Modulation bandwidth enhancement in monolithic integrated two-section DFB lasers based on the detuned loading effect

Modulation bandwidth enhancement in a directly modulated two-section distributed feedback(TS-DFB)laser based on a detuned loading effect is investigated and experimentally demonstrated.The results show that the 3-dB bandwidth of the TS-DFB laser is increased to 17.6 GHz and that chirp parameter can be reduced to 2.24.Compared to the absence of a detuned loading effect,there is a 4.6 GHz increase and a 2.45 reduction,respectively.After transmitting a 10 Gb/s non-return-to-zero(NRZ)signal through a 5-km fiber,the modulation eye diagram still achieves a large opening.Eight-channel laser arrays with precise wavelength spacing are fabricated.Each TS-DFB laser in the array has side mode suppression ratios(SMSR)>49.093 dB and the maximum wavelength residual<0.316 nm.

Highly Efficient L-Band Fibre -DFB Lasers

A more than 12 mW highly efficient fibre-DFB laser operating at 1618.3 nm is fabricated and characterised. Its high-power, low-noise and single-polarisation characteristics make it very suitable WDM-source for L-band transmission.

Fabrication of EAM-Integrated DFB Lasers With A Coupling Waveguide

EAM-DFB monolithic light sources with the coupling waveguide between laser and modulator have been developed. 10mw output light power at 90mA and 18dB extinction ratio at -2V has been achieved.

Optical transmitter module with hybrid integration of DFB laser diode and proton-exchanged LiNbO_(3)modulator chip

In this work,a hybrid integrated optical transmitter module was designed and fabricated.A proton-exchanged Mach–Zehnder lithium niobate(LiNbO_(3))modulator chip was chosen to enhance the output extinction ratio.A fiber was used to adjust the rotation of the polarization direction caused by the optical isolator.The whole optical path structure,including the laser chip,lens,fiber,and modulator chip,was simulated to achieve high optical output efficiency.After a series of process improvements,a module with an output extinction ratio of 34 dB and a bandwidth of 20.5 GHz(from 2 GHz)was obtained.The optical output efficiency of the whole module reached approximately 21%.The link performance of the module was also measured.

Electrically and Optically Bistable Operation in an Integration of a 1310 nm DFB Laser and a Tunneling Diode

We experimentally demonstrate an In P-based hybrid integration of a single-mode DFB laser emitting at around 1310 nm and a tunneling diode. The evident negative differential resistance regions are obtained in both electrical and optical output characteristics. The electrical and optical bistabilities controlled by the voltage through the tunneling diode are also measured. When the voltage changes between 1.46 V and 1.66 V, a 200-mV-wide hysteresis loop and an optical power ON/OFF ratio of 17 dB are obtained. A side-mode suppression ratio of the integrated device in the ON state is up to 43 dB. The tunneling diode can switch on/off the laser within a very small voltage range compared with that directly controlled by a voltage source.

Simulations of a Novel All-Optical Flip-Flop Based on a Nonlinear DFB Laser Cavity Using GPGPU Computing

A new all-optical flip-flop based on a nonlinear Distributed feedback (DFB) structure is proposed. The device does not require a holding beam. A nonlinear part of the grating is detuned from the remaining part of the grating and has negative nonlinear coefficient. Optical gain is provided by an injected electrical current into an active layer. In the OFF state, due to the detuned section, no laser light is generated in the device. An injected optical pulse reduces the detuning of the nonlinear section, and the optical feedback provided by the DFB structure generates a laser light in the structure that sustains the change in the detuned section. The device is switched “OFF” by detuning another section of the grating by a Reset pulse. The Reset pulse reduces the refractive index of that section by the generation of electron-hole pairs. The Reset pulse wavelength is adjusted such that the optical gain provided by the active layer at that wavelength is zero. The Reset pulse is prevented from reaching the nonlinear detuned section by introducing an optical absorber in the laser cavity to attenuate the pulse. The device is simulated in time domain using General Purpose Graphics Processing Unit (GPGPU) computing. Set-Reset operations are in nanosecond time scale.

