Anisotropic strength,deformation and failure of gneiss granite under high stress and temperature coupled true triaxial compression

The anisotropic mechanical behavior of rocks under high-stress and high-temperature coupled conditions is crucial for analyzing the stability of surrounding rocks in deep underground engineering.This paper is devoted to studying the anisotropic strength,deformation and failure behavior of gneiss granite from the deep boreholes of a railway tunnel that suffers from high tectonic stress and ground temperature in the eastern tectonic knot in the Tibet Plateau.High-temperature true triaxial compression tests are performed on the samples using a self-developed testing device with five different loading directions and three temperature values that are representative of the geological conditions of the deep underground tunnels in the region.Effect of temperature and loading direction on the strength,elastic modulus,Poisson’s ratio,and failure mode are analyzed.The method for quantitative identification of anisotropic failure is also proposed.The anisotropic mechanical behaviors of the gneiss granite are very sensitive to the changes in loading direction and temperature under true triaxial compression,and the high temperature seems to weaken the inherent anisotropy and stress-induced deformation anisotropy.The strength and deformation show obvious thermal degradation at 200℃due to the weakening of friction between failure surfaces and the transition of the failure pattern in rock grains.In the range of 25℃ 200℃,the failure is mainly governed by the loading direction due to the inherent anisotropy.This study is helpful to the in-depth understanding of the thermal-mechanical behavior of anisotropic rocks in deep underground projects.

Effect of Plastic Deformation and H_2S on Dynamic Fracture Toughness of High Strength Casing Steel

The effects of plastic deformation and H2 S on fracture toughness of high strength casing steel（C110 steel） were investigated. The studied casing specimens are as follows： original casing, plastic deformation（PD） casing and PD casing after being immersed in NACE A solution saturated with H2S（PD＋H2S）. Instrumented impact method was employed to evaluate the impact behaviors of the specimens, meanwhile, dynamic fracture toughness（JId） was calculated by using Rice model and Schindler model. The experimental results show that dynamic fracture toughness of the casing decreases after plastic deformation. Compared with that of the original casing and PD casing, the dynamic fracture toughness decreases further when the PD casing immersed in H2 S, moreover, there are ridge-shaped feature and many secondary cracks present on the fracture surface of the specimens. Impact fracture mechanism of the casing is proposed as follows： the plastic deformation results in the increase of defect density of materials where the atomic hydrogen can accumulate in reversible or irreversible traps and even recombine to form molecular hydrogen, subsequently, the casing material toughness decreases greatly.

Numerical evaluation of strength and deformability of fractured rocks

Knowledge of the strength and deformability of fractured rocks is important for design, construction and stability evaluation of slopes, foundations and underground excavations in civil and mining engineering. However, laboratory tests of intact rock samples cannot provide information about the strength and deformation behaviors of fractured rock masses that include many fractures of varying sizes, orientations and locations. On the other hand, large-scale in situ tests of fractured rock masses are economically costly and often not practical in reality at present. Therefore, numerical modeling becomes necessary. Numerical predicting using discrete element methods(DEM) is a suitable approach for such modeling because of their advantages of explicit representations of both fractures system geometry and their constitutive behaviors of fractures, besides that of intact rock matrix. In this study, to generically determine the compressive strength of fractured rock masses, a series of numerical experiments were performed on two-dimensional discrete fracture network models based on the realistic geometrical and mechanical data of fracture systems from feld mapping. We used the UDEC code and a numerical servo-controlled program for controlling the progressive compressive loading process to avoid sudden violent failure of the models. The two loading conditions applied are similar to the standard laboratory testing for intact rock samples in order to check possible differences caused by such loading conditions. Numerical results show that the strength of fractured rocks increases with the increasing confning pressure, and that deformation behavior of fractured rocks follows elasto-plastic model with a trend of strain hardening. The stresses and strains obtained from these numerical experiments were used to ft the well-known Mohr-Coulomb(MC) and Hoek-Brown(H-B) failure criteria, represented by equivalent material properties defning these two criteria. The results show that both criteria can provide fair estimates of the compressive strengths for all tested numerical models. Parameters of the elastic deformability of fractured models during elastic deformation stages were also evaluated, and represented as equivalent Young’s modulus and Poisson’s ratio as functions of lateral confning pressure. It is the frst time that such systematic numerical predicting for strength of fractured rocks was performed considering different loading conditions, with important fndings for different behaviors of fractured rock masses, compared with testing intact rock samples under similar loading conditions.

