A Piecewise Linear Slope Compensation Circuit for DC-DC Converters

To prevent sub-harmonic oscillation and improve the stability and load capacity of the system,a piecewise linear slope compensation circuit is designed. Compared with the traditional design, this circuit provides a compensation signal whose slope varies from different duty cycles at - 40-85℃ ,and reduces the negative effect of slope compensation on the system＇s load capacity and transient response. A current mode PWM Boost DC-DC converter employing this slope compensation circuit is implemented in a UMC 0.6μm-BCD process. The results indicate that the circuit works well and effectively,and the load capacity is increased by 20%. The chip area of the piecewise linear slope compensation circuit is 0.01mm^2 ,which consumes only 8μA quiescent current,and the efficiency ranges up to 93%.

Current Share Control IC Design for Paralleled DC/DC Converters

To keep even current distribution among DC/DC converters in a paralleled power system,an automatic master-slave control （AMSC） current sharing scheme is presented,which was implemented by a current share control IC. A current feedback loop for output voltage adjustment is proposed for low signal distortion. Moreover,a special startup control logic is designed to improve startup timing and to speed up the initial current sharing. It was completed in 1.5μm bipolar-CMOS-DMOS （BCD） technology with an area of 3.6mm^2 . Using it,a paralleled power system of two DC/DC converters capable of outputting 12V/3A was built. Experimental results show that the current sharing error at full load is kept within 1%.

A Novel Hybrid DPWM for Digital DC-DC Converters

We present a new hybrid digital pulse-width modulator （DPWM） for digital DC-DC converters that employs a ring-oscillator/counter structure. Based on a temperature/process compensation technique and a novel digital controller, the proposed DPWM can not only offer temperature/process-independent pulse widths, but also operate at a much higher clock frequency than the existing delay-line/counter DPWM structure. Post-simulation results show that with our DPWM, the system clock frequency reaches 156.9MHz while the worst variation,in a temperature range of 0 to 100℃under all process corners,is only± 9.4%.

Design Criterion for Interleaving and Magnetically Integrated Bidirectional DC/DC Converters

双向DC/DC变换器中大功率储能电感的设计是一件困难而具有挑战性的工作,提出研究双向DC/DC变换器的交错并联磁集成理论以克服这一困难。将三相Buck＋Boost双向DC/DC变换器的所有相电感集成为一个耦合电感,对磁集成后变换器运行在Buck模式下的稳态电流纹波和暂态响应速度进行深入研究,给出三相Buck＋Boost交错并联磁集成双向DC/DC变换器运行在Buck模式下的设计准则,即在设计这种变换器时,应根据占空比的大小及稳态相电流纹波和暂态总输出电流响应速度的技术要求,利用该文所给出的设计公式和设计区域选择磁集成耦合电感的反向耦合系数。仿真和实验验证了理论分析的正确性。

AC/DC Matrix Converters for V2G Applications

由于当前V2G系统中普遍采用的电压型脉宽调制（pulse width modulation,PWM）整流方案中所存在的蓄电池电压匹配、功率体积比及系统效率问题,提出一种采用AC/DC矩阵变换器的解决方案。针对经典电流空间矢量调制策略中充电电流纹波较大的缺点,提出一种在全输出范围内减小充电电流纹波的分段优化调制策略,并深入对比分析这两种调制策略下充电电流纹波的大小。仿真和实验结果表明,所提分段优化调制策略的正确性和可行性。

Study and Production of a Two-Stage DC/DC DC/AC Converter for Generating an Alternating Voltage from a Direct Voltage Supplied by a Photovoltaic Array

This article presents an ongoing study of the design of a DC-AC inverter using a single renewable energy source. The proposed approach makes it possible to produce an output with an H-bridge or full bridge and a single energy source. To this end, the performance of the inverter was studied first by means of a simulation and then with the implementation of an experimental device.

State Variable Model for Considering the Parasitic Inductor Resistance on the Open Loop Performance of DC to DC Converters

This paper shows DC and small-signal circuit models for the PWM DC to DC buck, boost and back/ boost converters with the equivalent series resistance of the inductor. The DC voltage transfer function and the efficiency of the converter are derived from the DC model. Small-signal open-loop characteristics are derived from the small-signal model based on a state variable model. A design example proves the performance of the circuit and verification of the model.

A Flux DC Bias Suppression Scheme of Single-stage Full-bridge PFC Converters Based on Dead Zone Adjustment

由于单级桥式功率因数校正（power factor correction,PFC）AC/DC变换技术电路的特点,导致高频变压器存在偏磁现象,影响了系统正常工作。传统方式通过增加变压器气隙或使用隔直电容来防止变压器出现偏磁,但是该类方案影响了系统性能,并增加了电路的复杂程度。结合有源钳位单级PFC变换器工作特点,提出一种基于死区调节的偏磁抑制策略,通过改变系统的开关时序,能够有效抑制偏磁,具有不增加主电路复杂程度、不影响系统性能、数字控制和模拟控制都能够实现等优点。在提出抑制策略的基础上,设计实现电路,给出死区设计方法及影响规律,最后进行实验研究。理论分析及实验结果表明,该策略能够在不影响系统性能的基础上,有效抑制单级桥式PFC变换器的高频变压器偏磁。

Paralleled DC-DC Power Converters Sliding Mode Control with Dual Stages Design

This paper proposes the new cascaded series parallel design for improved dynamic performance of DC-DC buck boost converters by a new Sliding Mode Control (SMC) method. The converter is controlled using Sliding Mode Control method that utilizes the converter’s duty ratio to determine the skidding surface. System modeling and simulation results are presented. The results also showed an improved overall performance over typical PID controller, and there was no overshoot or settling time, tracking the desired output nicely. Improved converter performance and robustness were expected.

