Influence of dielectric materials on uniformity of large-area capacitively coupled plasmas for N_2/Ar discharges

The effect of the dielectric ring on the plasma radial uniformity is numerically investigated in the practical 450-mm capacitively coupled plasma reactor by a two-dimensional self-consistent fluid model. The simulations were performed for N2/Ar discharges at the pressure of 300 Pa, and the frequency of 13.56 MHz. In the practical plasma treatment process,the wafer is always surrounded by a dielectric ring, which is less studied. In this paper, the plasma characteristics are systematically investigated by changing the properties of the dielectric ring, i.e., the relative permittivity, the thickness and the length. The results indicate that the plasma parameters strongly depend on the properties of the dielectric ring. As the ratio of the thickness to the relative permittivity of the dielectric ring increases, the electric field at the wafer edge becomes weaker due to the stronger surface charging effect. This gives rise to the lower N~+ ion density, flux and N atom density at the wafer edge. Thus the homogeneous plasma density is obtained by selecting optimal dielectric ring relative permittivity and thickness. In addition, we also find that the length of the dielectric ring should be as short as possible to avoid the discontinuity of the dielectric materials, and thus obtain the large area uniform plasma.

Simulation of space charge transport in solid dielectric materials using transmission lines modeling method

In this paper,a lumped RC circuit model,which is based on the Transmission Line Modeling(TLM)method,is used to describe the space charge production and displacement mechanisms in three different solid dielectric materials(LDPE,PTFE and FR4).Each dielectric material is considered as a transmission line with the capacitive and resistance elements.The obtained circuit equations are solved along with the continuity equations for the various charged species in the bulk of solid dielectric material.The electric potential and field,density of different charged species and their recombination rates,resistive and capacitive properties of the solid dielectric material are calculated.In addition,the effects of the variations in the applied voltage,dielectric permittivity and temperature on these physical parameters are examined.Besides,compared with LDPE and PTFE,the net charge density increment rate in FR4 is much higher.Moreover,the influences of temperature on the net charge density in LDPE are not significant.Furthermore,at the higher applied voltages,the current density is increased.Interestingly,the effects of temperature variations on the recombination rates,net charge and current density in LDPE are much lower.Hence,the suitability of LDPE as solid dielectric material is proved.

Modeling and analysis of dielectric materials by using gradient-descent optimization method

This study presents a numerical method based on parallel RC equivalent circuit model fitting methodology for analysis and modeling of dielectric materials.The proposed method employs gradient-descent optimization method(GDOM)to estimate parallel RC equivalent circuit model from current waveforms by minimizing sum of squared difference(SSD)error.Estimation of parallel RC equivalent circuit parameters from measured current waveforms provides a useful tool for identification,simulation and analysis of dielectric materials.Moreover,applications of the proposed method for time and frequency analyses of dielectric materials are demonstrated numerically.Numerical simulations were presented to discuss efficiency of the proposed method for modeling,analysis and monitoring of insulator materials.

Influence of the gassing materials on the dielectric properties of air

Influence of the gassing materials, such as PA6, PMMA, and POM on the dielectric properties of air are investigated. In this work, the fundamental electron collision cross section data were carefully selected and validated. Then the species compositions of the air–organic vapor mixtures were calculated based on the Gibbs free energy minimization. Finally, the Townsend ionization coefficient, the Townsend electron attachment coefficient and the critical reduced electric field strength were derived from the calculated electron energy distribution function by solving the Boltzmann transport equation. The calculation results indicated that H;O with large attachment cross sections has a great impact on the critical reduced electric field strength of the air–organic vapor mixtures. On the other hand, the vaporization of gassing materials can help to increase the dielectric properties of air circuit breakers to some degree.

