Stability control measures for roof cutting and NPR supporting of mining roadways in fault areas of kilometre-deep coal mine

The study focuses on the stability control measures for mining roadways in fault zones of deep mines,using Daqiang Coal Mine as a case study.The control system under consideration,referred to as"pre-splitting cutting roof+NPR anchor cable"(PSCR-NPR),is subjected to scrutiny through theoretical analysis,numerical modelling,and field trials.Furthermore,a comprehensive analysis is undertaken to evaluate the stability control mechanism of this particular technology.The study provides evidence that the utilization of deep-hole directional energy-concentrated blasting facilitates the attainment of directional roof cutting in roadways.The aforementioned procedure leads to the formation of a uniform structural surface on the roof of the roadway and causes modifications in the surrounding geological formation.The examination of the lateral abutment pressure and shear stress distribution,both prior to and subsequent to roof cutting,indicates that the implementation of pre-splitting techniques leads to a noteworthy reduction in pressure.The proposition of incorporating the safety factor Q for roof cutting height is suggested as a method to augment comprehension of the pressure relief phenomenon in the field of engineering.The analysis of numerical simulation has indicated that the optimal pressure relief effect of a mining roadway in a fault area is attained when the value of Q is 1.8.The NPR anchor cable exhibits noteworthy characteristics,including a high level of prestress,continuous resistance,and substantial deformation.After the excavation of the roadway,a notable reduction in radial stress occurs,leading to the reinstatement of the three-phase stress state in the surrounding rock.This restoration is attributed to the substantial prestress exerted on the radial stress.The termination point of the NPR anchor cable is strategically positioned within a stable rock formation,allowing for the utilization of the mechanical characteristics of the deep stable rock mass.This positioning serves to improve the load-bearing capacity of the surrounding rock.The mining roadway within the fault region of Daqiang Coal Mine is outfitted with the PSCR-NPR technology.The drop in shear stress experienced by the rock surrounding the roadway is estimated to be around 30%,whilst the low-stress region of the mining roadway extends by a factor of approximately 5.5.The magnitude of surface displacement convergence experiences a decrease of approximately 45%-50%.The study’s findings provide useful insights regarding the stable of mining roadway in characterized by fault zones.

Instability mechanism of mining roadway passing through fault at different angles in kilometre-deep mine and control measures of roof cutting and NPR cables

The angle α between the fault strike and the axial direction of the roadway produces different damage characteristics. In this paper, the research methodology includes theoretical analyses, numerical simulations and field experiments in the context of the Daqiang coal mine located in Shenyang, China. The stability control countermeasure of "pre-splitting cutting roof + NPR anchor cable"(PSCR-NPR) is simultaneously proposed. According to the different deformation characteristics of the roadway, the faults are innovatively classified into three types, with α of type I being 0°-30°, α of type II being 30°-60°, and α of type III being 60°-90°. The full-cycle stress evolution paths during mining roadway traverses across different types of faults are investigated by numerical simulation. Different pinch angles α lead to high stress concentration areas at different locations in the surrounding rock. The non-uniform stress field formed in the shallow surrounding rock is an important reason for the instability of the roadway. The pre-cracked cut top shifted the high stress region to the deep rock mass and formed a low stress region in the shallow rock mass. The high prestressing NPR anchor cable transforms the non-uniform stress field of the shallow surrounding rock into a uniform stress field. PSCR-NPR is applied in the fault-through roadway of Daqiang mine. The low stress area of the surrounding rock was enlarged by 3-7 times, and the cumulative convergence was reduced by 45%-50%. It provides a reference for the stability control of the deep fault-through mining roadway.

Cutting Force Fluctuation Suppression and Error Homogenization of Noncircular Gear Hobbing Based on the Tool Shifting Method

The current research on noncircular hobbing mainly focuses on the linkage model and motion realization.However,the intermittent cutting characteristics of hobbing would increase uncertainties in the manufacturing process.In this paper,a hobbing machining model with tool-shifting characteristics was proposed to solve the problems of cutting force fluctuation and inconsistency of tooth profile envelope accuracy at different positions of the pitch curve in noncircular gear hobbing.Based on the unit cutting force coefficient method,the undeformed chip volume generated by interrupted cutting was used to characterize the fluctuation trend of the hobbing force.The fluctuation characteristics of the cutting force generated by different hobbing models were compared and analyzed.Using the equivalent gear tooth and hob slotting numbers,an analysis model of the tooth profile envelope error of the noncircular gear was constructed.Subsequently,the tooth profile envelope errors at different positions of the pitch curve were compared and analyzed based on the constructed model.The transmission structure of the electronic gearbox was constructed based on the proposed hobbing model,and the hobbing experiment was conducted based on the selfdeveloped noncircular gear CNC hobbing system.This paper proposes a hobbing method that can effectively suppress the fluctuation of the peak and whole circumference cutting force and reduce the maximum envelope error of the whole circumference gear teeth.

