Numerical Analysis of Fiber Reinforced Polymer-Confined Concrete under Cyclic Compression Using Cohesive Zone Models

This paper examines the mechanical behavior offiber reinforced polymer(FRP)-confined concrete under cyclic compression using the 3D cohesive zone model(CZM).A numerical modeling method was developed,employing zero-thickness cohesive elements to represent the stress-displacement relationship of concrete potential fracture surfaces and FRP-concrete interfaces.Additionally,mixed-mode damage plastic constitutive models were pro-posed for the concrete potential fracture surfaces and FRP-concrete interface,considering interfacial friction.Furthermore,an anisotropic plastic constitutive model was developed for the FRP composite jacket.The CZM model proposed in this study was validated using experimental data from plain concrete and large rupture strain(LRS)FRP-confined concrete subjected to cyclic compression.The simulation results demonstrate that the pro-posed model accurately predicts the mechanical response of both concrete and FRP-confined concrete under cyc-lic compression.Lastly,various parametric studies were conducted to investigate the internal failure mechanism of FRP-confined concrete under cyclic loading to analyze the influence of the inner friction plasticity of different components.

Finite element analysis of strain distribution in ZK60 Mg alloy during cyclic extrusion and compression

Finite element method was used to study the strain distribution in ZK60 Mg alloy during multi-pass cyclic extrusion and compression （CEC）. In order to optimize the CEC processing, the effects of friction condition and die geometry on the distribution of total equivalent plastic strain were investigated. The results show that the strain distributions in the workpieces are inhomogeneous after CEC deformation. The strains of the both ends of the workpieces are lower than that of the center region. The process parameters have significant effects on the strain distribution. The friction between die and workpiece is detrimental to strain homogeneity, thus the friction should be decreased. In order to improve the strain homogeneity, a large corner radius and a low extrusion angle should be used.

Microstructure and mechanical properties of AM60B magnesium alloy prepared by cyclic extrusion compression

The cyclic extrusion compression （CEC） process was introduced into the AM60B magnesium alloy. The use of the CEC process was favorable for producing finer microstructures. The results show that the microstructure can be effectively refined with increasing the number of CEC passes. Once a critical minimum grain size was achieved, subsequent passes did not have any noticeable refining effect. As expected, the fine-grained alloy has excellent mechanical properties. The micro-hardness, yield strength, ultimate tensile strength and elongation to failure of two-pass CEC formed alloy are 72.2, 183.7 MPa, 286.3 MPa and 14.0%, but those of as-cast alloy are 62.3, 64 MPa, 201 MPa and 11%, respectively. However, there is not a clear improvement of mechanical properties with further increase in number of CEC passes in AM60B alloy. The micro-hardness, yield strength, ultimate tensile strength and elongation to failure of four-pass CEC formed alloy are 73.5, 196 MPa, 297 MPa and 16%, respectively.

Effect of long-term cyclic compression loading on the structural evolution of trabecular bone

Dynamic remodeling of bone tissue is mediated by the synergistic effects of osteoblast-driven bone formation and Osteoclast-dominated bone resorption.However,how bone cells perceive the mechanical stimuli and regulate bone remodeling have not been fully understood.This study aims to evaluate the effect of cyclic compression loading on trabecular microstructure for 42 days and identify the relationship between the evolution of trabecular microstructure and cell distribution.The eighth caudal vertebrae of rats were subjected to long-term cyclic compression loading with different frequencies.The compression displacement is 1 mm.In vivo micro-computed tomography was performed at 0,14,28 and 42 days to determine the structural parameters.The bone volume fraction(BV/TV)in the 1 Hz cyclic compression loading group was significantly higher than that in the control and 10 Hz groups,whereas the trabecular separation(Tb.Sp)was significantly lower.The 10 Hz cyclic compression group had the lowest BV/TV and highest Tb.Sp.After 14 days of loading,the BV/TV values of 1 Hz group were 29.62%and 41.6%higher than those of the control and 10 Hz groups,respectively.Conversely,the Tb.Sp of 1 Hz group was approximately 12.33%and 16.52%lower than that of the control and 10 Hz group,respectively.More bone formation and less bone resorption were observed in the 1 Hz group than the control group.In addition,more osteoblasts were attached to the area of bone formation,while more osteoclasts were located in the area of bone resorption.These findings may provide a basis for further understanding mechanical stimulation-regulated bone remodeling.

