Lithium(Li)metal is regarded as one of the most promising anode candidates for next-generation batteries due to its extremely high specific capacity and low redox potential.However,its application is still hindered by...Lithium(Li)metal is regarded as one of the most promising anode candidates for next-generation batteries due to its extremely high specific capacity and low redox potential.However,its application is still hindered by the uncontrolled growth of dendritic Li and huge volume fluctuation during cycles.To address these issues,flexible and self-supporting three-dimensional(3D)interlaced Ndoped carbon nanofibers(NCNFs)coated with uniformly distributed 2D ultrathin NiCo_(2)S_(4)nanosheets(denoted CNCS)were designed to eliminate the intrinsic hotspots for Li deposition.Physicochemical dual effects of CNCS arise from limited surface Li diffusivity with a higher Li affinity,leading to uniform Li nucleation and less random accumulation of Li,as confirmed by ab initio molecular dynamics simulations.Due to the unique structure,exchange current density is reduced significantly and metallic Li is further contained within the interspace between the NCNF and NiCo_(2)S_(4)nanosheets,preventing the formation of dendritic Li.The symmetric cell with a Li/CNCS composite anode shows a long-running lifespan for almost 1200 h,with an exceptionally low and stable overpotential under 1mA cm^(-2)/1 mAh cm^(-2).A full cell coupled with a LiFePO4 cathode at a low N/P ratio of 2.45 shows typical voltage profiles but more significantly enhanced performance than that of a LiFePO4 cathode coupled with a bare Li anode.展开更多
In this paper,we consider a new spectrum sharing scenario for a cognitive relay network,where a secondary unmanned aerial vehicle(UAV)relay receives information from the ground secondary base station(SBS)and transmits...In this paper,we consider a new spectrum sharing scenario for a cognitive relay network,where a secondary unmanned aerial vehicle(UAV)relay receives information from the ground secondary base station(SBS)and transmits information to the ground secondary user(SU),coexisting with the primary users(PUs)at the same wireless frequency band.We investigate the optimization of the UAV relay’s three-dimensional(3D)trajectory to improve the communication throughput performance of the secondary network subject to the interference constraints of the PUs.The information throughput maximization problem is studied by jointly optimizing the UAV relay’s 3D trajectory and the transmit power of the SBS and the UAV,subject to the constraints on the velocity and elevation of the UAV relay,the maximum and average transmit power,and the information causality,as well as a set of interference temperature(IT)constraints.An efficient algorithm is proposed to solve the admittedly challenging non-convex problem by using the path discretization technique,the successive convex approximation technique and the alternating optimization method.Finally,simulation results are provided to show that our proposed design outperforms other benchmark schemes in terms of the throughput。展开更多
Adaptive optimization is one of the means that agile organization of command and control resource （AOC2R） adapts for the dynamic battlefield environment. A math model of the adaptive optimization of AOC2R is put for...Adaptive optimization is one of the means that agile organization of command and control resource （AOC2R） adapts for the dynamic battlefield environment. A math model of the adaptive optimization of AOC2R is put forward by analyzing the interrelating concept and research. The model takes the adaptive process as a multi-stage decision making problem. The 2-phases method is presented to calculate the model, which obtains the related parameters by running the colored Petri net （CPN） model of AOC2R and then searches for the result by ant colony optimization （ACO） algorithm integrated with genetic optimization techniques. The simulation results demonstrate that the proposed algorithm greatly improves the performance of AOC2R.展开更多
Crushing roller is one of the main parts of High-p re ssure Grinding Roller, which is a kind of high efficient ore crushing equipment. A kind of assembled roller, which is more convenient to renovate worn surface b y ...Crushing roller is one of the main parts of High-p re ssure Grinding Roller, which is a kind of high efficient ore crushing equipment. A kind of assembled roller, which is more convenient to renovate worn surface b y simply replacing segmented surface of the roller, was developed. The structura l models of assembled roller’s components were designed with SolidWorks softwar e based on feature modeling, these solid models of the roller were virtually ass embled. Through this work, not only was the assemble interference checked out so as to examine validity of the structure design, but also these solid models cou ld be recognized by COSMOS/Works software, through which the finite element an alysis can be done. Then the stress and displacement of the main shaft and sur face segment in two different working states were analyzed and detected quickly according to the analysis results with COSMOS/Works. In conclusion, the optimum clearance of 1.0～2.0 mm between concave-convex studded segments is determined to make the using life of assembled roller longer.展开更多