Simulations of the Performance of Maximum Power Point Tracking Algorithms Based on Experimental Data According to the Topologies of DC-DC Converters

Maximum Power Point Tracking (MPPT) algorithms are now widely used in PV systems independently of the weather conditions. In function of the application, a DC-DC converter topology is chosen without any previous performance test under normal weather conditions. This paper proposes an experimental evaluation of MPPT algorithms according to DC-DC converters topologies, under normal operation conditions. Four widely used MPPT algorithms i.e. Perturb and Observe (P & O), Hill Climbing (HC), Fixed step Increment of Conductance (INCF) and Variable step Increment of Conductance (INCV) are implemented using two topologies of DC-DC converters i.e. buck and boost converters. As input variables to the PV systems, recorded irradiance and temperature, and extracted photovoltaic parameters (ideality factor, series resistance and reverse saturation current) were used. The obtained results show that buck converter has a lot of power losses when controlled by each of the four MPPT algorithms. Meanwhile, boost converter presents a stable output power during the whole day. Once more, the results show that INCV algorithm has the best performance.

High step-up quasi-Z-source DC–DC converters with single switched capacitor branch

Aiming to integrate the respective merits of the switched-capacitor converter and the quasi-Z-source converter. An novel high step-up quasi-Z-source DC–DC converter with a single switched-capacitor branch is proposed. Compared to other high boost DC–DC converters,the proposed converter can provide higher output voltage gain, lower current stress across the switches, and lower voltage stress across the output diodes by using the same or similar passive and active components. Therefore, the efficiency and reliability of the converter can be improved.The topological derivation, operating principle, parameter selection, and comparison with other DC–DC converters are presented. Finally, both simulations and experimental results are given to verify the characteristics of the proposed converter.

Digital Control Technologies for DC/DC Switching Converters

An overview of recent advances in digital control of low-to medium-power DC/DC switching converters is presented.Traditionally,analog electronics methods have dominated in controlling such DC/DC converters.However,with the steadily decreasing cost of ICs,the feasibility of digitally controlled DC/DC switching converters has increased sig-nificantly.This paper outlines a sample of digital solutions for DC/DC switching converters to enhance the performance of DC/DC switching converters.Furthermore,latest research activities pertaining to applications for steady-state and dy-namic performance improvement,such as efficiency optimization,controller auto tuning,and capacitor charge balance control,is discussed.These applications demonstrate the significant advantages and potentials of digital control.

Energy Factor and Mathematical Modeling for Power DC/DC Converters

Mathematical modelling for power DC/DC converters is a historical problem accompanying DC/DC conversion technology since 1940’s. The traditional mathematical modelling is not available for complex structure converters since the differential equation order increases very high. We have to search other way to establish mathematical modelling for power DC/DC converters.We have theoretically defined a new concept-Energy Factor （EF） in this paper and researched the relations between EF and the mathematical modelling for power DC/DC converters. EF is a new concept in power DC/DC conversion technology, which thoroughly differs from the traditional concepts such as power factor （PF）, power transfer efficiency （η）, total harmonic distortion （THD） and ripple factor （RF）. EF and the subsequential EFV (and EFVD) can illustrate the system stability, reference response and interference recovery. This investigation is very helpful for system design and DC/DC converters characteristics foreseeing. Two DC/DC converters: Buck converter and Super-Lift Luo-Converter as the samples are analysed in this paper to demonstrate the applications of EF, EFV (and EFVD), PE, SE, VE （and VED）, time constant τ and damping time constant τd.

一种交叉倍压型高增益DC/DC变换器

针对光伏发电、燃料电池发电等领域对高增益直流变换器的需求,以两相交错并联升压变换器为研究对象,由2个含有电感的倍压单元组合设计出实现电压提升的交叉倍压结构,据此提出了一种新颖的交叉倍压型高增益DC/DC变换器。该变换器可实现(3n+4)/(1-d)倍的高电压增益(1∶n为耦合电感匝数比,d为变换器占空比),且具有电路器件的低电压应力特性。对于漏感引起的开关管电压尖峰问题,引入了钳位电容构成释放漏感能量通道,同时提升了输出电压。介绍了新型交叉倍压型高增益变换器的拓扑结构,分析了变换器各模态的工作过程,推导了电压增益、输入电流纹波及各器件电压应力等稳态特性,并搭建样机进行实验研究,验证了该直流变换技术方案的可行性和先进性。

A novel trajectory prediction control for proximate time-optimal digital control DC–DC converters

The purpose of this paper is to present a novel trajectory prediction method for proximate time-optimal digital control DC-DC converters. The control method provides pre-estimations of the duty ratio in the next several switching cycles, so as to compensate the computational time delay of the control loop and increase the control loop bandwidth, thereby improving the response speed. The experiment results show that the fastest transient response time of the digital DC-DC with the proposed prediction is about 8/μs when the load current changes from 0.6 to 0.1A.