Investigating the Damaging Effects of the Cyclic Discharge in the Uni-Axial Compression of <i>Raphia vinifera</i>L. Arecacea

The bamboo stem, when mature 5 to 6 years, serves as a building material for modest houses and its marrow as packaging purposes. One of the strains related to the uses of bamboo stem is most often the compression towards the axial direction. The phenomenon of damage is very often observed during such loading. The present study on raffia aims to analyze this phenomenon through cyclical stresses as usual. From the results obtained, it was observed in the stress-strain plane, that the area of the hysteresis loops and the residual strain evolve with two parameters: the number of cycles and the stress peaks. The study of energy dissipation has shown that it evolves according to an exponential law as a function of the number of cycles. The distribution of the energy rate along a stem shows that the samples from the zone close to the base store twice (0.0412 MJ/m3) more energy than the samples taken from the top of the foliage (0.019 MJ/m3).

Cell membrane tensile strain under cyclic compression:A viscoelastic myoblast finite element model

Cyclic mechanical stimulation could lead to subsequent biomechanical and biological effects on cells.Viscoelastic cells could deform or show energy dissipation with hysteresis behavior in response to external cyclic compression.The aim of this study was to investigate the effect of cyclic compression on a single viscoelastic myoblast through a confocal–based cell–specific finite element model,including cell membrane tensile strain and damaged elements.Sinusoidal compression was applied to the apical surface of the myoblast(cell membrane)with compressive stress of 500
500 Pa(with stress offset at 500 Pa and amplitude of 500 Pa)at 0 Hz(static compression of 500 Pa),0.25 Hz,0.5 Hz,0.75 Hz,1 Hz,5 Hz,and 10 Hz.Results showed that the ratio of average tensile strain integral in all cell membrane elements over a certain period of time(T)to that duration(T)(MAS index)decreased under cyclic compression compared to that of static compression in the short term(within 4 s).Furthermore,compared to static compression,the percentage of damaged elements of cell membrane under cyclic compression decreased assuming a 3%cell membrane tensile strain damage threshold.The optimal cyclic compression frequency 0.25 Hz led to the largest difference of MAS index under cyclic compression and static compression.These results may provide support for the application of cyclic compressive stimulation in the prevention of cell damage.

Processing and characterization of AZ91 magnesium alloys via a novel severe plastic deformation method:Hydrostatic cyclic extrusion compression(HCEC)

Capability of a novel severe plastic deformation(SPD)method of hydrostatic cyclic extrusion compression(HCEC)for processing of hcp metallic rods with high length to diameter ratios was investigated.The process was conducted in two consecutive cycles on the AZ91 magnesium alloy,and microstructural evolution,mechanical properties and corrosion behavior were investigated.The results showed that the HCEC process was successively capable of producing ultrafine-grained long magnesium rods.Its ability in improving strength and ductility simultaneously was also shown.The ultimate tensile strength and elongation to failure of the sample after the second cycle of the process were improved to be 2.46 and 3.8 times those of the as-cast specimen,respectively.Distribution of the microhardness after the second cycle was uniform and its average value was increased by 116%.The potentials derived from the polarization curves were high and the currents were much low for the processed samples.Also,the diameter of the capacitive arcs derived from the Nyquist curves was large in the HCEC processed samples.The finite element analysis indicated the independency of HCEC load from the length in comparison to the conventional CEC.HCEC is a unique SPD method,which can produce long ultrafine-grained rods with a combination of superior mechanical and corrosion properties.