Cuttings transport: Back reaming analysis based on a coupled layering-sliding mesh method via CFD

Inadequate hole cleaning is one of the main reasons for inefficient operations in extended-reach drilling.The mechanism of cuttings transport under the back reaming operation,which is frequently adopted to remove the cuttings,has been investigated in this study.To this end,a coupled layering-sliding mesh method with the Eulerian-Granular approach has been established innovatively.The dynamic layering method has been employed to simulate the axial motion of the pipe,whereas the sliding mesh method has been used to simulate the pipe rotation.The back reaming operation of a connector-furnished pipe has been simulated,and the sensitive parameter analysis has been conducted.The results thus obtained demonstrate that the increase in the initial bed height,inclination,and the diameter and length of the connector causes a significant increase in the cuttings concentration.In addition,the cuttings concentration is observed to decrease significantly with the pipe rotation speed.Furthermore,two main factors contribute towards the cuttings accumulation around the connector,namely,the difference in the cross-sectional area and the pushing effect of the connector—like a“bulldozer”.The“bulldozer”effect of the connector dominates when the tripping velocity is significant compared to the velocity of the cuttings.Conversely,the effect of the difference in the cross-sectional area becomes the leading factor for cuttings accumulation.The“bulldozer”effect of the connector causes a more severe impact on hole cleaning.In both cases,increasing the tripping velocity only mildly affects the cuttings concentration.It is therefore suggested that the tripping velocity should be slower than that of the sand during the back reaming operation.Furthermore,increased fluid velocity might lead to a higher accumulated cuttings concentration around the connector when the cuttings bed has not entirely passed through the connector.A significant flow rate can be safely applied after the cuttings have passed through the connector furnished with a large diameter,such as the bottom hole assembly.This exploration serves as an essential guide to predicting and controlling tight spots while back reaming.

Unraveling engineering disturbance effects on deformation in red-bed mudstone railway cuttings:incorporating crack-facilitated moisture diffusion

Red-bed mudstone, prevalent in southwest China, poses a formidable challenge due to its hydrophilic clay minerals, resulting in expansion, deformation, and cracking upon exposure to moisture. This study addresses uplift deformation disasters in high-speed railways by employing a moisture diffusion-deformation-fracture coupling model based on the finite-discrete element method(FDEM). The model integrates the influence of cracks on moisture diffusion. The investigation into various excavation depths reveals a direct correlation between depth and the formation of tensile cracks at the bottom of the railway cutting. These cracks expedite moisture migration, significantly impacting the temporal and spatial evolution of the moisture field. Additionally, crack expansion dominates hygroscopic deformation, with the lateral coordinate of the crack zone determining peak vertical displacement. Furthermore, key factors influencing deformation in railway cuttings, including the swelling factor and initial moisture content at the bottom of the cutting, are explored. The number of tensile and shear cracks increases with greater excavation depth, particularly concerning shear cracks. Higher swelling factors and initial moisture contents result in an increased total number of cracks, predominantly shear cracks. Numerical calculations provide valuable insights, offering a scientific foundation and directional guidance for the precise prevention, control, prediction, and comprehensive treatment of mudstone-related issues in high-speed railways.

Assessing cutter-rock interaction during TBM tunnelling in granite:Large-scale standing rotary cutting tests and 3D DEM simulations

