utilized the precipitation and temperature data from the Climatic Research Unit,the standardized precipitation evapotranspiration index(SPEI),the standardized precipitation index(SPI),and the simulated vegetation GPP using the eddy covariance-light use efficiency(EC-LUE)model to analyze the spatiotemporal change of GPP and its response to different drought indices in the Mongolian Plateau during 1982-2018.The main findings indicated that vegetation GPP decreased in 50.53% of the plateau,mainly in its northern and northeastern parts,while it increased in the remaining 49.47%area.Specifically,meadow steppe(78.92%)and deciduous forest(79.46%)witnessed a significant decrease in vegetation GPP,while alpine steppe(75.08%),cropland(76.27%),and sandy vegetation(87.88%)recovered well.Warming aridification areas accounted for 71.39% of the affected areas,while 28.53% of the areas underwent severe aridification,mainly located in the south and central regions.Notably,the warming aridification areas of desert steppe(92.68%)and sandy vegetation(90.24%)were significant.Climate warming was found to amplify the sensitivity of coniferous forest,deciduous forest,meadow steppe,and alpine steppe GPP to drought.Additionally,the drought sensitivity of vegetation GPP in the Mongolian Plateau gradually decreased as altitude increased.The cumulative effect of drought on vegetation GPP persisted for 3.00-8.00 months.The findings of this study will improve the understanding of how drought influences vegetation in arid and semi-arid areas.

Cumulative effects of excess high-normal alanine aminotransferase levels in relation to new-onset metabolic dysfunction-associated fatty liver disease in China

BACKGROUND Within the normal range,elevated alanine aminotransferase(ALT)levels are associated with an increased risk of metabolic dysfunction-associated fatty liver disease(MAFLD).AIM To investigate the associations between repeated high-normal ALT measurements and the risk of new-onset MAFLD prospectively.METHODS A cohort of 3553 participants followed for four consecutive health examinations over 4 years was selected.The incidence rate,cumulative times,and equally and unequally weighted cumulative effects of excess high-normal ALT levels(ehALT)were measured.Cox proportional hazards regression was used to analyse the association between the cumulative effects of ehALT and the risk of new-onset MAFLD.RESULTS A total of 83.13%of participants with MAFLD had normal ALT levels.The incidence rate of MAFLD showed a linear increasing trend in the cumulative ehALT group.Compared with those in the low-normal ALT group,the multivariate adjusted hazard ratios of the equally and unequally weighted cumulative effects of ehALT were 1.651[95%confidence interval(CI):1.199-2.273]and 1.535(95%CI:1.119-2.106)in the third quartile and 1.616(95%CI:1.162-2.246)and 1.580(95%CI:1.155-2.162)in the fourth quartile,respectively.CONCLUSION Most participants with MAFLD had normal ALT levels.Long-term high-normal ALT levels were associated with a cumulative increased risk of new-onset MAFLD.

Effect of non-uniform efficiency on higher-order cumulants in heavy-ion collisions

We perform a systematic study on the effect of non-uniform track efficiency correction in higher-order cumulant analysis in heavy-ion collisions.Through analytical derivation,we find that the true values of cumulants can be successfully reproduced by the efficiency correction with an average of the realistic detector efficiency for particles with the same charges within each single phase space.The theoretical conclusions are supported by a toy model simulation by tuning the non-uniformity of the efficiency employed in the track-by-track efficiency correction method.The valid averaged efficiency is found to suppress the statistical uncertainties of the reproduced cumulants dramatically.Thus,usage of the averaged efficiency requires a careful study of phase space dependence.This study is important for carrying out precision measurements of higher-order cumulants in heavy-ion collision experiments at present and in future.

Joint frequency, 2D AOA and polarization estimation using fourth-order cumulants

Based on fourth-order cumulant and ESPRIT algorithm, a novel joint frequency, two-dimensional angle of arrival (2D AOA) and the polarization estimation method of incoming multiple independent spatial narrow-band non-Gaussian signals in arbitrary Gaussian noise environment are proposed . The array is composed of crossed dipoles parallel to the coordinate axes. The crossed dipole positions are arbitrarily distributed. Computer simulation confirms its feasibility.