Properties inhomogeneity of AM60 magnesium alloy processed by cyclic extrusion compression angular pressing followed by extrusion

A new severe plastic deformation(SPD)technique for improvement of the metallurgical properties of the magnesium alloys is presented.In this process,a cyclic extrusion compression angular pressing(CECAP)process is followed by an extrusion step in the outlet playing the role of additional back pressure.Therefore,more uniform and enhanced mechanical properties are expected in comparison with equal channel angular pressing(ECAP).In order to evaluate the effectiveness and capabilities of this new method,an AM60 magnesium alloy was processed.Finite element results exhibited a significant increase in strain values as well as uniform strain distribution for the new method.In addition,~110%increase in compressive stress was observed in new method compared to the conventional ECAP.Experimental results revealed a noticeable increase in the hardness and strength of the specimens processed by the new technique as a result of the formation of finer grains and more homogeneous microstructure with good distribution of refinedβ-phase along the boundaries.It may be concluded that the new process is very promising for future magnesium alloy products.

Microstructure and texture characteristics of ZK60 Mg alloy processed by cyclic extrusion and compression

The microstructure and crystallographic texture characteristics of an extruded ZK60 Mg alloy subjected to cyclic extrusion and compression(CEC) up to 8 passes at 503 K were investigated.The local crystallographic texture,grain size and distribution,and grain boundary character distributions were analyzed using high-resolution electron backscatter diffraction(EBSD).The results indicate that the microstructure is refined significantly by the CEC processing and the distributions of grain size tend to be more uniform with increasing CEC pass number.The fraction of low angle grain boundaries(LAGBs) decreases after CEC deformation,and a high fraction of high angle grain boundaries(HAGBs) is revealed after 8 passes of CEC.Moreover,the initial fiber texture becomes random during CEC processing and develops a new texture.

Fatigue behavior and cumulative damage rule of concrete under cycli ccompression with constant confined stress

The effects of different lateral confinement stress on the fatigue behavior and cumulative damage of plain concrete were investigated experimentally. Eighty 100mm×100mm×100mm specimens of ordinary strength concrete were tested with constant-or variable-amplitude cyclic compression and lateral confinement pressure in two orthogonal directions. A fatigue equation was gained by modifying the classical Aas-Jakobsen S-N equation and used for taking into account the effect of the confined stress on fatigue strength of plain concrete. The present study indicates that the fatigue failure is greatly influenced by the sequence of applied variable-amplitude fatigue loading, and Miner’s rule is inapplicable to predict the residual fatigue life, especially in the sequence of low to high. The present research also shows that the exponent d of the Corten-Dolan’s damage formula is a constant depending on the materials and the levels of load spectrum, and d can be determined through the two-stage fatigue tests. The residual fatigue lives predicted by Corten-Dolan’s damage formula are found to be in good agreement with the results of the experiments.

Grain refinement of magnesium alloys processed by severe plastic deformation

Grain refinement of AZ31 Mg alloy during cyclic extrusion compression （CEC） at 225-400 ℃ was investigated quantitatively by electron backscattering diffraction （EBSD）. Results show that an ultrafine grained microstructure of AZ31 alloy is obtained only after 3 passes of CEC at 225 ℃. The mean misorientation and the fraction of high angle grain boundaries （HAGBs） increase gradually by lowering extrusion temperature. Only a small fraction of {101^-2} twinning is observed by EBSD in AZ31 Mg alloys after 3 passes of CEC. Schmid factors calculation shows that the most active slip system is pyramidal slip {101^-1}〈1120〉and basal slip {0001}〈1120〉 at 225-350 ℃ and 400 ℃, respectively. Direct evidences at subgrain boundaries support the occurrence of continuous dynamic recrystallization （CDRX） mechanism in grain refinement of AZ31 Mg alloy processed by CEC.

The effect of severe plastic deformation on the Mg properties after CEC deformation

In this study,the effect of severe plastic deformation on the Mg grain refinement and recovery mechanism was investigated.Technical pure magnesium was deformed at room temperature by cycling extrusion-compression(CEC)process up to large deformation.Several steps of deformation have been used by applying 1,2 and 4 passes of CEC giving a total effective plastic strain ofε=3.1.Mechanical and structural properties of Mg in initial state and the states after successive steps of deformation were investigated.The mechanical properties were determined by microhardness and compression tests at room temperature.The structural investigations involved light microscope observations,electron back scattered diffraction and texture measurements by X-ray diffraction.It was found that the CEC process refines the grain size down to 6.4μm and reduces strong rolling texture components.However,only the first two passes had a strong effect on mechanical properties while a larger number of CEC cycles(above 4)led to failure of the samples with a small effect on hardness.This observation correlates with texture evolution indicating a more random orientation distribution that slows down the typical for hep metals rapid work hardening.It was found that the CEC process activated twin dynamic recrystallization in deformed Mg.This process led to the formation of new randomly oriented grains inside the twinned areas and as a consequence it reduced the strong rolling texture components.

