Dispersion effect on the current voltage characteristic of AlGaN/GaN high electron mobility transistors

The current voltage （IV） characteristics are greatly influenced by the dispersion effects in A1GaN/CaN high electron mobility transistors. The direct current （DC） IV and pulsed IV measurements are performed to give a deep investigation into the dispersion effects, which are mainly related to the trap and self-heating mechanisms. The results show that traps play an important role in the kink effects, and high stress can introduce more traps and defects in the device. With the help of the pulsed IV measurements, the trapping effects and self-heating effects can be separated. The impact of time constants on the dispersion effects is also discussed. In order to achieve an accurate static DC IV measurement, the steady state of the bias points must be considered carefully to avoid the dispersion effects.

Physico−mathematical model of the voltage−current characteristics of light-emitting diodes with quantum wells based on the Sah−Noyce−Shockley recombination mechanism

Herein,a physical and mathematical model of the voltage−current characteristics of a p−n heterostructure with quantum wells(QWs)is prepared using the Sah−Noyce−Shockley(SNS)recombination mechanism to show the SNS recombination rate of the correction function of the distribution of QWs in the space charge region of diode configuration.A comparison of the model voltage−current characteristics(VCCs)with the experimental ones reveals their adequacy.The technological parameters of the structure of the VCC model are determined experimentally using a nondestructive capacitive approach for determining the impurity distribution profile in the active region of the diode structure with a profile depth resolution of up to 10Å.The correction function in the expression of the recombination rate shows the possibility of determining the derivative of the VCCs of structures with QWs with a nonideality factor of up to 4.

Hybrid Multi-Infeed Interaction Factor Calculation Method Considering Voltage Regulation Control Characteristics of Voltage Source Converter

Voltage source converter based high voltage direct current(VSC-HVDC)can participate in voltage regulation by flexible control to help maintain the voltage stability of the power grid.In order to quantitatively evaluate its influence on the voltage interaction between VSC-HVDC and line commutated converter based high voltage direct current(LCC-HVDC),this paper proposes a hybrid multi-infeed interaction factor(HMIIF)calculation method considering the voltage regulation control characteristics of VSC-HVDC.Firstly,for a hybrid multi-infeed high voltage direct current system,an additional equivalent operating admittance matrix is constructed to characterize HVDC equipment characteristics under small disturbance.Secondly,based on the characteristic curve between the reactive power and the voltage of a certain VSC-HVDC project,the additional equivalent operating admittance of VSC-HVDC is derived.The additional equivalent operating admittance matrix calculation method is proposed.Thirdly,the equivalent bus impedance matrix is obtained by modifying the alternating current(AC)system admittance matrix with the additional equivalent operating admittance matrix.On this basis,the HMIIF calculation method based on the equivalent bus impedance ratio is proposed.Finally,the effectiveness of the proposed method is verified in a hybrid dual-infeed high voltage direct current system constructed in Power Systems Computer Aided Design(PSCAD),and the influence of voltage regulation control on HMIIF is analyzed.

Application of a Current and Voltage Mixed Control Mode for the New Fast Control Power Supply at EAST

A feedback control system is needed to restrain plasma vertical displacement in EAST （Experimental Advanced Superconducting Toknmak）. A fast control power supply excites active feedback coils, which produces a magnetic field to control the plasma＇s displacement. With the development of EAST, new demands on the new fast control power supply have led to an enhanced ability of fast response and output current, as well as a new control mode. The structure of cascaded and paralleled H-bridges can meet the demand of extended capacity, and digital control can reMize current and voltage mixed control mode. The validity of the proposed scheme is confirmed by experiments.

Online Learning Control for Harmonics Reduction Based on Current Controlled Voltage Source Power Inverters

Nonlinear loads in the power distribution system cause non-sinusoidal currents and voltages with harmonic components.Shunt active filters(SAF) with current controlled voltage source inverters(CCVSI) are usually used to obtain balanced and sinusoidal source currents by injecting compensation currents.However,CCVSI with traditional controllers have a limited transient and steady state performance.In this paper,we propose an adaptive dynamic programming(ADP) controller with online learning capability to improve transient response and harmonics.The proposed controller works alongside existing proportional integral(PI) controllers to efficiently track the reference currents in the d-q domain.It can generate adaptive control actions to compensate the PI controller.The proposed system was simulated under different nonlinear(three-phase full wave rectifier) load conditions.The performance of the proposed approach was compared with the traditional approach.We have also included the simulation results without connecting the traditional PI control based power inverter for reference comparison.The online learning based ADP controller not only reduced average total harmonic distortion by 18.41%,but also outperformed traditional PI controllers during transients.

