A time domain induced polarization relaxation time spectrum inversion method based on a damping factor and residual correction

Relaxation time spectra （RTS） derived from time domain induced polarization data （TDIP） are helpful to assess oil reservoir pore structures. However, due to the sensitivity to the signal-to-noise ratio （SNR）, the inversion accuracy of the traditional singular value decomposition （SVD） inversion method reduces with a decrease of SNR. In order to enhance the inversion accuracy and improve robustness of the inversion method to the SNR, an improved inversion method, based on damping factor and spectrum component residual correction, is proposed in this study. The numerical inversion results show that the oscillation of the RTS derived from the SVD method increased with a decrease of SNR, which makes it impossible to get accurate inversion components. However, the SNR has little influence on inversion components of the improved method, and the RTS has high inversion accuracy and robustness. Moreover, RTS derived from core sample data is basically in accord with the pore-size distribution curve, and the RTS derived from the actual induced polarization logging data is smooth and continuous, which indicates that the improved method is practicable.

Broad-Band FMR Linewidth of Co_2MnSi Thin Films with Low Damping Factor:The Role of Two-Magnon Scattering

The low Gilbert damping factor, which is usually measured by ferromagnetic resonance, is crucial in spintronic applications. Two-magnon scattering occurs when the orthogonMity of the ferromagnetic resonance mode and other degenerate spin wave modes was broken by magnetic anisotropy, voids, second phase, surface defects, etc., which is important in analysis of ferromagnetic resonance linewidth. Direct fitting to linewidth with Gilbert damping is advisable only when the measured linewidth is a linear function of measuring frequency in a broad band measurement. We observe the nonlinear ferromagnetic resonance linewidth of Co2MnSi thin films with respect to measuring frequency in broad band measurement. Experimental data could be well fitted with the model including two-magnon scattering with no fixed parameters. The fitting results show that two-magnon scattering results in the nonlinear linewidth behavior, and the Gilbert damping factor is much smaller than reported ones, indicating that our Co2MnSi films are more suitable for the applications of spin transfer torque.

Damping Factor Estimation of a Flexible-Matrix-Composite Body Pump

Two very important factors which determine the effectiveness of a pump are its volumetric and power efficiencies. Yin and Ghoneim constructed a prototype of a Flexible-Matrix-Composite (FMC) body pump with a very high volumetric efficiency or pumping potential (the relative volume reduction due to a relative input stroke). The high volumetric efficiency is attributed to the geometry of the pump’s structure (hyperboloid) as well as the high negative effective Poisson’s ratio of the 3-layer [θ/β/θ] flexible-matrix-composite (carbon/polyurethane) laminate adopted for the body of the pump. However, the power efficiency of the pump was not evaluated. It is the objective of the current paper to obtain an estimate of the power efficiency of the pump. The viscoelastic properties of the 3-layer FMC (carbon/polyurethane) laminate are evaluated experimentally using the Dynamic Mechanical Analyzer (DMA) as well as analytically by applying the correspondence principle together with the micro-mechanics approach. In order to obtain an estimate of the power efficiency of the FMC body pump, the axial and shear loss factors of a laminated infinitely long cylindrical tube as functions of β and θ fiber orientation angles are determined employing the Adam and Bacon approach. The analysis engenders high loss factors (greater than 0.4), which suggests that the power efficiency of the proposed pump using the 3-layer carbon/polyurethane laminate may be low.

Rational design of thermoelastic damping in microresonators with phase-lagging heat conduction law

The design of thermoelastic damping(TED)affected by the phase-lagging non-Fourier heat conduction effects becomes significant but challenging for enlarging the quality factor of widely-used microresonators operating in extreme situations,including ultra-high excitation frequency and ultra-low working temperature.However,there does not exist a rational method for designing the TED in the framework of non-Fourier heat conduction law.This work,therefore,proposes a design framework to achieve low thermoelastic dissipation of microresonators governed by the phase-lagging heat conduction law.The equation of motion and the heat conduction equation for phase-lagging TED microresonators are derived first,and then the non-Fourier TED design problem is proposed.A topology optimization-based rational design method is used to resolve the design problem.What is more,a two-dimensional(2D)plain-strain-based finite element method(FEM)is developed as a solver for the topology optimization process.Based on the suggested rational design technique,numerical instances with various phase lags are investigated.The results show that the proposed design method can remarkably reduce the dissipation of microresonators by tailoring their substructures.

