Ti(C, N) BASED CERAMETS AND ITS FRACTAL ANALYSIS OF FRACTURE SURFACES

Ｔｉ（Ｃ，Ｎ）ＢＡＳＥＤＣＥＲＡＭＥＴＳＡＮＤＩＴＳＦＲＡＣＴＡＬＡＮＡＬＹＳＩＳＯＦＦＲＡＣＴＵＲＥＳＵＲＦＡＣＥＳＬｉｕＮｉｎｇ（ＤｅｐａｒｔｍｅｎｔｏｆＭａｔｅｒｉａｌｓＳｃｉｅｎｃｅａｎｄＥｎｇｉｎｅｅｒｉｎｇ，Ａｎｈｕｉｉｎｓｔｉｔｕｔｅｏ...

Surface Recombination Concept as Applied to Determinate Silicon Solar Cell Base Optimum Thickness with Doping Level Effect

New expressions of back surface recombination of excess minority carriers in the base of silicon solar are expressed dependent on both, the thickness and the diffusion coefficient which is in relationship with the doping rate. The optimum thickness thus obtained from the base of the solar cell allows the saving of the amount of material needed in its manufacture without reducing its efficiency.

Effects of Specific Surface Area and Impurities of Reactive Alumina on Properties of Corundum Based Castables

Effects of specific surface area and tiny amount of impurities of reactive alumina on the workability, sinte- ring and high temperature mechanical strength of corun- dum based castables were investigated. The results show that the presence of reactive alumina with high specific surface area leads to accelerating of the hydration of calcium aluminate cement, thus shortening the working time and setting time of the castables, which can be as- cribed that the critical energy barrier for stable nuclei of hydration products of cement can be reduced by the high specific surface area of reactive alumina. The sintering of the corundum based castables can be accelerated by the reactive alumina with high specific surface area and high amount of impurities, however, the reactive alumina with too high specific surface area and impurities can al- so lead to noticeable shrinkage of castables. In addition, high temperature mechanical strength of corundum based castables can be decreased by the higher amount of trace impurities of reactive alumina due to formation of low- melting phase at high temperatures.

Surface Acoustic Wave Humidity Sensors Based on(1120) ZnO Piezoelectric Films Sputtered on R-Sapphire Substrates

ZnO films on R-sapphire substrates are prepared and characterized by x-ray diffraction and scanning electron microscopy, which indicate that the thin films are well crystallized with （1120） texture. Love wave and Rayleigh wave are used for fabrications of humidity sensors, which are excited in [1100] and [0001] directions of the （1120） ZnO piezoelectric films, respectively. The experimental results show that both kinds of sensors have good humidity response and repeatability, and the performances of the Love wave sensors are better than those of the Rayleigh wave sensors at room temperature. Moreover, the theoretical calculations of the mass sensitivity of the sensors are a/so carried out and the calculated results are in good agreement with the experimental measurements.

Laser repairing surface crack of Ni-based superalloy components

Surface crack of components of the cast nickel base superalloy was repaired with twin laser beams under proper technological conditions. One laser beam was used to melt the substrate material of crack, and the other to fill in powder material to the crack region. The experimental results show that the surface crack with the width of 0.1 ～ 0.3?mm could be repaired under the laser power of 3?kW and the scanning speed of 6 ～ 8?mm/s. The repaired deepness of crack region is below 6.5?mm. The microstructure of repaired region is the cellular crystal, columnar crystal dendrite crystal from the transition region to the top filled layer. The phases in repaired region mainly consisted of supersaturated α Co with plenty of Ni, some Cr and Al, Cr 23 C 6, Co 2B, Co Ni Mo, Ni 4B 3, TiSi and VSi. The hardness of filled layer in repaired region ranged from HV 0.2 450 to HV 0.2 500, and the hardness decreases gradually from the filled layer to joined zone.

Surface hardening of Fe-based alloy powders by Nd:YAG laser cladding followed by electrospark deposition with WC-Co cemented carbide

This paper presents the results of a study concerned with the surface hardening of Fe-based alloys and WC-8Co cemented carbide by inte- grating laser cladding and the electrospark deposition processes. Specimens of low carbon steel were processed firstly by laser cladding with Fe-based alloy powders and then by electrospark deposition with WC-SCo cemented carbide. It is shown that, for these two treatments, the electrospark coating possesses finer microstructure than the laser coating, and the thickness and surface hardness of the electrospark coating can be substantially increased.