Adaptive controller design based on input-output signal selection for voltage source converter high voltage direct current systems to improve power system stability

An input-output signal selection based on Phillips-Heffron model of a parallel high voltage alternative current/high voltage direct current(HVAC/HVDC) power system is presented to study power system stability. It is well known that appropriate coupling of inputs-outputs signals in the multivariable HVDC-HVAC system can improve the performance of designed supplemetary controller. In this work, different analysis techniques are used to measure controllability and observability of electromechanical oscillation mode. Also inputs–outputs interactions are considered and suggestions are drawn to select the best signal pair through the system inputs-outputs. In addition, a supplementary online adaptive controller for nonlinear HVDC to damp low frequency oscillations in a weakly connected system is proposed. The results obtained using MATLAB software show that the best output-input for damping controller design is rotor speed deviation as out put and phase angle of rectifier as in put. Also response of system equipped with adaptive damping controller based on HVDC system has appropriate performance when it is faced with faults and disturbance.

2-D Theoretical Model for Current–Voltage Characteristics in AlGaN/GaN HEMT’s

A threshold-voltage-based 2-D theoretical model for the Current–Voltage characteristics of the AlGaN/GaN high electron mobility transistors (HEMT’s) is developed. The present work proposes an improved charge-control model by employing the Robin boundary condition when introduced the solution of the 2-D Poisson’s equation in the density of charge depleted in the AlGaN layer. The dependence of 2-DEG sheet carrier concentration on the aluminum composition and AlGaN layer thickness has been investigated in detail. Current–voltage characteristics developed from the 2-DEG model in order to take into account the impact of gate lengths. The relation between the kink effect and existing deep centers has also been confirmed by using an electrical approach, which can allow to adjust some of electron transport parameters in order to optimize the output current.

Optical fiber-based power and data delivery system for high voltage electronic current transformer

This paper describes a prototype power delivery system developed for high voltage electronic current transformer （ECT） that uses laser light to transfer power to and communicates with the primary converter. The design is based on optical-to-electrical power converters, solid-state diode lasers and optical fibers. Command signals are transmitted via the same up-fiber used to send power from secondary power supply to primary converter. The upward data transmission is completed during the brief interruption of power delivery without affecting steady power-supply. A simple comparator added to the primary converter can take the command data. Experimental results show that the fibers can provide reliable up-link for data transmission at 200 kb/s from the secondary to the primary converter. Based on the delivery system, the secondary converter can control three auxiliary channels to provide additional information. These monitoring channels are used in a time-multiplexing mode to provide information about the operation temperature, voltage and current at the remote unit for monitoring the ECT. This preventive maintenance or built-in test can increase reliability by giving early warning for necessary maintenance request.

Feasibility and Application Study of Optical Voltage/Current Sensors Using FBG

This paper concludes the case study work on the optical sensor, which is a new method for voltage and current measurement. Fiber Bragg gratings (FBG) have been developed and used for decades in the telecommunication industry. In recent years, FBG sensors have found wide applications in monitoring strain, temperature, voltage and current across all industries. As the process of constructing a robust smart grid, thousands of miles of optical-fibers have been deployed along the power transmission lines for the purpose of power production communication. This paper focuses on using the power optical fiber as voltage/current sensors instead of those copper wired traditional current transformers. By using piezoelectric layers, the optical sensor is able to transform voltage/current magnitude into optical signal, as well as transmit the signal through the optical fiber. The application of using optical fiber will significantly reduce the cost of deploying traditional current transformers all around the power grid. Moreover, the optical sensor is more stable, more accurate and faster, with such characteristics, the smart grid monitoring system could be much better. The application of combining the optical composite low-voltage cable (OPLC) and the optical current sensor in the distribution network for smart distribution monitoring has been analyzed.