High frequency characteristics of (Ni_(75)Fe_2)_x(Zn O)_(1-x) granular thin films with tunable damping coefficient

The effect of the volume fraction of ferromagnetic metal （x） in （Ni75Fe25）x（ZnO）1-x nanogranular thin films on microstructural, soft-magnetic, and high-frequency properties was investigated. Good soft-magnetic properties were obtained in a broad x range, with 0.55 〈 x 〈 0.82. High resolution transmission electron microscopy （HRTEM） observations reveal that the grain size of the samples is lower than 14 nm, and that it decreases with decreasing x. Of special interest, our investigation of the permeability spectra indicates that these films exhibit an adjustable frequency linewidth of resonance peak, dependant upon changing x. Correspondingly, large and adjustable damping coefficients （aeff） from 0.023 to 0.043 were achieved by decreasing x from 0.82 to 0.55. Combined with the HRTEM results, the variation of αeff with x was analyzed in detail.

THE AUTO-ADJUSTABLE DAMPING METHOD FORSOLVING NONLINEAR EQUATIONS

The general approach for solving the nonlinear equations is linearizing the equations and forming various iterative procedures, then executing the numerical simulation. For the strongly nonlinear problems, the solution obtained in the iterative process is always difficult, even divergent due to the numerical instability. It can not fulfill the engineering requirements. Newton's method and its variants can not settle this problem. As a result, the application of numerical simulation for the strongly nonlinear problems is limited. An auto-adjustable damping method has been presented in this paper. This is a further improvement of Newton's method with damping factor. A set of vector of damping factor is introduced. This set of vector can be adjusted continuously during the iterative process in accordance with the judgement and adjustment. An effective convergence coefficient and quichening coefficient are employed to relax the restricted requirements for the initial values and to shorten the iterative process. Then, the numerical stability will be ensured for the solution of complicated strongly nonlinear equations. Using this method, some complicated strongly nonlinear heat transfer problems in airplanes and aeroengines have been numerically simulated successfully. It can be used for the numerical simulation of strongly nonlinear problems in engineering such as nonlinear hydrodynamics and aerodynamics, heat transfer and structural dynamic response etc.

Hygrothermal Study of a House Made of Local Biosourced Materials Based on Clay: Experimental Study

The purpose of this study is to experimentally analyze the thermal behavior of the walls of a prototype experimental house. A Datalogger and thermocouples were used on the experimental house to determine the temperatures of the exterior and interior walls. Also, “MSR” type HygroPuce was used to determine the exterior and interior temperatures and relative humidity of the habitat. The results show that a wall made of bio-based materials with a mixture of “earth + Hibiscus cannabinus L. fibers” allows reducing the fluctuations of the interior temperatures. We observe the peaks of temperatures on the external walls at 11:00 am and for the interior walls, the peaks are observed at 5:00 pm. The maximum thermal phase shift between the peaks of the external and internal temperatures is about 7.5 hours, and the maximum damping factor is 0.9. Also, we note that the thermal performance of the material used in the design of the envelope of the house is determined by the improvement of the response of the envelope in front of the external thermal solicitations.

The Effect of Fibre Length on Flexural and Dynamic Mechanical Properties of Pineapple Leaf Fibre Composites

The present paper deals with the effect of loading different pineapple leaf fibre(PALF)length(short,mixed and long fibres)and their reinforcement for the fabrication of vinyl ester(VE)composites.Performance of PALF/VE composites was investigated through three-point bending flexural testing and viscoelastic(dynamic)mechanical properties through dynamic mechanical analysis(DMA).DMA results revealed that the long PALF/VE composites displayed better mechanical,damping factor and dynamic properties as compared to the short and mixed PALF/VE composites.The flexural strength and modulus of long PALF/VE composites were 113.5 MPa and 14.3 GPa,respectively.The storage(E′)and loss(E″)moduli increased to 2000 MPa and 225 MPa respectively for PALF/VE composites.Overall result analysis indicated that increasing the length of the reinforcement fibre results in satisfactory mechanical performance and dynamic properties of composites.

