Drying is a complicated physical process which involves simultaneous heat and mass transfer in the removal of solvents inside propellants.Inappropriate drying techniques may result in the formation of a hard skin laye...Drying is a complicated physical process which involves simultaneous heat and mass transfer in the removal of solvents inside propellants.Inappropriate drying techniques may result in the formation of a hard skin layer near the surface to block the free access of most solvent through for long stick propellants with large web thickness,which lead to lower drying efficiency and worse drying quality.This study aims to gain a comprehensive understanding of drying process and clarify the mechanism of the blocked layer near the propellant surface.A new three-dimensional coupled heat and mass transfer(3D-CHMT)model was successfully developed under transient conditions.The drying experiment results show that the 3DCHMT model could be applied to describe the drying process well since the relative error of the content of solvent between simulation and experiment values is only 5.5%.The solvent behavior simulation demonstrates that the mass transfer process can be divided into super-fast(SF)and subsequent minorfast(MF)stages,and the SF stage is vital to the prevention of the blocked layer against the free access for solvent molecules inside propellant grains.The effective solvent diffusion coefficient(Deff)of the propellant surface initially increases from 3.4×10^(-6)to 5.3×10^(-6)m^(2)/s as the temperature increases,and then decreases to 4.1×10^(-8)m^(2)/s at 60-100 min.The value of Deffof surface between 0-1.4 mm has a unique trend of change compared with other regions,and it is much lower than that of the internal at100 min under simulation conditions.Meanwhile,the temperature of the propellant surface increases rapidly at the SF stage(0-100 min)and then very slowly thereafter.Both the evolution of Deffand temperature distribution demonstrate that the blocked layer near the propellant surface has been formed in the time period of approximately 0-100 min and its thickness is about 1.4 mm.To mitigate the formation of blocked layer and improve its drying quality of finial propellant products effectively,it should be initially dried at lower drying temperature(30-40℃)in 0-100 min and then dried at higher drying temperature(50-60℃)to reduce drying time for later drying process in double base gun propellants.The present results can provide theoretical guidance for drying process and optimization of drying parameters for long stick propellants with large web thickness.展开更多
A systematic method was developed for ice-class propeller modeling,performance estimation,strength and integrity evaluation and optimization.To estimate the impact of sea ice on the propeller structure,URI3 rules,esta...A systematic method was developed for ice-class propeller modeling,performance estimation,strength and integrity evaluation and optimization.To estimate the impact of sea ice on the propeller structure,URI3 rules,established by the International Association of Classification Societies in 2007,were applied for ice loading calculations.An R-class propeller(a type of ice-class propeller)was utilized for subsequent investigations.The propeller modeling was simplified based on a conventional method,which expedited the model building process.The propeller performance was simulated using the computational fluid dynamics(CFD)method.The simulation results were validated by comparison with experimental data.Furthermore,the hydrodynamic pressure was transferred into a finite element analysis(FEA)module for strength assessment of ice-class propellers.According to URI3 rules,the ice loading was estimated based on different polar classes and working cases.Then,the FEA method was utilized to evaluate the propeller strength.The validation showed that the simulation results accorded with recent research results.Finally,an improved optimization method was developed to save the propeller constituent materials.The optimized propeller example had a minimum safety factor of 1.55,satisfying the safety factor requirement of≥1.5,and reduced the design volume to 88.2%of the original.展开更多
基金supported by the National Natural Science Foundation of China(Grant No.22075146)。
文摘Drying is a complicated physical process which involves simultaneous heat and mass transfer in the removal of solvents inside propellants.Inappropriate drying techniques may result in the formation of a hard skin layer near the surface to block the free access of most solvent through for long stick propellants with large web thickness,which lead to lower drying efficiency and worse drying quality.This study aims to gain a comprehensive understanding of drying process and clarify the mechanism of the blocked layer near the propellant surface.A new three-dimensional coupled heat and mass transfer(3D-CHMT)model was successfully developed under transient conditions.The drying experiment results show that the 3DCHMT model could be applied to describe the drying process well since the relative error of the content of solvent between simulation and experiment values is only 5.5%.The solvent behavior simulation demonstrates that the mass transfer process can be divided into super-fast(SF)and subsequent minorfast(MF)stages,and the SF stage is vital to the prevention of the blocked layer against the free access for solvent molecules inside propellant grains.The effective solvent diffusion coefficient(Deff)of the propellant surface initially increases from 3.4×10^(-6)to 5.3×10^(-6)m^(2)/s as the temperature increases,and then decreases to 4.1×10^(-8)m^(2)/s at 60-100 min.The value of Deffof surface between 0-1.4 mm has a unique trend of change compared with other regions,and it is much lower than that of the internal at100 min under simulation conditions.Meanwhile,the temperature of the propellant surface increases rapidly at the SF stage(0-100 min)and then very slowly thereafter.Both the evolution of Deffand temperature distribution demonstrate that the blocked layer near the propellant surface has been formed in the time period of approximately 0-100 min and its thickness is about 1.4 mm.To mitigate the formation of blocked layer and improve its drying quality of finial propellant products effectively,it should be initially dried at lower drying temperature(30-40℃)in 0-100 min and then dried at higher drying temperature(50-60℃)to reduce drying time for later drying process in double base gun propellants.The present results can provide theoretical guidance for drying process and optimization of drying parameters for long stick propellants with large web thickness.
基金The author would like to thank University of Tasmania and Newcastle University for their support。
文摘A systematic method was developed for ice-class propeller modeling,performance estimation,strength and integrity evaluation and optimization.To estimate the impact of sea ice on the propeller structure,URI3 rules,established by the International Association of Classification Societies in 2007,were applied for ice loading calculations.An R-class propeller(a type of ice-class propeller)was utilized for subsequent investigations.The propeller modeling was simplified based on a conventional method,which expedited the model building process.The propeller performance was simulated using the computational fluid dynamics(CFD)method.The simulation results were validated by comparison with experimental data.Furthermore,the hydrodynamic pressure was transferred into a finite element analysis(FEA)module for strength assessment of ice-class propellers.According to URI3 rules,the ice loading was estimated based on different polar classes and working cases.Then,the FEA method was utilized to evaluate the propeller strength.The validation showed that the simulation results accorded with recent research results.Finally,an improved optimization method was developed to save the propeller constituent materials.The optimized propeller example had a minimum safety factor of 1.55,satisfying the safety factor requirement of≥1.5,and reduced the design volume to 88.2%of the original.