A Study of the Aging of a-Al_2O_3 Dielectric Material in DBD Plasma

The performance of dielectric material is a key factor against a long time action in dielectric barrier discharge （DBD） plasma. In this study, the aging of the Al2O3 dielectric material was studied by the Atomic Force Microscope （AFM）, X-ray Photoelectron spectrum （XPS） and Auger electron spectrum （AES） methods. The results showerd that the performance of the dielectric does not descend after an 1000 h aging experiment. Therefore the thin dielectric layers of α-Al2O3 porcelain with a purity above 99% can sustain a long time action of DBD plasma and form gas ionization discharges steadily.

MATERIAL MULTIPOLE MECHANICS OF ELASTIC DIELECTRIC COMPOSITES

The overall mechanical and electrical behaviors of elastic dielectric composites are investigated with the aid of the concept of material multipoles. In particular, by introducing a statistical continuum material multipole theory, the effects of the electric-elastic interaction and the microstructure (size, shape, orientation,...) of inhomogeneous particles on the overall behaviors of the composites can be obtained. A basic solution for an ellipsoidal elastic inhomogeneity with electric polarization in an infinite elastic dielectric medium is first given, which shows that classical Eshelby 's elastic solution is modified by the presence of electric-elastic interaction. The overall macroscopic constitutive relations and their overall macroscopic material parameters accounting for electroelastic interaction effect are then derived for the elastic dielectric composites. Some quantitative calculations on the problems with statistical anisotropy, the shape effect and the electric-elastic interaction are finally given for dilute composites.

Preparation and Characterization of Multi Shape ZnO/PVDF Composite Materials

Two different morphologies of ZnO（lotus-shaped, rod-shaped） and ZnO/PVDF composite materials were prepared. The morphologies of ZnO and composite materials were characterized by scanning electron microscopy（SEM） and transmission electron microscopy（TEM）. Fourier transform infrared spectroscopy（FT-IR）, thermal gravimetry（TG）, and X-ray diffraction（XRD） were also used to characterize the chemical structures and phase composites of ZnO and ZnO/PVDF composite materials. Breakdown voltage, dielectric constant and dielectric loss of ZnO/PVDF composite materials were also tested. Microstructure analysis showed that ZnO nanoparticles dispersed uniformly in the matrix. And the dielectric constant expresses a significantly improvement while the dielectric loss and breakdown voltage expresses no significant change. Moreover, dielectric constant keeps an improvement tendency with increasing content of ZnO.

Towards wafer-scale growth of two-dimensional cerium dioxide single crystal with high dielectric performance

Owing to the atomically thin nature,two-dimensional(2D)oxide materials have been widely reported to exhibit exciting transport and dielectric properties,such as fine gate controllability and ultrahigh carrier mobility,that outperform their bulk counterpart.However,unlike the successful synthesis of bulk oxide single crystals,reliable methods for synthesizing large-area single crystal of 2D oxide,that would suppress the negative influence from defective grain boundaries,remain unavailable,especially for nonlayered oxide.Herein,we report that the lattice symmetry between the substrate and cerium dioxide(CeO_(2))would allow for the aligned nucleation and epitaxial growth of CeO_(2)on sapphire substrates,enabling the wafer-sized growth of CeO_(2)single crystal.The careful tuning of the growth temperature and oxygen flow rate contributed to the harvesting of CeO_(2)wafer with reduced thickness and enhanced growth rates.The removal of grain boundaries improved the dielectric performance in terms of high dielectric strength(Ebd≈8.8 MV·cm^(-1)),suppressed leakage current,along with high dielectric constants(εr≈24).Our work demonstrates that with fine dielectric performance and ease of synthesizing wafer-sized single crystals,CeO_(2)can function as potential candidate as gate insulator for 2D-materials based nanoelectronics,and we believe the reported protocol of aligned nucleation can be extended to other 2D oxides.