The widespread utilisation of tunnel boring machines(TBMs)in underground construction engineering requires a detailed investigation of the cutter-rock interaction.In this paper,we conduct a series of largescale standing rotary cutting tests on granite in conjunction with high-fidelity numerical simulations based on a particle-type discrete element method(DEM)to explore the effects of key cutting parameters on the TBM cutter performance and the distribution of cutter-rock contact stresses.The assessment results of cutter performance obtained from the cutting tests and numerical simulations reveal similar dependencies on the key cutting parameters.More specifically,the normal and rolling forces exhibit a positive correlation with penetration but are slightly influenced by the cutting radius.In contrast,the side force decreases as the cutting radius increases.Additionally,the side force shows a positive relationship with the penetration for smaller cutting radii but tends to become negative as the cutting radius increases.The cutter's relative effectiveness in rock breaking is significantly impacted by the penetration but shows little dependency on the cutting radius.Consequently,an optimal penetration is identified,leading to a low boreability index and specific energy.A combined Hertz-Weibull function is developed to fit the cutter-rock contact stress distribution obtained in DEM simulations,whereby an improved CSM(Colorado School of Mines)model is proposed by replacing the original monotonic cutting force distribution with this combined Hertz-Weibull model.The proposed model outperforms the original CSM model as demonstrated by a comparison of the estimated cutting forces with those from the tests/simulations.The findings from this work that advance our understanding of TBM cutter performance have important implications for improving the efficiency and reliability of TBM tunnelling in granite.

Precipitates Generation Mechanism and Surface Quality Improvement for Aluminum Alloy 6061 in Diamond Cutting

To improve the surface quality for aluminum alloy 6061(Al6061) in ultra-precision machining, we investigated the factors affecting the surface finish in single point diamond turning(SPDT)by studying influence of the precipitates generation of Al6061 on surface integrity and surface roughness.Based on the Johnson-Mehl-Avrami solid phase transformation kinetics equation, theoretical and experimental studies were conducted to build the relationship between the aging condition and the type, size and number of the precipitates for Al6061. Diamond cutting experiments were conducted to machine Al6061 samples under different aging conditions. The experimental results show that, the protruding on the chip surface is mainly Mg_(2)Si and the scratches on the machined surface mostly come from the iron-containing phase(α-, β-AlFeSi).Moreover, the generated Mg_(2)Si and α-, β-AlFeSi affect the surface integrity and the diamond turned surface roughness. Especially, the achieved surface roughness in SPDT is consistent with the variation of the number of AlFeSi and Mg_(2)Si with the medium size(more than 1 μm and less than 2 μm) in Al6061.

Hole cleaning evaluation and installation spacing optimization of cuttings bed remover in extended-reach drilling

In extended-reach or long-horizontal drilling,cuttings usually deposit at the bottom of the annulus.Once cuttings accumulate to a certain thickness,complex problems such as excessive torque and drag,tubing buckling,and pipe stuck probably occur,which results in a lot of non-productive time and remedial operations.Cuttings bed remover can efficiently destroy deposited cuttings in time through hydraulic and mechanical stirring effects.This paper aims to build a method for hole cleaning evaluation and installation spacing optimization of cuttings bed remover to improve the wellbore cleaning effect.Firstly,a Computational Fluid Dynamics approach with Eulerian—Eulerian multiphase model was utilized to investigate the mechanism of cuttings transportation,and a new type of cuttings bed remover was designed.Next,an evaluation method of hole cleaning effect of remover was established.After that,the effects of several drilling parameters on hole cleaning including flow rate of drilling fluid,rotational speed of drillpipe,rate of penetration,wellbore size,rheological property of drilling fluid,and remover eccentricity on the performance of cuttings bed remover were investigated.The results demonstrate that the new type of remover with streamline blade performs better than conventional removers.The efficiency of hole cleaning is greatly improved by increasing the rotational speed of drillpipe,flow rate of drilling fluid,remover eccentricity,and 6 rpm Fann dial reading for drilling fluid.While higher rate of penetration and large wellbore size result in worse hole cleaning.These findings can serve as an important guide for the structure optimization design of cuttings bed remover and installation spacing of removers.

Ground response and failure mechanism of gob-side entry by roof cutting with hard main roof

This study is the result of long-term efforts of the authors’team to assess ground response of gob-side entry by roof cutting(GSERC)with hard main roof,aiming at scientific control for GSERC deformation.A comprehensive field measurement program was conducted to determine entry deformation,roof fracture zone,and anchor bolt(cable)loading.The results indicate that GSERC deformation presents asymmetric characteristics.The maximum convergence near roof cutting side is 458 mm during the primary use process and 1120 mm during the secondary reuse process.The entry deformation is closely associated with the primary development stage,primary use stage,and secondary reuse stage.The key block movement of roof cutting structure,a complex stress environment,and a mismatch in the supporting design scheme are the failure mechanism of GSERC.A controlling ideology for mining states,including regional and stage divisions,was proposed.Both dynamic and permanent support schemes have been implemented in the field.Engineering practice results indicate that the new support scheme can efficiently ensure long-term entry safety and could be a reliable approach for other engineering practices.