Effect of Band Trap Band Current on DCIV Spectrum Peaks at LDD Drain Region in 0.275μm nMOST's

Interface traps generated under hot carrier (HC) stress in LDD nMOST's are monitored by the direct current current voltage (DCIV) measurement technique and charge pumping (CP) technique.The measured and analyzed results show that the D peak in DCIV spectrum,which related to the drain region,is affected by a superfluous drain leakage current.The band trap band tunneling current is dominant of this current.

Energy gap suppression and excess current in TI2Ba2CaCu208 intrinsic Josephson junctions

Intrinsic Josephson junctions in misaligned T12Ba2CaCu208 thin film were fabricated on LaA103 substrate. The temperature dependence of the critical current is investigated around liquid nitrogen temperature. In the current voltage characteristic, large voltage jump and lack of resistive branch are observed, which shows good consistency with the intrinsic Josephson junctions. By analyzing the large gap voltage in the curve, great suppression of the energy gap is found. Through discussing the temperature dependence of the gap voltage in liquid nitrogen temperature, it is shown that this phenomenon can be caused by the non-equilibrium quasiparticle injection. The temperature influence on the excess current also confirms the non-equilibrium effect.

Power Voltage Characteristics of Fabricated DSSC Incorporating Multiple Organic Dyes as Photosensitizer

Two sets of Organic dyes were developed using kassod and senna plant leaves. The first sets of dyes are the organic dye from the leaves of two plants while the second set is the dye produce after combining together the dyes from the kassod and senna plants leaves. The two sets of dyes were used to sensitize the grown films. The films were characterized and the current voltage values of the grown films were obtained. The solar simulation result of the grown film for Kassod dyed TiO2 film was recorded for single dyes and for the combination of the two dyes. The result also covers absorbance of the spectra lines, absorbance coefficient values of the dyed TiO2, as well as transmittance and energy band gap values of the developed films. The precursors of tin (IV) chloride (SnCl4) (60%) and hydrofluoric acid (40%) was deposited on the cleaned soda-lime glass using the chemical vapour deposition method and nitrogen gas was supplied as a carrier gas through the bubbler to form the FTO layer. Titanium dioxide paste (TiO2) was deposited using a screen printing method to form M-TiO2.

IC Implementation of a Programmable CMOS Voltage Reference

A new approach for the design and implementation of a programmable voltage reference based on an improved current mode bandgap voltage reference is presented. The circuit is simulated and fabricated with Chartered 0. 35μm mixed-signal technology. Measurements demonstrate that the temperature coefficient is ± 36. 3ppm/℃ from 0 to 100℃ when the VID inputs are 11110.As the supply voltage is varied from 2.7 to 5V, the voltage reference varies by about 5mV. The maximum glitch of the transient response is about 20mV at 125kHz. Depending on the state of the five VID inputs,an output voltage between 1.1 and 1.85V is programmed in increments of 25mV.

Energy gap suppression and excess current in Tl_2Ba_2CaCu_2O_8 intrinsic Josephson junctions

Intrinsic Josephson junctions in misaligned Tl2Ba2CaCu2O8 thin film were fabricated on LaAlO3 substrate. The temperature dependence of the critical current is investigated around liquid nitrogen temperature. In the current voltage characteristic, large voltage jump and lack of resistive branch are observed, which shows good consistency with the intrinsic Josephson junctions. By analyzing the large gap voltage in the curve, great suppression of the energy gap is found. Through discussing the temperature dependence of the gap voltage in liquid nitrogen temperature, it is shown that this phenomenon can be caused by the non-equilibrium quasiparticle injection. The temperature influence on the excess current also confirms the non-equilibrium effect.

Analysis of rail potential and stray current in MVDC railway electrification system

In contrast to the conventional direct current railway electrification system(DC-RES),the medium voltage direct current(MVDC)-RES is considered promising for long-distance high-speed corridors.In the MVDC-RES,traction substations(TSSs)are placed much farther and train loads are much heavier than in the conventional DC-RES.Hence,the MVDC-RES brings a drastic change in catenary voltage,TSS spacing,and train loading,which affects rail potential and stray current.In this connection,this work performs some significant quantitative analysis of rail potential and stray current in the MVDC-RES environment.An MVDC simulation model is proposed and different grounding schemes are analyzed for a single-train and two TSSs scenario as well as for a multi-train multi-TSS scenario.According to the simulation and analysis,the maximum values of rail potential and stray current at MVDC-RES distances and the maximum safe distance between adjacent TSSs are determined.