Effect of dielectric material on the uniformity of nanosecond pulsed dielectric barrier discharge

Dielectric barrier discharge(DBD)is considered as a promising technique to produce large volume uniform plasma at atmospheric pressure,and the dielectric barrier layer between the electrodes plays a key role in the DBD processes and enhancing discharge uniformity.In this work,the uniformity and discharge characteristics of the nanosecond(ns)pulsed DBD with dielectric barrier layers made of alumina,quartz glass,polycarbonate(PC),and polypropylene(PP)are investigated via discharge image observation,voltage-current waveform measurement and optical emission spectral diagnosis.Through analyzing discharge image by gray value standard deviation method,the discharge uniformity is quantitatively calculated.The effects of the space electric field intensity,the electron density(Ne),and the space reactive species on the uniformity are studied with quantifying the gap voltage Ug and the discharge current Ig,analyzing the recorded optical emission spectra,and simulating the temporal distribution of Ne with a one-dimensional fluid model.It is found that as the relative permittivity of the dielectric materials increases,the space electric field intensity is enhanced,which results in a higher Ne and electron temperature(Te).Therefore,an appropriate value of space electric field intensity can promote electron avalanches,resulting in uniform and stable plasma by the merging of electron avalanches.However,an excessive value of space electric field intensity leads to the aggregation of space charges and the distortion of the space electric field,which reduce the discharge uniformity.The surface roughness and the surface charge decay are measured to explain the influences of the surface properties and the second electron emission on the discharge uniformity.The results in this work give a comprehensive understanding of the effect of the dielectric materials on the DBD uniformity,and contribute to the selection of dielectric materials for DBD reactor and the realization of atmospheric pressure uniform,stable,and reactive plasma sources.

Constructing nanocomposites with robust covalent connection between nanoparticles and polymer for high discharged energy density and excellent tensile properties

High discharged energy density and excellent flexible properties in dielectric materials are significantly sought to meet the rapid advancements in the electronics industry. In this study, covalent bonds are constructed between poly(vinylidene fluoride-chlorotrifluoroethylene), which contains olefinic bonds, and thiol-modified BaTiO_(3) at the interface before the nanocomposite films are fabricated. The presence of the covalent bonds is proved to promote the dispersibility of the modified BaTiO_(3) and enhance the interfacial adhesion between the modified BaTiO_(3) and the polymer, followed by a remarkably positive effect in suppressing the dielectric loss(tanδ) and increasing the breakdown strength(Eb) of the nanocomposite films. In addition, the cross-linking treatment in the preparation process is found to be favourable for improving the mechanical properties of the nanocomposite films, which benefits the enhancement of Eb. Furthermore, at 400% elongation, the stretched nanocomposite film doped with 5 vol% modified BaTiO_(3) exhibits an Eb15.6% greater than that of the unstretched film, and the discharged energy density reaches 11.4 J/cm^(3) with a high discharge energy efficiency of 84.5%. This study provides a novel strategy for preparing flexible nanocomposites with powerful interfacial adhesion at high filler content to achieve high discharged energy density.

Fabrication of high-quality colloidal photonic crystals with sharp band edges for ultrafast all-optical switching

Application of the pressure controlled isothermal heating vertical deposition method to the fabrication of colloidal photonic crystals is systematically investigated in this paper. The fabricated samples are characterized by scanning electron microscope and transmission spectrum. High-quality samples with large transmissions in the pass bands and the sharp band edges are obtained and the optimum growth condition is determined. For the best sample, the transmission in the pass bands approaches 0.9 while that in the band gap reaches 0.1. More importantly, the maximum differential transmission as high as 0.1/nm is achieved. In addition, it is found that the number of stacking layers does not increase linearly with concentration of PS spheres in a solution, and a gradual saturation occurs when the concentration of PS spheres exceeds 1.5 wt.%. The uniformity of the fabricated samples is examined by transmission measurements on areas with different sizes. Finally, the tolerance of the fabricated samples to baking was studied.