Experimental research on affecting factors of the cutting quality of sugarcane harvesters under complicated excitations

The sugarcane field excitation,cutting forces and the engine excitation constitute complicated excitations acting on sugarcane harvesters.In this study,the sugarcane cutting mechanism under complicated excitations was analyzed.The dynamics and the mathematical models of sugarcane harvesters were established and simulated.Based on theoretical analysis,sugarcane cutting experiments were done on a self-built sugarcane harvester test platform(SHTP),designed as single-factor and the orthogonal experiments.Effects of the sugarcane field excitation characterized by the sugarcane field excitation device(SFED)output frequency,the engine excitation characterized by the actuating engine output frequency,the cutter rotating speed,the sugarcane harvester travelling speed simulated through the sugarcane transporting speed of the SHTP and the cutter inclination angle on the cutting quality of sugarcane harvesters were studied.Effects of the axial cutter vibration on three-directional cutting forces and the sugarcane cutting quality(SCQ)as well as effects of three-directional cutting forces on the SCQ were further studied.It is shown that the sugarcane field excitation,the axial cutter vibration amplitude and frequency as well as the three-directional cutting forces have significantly negative monotonic correlated effects on the SCQ while the cutter rotating speed,the sugarcane harvester travelling speed and the cutter inclination angle have significantly positive monotonic correlated effects on the SCQ.Significance levels of effects on three-directional cutting forces and the SCQ form high to low are as follow,the axial cutter vibration,the sugarcane field excitation,the cutter rotating speed,the engine excitation,the cutter inclination angle,the sugarcane harvester travelling speed.The theoretical analysis results were verified through experiment and an optimal combination was obtained with the cutter rotating speed of 700 r/min,sugarcane harvester travelling speed of 0.6 m/s and cutter inclination angle of 8º.This study can provide a reference for setting cutting parameters of sugarcane harvesters with a good SCQ.

Yield and Nutritive Values of Semi- and Non-Fall Dormant Alfalfa Cultivars under Late-Cutting Schedule in California’s Central Valley

California is one of the major alfalfa (Medicago sativa L) forage-producing states in the U.S, but its production area has decreased significantly in the last couple of decades. Selection of cultivars with high yield and nutritive value under late-cutting schedule strategy may help identify cultivars that growers can use to maximize yield while maintaining area for sustainable alfalfa production, but there is little information on this strategy. A field study was conducted to determine cumulative dry matter (DM) and nutritive values of 20 semi- and non-fall dormant (FD) ratings (FD 7 and FD 8 - 10, respectively) cultivars under 35-day cut in California’s Central Valley in 2020-2022. Seasonal cumulative DM yields ranged from 6.8 in 2020 to 37.0 Mg·ha−1 in 2021. Four FD 8 - 9 cultivars were the highest yielding with 3-yrs avg. DM greater than the lowest yielding lines by 46%. FD 7 cultivar “715RR” produced the highest crude protein (CP: 240 g·Kg−1) while FD 8 cultivar “HVX840RR” resulted in the highest neutral detergent fiber digestibility (NDFD: 484 g·Kg−1, 7% greater than the top yielding cultivars) but with DM yield intermediate. Yields and NDFD correlated positively but weakly indicating some semi- and non-FD cultivars performing similarly. These results suggest that selecting high yielding cultivars under 35-day cutting schedule strategy can be used as a tool to help growers to maximize yield while achieving good quality forages for sustainable alfalfa production in California’s Central Valley.

Endoscopic radial incision and cutting method for adult congenital duodenal webs:A case report