The 3D inverse design method, which methodology is far superior to the conventional design method that based on geometrical description, is gradually applied in pump blade design. However, no complete description abou...The 3D inverse design method, which methodology is far superior to the conventional design method that based on geometrical description, is gradually applied in pump blade design. However, no complete description about the method is outlined. Also, there are no general rules available to set the two important input parameters, blade loading distribution and stacking condition. In this sense, the basic theory and the mechanism why the design method can suppress the formation of secondary flow are summarized. And also, several typical pump design cases with different specific speeds ranging from centrifugal pump to axial pump are surveyed. The results indicates that, for centrifugal pump and mixed pump or turbine, the ratio of blade loading on the hub to that on the shroud is more than unit in the fore part of the blade, whereas in the aft part, the ratio is decreased to satisfy the same wrap angle for hub and shroud. And the choice of blade loading type depends on the balancing of efficiency and cavitation. If the cavitation is more weighted, the better choice is aft-loaded, otherwise, the fore-loaded or mid-loaded is preferable to improve the efficiency. The stacking condition, which is an auxiliary to suppress the secondary flow, can have great effect on the jet-wake outflow and the operation range for pump. Ultimately, how to link the design method to modem optimization techniques is illustrated. With the know-how design methodology and the know-how systematic optimization approach, the application of optimization design is promising for engineering. This paper summarizes the 3D inverse design method systematically.展开更多
According to the technique requests of the brake caliper in the process of production, a special fixture of float brake caliper has been developed based on 3 D design in this paper. The development process and verifie...According to the technique requests of the brake caliper in the process of production, a special fixture of float brake caliper has been developed based on 3 D design in this paper. The development process and verified data from 3D modeling and kinematics simulation for this special fixture show that this 3D-designed process can conveniently forecast the assembly interference of the fixture and accurately add the mass of lead brick before the prototype is made. In this way the flutter caused by the unbalanced lathe fixture can be eliminated and the precision of run-out tolerance in cylinder hole compared with machine tool spindle can be improved, thus the processing quality of the cylinder hole in a brake caliper can be greatly guaranteed.展开更多
In order to reduce time and cost in engineering design, such as gate design, integral field knowledge must be obtained efficiently. After studying ID3 and its improved methods, a new algorithm(Fuzzy ID3 ) and its main...In order to reduce time and cost in engineering design, such as gate design, integral field knowledge must be obtained efficiently. After studying ID3 and its improved methods, a new algorithm(Fuzzy ID3 ) and its main concepts are presented to overcome some disadvantage in classical ID3 algorithms. In its application of gate design, fuzzy knowledge gotten by the new algorithm is more efficient than the knowledge by other ID3 algorithms, the set of fuzzy knowledge is much smaller than that of knowledge by classical ID3 algorithms. On the other hand, fuzzy knowledge represents field data more naturally to the way of bar thinking and more robust in tolerating imprecise, conflicting and missing information展开更多
Conventional process flow and main work mechanism of alkaline cleaning process of Continual Annealing Line are generally reviewed in the paper,and the work flow of design is analysed including the lye,rinse water circ...Conventional process flow and main work mechanism of alkaline cleaning process of Continual Annealing Line are generally reviewed in the paper,and the work flow of design is analysed including the lye,rinse water circuit,conductivity detection circuit,utility media supply circuit and other main working circuits.Meanwhile,the heat demand of the alkaline cleaning system,rinse water system and dryer device are also analysed.Lumped parameter method in the heat-transfer theory is adopted to calculate the heating time of unsteady heat transfer for strips in the on-line tank.And the reasons why brush roller is of inverse brush and rinsing nozzles are equipped at the inlet side are found.Types and working principles of iron removal and degreasing devices for alkaline cleaning system,which adopt new magnetic filtration and ultra filtration processes,are described.Besides,the bypass filtering method is used to calculate the processing capacity of magnetic filtration and ultra filtration devices.Finally,the related features of 3-Dimension software "PlantSpace" for designing a CAL in Baosteel are totally introduced,such as specification for piping,co-designing,pipe code and 3-Dimension design process.展开更多
