RELIABLE HYSTERESIS CURRENT CONTROLLED DUAL BUCK HALF BRIDGE INVERTER

A highly efficient and re liable topology-dual buck half bridge inverter (DBI) is introduced. The existenc e of discontinuous conduction mode (DCM) operation state requires the bias of in du ctor current for DBI implemented with linear controllers like ramp comparison SP WM (RCSPWM) controllers. A novel operation scheme for DBI and a hysteresis curre nt controlled dual buck half bridge inverter (HCDBI) are proposed. The bias curr ent required by RCSPWM DBI is eliminated and conduction losses are dramatically reduced. HCDBI has greatly improved the modulation performance in DCM region for the benefit of its excellent command tracking capability. The operational schem e and control strategy are presented. Power losses of the conventional half brid ge inverter (CHBI) and HCDBI are compared with mathematical computation, and exp erimental verification is also executed. Both calculational and experimental res ults verify that HCDBI has a superior switching performance over CHBI. Its exce llent high frequency operational capacity provides another access to realize high fre quency operation of inverters.

Online Learning Control for Harmonics Reduction Based on Current Controlled Voltage Source Power Inverters

Nonlinear loads in the power distribution system cause non-sinusoidal currents and voltages with harmonic components.Shunt active filters(SAF) with current controlled voltage source inverters(CCVSI) are usually used to obtain balanced and sinusoidal source currents by injecting compensation currents.However,CCVSI with traditional controllers have a limited transient and steady state performance.In this paper,we propose an adaptive dynamic programming(ADP) controller with online learning capability to improve transient response and harmonics.The proposed controller works alongside existing proportional integral(PI) controllers to efficiently track the reference currents in the d-q domain.It can generate adaptive control actions to compensate the PI controller.The proposed system was simulated under different nonlinear(three-phase full wave rectifier) load conditions.The performance of the proposed approach was compared with the traditional approach.We have also included the simulation results without connecting the traditional PI control based power inverter for reference comparison.The online learning based ADP controller not only reduced average total harmonic distortion by 18.41%,but also outperformed traditional PI controllers during transients.

Current Controlled Relaxation Oscillations in Ge_2Sb_2Te_5-Based Phase Change Memory Devices

The relaxation oscillation of the phase change memory （PCM） devices based on the Ge2Sb2Te5 material is investigated by applying square current pulses. The current pulses with different amplitudes could be accurately given by the independently designed current testing system. The relaxation oscillation across the PCM device could be measured using an oscilloscope. The oscillation duration decreases with time, showing an inner link with the shrinking threshold voltage Vth. However, the relaxation oscillation would not terminate until the remaining voltage Von reaches the holding voltage Vh. This demonstrates that the relaxation oscillation might be controlled by Von. The increasing current amplitudes could only quicken the oscillation velocity but not be able to eliminate it, which indicates that the relaxation oscillation might be an inherent behavior for the PCM cell.

Accurate two-degree-of-freedom discrete-time current controller design for PMSM using complex vectors

Properties of the current controller are essential for permanent magnet synchronous machine(PMSM)drives,but the conventional continuous-time current controller cannot fully decouple the cross-coupling terms when applied in the digital processor.Its performance is related closely to the rotational speed.To improve the performance of the current loop,the direct design method in the discrete-time domain is adopted using the accurate discrete-time complex vector model.An integrated accurate hold-equivalent discrete model for PMSM is derived considering the difference between the output of the voltage source inverter and the back electro-motive force.Then an accurate two-degree-of-freedom(2DOF)current controller with a third-order closed-loop transfer function is designed.The 2DOF controller has more freedom in pole placement,and two schemes with a different cancelled pole-zero pair are investigated.Analysis is conducted by the robust root locus method via the complex vector root locus and sensitivity functions,showing properties in disturbance rejection and sensitivity to parameter variation of two schemes.Both schemes have their own advantages.Finally,the dynamic performance and flexibility of the proposed current controller is verified on a 2.5-kW PMSM test bench.

Effects of current waveform parameters during droplet transfer on spatter in high speed waveform controlled Short-circuiting GMAW

Aim at improving the stability of the Short-circuiting Gas Metal Arc Welding （GMAW-S） process for the enhanced speed usage, effects of current waveform parameters during short-term on the welding stability have been investigated by experimental method. The welding power source used for the research is an inverter with a special current waveform control. It is shown that the spatter decreases at first then increases with each increase of the low current period, current increase rate and the maximum current limit. The test results are provided for welding of 1 mm and 3 mm mild steel at speed of 1.2 m/min. The stable GMA W-S process under high speed welding condition has been achieved by optimizing the parameters.