BACKGROUND Congenital duodenal webs are rare in adults and can lead to various symptoms such as nausea,vomiting,and postprandial fullness.The treatment for this disease is mostly surgical.Endoscopic treatment techniques have been developed and attempted for this disease.Endoscopic radial incision and cutting(RIC)techniques are reportedly very effective in benign anastomotic stricture.This case report highlights the effectiveness and safety of endoscopic RIC as a minimally invasive treatment for adult congenital duodenal webs.CASE SUMMARY A 23-year-old female patient with indigestion was referred to a tertiary hospital.The patient complained of postprandial fullness in the epigastric region.Previous physical examinations or blood tests indicated no abnormalities.Computed tomography revealed an eccentric broad-based delayed-enhancing mass-like lesion in the second portion of the duodenum.Endoscopy showed an enlarged gastric cavity and a significantly dilated duodenal bulb;a very small hole was observed in the distal part of the second portion,and scope passage was not possible.Gastrografin upper gastrointestinal series was performed,revealing an intraduodenal barium contrast-filled sac with a curvilinear narrow radiolucent rim,a typical"windsock"sign.Endoscopic RIC was performed on the duodenal web.The patient recovered uneventfully.Follow-up endoscopy showed a patent duodenal lumen without any residual stenosis.The patient reported complete resolution of symptoms at the 18-month follow-up.CONCLUSION Endoscopic RIC may be an effective treatment for congenital duodenal webs in adults.

Effects of Different Seasons on Cutting Propagation of Five Citrus Rootstocks

[Objectives]To explore the cutting propagation mode of citrus rootstock,improve the survival rooting rate of citrus rootstock,and provide theoretical guidance and technical reference for the rooting research of difficult-to-root plants such as citrus.[Methods]Five citrus rootstocks Citrus tangerina Tanaka‘Hongju’,Citrus haniana Hort‘Suanju’,Citrus limonia Osbeck‘Hongningmeng’,Citrus sinensis×Poncirus trifoliata‘Zhicheng’and Poncirus trifoliate(L)Raf.‘Zhike’were used as experimental materials to select the suitable cutting substrate for citrus rootstocks by measuring the physical properties of the substrate.Cutting was carried out in spring,summer,autumn and winter respectively.After cutting,the morphological changes of cuttings were observed regularly,and the callus rate,germination rate and rooting rate of cuttings were recorded.[Results]The best substrate for citrus rootstock cutting was peat soil,vermiculite and fine river sand(2:1:1).The callus of citrus rootstock in different cutting seasons began to appear in 10-22 d,and the callus rate reached 55%-100%.In terms of budding,the budding time was the earliest in summer and autumn,and slightly later in spring and winter;the germination rate of C.limonia Osbeck‘Hongningmeng’was the highest,and the germination rate of C.sinensis×P.trifoliata‘Zhicheng’and P.trifoliate(L)Raf.‘Zhike’was lower;in terms of rooting,C.limonia Osbeck‘Hongningmeng’had the earliest rooting time and the highest rooting rate and could reach 100%in all seasons;the rooting rate of C.tangerina Tanaka‘Hongju’was 50%-80%;the rooting rate of C.haniana Hort‘Suanju’was 60%-80%;C.sinensis×P.trifoliata‘Zhicheng’and P.trifoliate(L)Raf.‘Zhike’showed the earliest rooting time and the highest rooting rate in summer,and the latest rooting time and the lowest rooting rate in winter,which were only 14.5%.Therefore,different citrus rootstock varieties should choose the appropriate cutting time according to their own characteristics.[Conclusions]The results of this study can provide a scientific basis for a large number of cutting propagation of different citrus rootstocks,and have practical guiding significance for large-scale planting.

Cutting Propagation Technique of Pennisetum purpureum Schum

[Objectives]The paper was to study the cutting propagation technique of Pennisetum purpureum Schum and to provide a technical reference for establishing an efficient cutting propagation method.[Methods]Six treatments were set up using P.purpureum cv.Guiminyin and P.purpureum cv.Guimu-1 as test materials,including 1-node oblique insertion,1-node oblique insertion+rooting powder,1-node transverse burial,2-node oblique insertion,2-node oblique insertion+rooting powder and 2-node transverse burial.The following indices were observed and determined for P.purpureum cuttings:emergence rate,rooting rate,root number,longest root length,fresh root weight,plant height,number of tillers,number of leaves,and fresh stem and leaf weight.[Results]In the 2-node cutting+rooting powder treatment,Guiminyin and Guimu-1 exhibited the highest survival rate,root growth indices,and stem and leaf growth indices,with the emergence rates of 94.29%and 90.26%,respectively.The 2-node cutting treatment followed closely behind,while the 1-node cutting treatment had the lowest indices.Under the same treatment,Guimuyin exhibited higher mean values for plant height,number of leaves,fresh stem and leaf weight,longest root length,and fresh root weight compared to Guimu-1.However,it had lower mean number of tillers,and emergence rate and rooting rate of the 1-node cutting treatment compared to Guimu-1.[Conclusions]The P.purpureum cuttings thrived in the 2-node cutting+rooting powder treatment,and the overall cutting effect of Guiminyin was superior to that of Guimu-1.