Long-term ultrastable frequency dissemination via a 50-km spooled fiber link using a two-section DFB laser

The stable long-distance transmission of radio-frequency(RF)signals holds significant importance from various aspects,including the comparison of optical frequency standards,remote monitoring and control,scientific research and experiments,and RF spectrum management.We demonstrate a scheme where an ultrastable frequency signal was transmitted over a 50 km coiled fiber.The optical RF signal is generated using a two-section distributed feedback(DFB)laser for direct modulation based on the reconstruction equivalent chirp(REC)technique.The 3-dB modulation bandwidth of the two-section DFB laser is 18 GHz and the residual phase noise of-122.87 dBc/Hz is achieved at 10-Hz offset frequency.We report a short-term stability of 1.62×10^(-14)at an average time of 1 s and a long-term stability of 6.55×10^(-18)at the measurement time of 62,000 s when applying current to the front section of the DFB laser.By applying power to both sections,the stability of the system improves to 4.42×10^(-18)within a testing period of 56,737 s.Despite applying temperature variations to the transmission link,long-term stability of 8.63×10^(-18)at 23.9 h can still be achieved.

A Novel Multisection Distributed Feedback Laser with Varied Ridge Width for Self-Pulsation Generation

A novel ridge-waveguide multisection （MS） distributed feedback （DFB） laser, which consists of two identical DFB sections but different ridge widths, is proposed to generate beating-type self-pulsations （SPs）. The spatiotemporal dynamic response of such a multisection DFB laser is calculated based on a large-signal travelling-wave model. Self-pulsating output at about 150GHz is predicted, and evidences for the beating mechanism of the SPs are provided. To the best of our knowledge, this is the first report on SP generated by MS-DFB lasers with varied ridge width. Compared to other alternatives, such devices are much easier to implement and also enjoy the advantages of lower cost and higher design freedom.

Coupling characteristics of laterally coupled gratings with slots

Laterally-coupled ridge-waveguide distributed feedback lasers fabricated without epitaxial regrowth steps have the advantages of process simplification and low cost.We present a laterally coupled grating with slots.The slots etched between the ridge and grating area are designed to suppress the lateral diffusion of carriers and to reduce the influence of the aspect-ratio-dependent-etching effect on the grating morphology in the etching process.Moreover,the grating height in this structure can be decreased to lower the aspect ratio significantly,which is advantageous over the conventional laterally coupled ridge waveguide gratings.The effects of five main structural parameters on the coupling characteristics of gratings are studied by MODE Solutions.It is found that varying the lateral width of the grating can be used as an effective way to tune the coupling strength;narrow slots(100 nm and 300 nm)and wide ridge(2μm–4μm)promote the stability of grating coupling coefficient and device performance.It is important to note that the grating bottom should be fabricated precisely.The comparative study of carrier distribution and mode field distribution shows that the introduction of narrow slots can strengthen the competitive advantage and stability of the fundamental mode.

Frequency-modulated continuous-wave dual-frequency LIDAR based on a monolithic integrated two-section DFB laser

We demonstrate a high-resolution frequency-modulated continuous-wave dual-frequency LIDAR system based on a monolithic integrated two-section(TS) distributed feedback(DFB) laser. In order to achieve phase locking of the two lasers in the TS-DFB laser, the sideband optical injection locking technique is employed. A high-quality linear frequency-modulated signal is achieved from the TS-DFB laser. Utilizing the proposed LIDAR system, the distance and velocity of a target can be measured accurately. The maximum relative errors of distance and velocity measurement are 1.6% and 3.18%, respectively.