Determination of Slip Length in Couette Flow Based on an Analytical Simulation Incorporating Surface Interaction

An analytical simulation based on a new model incorporating surface interaction is conducted to study the slip phenomenon in the Couette flow at different scales. The velocity profile is calculated by taking account of the micro-force between molecules and macro-force from the viscous shearing effect, as they contribute to the achieve- ment of the slip length. The calculated results are compared with those obtained from the molecular dynamics simulation, showing an excellent agreement. Further, the effect of the shear rate on the slip is investigated. The results can well predict the fluid flow behaviors on a solid substrate, but has to be proved by experiment.

Spectroscopic study on variations in illite surface properties after acid-base titration

FT IR, Raman microscopy, XRD, 29 Si and 27 Al MAS NMR, were used to investigate changes in surface properties of a natural illite sample after acid base potentiometric titration. The characteristic XRD lines indicated the presence of surface Al Si complexes, preferable to Al(OH) 3 precipitates. In the microscopic Raman spectra, the vibration peaks of Si O and Al O bonds diminished as a result of treatment with acid, then increased after hydroxide back titration. The varied ratio of signal intensity between IV Al and VI Al species in 27 Al MAS NMR spectra, together with the stable BET surface area after acidimetric titration, suggested that edge faces and basal planes in the layer structure of illite participated in dissolution of structural components. The combined spectroscopic evidence demonstrated that the reactions between illite surfaces and acid leaching silicic acid and aluminum ions should be considered in the model description of surface acid base properties of the aqueous illite.

Surface characteristics of rapidly solidified nickel-based superalloy pow-ders prepared by PREP

The surface microstructure and the surface segregation of FGH 95 nickel-basedsuperalloy powders prepared through plasma rotating electrode processing (PREP) have beeninvestigated by using SEM and AES. The results indicate that the surface microstructure of powderschanges from dendrite into cellular stricture as the particle size of powders decrease, and thepredominant precipitates solidified on the particle surfaces were identified as MC' type carbidesenriched with Nb and Ti. It was also indicated that along with the depth of particle surfaces, thesegregation layer of S, C and O elements are thick, and that of Ti, Cr elements are thin for largesire powders while they are in reverse for median size particles.

Improved light extraction of GaN-based light-emitting diodes with surface-textured indium tin oxide electrodes by nickel nanoparticle mask dry-etching

GaN-based light-emitting diodes （LEDs） with surface-textured indium tin oxide （ITO） as a transparent current spreading layer were fabricated. The ITO surface was textured by inductively coupled plasma （ICP） etching technology using a monolayer of nickel （Ni） nanoparticles as the etching mask. The luminance intensity of ITO surface-textured GaN-based LEDs was enhanced by about 34% compared to that of conventional LED without textured ITO layer. In addition, the fabricated ITO surface-textured GaN-based LEDs would present a quite good performance in electrical characteristics. The results indicate that the scattering of photons emitted in the active layer was greatly enhanced via the textured ITO surface, and the ITO surface-textured technique could have a potential application in improving photoelectric characteristics for manufacturing GaN-based LEDs of higher brightness.

Effects of Chairside Polishing and Brushing on SurfaceRoughness of Acrylic Denture Base Resins

The effects of 3 chairside polishing kits and mechanical brushing on the surface roughness of 3 different acrylic denture base resins were compared. Acrylic denture base resins （auto-polymerizing, heat-polymerizing, injected heat-polymerizing resins） were examined after a tungsten carbide bur, and after chairside polishing using 3 polishing kits and pumice. The specimens were subjected to mechanical brushing using a wear tester to simulate 30 000 strokes of brushing. The surface roughness of the acrylic denture base resin specimens was measured using a contact pro-filometer. After the test, the random polished acrylic resins were evaluated by scanning electron mi-croscopy （SEM） and atomic force microscopy （AFM）. Acrylic denture base resins polished using the 3 types of polishing kits had a smoother surface than those finished with the tungsten carbide bur （p〈0.05）. The surface of the resin polished by a TC cutter exceeded the Ra of 0.2 μm （p〈0.05）. The auto-polymerizing resin showed a significantly higher surface roughness than the heat-polymerizing resin and injected heat-polymerizing resin （p〉0.05）. In the case of polishing step wise, there was almost no change in surface roughness after brushing （p〉0.05）.