Effects of controlled pulse current waveform on key-holing condition in plasma arc welding

To overcome the shortcomings of conventional plasma arc welding （ PAW）, the ＇ controlled pulse key-holing＇ strategy is proposed and the keyhole PAW experiment system is developed. ＇The efflux plasma voltage signal is detected in realtime to characterize the keyhole size and dimension. The welding current waveform for controlled pulse key-holing strategy is implemented, and two slow-decreasing slopes are added at the dropping point from peak current to base current to further reduce both heat input and arc force so that the controllability of keyhole dynamics is improved. Two kinds of PAW tests are conducted, anti the different parameters of the controlled pulse current and the relevant efflux plasma voltage are measured in real-time to investigate ihe effects of welding current waveform parameters on the key-holing condition.

An Improved Deadbeat Predictive Current Control Method for SPMSM Drives with a Novel Adaptive Disturbance Observer

To improve the dynamic performance of conventional deadbeat predictive current control(DPCC)under parameter mismatch,especially eliminate the current overshoot and oscillation during torque mutation,it is necessary to enhance the robustness of DPCC against various working conditions.However,the disturbance from parameter mismatch can deteriorate the dynamic performance.To deal with the above problem,firstly,traditional DPCC and the parameter sensitivity of DPCC are introduced and analyzed.Secondly,an extended state observer(ESO)combined with DPCC method is proposed,which can observe and suppress the disturbance due to various parameter mismatch.Thirdly,to improve the accuracy and stability of ESO,an adaptive extended state observer(AESO)using fuzzy controller based on ESO,is presented,and combined with DPCC method.The improved DPCC-AESO can switch the value of gain coefficients with fuzzy control,accelerating the current response speed and avoid the overshoot and oscillation,which improves the robustness and stability performance of SPMSM.Finally,the three methods,as well as conventional DPCC method,DPCC-ESO method,DPCC-AESO method,are comparatively analyzed in this paper.The effectiveness of the proposed two methods are verified by simulation and experimental results.

Design and analysis of dual-mode structure repetitive control based hybrid current regulation scheme for active power filters

An all-digital hybrid current regulation scheme for the single-phase shunt active power filter （APF） is presented. The proposed hybrid current control scheme integrates the deadbeat control and the dual-mode structure repetitive control （DMRC） so that it can offer superior steady-state performance and good transient features. Unlike the conventional schemes, the proposed scheme-based APF can compensate both the odd and the even order harmonics in grid. The detailed design criteria and the stability analysis of the proposed hybrid current controller are presented. Moreover, an improved structure which incorporates the proposed hybrid controller and the resonant controller for tracking specific order harmonics is given. The relationships between the resonant controller and different repetitive control schemes are discussed. Experimental results verify the effectiveness and advantages of the proposed hybrid control scheme.

Design of DSTATCOM Controller for Compensating Unbalances

In a three phase power system, the voltages at the generation side are in sinusoidal and equal in magnitude with 120? phase difference between the phases. However, at the load side voltages may become unbalanced due to unequal voltage magnitudes at the fundamental frequency, phase angle deviations or unequal distribution of single phase loads. The voltage unbalance is a major power quality issue, because a small unbalance in the phase voltages can cause a larger unbalance in the phase currents. A completely balanced three-phase three wire system contains only positive sequence components of voltage, current and impedance, whereas unbalanced system contains both positive and negative sequence components of voltages and currents. The negative sequence component of current in the unbalanced system increases the temperature and losses in the equipments. Hence, it is necessary to mitigate this problem by supplying the negative sequence current to the load at the load side and keep the source side balanced. This paper proposes the shunt connected, current injecting Distribution Static Synchronous Compensator (DSTATCOM) with appropriate controller to mitigate the unbalanced load current. The symmetrical components based Hysteresis Current Controller (HCC) is designed for DSTATCOM to diminish the unbalances in a three-phase three-wire system. The performance of the controller is studied by simulating the entire system in the MATLAB/Simulink environment. The DSTATCOM with HCC is found to be better than other controllers because it is suitable for compensating both balanced and unbalanced loads.

