Force and impulse multi-sensor based on flexible gate dielectric field effect transistor

Nowadays,force sensors play an important role in industrial production,electronic information,medical health,and many other fields.Two-dimensional material-based filed effect transistor(2D-FET)sensors are competitive with nano-level size,lower power consumption,and accurate response.However,few of them has the capability of impulse detection which is a path function,expressing the cumulative effect of the force on the particle over a period of time.Herein we fabricated the flexible polymethyl methacrylate(PMMA)gate dielectric MoS_(2)-FET for force and impulse sensor application.We systematically investigated the responses of the sensor to constant force and varying forces,and achieved the conversion factors of the drain current signals(I_(ds))to the detected impulse(I).The applied force was detected and recorded by I_(ds)with a low power consumption of~30 nW.The sensitivity of the device can reach~8000%and the 4×1 sensor array is able to detect and locate the normal force applied on it.Moreover,there was almost no performance loss for the device as left in the air for two months.

Alternative Strategy for Development of Dielectric Calcium Copper Titanate‑Based Electrolytes for Low‑Temperature Solid Oxide Fuel Cells

The development of low-temperature solid oxide fuel cells(LT-SOFCs)is of significant importance for realizing the widespread application of SOFCs.This has stimulated a substantial materials research effort in developing high oxide-ion conductivity in the electrolyte layer of SOFCs.In this context,for the first time,a dielectric material,CaCu_(3)Ti_(4)O_(12)(CCTO)is designed for LT-SOFCs electrolyte application in this study.Both individual CCTO and its heterostructure materials with a p-type Ni_(0.8)Co_(0.15)Al_(0.05)LiO_(2−δ)(NCAL)semiconductor are evaluated as alternative electrolytes in LT-SOFC at 450–550℃.The single cell with the individual CCTO electrolyte exhibits a power output of approximately 263 mW cm^(-2) and an open-circuit voltage(OCV)of 0.95 V at 550℃,while the cell with the CCTO–NCAL heterostructure electrolyte capably delivers an improved power output of approximately 605 mW cm^(-2) along with a higher OCV over 1.0 V,which indicates the introduction of high hole-conducting NCAL into the CCTO could enhance the cell performance rather than inducing any potential short-circuiting risk.It is found that these promising outcomes are due to the interplay of the dielectric material,its structure,and overall properties that led to improve electrochemical mechanism in CCTO–NCAL.Furthermore,density functional theory calculations provide the detailed information about the electronic and structural properties of the CCTO and NCAL and their heterostructure CCTO–NCAL.Our study thus provides a new approach for developing new advanced electrolytes for LT-SOFCs.

Ultrahigh performance passive radiative cooling by hybrid polar dielectric metasurface thermal emitters

Real-world passive radiative cooling requires highly emissive,selective,and omnidirectional thermal emitters to maintain the radiative cooler at a certain temperature below the ambient temperature while maximizing the net cooling power.Despite various selective thermal emitters have been demonstrated,it is still challenging to achieve these conditions sim-ultaneously because of the extreme difficulty in controlling thermal emission of photonic structures in multidimension.Here we demonstrated hybrid polar dielectric metasurface thermal emitters with machine learning inverse design,en-abling a high emissivity of~0.92 within the atmospheric transparency window 8-13μm,a large spectral selectivity of~1.8 and a wide emission angle up to 80 degrees,simultaneously.This selective and omnidirectional thermal emitter has led to a new record of temperature reduction as large as~15.4°C under strong solar irradiation of~800 W/m2,signific-antly surpassing the state-of-the-art results.The designed structures also show great potential in tackling the urban heat island effect,with modelling results suggesting a large energy saving and deployment area reduction.This research will make significant impact on passive radiative cooling,thermal energy photonics and tackling global climate change.

Enhancing the Performance of Perovskite Light-Emitting Diodes via Synergistic Effect of Defect Passivation and Dielectric Screening

Metal halide perovskites,particularly the quasi-two-dimensional perovskite subclass,have exhibited considerable potential for next-generation electroluminescent materials for lighting and display.Nevertheless,the presence of defects within these perovskites has a substantial influence on the emission efficiency and durability of the devices.In this study,we revealed a synergistic passivation mechanism on perovskite films by using a dual-functional compound of potassium bromide.The dual functional potassium bromide on the one hand can passivate the defects of halide vacancies with bromine anions and,on the other hand,can screen the charged defects at the grain boundaries with potassium cations.This approach effectively reduces the probability of carriers quenching resulting from charged defects capture and consequently enhances the radiative recombination efficiency of perovskite thin films,leading to a significant enhancement of photoluminescence quantum yield to near-unity values(95%).Meanwhile,the potassium bromide treatment promoted the growth of homogeneous and smooth film,facilitating the charge carrier injection in the devices.Consequently,the perovskite light-emitting diodes based on this strategy achieve a maximum external quantum efficiency of~21%and maximum luminance of~60,000 cd m^(-2).This work provides a deeper insight into the passivation mechanism of ionic compound additives in perovskite with the solution method.