Application of Fuyang Paper Cutting Art in Cultural and Creative Design from the Perspective of Rural Revitalization

The application significance of Fuyang paper cutting art in cultural and creative design from the perspective of rural revitalization was discussed,and the implementation principles and specific practices of applying the elements and techniques of Fuyang traditional paper cutting art in cultural and creative products with local features were analyzed to provide reference for rural revitalization and development of cultural industry.

Cutting-edge Technological Innovation Outcome Displayed at 2024 Beijing Science and Technology Week

The 2024 National Science and Technology Week and Beijing Science and Technology Week opened in Shougang Park in Shijingshan District from May 25 to June 1.Under the theme of“Carrying forward the spirit of scientists and inspiring societal innovation,”this event focused on the new-generation IT technology,medical health,energy and technology,modern agriculture and intelligent manufacturing industries.

Research on the Resistance of Cutting Mechanism of Mining Longitudinal Roadheader

In order to accurately obtain the dynamic characteristics of the cutting mechanism of the mining longitudinal roadheader,combined with the working principle of the mining longitudinal roadheader,the theoretical analysis and derivation are carried out in detail.By using ADAMS to simulate,the resistance curve and torque curve of the cutting mechanism in different directions are obtained.The results show that ADAMS can effectively predict the excavation resistance and torque of the cutting mechanism of mining longitudinal roadheader,which has certain reference value for future optimization design.

Design and Numerical Simulation of Dust Removal System for Sutomotive Iongitudinal Beam Plasma Cutting

To improve the poor efficiency of the dust removal system in the plasma cutting station of automotive longitudinal beams,and reduce the cutting surface quality degradation due to dust,a bottom-side suction dust removal system is designed,and the dust removal effect is optimized through the setting of the following dampers and diversion plates.The result of numerical simulation indicates that the particle collection rate can reach 99.44%,and the field test also proves the effectiveness of the dust removal system,which is of guiding significance for the transformation of other similar dust removal systems.

METHOD FOR SUPPRESSING CUTTING CHATTER IN NUMERICAL CONTROL MACHINE TOOLS

A new method for suppressing cutting chatter is studied by adjusting servo parameters of the numerical control （NC） machine tool and controlling the limited cutting width. A model of the cutting system of the NC machine tool is established. It includes the mechanical system, the servo system and the cutting chatter system. Interactions between every two systems are shown in the model. The cutting system stability is simulated and relation curves between the limited cutting width and servo system parameters are described in the experiment. Simulation and experimental results show that there is a mapping relation between the limited cutting width and servo parameters of the NC machine tool, and the method is applicable and credible to suppress chatter.

Dynamic Calibration of the Cutting Temperature Sensor of NiCr/NiSi Thin-film Thermocouple

In high-speed cutting, natural thermocouple, artificial thermocouple and infrared radiation temperature measurement are usually adopted for measuring cutting temperature, but these methods have difficulty in measuring transient temperature accurately of cutting area on account of low response speed and limited cutting condition. In this paper, NiCr/NiSi thin-film thermocouples（TFTCs） are fabricated according to temperature characteristic of cutting area in high-speed cutting by means of advanced twinned microwave electro cyclotron resonance（MW-ECR） plasma source enhanced radio frequency（RF） reaction non-balance magnetron sputtering technique, and can be used for transient cutting temperature measurement. The time constants of the TFTCs with different thermo-junction film width are measured at four kinds of sampling frequency by using Ultra-CFR short pulsed laser system that established. One-dimensional unsteady heat conduction model is constructed and the dynamic performance is analyzed theoretically. It can be seen from the analysis results that the NiCr/NiSi TFTCs are suitable for measuring transient temperature which varies quickly, the response speed of TFTCs can be obviously improved by reducing the thickness of thin-film, and the area of thermo-junction has little influence on dynamic response time. The dynamic calibration experiments are made on the constructed dynamic calibration system, and the experimental results confirm that sampling frequency should be larger than 50 kHz in dynamic measurement for stable response time, and the shortest response time is 0.042 ms. Measurement methods and devices of cutting heat and cutting temperature measurement are developed and improved by this research, which provide practical methods and instruments in monitoring cutting heat and cutting temperature for research and production in high-speed machining.