Stationary-frame current control strategy for transverse flux permanent-magnet machine

A new stationary-frame AC current control strategy that can eliminate steady-state errors is discussed and applied to the control of transverse flux permanent-magnet machine （TFPM）. Based on the principle of modulation and demodulation, this AC controller can achieve the same frequency response characteristic as the equivalent DC controller. Validity of the TFPM control system using this current control strategy is confirmed with simulation results.

Model Predictive Current Control with Adaptive-adjusting Timescales for PMSMs

A model predictive current control(MPCC)with adaptive-adjusting method of timescales for permanent magnet synchronous motors(PMSMs)is proposed in this paper to improve the dynamic response and prediction accuracy in transient-state,while lessening the computational burden and improving the control performance in steady-state.The timescale characteristics of different parts of MPCC,such as signal sampling,prediction calculation,control output,model error correction,are analyzed,and the algorithm architecture of MPCC with multi-timescale is proposed.The difference between reference and actual speed,and the change rate of actual speed are utilized to discriminate the transient state of speed change and load change,respectively.Adaptive-adjusting method of control period and prediction stepsize are illustrated in detail after operation condition discrimination.Experimental results of a PMSM are presented to validate the effectiveness of proposed MPCC.In addition,comparative evaluation of single-step MPCC with fixed timescale and proposed MPCC is conducted,which demonstrates the superiority of proposed control strategy.

Application of a Current and Voltage Mixed Control Mode for the New Fast Control Power Supply at EAST

A feedback control system is needed to restrain plasma vertical displacement in EAST （Experimental Advanced Superconducting Toknmak）. A fast control power supply excites active feedback coils, which produces a magnetic field to control the plasma＇s displacement. With the development of EAST, new demands on the new fast control power supply have led to an enhanced ability of fast response and output current, as well as a new control mode. The structure of cascaded and paralleled H-bridges can meet the demand of extended capacity, and digital control can reMize current and voltage mixed control mode. The validity of the proposed scheme is confirmed by experiments.

Energy-Based Current Control for Stabilizing a Flexible Electrodynamic Tether System

An energy-based controller of electric current is synthesized for the libration stabilization of an electrodynamic tether system,which consists of a relatively large main-satellite and a sub-satellite of much smaller size.Two dynamic models with different levels of accuracy are considered in this work.First,a dumbbell model of the system is used for the controller design,which aims at damping injection on the libration motions via the real-time regulation of the electric current.Furthermore,the efficacy and performance of the proposed scheme are numerically verified by using a more complex multi-body model which accounts for not only the tether flexibility but also the attitude of the main-satellite.

Predictive current control system of PMSM based on LADRC

For a permanent magnet synchronous motor(PMSM)model predictive current control(MPCC)system,when the speed loop adopts proportional-integral(PI)control,speed regulation is easily affected by motor parameters,resulting in the inability to balance the system robustness and dynamic performance.A PMSM optimal control strategy combining linear active disturbance rejection control(LADRC)and two-vector MPCC(TV-MPCC)is proposed.Firstly,a mathematical model of a PMSM is presented,and the PMSM TV-MPCC model is developed in the synchronous rotation coordinate system.Secondly,a first-order LADRC controller composed of a linear extended state observer and linear state error feedback is designed to reduce the complexity of parameter tuning while linearly simplifying the traditional active disturbance rejection control(ADRC)structure.Finally,the conventional PI speed regulator in the motor speed control system is replaced by the designed LADRC controller.The simulation results show that the speed control system using LADRC can effectively deal with the changes in motor parameters and has better robustness and dynamic performance than PI control and similar methods.The system has a fast motor speed response,small overshoot,strong anti-interference,and no steady-state error,and the total harmonic distortion is reduced.

Model predictive current control for PMSM driven by three-level inverter based on fractional sliding mode speed observer

Based on the fractional order theory and sliding mode control theory,a model prediction current control(MPCC)strategy based on fractional observer is proposed for the permanent magnet synchronous motor(PMSM)driven by three-level inverter.Compared with the traditional sliding mode speed observer,the observer is very simple and eases to implement.Moreover,the observer reduces the ripple of the motor speed in high frequency range in an efficient way.To reduce the stator current ripple and improve the control performance of the torque and speed,the MPCC strategy is put forward,which can make PMSM MPCC system have better control performance,stronger robustness and good dynamic performance.The simulation results validate the feasibility and effectiveness of the proposed scheme.