SOFFLFM:Super-resolution optical fluctuation Fourierlight-field microscopy

Fourier light-field microscopy(FLFM)uses a microlens aray(MLA)to segment the Fourierplane of the microscopic objective lens to generate multiple two-dimensional perspective views,thereby reconstructing the threedimensional(3D)structure of the sample using 3D deconvo-lution calculation without scanning.However,the resolution of FLFM is stil limited by dif-fraction,and furthermore,it is dependent on the aperture division.In order to improve itsresolution,a super-resolution opticai fuctuation Fourier light-field microscopy(SOFFLFM)wasproposed here,in which the super-resolution optical fluctuation imaging(SOFI)with the abilityof super-resolution was introduced into FLFM.SOFFLFM uses higher-order cumulants statis-tical analysis on an image sequence collected by FLFM,and then carries out 3D deconvolutioncalculation to reconstruct the 3D structure of the sample.The theoretical basis of SOFFLFM onimproving resolution was explained and then verified with the simulations.Simulation resultsdemonstrated that SOFFLFM improved the lateral and axial resolution by more than V2 and 2times in the second-and fourth-order accumulations,compared with that of FLFM.

Ecological risk assessment and early warning of heavy metal cumulation in the soils near the Luanchuan molybdenum polymetallic mine concentration area,Henan Province,central China

The Luanchuan molybdenum polymetallic mine concentration area is rich in mineral resources and has a long history of mining.The environmental impact of long-term mining activities cannot be ignored.It is of great significance to study the ecological risk and the accumulation trends of heavy metals in the soil of mining areas for scientific prevention and control of heavy metal pollution.Taking the Taowanbeigou River Basin in the mine concentration area as the research object,the ecological pollution risk and cumulative effect of heavy metals in the soil of the basin were studied by using the comprehensive pollution index method,potential ecological risk assessment method and geoaccumulation index method.On this basis,the cumulative exceeding years of specific heavy metals were predicted by using the early warning model.The comprehensive potential ecological risk of heavy metals in the soil near the Luanchuan mine concentration area is moderate,and the single element Cd is the main ecological risk factor,with a contribution rate of 53.6%.The overall cumulative degrees of Cu and Pb in the soil are“none-moderate”,Zn and Cd are moderate,Mo has reached an extremely strong cumulative level,Hg,As and Cr risks are not obvious,and the overall cumulative risks order is Mo>Cd>Zn>Cu>Pb>Hg.According to the current accumulation rate and taking the risk screening values for soil contamination of agricultural land as the reference standard,the locations over standard rates of Cu,Zn and Cd will exceed 78%in 90years,and the over standard rate of Pb will reach approximately 57%in 200 years.The cumulative exceeding standard periods of As,Cr and Hg are generally long,which basically indicates that these elements do not pose a significant potential threat to the ecological environment.Mining activities will accelerate the accumulation of heavy metals in soil.With the continuous development of mining activities,the potential pollution risk of heavy metals in the soil of mining areas will also increase.

Rational screening of metal coating on Zn anode for ultrahigh-cumulative-capacity aqueous zinc metal batteries

Aqueous zinc metal batteries feature intrinsic safety,but suffer from severe dendrite growth and water-derived side reactions.Many metal coatings have been explored for stabilizing Zn metal anode via a trialand-error approach.Here,we propose an exercisable way to screen the potential metal coating on Zn anodes in view of de-polarization effect and dendrite-suppressing ability theoretically.As an output of this screening,cadmium(Cd) metal is checked experimentally.Therefore,symmetric ZnllZn cells using Cd coated Zn(Zn@Cd) exhibit an ultra-long cycle life of 3500 h(nearly 5 months) at a high current density of 10 mA cm^(-2),achieving a record-high cumulative capacity(35 A h cm^(-2)) compared to the previous reports.The full cells of Zn@Cd‖MnO_(2) display a markedly improved cycling performance under harsh conditions including a limited Zn supply(N/P ratio=1.7) and a high areal capacity(3.5 mA h cm^(-2)).The significance of this work lies in not only the first report of Cd coating for stabilizing Zn metal anode,but also a feasible way to screen the promising metal materials for other metal anodes.

Developing Weibull-based diameter distributions for the major coniferous species in Heilongjiang Province,China

Diameter distribution models play an important role in forest inventories,growth prediction,and management.The Weibull probability density function is widely used in forestry.Although a number of methods have been proposed to predict or recover the Weibull distribution,their applicability and predictive performance for the major tree species of China remain to be determined.Trees in sample plots of three even-aged coniferous species(Larix olgensis,Pinus sylvestris and Pinus koraiensis)were measured both in un-thinned and thinned stands to develop parameter prediction models for the Weibull probability density function.Ordinary least squares(OLS)and maximum likelihood regression(MLER),as well as cumulative distribution function regression(CDFR)were used,and their performance compared.The results show that MLER and CDFR were better than OLS in predicting diameter distributions of tree plantations.CDFR produced the best results in terms of fitting statistics.Based on the error statistics calculated for different age groups,CDFR was considered the most suitable method for developing prediction models for Weibull parameters in coniferous plantations.