The effect of die inlet and transition geometry on the extrusion loads and ~aaterial flow for extrusion of clover sections were investigated and presented both theoretically and experimentally. For this purpose, four ...The effect of die inlet and transition geometry on the extrusion loads and ~aaterial flow for extrusion of clover sections were investigated and presented both theoretically and experimentally. For this purpose, four different die geometries including straight tapered and cosine transition profile and each of them having round and clover inlet geometries were chosen. In the experimental study, commercially pure lead was used because of its hot forming characteristic at room temperature. A newly kinematical admissible velocity field to analyze different profiles of extrusion dies of clover section from round bars was proposed by upper bound analysis. It is clear that the extrusion loads obtained from the theoretical analysis for various die inlet-die transition geometry combinations are in good agreement with the experimental results. Axis deviations of the parts which define the dimensional quality of the products were also investigated.展开更多
As one of the indispensable actuating components in micro-systems,the shafted microgear is in great production demand.Microforming is a manufacturing process to produce microgears to meet the needs.Due to the small ge...As one of the indispensable actuating components in micro-systems,the shafted microgear is in great production demand.Microforming is a manufacturing process to produce microgears to meet the needs.Due to the small geometrical size,there are uncertain process performance and product quality issues in this production process.In this study,the shafted microgears were fabricated in two different scaling factors with four grain sizes using a progressively extrusion-blanking method.To explore the unknown of the process,grain-based modeling was proposed and employed to simulate the entire forming process.The results show that when the grains are large,the anisotropy of single grains has an obvious size effect on the forming behavior and process performance;and the produced geometries and surface quality are worsened;and the deformation load is decreased.Five deformation zones were identified in the microstructures with different hardness and distributions of stress and strain.The simulation by using the proposed model successfully predicted the formation of zones and revealed the inhomogeneous deformation in the forming process.The undesirable geometries of microgears including material unfilling,burr and inclination were observed on the shaft and teeth of gear,and the inclination size is increased obviously with grain size.To avoid the formation of inclination and material unfilling,the punch was redesigned,and a die insert was added to constraint the bottom surface of the gear teeth.The new products had then the better forming quality.展开更多
文摘The effect of die inlet and transition geometry on the extrusion loads and ~aaterial flow for extrusion of clover sections were investigated and presented both theoretically and experimentally. For this purpose, four different die geometries including straight tapered and cosine transition profile and each of them having round and clover inlet geometries were chosen. In the experimental study, commercially pure lead was used because of its hot forming characteristic at room temperature. A newly kinematical admissible velocity field to analyze different profiles of extrusion dies of clover section from round bars was proposed by upper bound analysis. It is clear that the extrusion loads obtained from the theoretical analysis for various die inlet-die transition geometry combinations are in good agreement with the experimental results. Axis deviations of the parts which define the dimensional quality of the products were also investigated.
基金The authors would like to acknowledge the funding support to this research from the projects of ZE1W and BBAT from The Hong Kong Polytechnic University,the National Natural Science Foundation of China(NSFC)(Grant No.51835011)the General Research Fund(GRF)(Grant No.15223520).
文摘As one of the indispensable actuating components in micro-systems,the shafted microgear is in great production demand.Microforming is a manufacturing process to produce microgears to meet the needs.Due to the small geometrical size,there are uncertain process performance and product quality issues in this production process.In this study,the shafted microgears were fabricated in two different scaling factors with four grain sizes using a progressively extrusion-blanking method.To explore the unknown of the process,grain-based modeling was proposed and employed to simulate the entire forming process.The results show that when the grains are large,the anisotropy of single grains has an obvious size effect on the forming behavior and process performance;and the produced geometries and surface quality are worsened;and the deformation load is decreased.Five deformation zones were identified in the microstructures with different hardness and distributions of stress and strain.The simulation by using the proposed model successfully predicted the formation of zones and revealed the inhomogeneous deformation in the forming process.The undesirable geometries of microgears including material unfilling,burr and inclination were observed on the shaft and teeth of gear,and the inclination size is increased obviously with grain size.To avoid the formation of inclination and material unfilling,the punch was redesigned,and a die insert was added to constraint the bottom surface of the gear teeth.The new products had then the better forming quality.