单级三相谐波电流注入可升降压AC/DC变换器

为适应电动车充电电压宽范围变化需求,本文针对传统充电桩前级整流器拓扑开展研究,提出一种新式单级三相AC/DC变换器。该变换器集成了三相桥式不控整流电路与Cuk模块,为降低输入侧电流谐波分量,选用双向开关管构建谐波电流回馈通路,整体构造成单级式拓扑结构。文章阐述了变换器的电路结构及工作模态,通过建立变换器的等效模型推导出电压增益。变换器通过简单的控制逻辑即可实现正弦输入电流并拥有高功率因数。最后通过搭建变换器数字控制实验平台验证了所提变换器的可行性。

Design Analysis of DC-DC Converters Connected to a Photovoltaic Generator and Controlled by MPPT for Optimal Energy Transfer throughout a Clear Day

The DC-DC converters are widely used in photovoltaic generating systems as an interface between PV module and the load. These converters must be chosen to be able to match the maximum power point (MPP) of PV module when climatic conditions change with different resistive load values. So DC-DC converters must be used with MPPT controller in order to reduce losses in the global PV system. This article focuses on the effect of climatic conditions on design of two components (inductance, capacitance) for three topologies of DC-DC converters commonly used in PV systems. When climatic conditions change, the boundary of inductance and capacitance parameters of DC-DC converter will change. These two parameters must be properly sized to achieve optimal efficiency for each converter. The design optimization is based on two principles: 1) for a steady-state operation in a continuous conduction mode, the inductance value for all choppers must be greater than the maximum value of boundary inductance, and 2) in order to limit the output voltage ripple of DC-DC converter below a desired value, the filter capacitance must be larger than the maximum value of boundary capacitance.

模块化高压大容量DC/DC变换器综述

随着新能源发电占比增加和电网规模的不断扩大,直流输电系统的容量不断提升,含有不同电压等级的直流电网是未来发展的必然趋势。在此背景下,DC/DC变换器作为直流电网关键设备,在多电压等级互联场景中发挥着重要作用。文中首先对已有的模块化高压大容量DC/DC变换器进行归纳、分类和比较,然后阐述了目前模块化高压大容量DC/DC变换器的拓扑结构、工作原理与特点,并针对其特点提出了不同变换器的适用场景,最后对未来的研究方向提出了建议。

Exact Dynamic Modeling of PWM DC-to-DC Power Converters—Part I: Continuous Conduction Mode

A general approach is presented by which the exact frequency response of any transfer function of switched linear networks can be determined. This is achieved with a describing function approach using a state space equation formulation. This work presents a somewhat simplified set of equations to one previously given by one of the authors. To demonstrate application of the general formulation, the frequency responses of switched networks used as PWM DC-to-DC converters operating in continuous conduction mode (CCM) under voltage mode control are derived. (The accompanying paper, Part II, will present results for converters operating in discontinuous conduction mode (DCM)). From the general sets of equations developed here, both the control to output and input source variation to output frequency responses are derived. The describing function approach enables exact frequency response determination, even at high frequencies where the accuracy using average models may be compromised. Confirmation of the accuracy of the derived models is provided by comparing the responses with those obtained using the commercial simulator PSIM on a PWM boost converter. The magnitude and phase responses are shown to match perfectly over the full range of frequencies up to close to half the switching frequency. Matlab code that implements the models is given such that the user can easily adapt for use with other PWM converter topologies.

Exact Dynamic Modeling of PWM DC-to-DC Power Converters—Part II: Discontinuous Conduction Mode

This paper follows on from the first paper, Part I, where a general formulation of a describing function approach to frequency response determination of switched linear networks, such as PWM converters, was simplified and updated. The models assume a piecewise linear state space equation description of the system and results in a closed form solution for the sought after frequency response. In Part I, model derivation was demonstrated for the case of PWM converters operating in the continuous conduction mode (CCM). This operating mode does not feature any state dependent switching times. In this paper, Part II, frequency response models for any transfer function for PWM converters operating in discontinuous conduction mode (DCM) are derived based on the theory presented in Part I. This operating model features state dependent switching times. The describing function models developed are exact and therefore, in terms of accuracy, are to be preferred over averaged models which are widely used. The example of a boost dc-to-dc converter operating in DCM is simulated to obtain the control to output and input to output frequency responses and are compared with the models derived here. Excellent agreement between the simulated and model responses was found. Matlab code implementing the analytical models is also presented which the user can adapt for any other PWM converter topology. The models derived here may be used as a basis from which simplified models may be derived while still preserving required accuracy.