Enhanced Strength and Ductility Due to Microstructure Refinement and Texture Weakening of the GW102K Alloy by Cyclic Extrusion Compression

The cyclic extrusion compression （CEC） was applied to severely deform the as-extruded GW102K （Mg- 10.0Gd-2.0Y-0.5Zr, wt%） alloy at 350, 400, and 450 ℃, respectively. The microstructure, texture, and grain boundary character distribution of the CECed alloy were investigated in the present work. The mechan- ical properties were measured by uniaxial tension at room temperature. The crack initiation on the longitudinal section near the tensile fracture-surface was investigated by high-resolution scanning elec- tron microscopy （SEM）. The result shows that the microstructure was dramatically refined by dynamic recrystallization （DRX）. The initial fiber texture was disintegrated and obviously weakened. The 8-passes/ 350 ℃ CECed alloy exhibited yield strength of 318 MPa with an elongation-to-fracture of 16.8%, increased by 41.3% and 162.5%, respectively. Moreover, the elongation-to-fracture of the 8-passes/450 ℃ CECed alloy significantly increased more than 3 times than that of the received alloy. The cracks were mainly initi- ated at twin boundaries and second phase/matrix interfaces during tensile deformation. The microstructure refinement was considered to result in the dramatically enhanced of the strength and ductility. In ad- dition, the texture randomization during CEC is beneficial for enhancing ductility. The standard positive Hall-Petch relationships have been obtained for the CECed GW102K alloy.

Microstructure Evolution and Grain Coarsening Behaviour During Partial Remelting of Cyclic Extrusion Compression Formed AZ61 Magnesium Alloy

The effects of CEC passes, isothermal holding time and reheating temperature on the microstructure evolution and grain coarsening behaviour of AZ61 magnesium alloy produced by the recrystallisation and partialmelting （RAP） process were investigated. Before partial remelting, as-cast AZ61 alloy was deformed by cyclic extrusion compression （CEC） with one pass and two pass at 330 ℃. After CEC, the microstructure consisted of unrecrystallized grains and deformed eutectic compounds. Increasing isothermal holding time resulted in the formation of spheroidal grains surrounded by liquid films. With increasing the isothermal holding time, the solid grain size increased and the degree of spheroidization was improved. With increasing the reheating temperature, namely increasing liquid fraction, the solid grain size obviously decreased during the period from 560 ℃ to 570 ℃ and then slightly increased after 570 ℃, while the shape factor increased monotonously. During partial remelting, increasing reheating temperature can properly short the isothermal holding time to obtain fine structure. Moreover, increasing the numbers of CEC passes could produce finer semi-solid microstructure. The coarsening behavior of solid grains in the semi-solid state obeys Ostwald ripening and grain coalescence mechanisms. The coarsening rate constant, K, 595 ℃. After CEC plus partial remelting, the ideal and fine was suitable for thixoforming. was 80μm^3.s^-1 for samples partially remelted at semi-solid state structure can be obtained, which

软黏土中桶形基础竖向循环加载超重力离心模型试验研究

桶形基础越来越广泛应用于海洋油气平台、海上风机、输电塔、防波堤等构筑物,研究其循环承载特性对以上构筑物服役安全性具有重要意义。通过在软黏土中开展单桶循环上拔以及小间距群桶循环上拔和循环下压超重力离心模型试验,发现循环上拔地基破坏模式为整体破坏,裂隙均呈现圆弧形,循环下压呈现渐进式整体破坏模式,下压过程的挤压作用可明显减小桶周泥面高度,导致其承载力降低。模拟双向受荷工况的循环上拔试验在5次加载后荷载弱化系数开始趋于稳定,远早于单向受荷工况;单向和双向受荷工况循环上拔荷载弱化系数残余稳定值分别为0.31和0.32,循环下压荷载弱化系数最小值为0.35,表明不同加载方式竖向循环荷载作用下,此三者大小均可用软黏土地基灵敏度倒数预估。