Effect of dielectric material on the uniformity of nanosecond pulsed dielectric barrier discharge

Dielectric barrier discharge(DBD)is considered as a promising technique to produce large volume uniform plasma at atmospheric pressure,and the dielectric barrier layer between the electrodes plays a key role in the DBD processes and enhancing discharge uniformity.In this work,the uniformity and discharge characteristics of the nanosecond(ns)pulsed DBD with dielectric barrier layers made of alumina,quartz glass,polycarbonate(PC),and polypropylene(PP)are investigated via discharge image observation,voltage-current waveform measurement and optical emission spectral diagnosis.Through analyzing discharge image by gray value standard deviation method,the discharge uniformity is quantitatively calculated.The effects of the space electric field intensity,the electron density(Ne),and the space reactive species on the uniformity are studied with quantifying the gap voltage Ug and the discharge current Ig,analyzing the recorded optical emission spectra,and simulating the temporal distribution of Ne with a one-dimensional fluid model.It is found that as the relative permittivity of the dielectric materials increases,the space electric field intensity is enhanced,which results in a higher Ne and electron temperature(Te).Therefore,an appropriate value of space electric field intensity can promote electron avalanches,resulting in uniform and stable plasma by the merging of electron avalanches.However,an excessive value of space electric field intensity leads to the aggregation of space charges and the distortion of the space electric field,which reduce the discharge uniformity.The surface roughness and the surface charge decay are measured to explain the influences of the surface properties and the second electron emission on the discharge uniformity.The results in this work give a comprehensive understanding of the effect of the dielectric materials on the DBD uniformity,and contribute to the selection of dielectric materials for DBD reactor and the realization of atmospheric pressure uniform,stable,and reactive plasma sources.

Achieving Synergistic Improvement in Dielectric and Energy Storage Properties of All-Organic Poly(Methyl Methacrylate)-Based Copolymers Via Establishing Charge Traps

How to achieve synergistic improvement of permittivity(ε_(r))and breakdown strength(E_(b))is a huge challenge for polymer dielectrics.Here,for the first time,theπ-conjugated comonomer(MHT)can simultaneously promote theε_(r)and E_(b)of linear poly(methyl methacrylate)(PMMA)copolymers.The PMMA-based random copolymer films(P(MMA-co-MHT)),block copolymer films(PMMA-b-PMHT),and PMMA-based blend films were prepared to investigate the effects of sequential structure,phase separation structure,and modification method on dielectric and energy storage properties of PMMA-based dielectric films.As a result,the random copolymer P(MMA-coMHT)can achieve a maximumε_(r)of 5.8 at 1 kHz owing to the enhanced orientation polarization and electron polarization.Because electron injection and charge transfer are limited by the strong electrostatic attraction ofπ-conjugated benzophenanthrene group analyzed by the density functional theory(DFT),the discharge energy density value of P(MMA-co-PMHT)containing 1 mol%MHT units with the efficiency of 80%reaches15.00 J cm^(-3)at 872 MV m^(-1),which is 165%higher than that of pure PMMA.This study provides a simple and effective way to fabricate the high performance of polymer dielectrics via copolymerization with the monomer of P-type semi-conductive polymer.

Ultrahigh-resolution,high-fidelity quantum dot pixels patterned by dielectric electrophoretic deposition

The high pixel resolution is emerging as one of the key parameters for the next-generation displays.Despite the development of various quantum dot(QD)patterning techniques,achieving ultrahigh-resolution(>10,000 pixels per inch(PPI))and high-fidelity QD patterns is still a tough challenge that needs to be addressed urgently.Here,we propose a novel and effective approach of orthogonal electric field-induced template-assisted dielectric electrophoretic deposition to successfully achieve one of the highest pixel resolutions of 23090(PPI)with a high fidelity of up to 99%.Meanwhile,the proposed strategy is compatible with the preparation of QD pixels based on perovskite CsPbBr3 and conventional CdSe QDs,exhibiting a wide applicability for QD pixel fabrication.Notably,we further demonstrate the great value of our approach to achieve efficiently electroluminescent QD pixels with a peak external quantum efficiency of 16.5%.Consequently,this work provides a general approach for realizing ultrahighresolution and high-fidelity patterns based on various QDs and a novel method for fabricating QD-patterned devices with high performance.