Reinforcing Effect of Organo-Modified Fillers in Rubber Composites as Evidenced from DMA Studies

The use of organically enhanced kaolin clay as reinforcing filler for NR(natural rubber)and blends of NR with NBR(nitrile-butadiene rubber)and poly BR(butadiene rubber)system were investigated on the basis of DMA(dynamic mechanical analysis).Kaolin clay was modified using a chemical complex of HH(hydrazine hydrate)and SRSO(sodium salt of rubber seed oil).Intercalation of SRSO into kaolin under optimized condition showed an inter-lamellar layer expansion to 4.668 nm,compared to the characteristic d001 XRD(X-ray diffraction)peak of pristine kaolin at 0.714 nm.The morphology,visco-elastic behavior,modulus property,polymer miscibility and Tg(glass transition temperature)of nano-kaolin filled NR and its blend with synthetic rubbers have been studied in detail.DMA showed a diminution in tanδpeak height and a modulus shift in correspondence with increased CLD(crosslink density).Pure NR shows only~1%increase in storage modulus(E′)while adding nanoclay rather than micron sized pristine clay under experimental conditions,because of the feeble interaction between filler and matrix,as compared to blend.An increment of~76%and~117%in E′was recognized by the addition of 4 wt%nanoclay in blends such as BR mK and NBR mK.With loss modulus(E″)pure NR shows only~7%decrease while adding nanoclay,compared to blend.A decrement of~54%and~55%in E″by the addition of 4 wt%nanoclay in BR mK and NBR mK blends were observed.As a whole,DMA was performed to figure out the effect of surface modification enabling to materialize composite.

Corrected Statistical Energy Analysis Model in a Non-Reverberant Acoustic Space

Statistical Energy Analysis(SEA)is a well-known method to analyze the flow of acoustic and vibration energy in a complex structure.This study investigates the application of the corrected SEA model in a non-reverberant acoustic space where the direct field component from the sound source dominates the total sound field rather than a diffuse field in a reverberant space which the classical SEA model assumption is based on.A corrected SEA model is proposed where the direct field component in the energy is removed and the power injected in the subsystem considers only the remaining power after the loss at first reflection.Measurement was conducted in a box divided into two rooms separated by a partition with an opening where the condition of reverberant and non-reverberant can conveniently be controlled.In the case of a non-reverberant space where acoustic material was installed inside the wall of the experimental box,the signals are corrected by eliminating the direct field component in the measured impulse response.Using the corrected SEA model,comparison of the coupling loss factor(CLF)and damping loss factor(DLF)with the theory shows good agreement.

Numerical evaluation of acoustic characteristics and their damping of a thrust chamber using a constant-volume bomb model

In order to numerically evaluate the acoustic characteristics of liquid rocket engine thrust chambers by means of a computational fluid dynamics method, a mathematical model of an artificial constant-volume bomb is proposed in this paper. A localized pressure pulse with a very high amplitude can be imposed on specified regions in a combustion chamber, the numerical procedure of which is described. Pressure oscillations actuated by the released constant-volume bomb can then be analyzed via Fast Fourier Transformation（FFT）, and their modes can be identified according to the theoretical acoustic eigenfrequencies of the thrust chamber. The damping performances of the corresponding acoustic modes are evaluated by the half-power bandwidth method. The predicted acoustic characteristics and their damping for a special engine combustor agree well with the experimental data, validating the mathematical model and its numerical procedures. A small-thrust liquid rocket engine chamber is then analyzed by the present model. The First Longitudinal（1L） acoustic mode can be excited easily and is hard to be damped. The axial position of the central constantvolume bomb has little influence on the amplitude and damping capacity of the First Radial（1R） and 1L acoustic modes. Tangential acoustic modes can only be triggered by an off-centered constant-volume bomb, among which the First Tangential（1T） mode is the strongest and regarded as the most harmful one. The amplitude of the 1L acoustic mode is smaller, but its damping factor is larger, as a constant-volume bomb is imposed approaching the injector face. These results are contributed to evaluate the acoustic characteristics and their damping of the combustion chamber.

An Impedance-based Parameter Design Method for Active Damping of Load Converter Station in MTDC Distribution System

To achieve the efficient application of impedance analysis in the stability assessment and enhancement of multiterminal DC distribution systems, this paper proposes the DCside reduced-order impedance models with power control and AC voltage control, respectively, by taking the load converter station as the object. By using the DC-side current as the feedforward state, the active compensator applied to the load converter station with two control modes is also derived as well as the corresponding reduced-order impedance models. Combined with the reduced-order impedance models, a method based on damping factor sensitivity is further proposed to design the parameters of the derived active compensators. The verification results in the frequency domain and time domain demonstrate the accuracy of the reduced-order impedance and the effectiveness of the proposed compensator parameter design method.

