Studies were made of the calculation of fractal dimension of transverse impact fracture sur- face,and of the correlation between impact toughness of steel and parameters of free-cutting phase by means of the developed...Studies were made of the calculation of fractal dimension of transverse impact fracture sur- face,and of the correlation between impact toughness of steel and parameters of free-cutting phase by means of the developed fractal geometry model of crack propagation.It is believed that the area fraction,f,of free-cutting phase is negligibly influential to the longitudinal im- pact toughness,as f1 .While the aspect ratio,saying ratio of length to width,of free-cut. ting phase is inversely influential to the transverse impact toughness.This may .be the reason why the transverse impact toughness of free-cutting steel containing more rare earth contrast to sulphur is even higher than the low sulphur containing steel.展开更多
An advanced ceramic cutting tool material Al2O3/TiC/TiN （LTN） is developed by incorporation and dispersion of micro-scale TiC particle and nano-scale TiN particle in alumina matrix. With the optimal dispersing and f...An advanced ceramic cutting tool material Al2O3/TiC/TiN （LTN） is developed by incorporation and dispersion of micro-scale TiC particle and nano-scale TiN particle in alumina matrix. With the optimal dispersing and fabricating technology, this multi-scale and multi-phase nanocomposite ceramic tool material can get both higher flexural strength and fracture toughness than that of A1203/TiC （LZ） ceramic tool material without nano-scale TiN particle, especially the fracture toughness can reach to 7.8 MPa . m^0.5. The nano-scale TiN can lead to the grain fining effect and promote the sintering process to get a higher density. The coexisting transgranular and intergranular fracture mode induced by micro-scale TiC and nano-scale TiN, and the homogeneous and densified microstructure can result in a remarkable strengthening and toughening effect. The cutting performance and wear mechanisms of the advanced multi-scale and multi-phase nanocomposite ceramic cutting tool are researched.展开更多
The free-cutting phase in RE or Ca-RE treated sulfur-containing free-cutting steel is the eutectic phases of MnS-RE_2S_3 and (Mn,Ca)S-RE_2S_3,respectively.The atomic ratio of RE/S needed to modify all the MnS into the...The free-cutting phase in RE or Ca-RE treated sulfur-containing free-cutting steel is the eutectic phases of MnS-RE_2S_3 and (Mn,Ca)S-RE_2S_3,respectively.The atomic ratio of RE/S needed to modify all the MnS into the eutectic phase is higher than 1.48 or 1.41-1.37 Ca/S,when RE or Ca-RE is used as the modifiz- er in the sulfur-containing free-cutting steel.Moreover,the thermodynamical calculation shows that the eutectic temperature is lower than the solidifying temperature,which is the key condition for the eutectic phase to keep globual during solidifying.展开更多
It has been found that the brittle material, monocrystalline silicon, can be machined in ductile mode in nanoscale cutting when the tool cutting edge radius is reduced to nanoscale and the undeformed chip thickness is...It has been found that the brittle material, monocrystalline silicon, can be machined in ductile mode in nanoscale cutting when the tool cutting edge radius is reduced to nanoscale and the undeformed chip thickness is smaller than the tool edge radius. In order to better understand the mechanism of ductile mode cutting of silicon, the molecular dynamics （MD） method is employed to simulate the nanoscale cutting of monocrystalline silicon. The simulated variation of the cutting forces with the tool cutting edge radius is compared with the cutting force results from experimental cutting tests and they show a good agreement. The results also indicate that there is silicon phase transformation from monocrystalline to amorphous in the chip formation zone that can be used to explain the cause of ductile mode cutting. Moreover, from the simulated stress results, the two necessary conditions of ductile mode cutting, the tool cutting edge radius are reduced to nanoscale and the undeformed chip thickness should be smaller than the tool cutting edge radius, have been explained.展开更多
The generation of high-resolution DEM from interferometric SAR has resulted in the need for accurate and efficient methods of 2-dimensional phase unwrapping. In this paper, we give a brief description of the mathemati...The generation of high-resolution DEM from interferometric SAR has resulted in the need for accurate and efficient methods of 2-dimensional phase unwrapping. In this paper, we give a brief description of the mathematical base of phase unwrapping, and a detailed description of the unweighted and weighted least square phase unwrapping algorithm.Then our algorithm combining with the weighted least square phase unwrapping guided by the branch-cuts derived from Goldstein’ s algorithm and coherence coefficient map derived from the INSAR data is provided. In our experiment we write subroutines of the Goldstein’s branch-cut algorithm,unweighted and weighted least square phase unwrapping algorithm as well as our algorithm,and construct a small experiment system to resolve the phase unwrapping problem. Finally we test our algorithm on some INSAR data. The result shows that our approach can obtain unwrapped phase correctly and efficiently.展开更多
文摘Studies were made of the calculation of fractal dimension of transverse impact fracture sur- face,and of the correlation between impact toughness of steel and parameters of free-cutting phase by means of the developed fractal geometry model of crack propagation.It is believed that the area fraction,f,of free-cutting phase is negligibly influential to the longitudinal im- pact toughness,as f1 .While the aspect ratio,saying ratio of length to width,of free-cut. ting phase is inversely influential to the transverse impact toughness.This may .be the reason why the transverse impact toughness of free-cutting steel containing more rare earth contrast to sulphur is even higher than the low sulphur containing steel.