Residual current compensation for single-phase grounding fault in coal mine power network

The way of neutral point to earth via full compensation arc suppression coil can solve the problem of residual current compensation in coal mine power network effectively. Based on the analysis on the grounding current detection results of Xieqiao coal mine, the conclusion that harmonic component of grounding current is dominated by higher harmonics with complex harmonic sources in coal mine power network system was obtained. The influences of harmonic source type and fault point position on harmonic voltage and harmonic current were analyzed theoretically. The influences of earthed fault feeder detection result and the estimation errors of parameters to earth on residual current compensation were analyzed. A new thought of residual current prediction and the selections of model method and control method were proposed on this basis. The simulation results prove that harmonic amplitudes of zero sequence voltage and zero sequence current are determined by harmonic source type as well as fault point position in coal mine power network, and also prove that zero sequence voltage detection can avoid the unstable problem of coal mine power network system caused by undercompensation of capacitive current. Finally, the experimental device of full compensation arc suppression coil is introduced.

A Fault Current Limiting Hybrid DC Circuit Breaker

Due to the low impedance characteristic of the high voltage direct current(HVDC)grid,the fault current rises extremely fast after a DC-side fault occurs,and this phenomenon seriously endangers the safety of the HVDC grid.In order to suppress the rising speed of the fault current and reduce the current interruption requirements of the main breaker(MB),a fault current limiting hybrid DC circuit breaker(FCL-HCB)has been proposed in this paper,and it has the capability of bidirectional fault current limiting and fault current interruption.After the occurrence of the overcurrent in the HVDC grid,the current limiting circuit(CLC)of FCL-HCB is put into operation immediately,and whether the protected line is cut off or resumed to normal operation is decided according to the fault detection result.Compared with the traditional hybrid DC circuit breaker(HCB),the required number of semiconductor switches and the peak value of fault current after fault occurs are greatly reduced by adopting the proposed device.Extensive simulations also verify the effectiveness of the proposed FCL-HCB.

New Generation of Outdoor Vacuum Circuit Breakers with Rated Voltage up to 40.5 kV

The article describes design peculiarities of the novel compact vacuum circuit breaker with rated voltage 40.5 kV. The design incorporates several novel technical solutions： polycarbonate support insulation, mono-stable magnetic actuator, labyrinth pulling insulator, core-type flexible contact and new compact vacuum interrupter （VI）. Phases are encapsulated into silicone rubber providing required creepage distance and excellent tracking resistance. These novelties along with extensive modeling of the mechanical and electrical fields followed by design optimization resulted in weight reduction of more than 50% compared with alternatives available in the market. And this is in spite of built in sensors measuring： phase currents, zero-sequence current, phase voltages.

Performance enhancement of CMOS terahertz detector by drain current

In this paper, we study the effect of the drain current on terahertz detection for Si metal-oxide semiconductor fieldeffect transistors（MOSFETs） both theoretically and experimentally. The analytical model, which is based on the smallsignal equivalent circuit of MOSFETs, predicts the significant improvement of the voltage responsivity Rv with the bias current. The experiment on antennas integrated with MOSFETs agrees with the analytical model, but the Rv improvement is accompanied first by a decrease, then an increase of the low-noise equivalent power（NEP） with the applied current. We determine the tradeoff between the low-NEP and high-Rv for the current-biased detectors. As the best-case scenario, we obtained an improvement of about six times in Rv without the cost of a higher NEP. We conclude that the current supply scheme can provide high-quality signal amplification in practical CMOS terahertz detection.

CMOS Realization of VDTA Based Electronically Tunable Wave Active Filter with Minimum Power Consumption at Low Supply Voltage ±0.82 V

This paper presents a higher order voltage and current mode low pass or high pass filter for wave active filter based on Voltage Differencing Transconductance Amplifiers (VDTAs). The wave equivalent variable technique and topological simulation as well as operational realization using wave variables techniques are proposed for basic active building blocks of wave active filters. The proposed wave equivalent technique is employed for wave active filter with the proper selection of the terminal connections. This work presented the basic element for the realizing wave active filter is the series inductor with parallel grounded capacitor. The proposed wave active filter is verified by realizing a 4th order low pass and high pass Butterworth filter with minimum power consumption at ±0.82 V using SPICE simulation with 0.18 μm TSMC CMOS technology parameters.