A Note on Reviving the Goddard Satellite-Based Surface Turbulent Fluxes (GSSTF) Dataset

Accurate sea surface flux measurements are crucial for understanding the global water and energy cycles. The oceanic evaporation, which is a major component of the global oceanic fresh water flux, is useful for predicting oceanic circulation and transport. The global Goddard Satellite-based Surface Turbulent Fluxes Version-2 （GSSTF2; July 1987–December 2000） dateset that was o？cially released in 2001 has been widely used by scientific community for global energy and water cycle research, and regional and short period data analyses. We have recently been funded by NASA to resume processing the GSSTF dataset with an objective of continually producing a uniform dataset of sea surface turbulent fluxes, derived from remote sensing data. The dataset is to be reprocessed and brought up-to-date （GSSTF2b） using improved input datasets such as a recently upgraded NCEP/DOE sea surface temperature reanalysis, and an upgraded surface wind and microwave brightness temperature V6 dataset （Version 6） from the Special Sensor Microwave Imager （SSM/I） produced by Remote Sensing Systems （RSS）. A second new product （GSSTF3） is further proposed with a finer temporal （12-h） and spatial （0.25° × 0.25°） resolution. GSSTF2b （July 1987–December 2008） and GSSTF3 （July 1999–December 2009） will be released for the research community to use by late 2009 and early 2011, respectively.

Knotted pictures of the Bell bases on the surface of a trivial torus

By means of the method of torus knot theory, this paper gives the complete processes of obtaining the knotted pictures of four Bell b^es from the knotted pictures of four basic two qubit states.

Surface Metallurgy of Nickle Base Superalloy

The Double Glow Plasma Surface Alloying Technique, the Xu-Tee Process, is a new method to produce high quality alloying layer on the surface of less expensive materials. By using thes technique, the surface alloying layer similar to superalloy Inconel 625 has been obtained on the surface of three kinds of melallic materials (low carbon steel, industrial pure iron, stainless steel Cr18Ni9). The results of the composition and microstructure analyzed by Scanning Electron Microscopy (SEM) and X-Ray Uffrachon (XRD) show that the alloying layer consistS of y matrix and several precipitates (Laves intermetallic phase and carbide etc.). The electrochemical corrosion results show that the surface alloying layer formed on the surface of stainless steel and industrial pure iron have better corrosion resistance than that of nickel base alloy inconel 625 and stainless steel Cr18Ni9 in 3.5%NaCl solution. The exper iments indicate that it is an effective way to obtain the gradient surface alloying layer on the surfaces of steels by using Double Glow Plasma Surface Alloying Technique.

Deposition of DLC Coating on Biomedical TiNi Alloys by Plasma Based Ion Implantation to Improve Surface Properties

Diamond-like carbon （DLC） films were successfully deposited on Ti- 50.8 at% Ni using plasma based ion implantation （PBII） technique. The influence of the pulsed negative bias voltage applied to the substrate from 12 kV to 40 kV on the microstracture, nano-indentation hardness and Young＇ s modulus, the surface characteristics and corrosion resistant property as well as hemocompatibility were investigated. The experimental resalts showed that C 1 s peak depended heavily on the bias voltage. With the increase of bias voltage, the ratio of sp2 / sp3 first decreased, reaching a minimum value at 20 kV, and then increased. The DLC coating deposited at 20 kV showed the highest hardness and elastic modulus values as a result of lower sp2/sp3 ratio. The RMS values first decreased from 7.202nm（12 kV） to 5.279 nm（20 kV）, and then increased to 11.449 nm（30 kV） and 7.060 nm（ 40 kV）. The uncoated TiNi alloy showed severe pitting corrosion, due to the presence of Cl-ions in the solution. On the contrary, the DLC coated sample showed very little pitting corrosion and behaved better corrosion resistant property especially for the specimens deposited at 20 kV bias voltages. The platelet adhesion test show that the hemocompatibility of DLC coated TiNi alloy is much better than that of bare TiNi alloy, and the hemocompatibility performance of DLC coated TiNi alloy deposited at 20 kV is superior to that of other coated specimens.