High Index SMES Device for Gravitomagnetic Field Generation

A method is described for creating a measurable unbalanced gravitational acceleration using a gravitomagnetic field surrounding a superconducting toroid as described by Forward (1962). An experimental Superconducting Magnetic Energy Storage (SMES) toroid configuration of wound superconducting nanowire is proposed to create a measurable acceleration field along the axis of symmetry, providing experimental confirmation of the additive nature of a Lense-Thirring derived gravitomagnetic field. In the present paper, gravitational coupling enhancement of this effect is explored using a high index or high permittivity material, as predicted by Sarfatti (2020) using his modification to Einstein’s General Relativity Field Equations for gravitational coupling in matter.

Recent Advance in Low-Dielectric-Constant Organosilicon Polymers

Comprehensive Summary,Low dielectric(low-k)organosilicon polymers have received extensive interests from industry and academia due to good electrical insulation,high temperature resistance,flame retardancy and hydrophobicity.These attractive properties enable them to be utilized as low-k materials in fabrication of electronic devices in high-frequency communication technology.This review summarizes recent progress in developing low-k organosilicon polymers,including the synthetic methods and properties of different organosilicon polymers classified according to the chemical structures.It may provide some inspiration to design new low-k organosilicon polymers for application in the.

Regulating Zn Deposition via an Artificial Solid–Electrolyte Interface with Aligned Dipoles for Long Life Zn Anode

Aqueous zinc ion batteries show prospects for next-generation renewable energy storage devices.However,the practical applications have been limited by the issues derived from Zn anode.As one of serious problems,Zn dendrite growth caused from the uncontrollable Zn deposition is unfavorable.Herein,with the aim to regulate Zn deposition,an artificial solid–electrolyte interface is subtly engineered with a perovskite type material,BaTiO3,which can be polarized,and its polarization could be switched under the external electric field.Resulting from the aligned dipole in BaTiO3 layer,zinc ions could move in order during cycling process.Regulated Zn migration at the anode/electrolyte interface contributes to the even Zn stripping/plating and confined Zn dendrite growth.As a result,the reversible Zn plating/stripping processes for over 2000 h have been achieved at 1 mA cm^(−2) with capacity of 1 mAh cm−2.Furthermore,this anode endowing the electric dipoles shows enhanced cycling stability for aqueous Zn-MnO2 batteries.The battery can deliver nearly 100%Coulombic efficiency at 2 Ag^(−1) after 300 cycles.

Experimental Study on Triggering Characteristics of a Surface Flashover Triggered Vacuum Switch

Triggering characteristics of triggered vacuum switch （TVS）, including the discharge delay time, delay jitter, range of operational voltage and peak of pulsed current, are investigated. Both structure and experimental circuit of TVS are presented. The results indicate that TVS, as a surface flashover triggering device with high dielectric permittivity material, is with excellent triggering characteristics. When the hold-off voltage reaches 120 kV, the minimum operational voltage is 1.3 kV, and the minimum discharge delay time and jitter are 100 ns and ±10 ns, respectively. The peak current is up to 240 kA when the operational voltage reaches 100 kV. TVS can well satisfy the main demands of high voltage and current applications, and can also be used under a multi-crowbar circuit.

Low Dielectric Benzocyclobutene-type Polymers Based on Facile Synthesis of Linear Fluorinated Monomer

A linear fluorinated benzocyclobutene-type monomer(4F-bis-BCB) was facilely synthesized by a one-step copper-catalyzed etherification reaction and a simple precipitation post-purification method.Moreover,a series of BCB-based polymeric low-dielectric(low-k)materials were obtained by the thermal-induced ring-opening copolymerization of 4F-bis-BCB with divinyl tetramethyl disiloxanebisbenzocyclobutene(DVS-BCB) monomer and further simple thermal curing at high temperature(200-300℃).The resultant fully cured materials demonstrated excellent low dielectric properties at high frequency of 10 GHz(dielectric constant(D_(k))<2.6,dielectric loss(D_(f))<1.57×10^(-2)),great hydrophobicity(water contact angle>116°),ultra-low water absorption(<0.19% after soaked in water at room temperature for 60 h) and excellent planarization ability(surface roughness<0.56 nm of 3 μm-thick film).Overall,this new fluorinated BCB-type monomer provides us an alternative for the facile preparation of low-k polymeric materials and exhibits great potential for future applications in high-frequency communication and three-dimensional high-density packaging technologies.