A scalable versatile methodology to construct micro/nano open-cell polypropylene foam with high oil adsorption capacity and speed

Oil pollution is a serious environmental and natural resource problem.Traditional adsorption materials for oil–water separation have limitations in terms of their preparation cost,reusability,and mechanical properties.Among the conventional adsorption materials,super-hydrophobic/super-lipophilic materials are easily contaminated by oil.In this study,polypropylene(PP)is used as a foam substrate to prepare an open-cell PP foam via hot pressing,supercritical CO_(2) foaming,and electron beam(EB)irradiation.The impact of EB irradiation dose on the open-cell content of PP foam can lead to cell wall rupture,resulting in an open-cell structure that enhances oil-water separation performance.At an absorbed radiation dose of 200 kGy,the PP foams exhibit optimal oil–water separation performance,cyclic compression stability,heat insulation,and preparation cost.The open-cell content of PP foam is increased to 86.5%,the adsorption capacity for diesel oil is 42.8 g/g,and the adsorption efficiency remains at 99.6%after 100 cycles of oil desorption in a complex pH environment.Meanwhile,cracks and nano-voids simultaneously promote the capillary action of oil,and the oil transport rate is 0.0713 g/(g·s).This study provides a new concept for the preparation of open-cell polymer foams that can meet the demand for high oil-absorption capacity under complex acid-base pH conditions.

Experimental study on slender buckling-restrained knee braces with round steel bar cores

This study aimed to investigate a novel slender buckling-restrained knee brace damper (BRKB) for welded and weld-free steel framing systems. The proposed BRKB adopts steel bar cores connected by a central coupler and restrained by tube buckling restrainers with a cover tube supporter. The advantages of the proposed damper include easy assembly compared to conventional buckling restrained braces, and high architectural flexibility for the retrofitting of large-span weld-free or welded steel moment-resisting systems. Specifically, by increasing the number of contraction allowances, undesirable failure mechanisms that are global instability and local buckling of the restrainer ends can be effectively suppressed because the more uniform plastic deformation of the core bar can be achieved longitudinally. In this study, displacement-controlled compression and cyclic loading tests were carried out to investigate the deformation capacities of the proposed BRKBs. Structural performance metrics associated with both loading tests, such as strength capacities, strains at the cover tubes and buckling restrainers, and hysteretic behaviors of the proposed damper under cyclic loads, were measured and discussed. Test results revealed that the geometrical characteristics of the cover tubes and adopted contraction allowances at the dampers play essential roles in their load-bearing capacities.

Effect of different processings on mechanical property and corrosion behavior in simulated body fluid of Mg-Zn-Y-Nd alloy for cardiovascular stent application

The biomagnesium alloys have been considered to be one of the most potential biodegradable metal materials due to its good mechanical compatibility, biological compatibility, biological security and biodegradable characteristics. However, the two major problems of high degradation rates in physiological environment and low mechanical properties prevent the development of biomagnesium alloys. In the present work, the samples of Mg-Zn-Y-Nd alloy were prepared by cyclic extrusion compression （CEC） and equal channel angular pressing （ECAP）. The microstructures, mechanical properties of alloy and its corrosion behavior in simulated body fluid （SBF） were evaluated. The results reveal that Mg-Zn-Y-Nd alloy consists of equiaxial fine grain structure with the homogeneous distribution of micrometer size and nano-sized second phase, which was caused by the dynamic recrystallization during the ECAP and CEC. The corrosion resistance of alloy was improved. The tensile and corrosion resistance were improved, especially the processed alloy exhibit uniform corrosion performances and decreased corrosion rate. This will provide theoretical ground for Mg-Zn-Y-Nd alloy as vascular stent application.