This work investigated multiple jet nozzles with various geometrical shape,number of exits,and material on reducing noise radiated from jet flows.Nozzles are categorized in two groups with few and many exit numbers,ea...This work investigated multiple jet nozzles with various geometrical shape,number of exits,and material on reducing noise radiated from jet flows.Nozzles are categorized in two groups with few and many exit numbers,each with various exit shapes,slot and circular,and geometry.Firstly,nozzles are designed and then fabricated by a 3D printer,Form Labs,Form2USA,with polymeric resin.Also,the nozzle with the most noise reduction made of stainless steel.Noise and air thrust were measured at three air pressure gauges,3,5,7 BAR and directions from nozzle apex,30°,90°,135°.Nozzles with slot exit shape made of both plastic and stainless steel revealed the most noise reduction among all nozzles with few exit numbers,nearly 11–14 dB(A)and 11.5–15 dB(A),respectively.On average,slotted nozzle noise reduction was nearly 5–6 dB(A)more than finned nozzle.However,nozzles with more exit numbers,finned and finned-central exit,illustrated much more noise reduction than nozzles with few exit numbers,by almost 16–18 dB(A),they represented similar sound.All tested nozzles and open pipe demonstrated equal air thrust at each pressure gauges.The nozzles with slotted exit shape,either plastic or stainless steel,can provide reasonable noise reduction in comparison to other configuration with few exit numbers.In contrast,nozzles with more exit numbers demonstrated the most noise reduction.展开更多
Energy harvesting technologies provide a promising alternative to battery-powered systems and create an opportunity to achieve sustainable computing for the exploitation of ambient energy sources. However, energy harv...Energy harvesting technologies provide a promising alternative to battery-powered systems and create an opportunity to achieve sustainable computing for the exploitation of ambient energy sources. However, energy harvesting devices and power generators encompass a number of non-classical system behaviors or characteristics, such as delivering nondeterministic power density, and these would create hindrance for effectively utilizing the harvested energy. Previously, we have investigated new design methods and tools that are used to enable power adaptive computing and, particularly, catering non-deterministic voltage, which can efficiently utilize ambient energy sources. Also, we developed a co-optimization approach to maximize the computational efficiency from the harvested ambient energy. This paper will provide a review of these methods. Emerging technologies, such as 3D-IC, which would also enable new paradigm of green and high-performance computing, will be also discussed.展开更多
基金Natural Sciences and Engineering Research Council of Canada,Grant/Award Numbers:Alliance‐Alberta Innovates Program/ALLRP‐561137‐20,Discovery Grant Program/RGPIN‐2020‐05184University of Alberta Future Energy Systems。
文摘Lithium(Li)metal is regarded as one of the most promising anode candidates for next-generation batteries due to its extremely high specific capacity and low redox potential.However,its application is still hindered by the uncontrolled growth of dendritic Li and huge volume fluctuation during cycles.To address these issues,flexible and self-supporting three-dimensional(3D)interlaced Ndoped carbon nanofibers(NCNFs)coated with uniformly distributed 2D ultrathin NiCo_(2)S_(4)nanosheets(denoted CNCS)were designed to eliminate the intrinsic hotspots for Li deposition.Physicochemical dual effects of CNCS arise from limited surface Li diffusivity with a higher Li affinity,leading to uniform Li nucleation and less random accumulation of Li,as confirmed by ab initio molecular dynamics simulations.Due to the unique structure,exchange current density is reduced significantly and metallic Li is further contained within the interspace between the NCNF and NiCo_(2)S_(4)nanosheets,preventing the formation of dendritic Li.The symmetric cell with a Li/CNCS composite anode shows a long-running lifespan for almost 1200 h,with an exceptionally low and stable overpotential under 1mA cm^(-2)/1 mAh cm^(-2).A full cell coupled with a LiFePO4 cathode at a low N/P ratio of 2.45 shows typical voltage profiles but more significantly enhanced performance than that of a LiFePO4 cathode coupled with a bare Li anode.