A Comparison between Abraham and Minkowski Momenta

In this paper I compare the Abraham and the Minkowski forms for the momentum pertaining to an electromagnetic wave inside a dielectric or a magnetic material. The discussion is based on a careful treatment of the surface charges and currents and of the forces acting on them. While in the dielectric case the Abraham momentum is certainly more appealing from the physical point of view, for a magnetic material it suggests an interpretation in terms of magnetic charges and related magnetic currents. The Minkowski momentum for magnetic non conducting materials, on the contrary, has a natural interpretation in terms of an amperian model, in which the dynamics is determined by the Lorentz force acting on bulk and surface electric currents.

Design strategies of high-performance lead-free electroceramics for energy storage applications

A greater number of compact and reliable electrostatic capacitors are in demand due to the Internet of Things boom and rapidly growing complex and integrated electronic systems,continuously promoting the development of high-energy-density ceramic-based capacitors.Although significant successes have been achieved in obtaining high energy densities in lead-based ferroelectric ceramics,the utilization of lead-containing ceramies has been restricted due to environmental and health hazards of lead.Lead-free ferroelectric ceramics have garnered tremendous attention and are expected to replace lead-based ceramics in the near future.However,the energy density of lead-free ceramics is still lagging behind that of lead-containing cou.nterparts,severely limiting their applications.Significant efforts have been made to enhance the energy storage performance of lead-free ceramics using multi-scale design strategies,and exciting progress has been achieved in the past decade.This review briefly discusses the energy storage mechanism and fundamental characteristics of a dielectric capacitor,summarizes and compares the state-of-the-art design strategies for high-energy-density lead-free ceramics,and highlights several critical issues and requirements for industrial production.The prospects and challenges of lead-free ceramics for energy storage applications are also discussed.

Influence of a high-speed dielectric spherical particle's movement on its scattering characteristics

The scattered field and differential scattered section （DSS） of a moving spherical particle with a high speed are investigated numerically. The coordinate and vector transformations are used to establish a theoretical basis for studying the laser scattering of a moving particle. The DSS of a moving spherical particle is explained by the electric and magnetic field from Mie scattering theory. Assuming the laser wavelength of 1.06μ m, we compute the ratio of the laser DSS of the moving dielectric spherical particle to that of the static dielectric spherical particle, which changes with radii, speeds and scattering angles of the particle. The numerical results show that the laser DSS of the moving spherical particle is tightly connected with its speed and scattering zenith angle. If a spherical particle moves with high speed, the laser DSS due to movement of the particle could not be neglected. If the speed of the dielectric spherical particle is fluctuating, the Doppler effect and the frequency spectrum expansion play important roles.

Impact of organic contamination in vacuum on laser-induced damage threshold of TiO_2/SiO_2 dielectric mirrors

The influence of organic contamination in vacuum on the laser-induced damage threshold （LIDT） of coatings is studied. TiO2/SiO2 dielectric mirrors with high reflection at 1064 nm are deposited by the electronbeam evaporation method and their LIDTs are measured in vacuum and atmosphere, respectively. It is found that the contamination in vacuum is easily attracted to optical surfaces because of the low pressure and becomes the source of damage, O2 molecules in vacuum with contamination can accelerate the laser-induced damage by observing LIDT and damage morphologies. LIDTs of mirrors have a little change in vacuum compared with in atmosphere when the organic contamination is wiped off. The results indicate that organic contamination is a significant reason to decrease the LIDT in vacuum.