Growth and passivation of aluminum etch tunnels at on-off controlling direct current in 6 wt.% HCI solution

Growth and passivation of tunnels within Al foil by on-off controlling DC etching in 6 wt.% HCI solution has been investigated. It was found that, in a given etchant solution at a special temperature, the longest tunnel length was only a function of the turn-on interval of DC. The potential of Al foil broke at on-off controlling DC by the result from anode polarization curves and potential-time （E-t） responding curves. When DC was switched on, the potential increased abruptly over pitting potential, leading to nucleation of pits at the surface and the growth of tunnels at special length. When DC was switched off, the potential decreased rapidly to a passive value, leading to stoppage of nucleation and death of tunnels. By this way, the longest tunnel length can be controlled and a non-piercing layer can be obtained. Hence, etching of Al foil at this current is beneficial for maintaining a good mechanical strength.

Finite Control Set Model Predictive Current Control of a Five-Phase PMSM with Virtual Voltage Vectors and Adaptive Control Set

This paper presents an improved finite control set model predictive current control(FCS-MPCC)of a five-phase permanent magnet synchronous motor(PMSM).First,to avoid including all the 32 voltage vectors provided by a two-level five-phase inverter into the control set,virtual voltage vectors are adopted.As the third current harmonics can be much reduced by virtual voltage vectors automatically,the harmonic items in the cost function of conventional FCS-MPCC are not considered.Furthermore,an adaptive control set is proposed based on voltage prediction.Best control set with proper voltage vector amplitude corresponding to different rotor speed can be achieved by this method.Consequently,current ripples can be largely reduced and the system performs much better.At last,simulations are established to verify the steady and transient performance of the proposed FCS-MPCC,and experiments based on a 2 kW five-phase motor are carried out.The results have validated the performance improvement of the proposed control strategy.

Control Strategies for PM Synchronous Machine Controlled Rectifier Intended for Heavy-Duty Vehicle

In order to charge batteries and supply all the electrical devices like wheel-motors used in a heavy-duty hybrid electric vehicle, a solution consists in using an assembly permanent magnet generator driven by a diesel engine and a three-phase insulated gate bipolar transistor/diodes bridge controlled rectifier connected to the battery. In this work, hysteresis current control strategies combined with a judicious current sensing mode for the assembly permanent magnet synchronous machine-controlled rectifier are investigated. Main issues first concern the different kinds of transistors switching modes allowed by the proposed current sensing mode when the machine operates either as a generator or as a motor. Second, the modulated hysteresis method is presented, which merges the performances of robustness and dynamic of the classical hysteresis method and imposes the switching frequency alike pulsewidth modulation techniques. A test bench at reduced power permits to test the switching modes as well as classical and modulated hysteresis methods for both motor and generator operating modes and to validate the simulation predictions. The digital signal processor algorithm elaborated for the control strategy is flexible and adaptable to all kinds of transistor switchings and machine operating modes.

The Current Status and Challenges Regarding Tuberculosis Infection Control in Health Care Facilities in China

Health care facilities are a high-risk environment for generating and spreading respiratory infectious diseases such as tuberculosis （TB）. The TB prevention and treatment staff in health care facilities are responsible for the identification, diagnosis, treatment, supervision, and management of TB patients .

The Peak Current Control of Permanent Magnet Brushless DC Machine with Asymmetric Dual-Three Phases

The asymmetric dual-three phase BLDC motor has two sets of stator windings,in which the back EMF coefficients are different.This paper takes advantage of the asymmetric dual-three phase BLDC motor’s structural features and proposes a new method for the accelerated problem of the BLDC motor operating in the high speed and the constant electromagnetic power.The dual phase windings of the BLDC motor are integrated into the circuit in the starting stage.When the motor’s back EMF value is equal to the terminal voltage value,switch off a set of RST three phase windingswhose back EMF coefficient is bigger and make the other set of stator windingUVWwith smaller back EMF coefficient continue to operate under the rated power.As the motor rotor speed continues to increase,the electromagnetic torque remains unchanged.By using the peak current control strategy,we can deduce that the phase current of the UVW three-phase winding is twice the RSTthree-phase windingwhen the asymmetric dual-three phase BLDC motor operates at high speed and constant power.