基金This work was supported by the National Key Research and Development Project under Grant 2020YFB1807602,Natural Science Foundation of China under Grant 62071223,62031012,61701214 and 61661028by the National Key Scientific Instrument and Equipment Development Project under Grant No.61827801+1 种基金the Open Project of the Shaanxi Key Laboratory of Information Communication Network and Security under Grant ICNS201701the Excellent Youth Foundation of Jiangxi Province under Grant 2018ACB21012 and in part by the Young Elite Scientist Sponsorship Program by CAST.
文摘In this paper,we consider a new spectrum sharing scenario for a cognitive relay network,where a secondary unmanned aerial vehicle(UAV)relay receives information from the ground secondary base station(SBS)and transmits information to the ground secondary user(SU),coexisting with the primary users(PUs)at the same wireless frequency band.We investigate the optimization of the UAV relay’s three-dimensional(3D)trajectory to improve the communication throughput performance of the secondary network subject to the interference constraints of the PUs.The information throughput maximization problem is studied by jointly optimizing the UAV relay’s 3D trajectory and the transmit power of the SBS and the UAV,subject to the constraints on the velocity and elevation of the UAV relay,the maximum and average transmit power,and the information causality,as well as a set of interference temperature(IT)constraints.An efficient algorithm is proposed to solve the admittedly challenging non-convex problem by using the path discretization technique,the successive convex approximation technique and the alternating optimization method.Finally,simulation results are provided to show that our proposed design outperforms other benchmark schemes in terms of the throughput。
文摘Adaptive optimization is one of the means that agile organization of command and control resource （AOC2R） adapts for the dynamic battlefield environment. A math model of the adaptive optimization of AOC2R is put forward by analyzing the interrelating concept and research. The model takes the adaptive process as a multi-stage decision making problem. The 2-phases method is presented to calculate the model, which obtains the related parameters by running the colored Petri net （CPN） model of AOC2R and then searches for the result by ant colony optimization （ACO） algorithm integrated with genetic optimization techniques. The simulation results demonstrate that the proposed algorithm greatly improves the performance of AOC2R.
文摘Crushing roller is one of the main parts of High-p re ssure Grinding Roller, which is a kind of high efficient ore crushing equipment. A kind of assembled roller, which is more convenient to renovate worn surface b y simply replacing segmented surface of the roller, was developed. The structura l models of assembled roller’s components were designed with SolidWorks softwar e based on feature modeling, these solid models of the roller were virtually ass embled. Through this work, not only was the assemble interference checked out so as to examine validity of the structure design, but also these solid models cou ld be recognized by COSMOS/Works software, through which the finite element an alysis can be done. Then the stress and displacement of the main shaft and sur face segment in two different working states were analyzed and detected quickly according to the analysis results with COSMOS/Works. In conclusion, the optimum clearance of 1.0～2.0 mm between concave-convex studded segments is determined to make the using life of assembled roller longer.
基金Supported by National Basic Research Program of China(973 Program,Grant No.2009CB724302)
文摘The 3D inverse design method, which methodology is far superior to the conventional design method that based on geometrical description, is gradually applied in pump blade design. However, no complete description about the method is outlined. Also, there are no general rules available to set the two important input parameters, blade loading distribution and stacking condition. In this sense, the basic theory and the mechanism why the design method can suppress the formation of secondary flow are summarized. And also, several typical pump design cases with different specific speeds ranging from centrifugal pump to axial pump are surveyed. The results indicates that, for centrifugal pump and mixed pump or turbine, the ratio of blade loading on the hub to that on the shroud is more than unit in the fore part of the blade, whereas in the aft part, the ratio is decreased to satisfy the same wrap angle for hub and shroud. And the choice of blade loading type depends on the balancing of efficiency and cavitation. If the cavitation is more weighted, the better choice is aft-loaded, otherwise, the fore-loaded or mid-loaded is preferable to improve the efficiency. The stacking condition, which is an auxiliary to suppress the secondary flow, can have great effect on the jet-wake outflow and the operation range for pump. Ultimately, how to link the design method to modem optimization techniques is illustrated. With the know-how design methodology and the know-how systematic optimization approach, the application of optimization design is promising for engineering. This paper summarizes the 3D inverse design method systematically.