Ray tracing/correlation approach to estimation of surface-based duct parameters from radar clutter

This paper describes a technique to estimate surface-based duct parameters by using a simple ray tracing/correlation method. The approach is novel in that it incorporates the Spearman rank-order correlation scheme between the observed surface clutter and the surface ray density for a given propagation path. The simulation results and the real data results both demonstrate the ability of this method to estimate surface-based duct parameters. Compared with the results obtained by a modified genetic algorithm combined with the parabolic wave equation, the results retrieved from the ray tracing/correlation scheme show a minor reduction in accuracy but a great improvement on computation time. Therefore the ray tracing/correlation method might be used as a precursor to more sophisticated and slower techniques, such as genetic algorithm and particle filters, by narrowing the parameter search space and providing a comprehensive and more efficient estimation algorithm.

Volume and Surface Nucleation of Crystals in Glass Based on Blast-Furnace Slag

Using differential thermal analysis, X-ray phase analysis, electron microscopy, and optical microscopy, the nucleation of crystals in glass obtained by blending metallurgical slag with silicon dioxide has been studied. The type of crystallization (homogeneous or heterogeneous, volume or surface) is revealed for each of nine compositions of synthesized glass. It is shown that the first crystalline phase in a volume crystallizing glass is perovskite (CaO·TiO2);in this phase a nucleation of the main phase occurs: melilite (solid solution of gehlenite 2CaO·Al2O3·SiO2 in akermanite 2CaO·MgO·2SiO2). The fundamental characteristics of homogeneous (for a catalizing phase, perovskite) and heterogeneous (for a catalyzed phase, melilite) of crystallization are determined: the steady state nucleation rate Ist, time of unsteady state nucleation τ, crystal growth rate U, and activation energy of frictional flow. The temperature dependences of Ist, τ, and U are obtained. The kinetics of the crystallization of glass is studied and the rates of the surface crystal growth are determined in the glass of nine compositions. The influence of grinding the particles of the original glass on the sequence of deposition of the crystalline phases was studied. Practical recommendations are presented for the use of blast-furnace slag as a raw material for the synthesis of glass and their further utilization.

A Novel Copper(Ⅱ)Complex Based on 4-Amino-1,2,4-triazole Schiff-base:Synthesis,Crystal Structure,Spectral Characterization,and Hirshfeld Surface Analysis

A novel copper complex Cu2（L）4（1, HL = 2-ethoxy-6-（[1,2,4]triazol-4-yliminomethyl）-phenol） has been synthesized and characterized by IR, single-crystal X-ray diffraction, and elemental analysis（CHN）. The single crystal belongs to the triclinic system, space group P1 with a = 10.0991（10）, b = 10.5280（12）, c = 10.5777（11） A, α = 97.230（9）, β = 90.640（8）, γ = 92.412（9）°, Mr = 1052.05, V = 1114.6（2） A3, Z = 1, Dc = 1.567 g/cm3, F（000） = 542, μ = 1.029 mm–1, R = 0.0562 and w R = 0.1562. The fluorescence and electrochemiluminescence（ECL） of 1and HL ligand were studied. The luminescence properties of 1 can be attributed to the ligand-metal charge transfer.

Efficient volume preserving approach for skeleton-based implicit surfaces

This paper presents an efficient way to preserve the volume of implicit surfaces generated by skeletons. Recursive subdivision is used to efficiently calculate the volume. The criterion for subdivision is obtained by using the property of density functions and treating different types of skeletons respectively to get accurate minimum and maximum distances from a cube to a skeleton. Compared with the criterion generated by other ways such as using traditional Interval Analysis, Affine Arithmetic, or Lipschitz condition, our approach is much better both in speed and accuracy.

Waveguide Mode Splitter Based on Multi-mode Dielectric-Loaded Surface Plasmon Polariton Waveguide

In photonie integrated circuits, information is usually encoded in the optical path. In this work, based on the multi-mode dielectric-loaded surface plasmon polariton waveguide, we numerically design a directional coupler, which can divide the different waveguide eigenmodes into different optical paths. The results show a possibility to encode information onto different waveguide modes. We also experimentally demonstrate that the splitting ratio of this directional coupler structure can be tuned without changing its size.