A double wavelength DFB laser with an identical active area for CWDM

A novel distribute feedback (DFB) laser which gave two different wavelengths under two distinct work conditions was fabricated. The laser consists of two Bragg gratings with different periods corresponding to wavelength spacing of 20 nm in an identical active area. When driving current was injected into one of the different sections separately, two different wavelengths at 1542.4 and 1562.5 nm were realized. The side mode suppression ratio (SMSR) of 45 dB or more both for the two Bragg wavelengths were achieved. The fabricating process of the laser was just the samp as that of traditional DFB laser diode. This device can be potentially used in coarse wavelength division multiplexer (CWDM) as a promising light source and the technology idea can be used to enlarge the transmission capacity in metro area network (MAN).

Analysis of a wavelength selectable cascaded DFB laser based on the transfer matrix method

A novel cascaded DFB laser,which consists of two serial gratings to provide selectable wavelengths,is presented and analyzed by the transfer matrix method.In this method,efficient facet reflectivity is derived from the transfer matrix built for each serial section and is then used to simulate the performance of the novel cascaded DFB laser through self-consistently solving the gain equation,the coupled wave equation and the current continuity equations.The simulations prove the feasibility of this kind of wavelength selectable laser and a corresponding designed device with two selectable wavelengths of 1.51μm and 1.53μm is realized by experiments on InP-based multiple quantum well structure.

Stabilized DFB laser system with large tuning range

We propose, design, and realize a compact stabilized laser system that can be tuned within 24 GHz automatically. This laser system consists of two distributed feedback （DFB） lasers, one of which is reference and locked to the D2 line of Rb87, the other laser is a slave that is locked to the reference laser via a loop servo. We measured the frequency of the beating signal of the two lasers and generated an error signal, which controlled the frequency of the slave laser to close the loop. We compressed the fluctuation of the beating signal’s frequency to less than 1 MHz. Furthermore, the system can also automatically determine and control whether the slave is red detuned or blue detuned to the reference. The dimensions of our laser system are about 15 cm×20 cm×10 cm. This kind of laser system can be applied in many important applications, such as atomic interferometer and cold atomic clock.

DFB fiber laser sensor for simultaneous measurement of acoustic and magnetic fields

A novel distributed feedback（DFB） fiber laser sensor, which can measure acoustic and magnetic fields simultaneously, is proposed. The magnetic field can be measured by detecting the change of resonant frequency of the fiber laser, and the acoustic pressure can be measured by detecting the phase shift of the fiber laser. Both of the signals can be simultaneously demodulated in the frequency domain without affecting each other. Experimental studies show that the acoustic pressure sensitivity of this sensor is about-130 d B（0 dB re 1 pm∕μPa） and the sensor has a good linearity with a magnetic field sensitivity of 0.57 Hz∕mT.

A Coal Mine Multi-Point Fiber Ethylene Gas Concentration Sensor

Spontaneous combustion of the coal mine goaf is one of the main disasters in the coal mine. The detection technology based on symbolic gas is the main means to realize the spontaneous combustion prediction of the coal mine goaf, and ethylene gas is an important symbol gas of spontaneous combustion in the coal accelerated oxidation stage. In order to overcome the problem of current coal ethylene detection, the paper presents a mine optical fiber multi-point ethylene concentration sensor based on the tunable diode laser absorption spectroscopy. Based on the experiments and analysis of the near-infrared spectrum of ethylene, the system employed the 1.62 μm （DFB） wavelength fiber coupled distributed feedback laser as the light source. By using the wavelength scanning technique and developing a stable fiber coupled Herriot type long path gas absorption cell, a ppm-level high sensitivity detecting system for the concentration of ethylene gas was realized, which could meet the needs of coal mine fire prevention goaf prediction.

A 1.55-μm laser array monolithically integrated with an MMI combiner

The monolithic integration of four 1.55-μm range InGaAsP/InP distributed feedback lasers with a 4× 1 multimode-interference （MMI） optical combiner using the varied width ridge method is proposed and demonstrated. The average output power is 1.5 mW when the current of LD is 100 mA and the threshold current is 30-35 mA at 25 ℃. The lasing wavelength is 1.55-μm range and 40 dB sidemode suppression ratio is obtained. The four channels can operate separately or simultaneously.