FREE VIBRATION ANALYSIS OF SIMPLY SUPPORTED BEAM WITH BREATHING CRACK USING PERTURBATION METHOD

In this paper, a new analytical method for vibration analysis of a cracked simply supported beam is investigated. By considering a nonlinear model for the fatigue crack, the governing equation of motion of the cracked beam is solved using perturbation method. The solution of the governing equation reveals the superhaxmonics of the fundamental frequency due to the nonlinear effects in the dynamic response of the cracked beam. Furthermore, considering such a solution, an explicit expression is also derived for the system damping changes due to the changes in the crack parameters, geometric dimensions and mechanical properties of the cracked beam. The results show that an increase in the crack severity and approaching the crack location to the middle of the beam increase the system damping. In order to validate the results, changes in the fundamental frequency ratios against the fatigue crack severities are compared with those of experimental results available in the literature. Also, a comparison is made between the free response of the cracked beam with a given crack depth and location obtained by the proposed analytical solution and that of the numerical method. The results of the proposed method agree with the experimental and numerical results.

Control of UPQC Based on Steady State Linear Kalman Filter for Compensation of Power Quality Problems

A frequency lock loop(FLL)based steady state linear Kalman filter(SSLKF)for unified power quality conditioner(UPQC)control in three-phase systems is introduced.The SSLKF provides a highly accurate and fast estimation of grid frequency and the fundamental components(FCs)of the input signals.The Kalman filter is designed using an optimized filtering technique and intrinsic adaptive bandwidth architecture,and is easily integrated into a multiple model system.Therefore,the Kalman state estimator is fast and simple.The fundamental positive sequence components(FPSCs)of the grid voltages in a UPQC system are estimated via these SSLKF-FLL based filters.The estimation of reference signals for a UPQC controller is based on these FPSCs.Therefore,both active filters of a UPQC can perform one and more functions towards improving power quality in a distribution network.In addition to the SSLKF-FLL based algorithm,a bat optimization algorithm(based on the echolocation phenomenon of bats)is implemented to estimate the value of the proportional integral(PI)controller gains.The bat algorithm has a tendency to automatically zoom into a region where a promising alternative solution occurs,preventing the solution from becoming trapped in a local minima.The complete three-phase UPQC is simulated in the Matlab/Simulink platform and the hardware is tested under various power quality problems.

Research Progress on Prevention and Treatment of Glucolipid Metabolic Disease with Integrated Traditional Chinese and Western Medicine

Hyperlipidemia, type 2 diabetes mellitus, nonalcoholic fatty liver and many other metabolic disorder are frequently co-existing in patients. In addition, these diseases are closely related in pathophysiological settings. However, increasing of the disease incidence, lacking of comprehensive prevention and control measurements against the key pathology point concomitant occurrence with the pattem of the single disease, single target therapy, that is leading therapeutic strategy for these metabolic disorders in the setting of Western medicine （WM）. On the basis of the combination of the advantages of integrated Chinese medicine （CM） and WM, with unified understanding of such diseases, the new concept of glucolipid metabolic disease （GLMD） is introduced. In this new concept, disorders in glucose and lipid metabolism are recognized as the key trigger and major driving force for the progress of GLMD. The key points of pathology included dysfunction of neuronal-endocrine-immune system,insulin resistance, oxidative stress, inflammation and intestinal flora imbalance. In the core pathogenic perspective of CM, it can be explained as ＂Gan （Liver） Shi Shu Xie＂ （dysfunction of Gan in metabolism and emotion regulation） that will lead to the occurence/production of endogenous dampness and phlegm, blood stasis and turbid. This leads to the new concept of ＂Liver-based regulatory system for metabolic homeostasis＂ to be introduced further. The comprehensive prevention and control strategy ＂Tiao Gan Qi Shu Hua Zhuo＂ （modulating Gan, trigging key metabolic system to resolve pathogenic factors such as phlegm retention and dampness）. Its representative formula Fufang Zhenzhu Tiaozhi Capsule （复方贞术调脂胶囊） is innovated under such rationales. Comment for some commonly-used CM GLMD therapeutic drugs was presented. High-level evidence-based and epidemiological and mechanism studies should be carded out to further interpret and explain of the scientific connotation of GLMD.