文摘According to the technique requests of the brake caliper in the process of production, a special fixture of float brake caliper has been developed based on 3 D design in this paper. The development process and verified data from 3D modeling and kinematics simulation for this special fixture show that this 3D-designed process can conveniently forecast the assembly interference of the fixture and accurately add the mass of lead brick before the prototype is made. In this way the flutter caused by the unbalanced lathe fixture can be eliminated and the precision of run-out tolerance in cylinder hole compared with machine tool spindle can be improved, thus the processing quality of the cylinder hole in a brake caliper can be greatly guaranteed.
文摘In order to reduce time and cost in engineering design, such as gate design, integral field knowledge must be obtained efficiently. After studying ID3 and its improved methods, a new algorithm(Fuzzy ID3 ) and its main concepts are presented to overcome some disadvantage in classical ID3 algorithms. In its application of gate design, fuzzy knowledge gotten by the new algorithm is more efficient than the knowledge by other ID3 algorithms, the set of fuzzy knowledge is much smaller than that of knowledge by classical ID3 algorithms. On the other hand, fuzzy knowledge represents field data more naturally to the way of bar thinking and more robust in tolerating imprecise, conflicting and missing information
文摘Conventional process flow and main work mechanism of alkaline cleaning process of Continual Annealing Line are generally reviewed in the paper,and the work flow of design is analysed including the lye,rinse water circuit,conductivity detection circuit,utility media supply circuit and other main working circuits.Meanwhile,the heat demand of the alkaline cleaning system,rinse water system and dryer device are also analysed.Lumped parameter method in the heat-transfer theory is adopted to calculate the heating time of unsteady heat transfer for strips in the on-line tank.And the reasons why brush roller is of inverse brush and rinsing nozzles are equipped at the inlet side are found.Types and working principles of iron removal and degreasing devices for alkaline cleaning system,which adopt new magnetic filtration and ultra filtration processes,are described.Besides,the bypass filtering method is used to calculate the processing capacity of magnetic filtration and ultra filtration devices.Finally,the related features of 3-Dimension software "PlantSpace" for designing a CAL in Baosteel are totally introduced,such as specification for piping,co-designing,pipe code and 3-Dimension design process.
文摘This work investigated multiple jet nozzles with various geometrical shape,number of exits,and material on reducing noise radiated from jet flows.Nozzles are categorized in two groups with few and many exit numbers,each with various exit shapes,slot and circular,and geometry.Firstly,nozzles are designed and then fabricated by a 3D printer,Form Labs,Form2USA,with polymeric resin.Also,the nozzle with the most noise reduction made of stainless steel.Noise and air thrust were measured at three air pressure gauges,3,5,7 BAR and directions from nozzle apex,30°,90°,135°.Nozzles with slot exit shape made of both plastic and stainless steel revealed the most noise reduction among all nozzles with few exit numbers,nearly 11–14 dB(A)and 11.5–15 dB(A),respectively.On average,slotted nozzle noise reduction was nearly 5–6 dB(A)more than finned nozzle.However,nozzles with more exit numbers,finned and finned-central exit,illustrated much more noise reduction than nozzles with few exit numbers,by almost 16–18 dB(A),they represented similar sound.All tested nozzles and open pipe demonstrated equal air thrust at each pressure gauges.The nozzles with slotted exit shape,either plastic or stainless steel,can provide reasonable noise reduction in comparison to other configuration with few exit numbers.In contrast,nozzles with more exit numbers demonstrated the most noise reduction.
基金supported by the National Natural Science Foundation of China under Grant No. 61176025 and No. 61006027
文摘Energy harvesting technologies provide a promising alternative to battery-powered systems and create an opportunity to achieve sustainable computing for the exploitation of ambient energy sources. However, energy harvesting devices and power generators encompass a number of non-classical system behaviors or characteristics, such as delivering nondeterministic power density, and these would create hindrance for effectively utilizing the harvested energy. Previously, we have investigated new design methods and tools that are used to enable power adaptive computing and, particularly, catering non-deterministic voltage, which can efficiently utilize ambient energy sources. Also, we developed a co-optimization approach to maximize the computational efficiency from the harvested ambient energy. This paper will provide a review of these methods. Emerging technologies, such as 3D-IC, which would also enable new paradigm of green and high-performance computing, will be also discussed.