Anisotropy of strength and deformability of fractured rocks

Anisotropy of the strength and deformation behaviors of fractured rock masses is a crucial issue for design and stability assessments of rock engineering structures, due mainly to the non-uniform and non- regular geometries of the fracture systems. However, no adequate efforts have been made to study this issue due to the current practical impossibility of laboratory tests with samples of large volumes con- taining many fractures, and the difficulty for controlling reliable initial and boundary conditions for large-scale in situ tests. Therefore, a reliable numerical predicting approach for evaluating anisotropy of fractured rock masses is needed. The objective of this study is to systematically investigate anisotropy of strength and deformability of fractured rocks, which has not been conducted in the past, using a nu- merical modeling method. A series of realistic two-dimensional （2D） discrete fracture network （DFN） models were established based on site investigation data, which were then loaded in different directions, using the code UDEC of discrete element method （DEM）, with changing confining pressures. Numerical results show that strength envelopes and elastic deformability parameters of tested numerical models are significantly anisotropic, and vary with changing axial loading and confining pressures. The results indicate that for design and safety assessments of rock engineering projects, the directional variations of strength and deformability of the fractured rock mass concerned must be treated properly with respect to the directions of in situ stresses. Traditional practice for simply positioning axial orientation of tunnels in association with principal stress directions only may not be adequate for safety requirements. Outstanding issues of the present study and su^zestions for future study are also oresented.

Experimental and numerical study of coal-rock bimaterial composite bodies under triaxial compression

To accurately predict coal burst hazards and estimate the failure of coal pillars in underground coal mining systems,it is of great significance to understand the mechanical behavior of coal-rock bimaterial composite structures.This paper presents experimental and numerical investigations on the response of rock-coal,coal-rock,and rock-coal-rock bimaterial composite structures under triaxial compression.The triaxial compression experiments are conducted under confining pressures in the range of 0-20 MPa.The resulting inside fracture networks are detected using X-ray-based computed tomography(CT).The experimentally observed data indicate that the mechanical parameters of the rock-coalrock composites are superior to those of the rock-coal and coal-rock combinations.After compression failure,the coal-rock combination specimens are analyzed via X-ray CT.The results display that the failure of the coal-rock composite bodies primarily takes place within the coal.Further,the bursting proneness is reduced by increasing confining pressure.Subsequently,the corresponding numerical simulations of the experiments are carried out by using the particle flow code.The numerical results reveal that coal is vulnerable with regard to energy storage and accumulation.

Structural Research on Embedment of a Bare Deflated Spiral Case

Complete bearing spiral case has not been applied to large power stations in China so far. The proposal of applying complete bearing spiral case necessitates an analysis of the reliability of the spiral case structure and the security of units under various working conditions. In combination with practice of a project, this paper presents a three-dimensional nonlinear finite element static analysis of the concrete using a concrete smeared crack model by means of the well-known finite element method （FEM） software ABAQUS. The stress distribution of the spiral case and reinforcing bars, the range of damages in surrounding concrete, and the displacement of structure are quantified. The computational results indicate that the embedment method ensures the structure＇s safety in strength. At the same time, the result shows that this embedment is a kind of preponderant method for embedment in aspects of economy and technique of construction, and the application of this embedment method to the hydropower station is feasible provided that some proper engineering measures are taken to constrain the width of the concrete in accord with the code＇s requirements. The paper proves the security and reliability of the structural design of spiral case in hydropower station accordingly.

Strength and Deformation of Axially Loaded Fiber-Reinforced Polymer Sheet Confined Concrete Columns

Experimental results of 29 axially loaded fiber-reinforced polymer sheet (FS) confined concrete columns and two reference plain concrete columns are introduced. Twenty four column specimens were confined with carbon fiber sheet (CFS) and five column specimens were hybrid confined with both CFS and glass fiber sheet (GFS). The influence of aspect ratio, FS material, initial axial force ratio, and FS confine-ment degree on the strength and deformation of columns were studied. Based on the experimental results, the equations of complete stress-strain curve of CFS confined concrete are proposed. These equations are suitable for the nonlinear analysis of square and rectangular section columns. Suggestions of applying FS to confine concrete columns are presented.

Bimodal microstructure – A feasible strategy for high-strength and ductile metallic materials

Introducing a bimodal grain-size distribution has been demonstrated an efficient strategy for fabricating high-strength and ductile metallic materials, where fine grains provide strength, while coarse grains enable strain hardening and hence decent ductility. Over the last decades, research activities in this area have grown enormously, including interesting results onfcc Cu, Ni and Al-Mg alloys as well as steel and Fe alloys via various thermo-mechanical processing approaches. However, investigations on bimodal Mg and other hcp metals are relatively few. A brief overview of the available approaches based on thermo- mechanical processing technology in producing bimodal microstructure for various metallic materials is given, along with a summary of unusual mechanical properties achievable by bimodality, where focus is placed on the microstructure-mechanical properties and relevant mechanisms. In addition, key factors that influencing bimodal strategies, such as compositions of starting materials and processing parameters, together with the challenges this research area facing, are identified and discussed briefly.