基金Selected from Proceedings of the 7th International Conference on Frontiers of DesignManufacturing(ICFDM'2006)This project is supported by National Natural Science Foundation of China(No.50275086)the University of New South Wales Visiting Professorship Scheme,Australia.
文摘An advanced ceramic cutting tool material Al2O3/TiC/TiN （LTN） is developed by incorporation and dispersion of micro-scale TiC particle and nano-scale TiN particle in alumina matrix. With the optimal dispersing and fabricating technology, this multi-scale and multi-phase nanocomposite ceramic tool material can get both higher flexural strength and fracture toughness than that of A1203/TiC （LZ） ceramic tool material without nano-scale TiN particle, especially the fracture toughness can reach to 7.8 MPa . m^0.5. The nano-scale TiN can lead to the grain fining effect and promote the sintering process to get a higher density. The coexisting transgranular and intergranular fracture mode induced by micro-scale TiC and nano-scale TiN, and the homogeneous and densified microstructure can result in a remarkable strengthening and toughening effect. The cutting performance and wear mechanisms of the advanced multi-scale and multi-phase nanocomposite ceramic cutting tool are researched.
基金The project supported by the National Natural Science Foundation of China
文摘The free-cutting phase in RE or Ca-RE treated sulfur-containing free-cutting steel is the eutectic phases of MnS-RE_2S_3 and (Mn,Ca)S-RE_2S_3,respectively.The atomic ratio of RE/S needed to modify all the MnS into the eutectic phase is higher than 1.48 or 1.41-1.37 Ca/S,when RE or Ca-RE is used as the modifiz- er in the sulfur-containing free-cutting steel.Moreover,the thermodynamical calculation shows that the eutectic temperature is lower than the solidifying temperature,which is the key condition for the eutectic phase to keep globual during solidifying.
基金Selected from Proceedings of the 7th International Conference on Frontiers of DesignManufacturing(ICFDM'2006).
文摘It has been found that the brittle material, monocrystalline silicon, can be machined in ductile mode in nanoscale cutting when the tool cutting edge radius is reduced to nanoscale and the undeformed chip thickness is smaller than the tool edge radius. In order to better understand the mechanism of ductile mode cutting of silicon, the molecular dynamics （MD） method is employed to simulate the nanoscale cutting of monocrystalline silicon. The simulated variation of the cutting forces with the tool cutting edge radius is compared with the cutting force results from experimental cutting tests and they show a good agreement. The results also indicate that there is silicon phase transformation from monocrystalline to amorphous in the chip formation zone that can be used to explain the cause of ductile mode cutting. Moreover, from the simulated stress results, the two necessary conditions of ductile mode cutting, the tool cutting edge radius are reduced to nanoscale and the undeformed chip thickness should be smaller than the tool cutting edge radius, have been explained.
基金Project supported by the National Natural Science Foundation of China(No.69782001)
文摘The generation of high-resolution DEM from interferometric SAR has resulted in the need for accurate and efficient methods of 2-dimensional phase unwrapping. In this paper, we give a brief description of the mathematical base of phase unwrapping, and a detailed description of the unweighted and weighted least square phase unwrapping algorithm.Then our algorithm combining with the weighted least square phase unwrapping guided by the branch-cuts derived from Goldstein’ s algorithm and coherence coefficient map derived from the INSAR data is provided. In our experiment we write subroutines of the Goldstein’s branch-cut algorithm,unweighted and weighted least square phase unwrapping algorithm as well as our algorithm,and construct a small experiment system to resolve the phase unwrapping problem. Finally we test our algorithm on some INSAR data. The result shows that our approach can obtain unwrapped phase correctly and efficiently.