High discrimination ratio,broadband circularly polarized light photodetector using dielectric achiral nanostructures

The on-chip measurement of polarization states plays an increasingly crucial role in modern sensing and imaging applications.While high-performance monolithic linearly polarized photodetectors have been extensively studied,integrated circularly polarized light(CPL)photodetectors are still hindered by inadequate discrimination capability.This study presents a broadband CPL photodetector utilizing achiral all-dielectric nanostructures,achieving an impressive discrimination ratio of~107 at a wavelength of 405 nm.Our device shows outstanding CPL discrimination capability across the visible band without requiring intensity calibration.It functions based on the CPL-dependent near-field modes within achiral structures:under left or right CPL illumination,distinct near-field modes are excited,resulting in asymmetric irradiation of the two electrodes and generating a photovoltage with directions determined by the chirality of the incident light field.The proposed design strategy facilitates ultra-compact CPL detection across diverse materials,structures,and spectral ranges,presenting a novel avenue for achieving high-performance monolithic CPL detection.

Dielectric metamaterials with effective self-duality and full-polarization omnidirectional brewster effect

Conventional dielectric solid materials,both natural and artifcial,lack electromagnetic self-duality and thus require additional coatings to achieve impedance matching with free space.Here,we present a class of dielectric metamaterials that are effectively self-dual and vacuum-like,thereby exhibiting full-polarization omnidirectional impedance matching as an unusual Brewster effect extended across all incident angles and polarizations.With both birefringence and reflection eliminated regardless of wavefront and polarization,such anisotropic metamaterials could establish the electromagnetic equivalence with"stretched free space"in transformation optics,as substantiated through full-wave simulations and microwave experiments.Our findings open a practical pathway for realizing unprecedented polarization-independence and omnidirectional impedance-matching characteristics in pure dielectric solids.

The effects of inner electrode shape on the performance of dielectric barrier discharge reactor for oxidative removal of NO and SO_(2)

Seagoing vessels are responsible for more than 90%of global freight traffic,but meanwhile,emission pollutants(NO_(x)and SO_(x))of seagoing vessels also cause serious air pollution.Nonthermal plasma(NTP)combined with wet scrubbing technology is considered to be a promising technology.In order to improve the oxidation efficiency and energy efficiency of the NTP reactor,the screw and rod inner electrodes of dielectric barrier discharge(DBD)reactor were investigated.To analyze the mechanism,the optical emission spectra(OES)of NTP were measured and numerical calculation was applied.The experiment results show that the NO oxidation removal efficiency of screw electrode is lower than that of rod electrode.However,the SO_(2)removal efficiency of screw electrode is higher.According to the OES experiment and numerical calculation,the electric field intensity of the screw electrode surface is much higher than that of the rod electrode surface,and it is easier to generate N radicals to form NO.For the same energy density condition,the OH radical generation efficiency of the screw electrode reactor is similar to that of the rod electrode,but the gas temperature in the discharge gap is higher.Therefore,the SO2 oxidation efficiency of the thread electrode is higher.This study provides guidance for the optimization of oxidation efficiency and energy consumption of DBD reactor.

Racemic dielectric metasurfaces for arbitrary terahertz polarization rotation and wavefront manipulation

Dielectric chiral metasurface is a new type of planar and efficient chiral optical device that shows strong circular dichroism or optical activity,which has important application potential in optical sensing and display.However,the two types of chiral optical responses in conventional chiral metasurfaces are often interdependent,as their modulation of the amplitudes and phases of orthogonal circularly polarized components is correlated,which limits the further progress of chiral meta-devices.Here we propose a new scheme for independently designing the circular dichroism and optical activity of chiral metasurfaces to further control the polarization and wavefront of transmitted waves.Inspired by mixtures of chiral molecular isomers,we use the dielectric isomer resonators to form“super-units”instead of single meta-atoms for chiral responses in terahertz band,which is called racemic metasurface.By introducing two levels of Pancharatnam-Berry phases between meta-atoms and“super-units”,the polarization rotation angle and wavefront of the beam can be designed without the far-field circular dichroism.We demonstrate the strong control ability on terahertz waves of this scheme through simulation and experiments.In addition,this new type of device with near-field chirality but no far-field circular dichroism may also have important value in optical sensing and other technologies.

Solvation Effects on the Dielectric Constant of 1 M LiPF6 in Ethylene Carbonate:Ethyl Methyl Carbonate 3:7

We report the dielectric constant of 1 M LiPF_(6)in EC:EMC 3∶7 w/w(ethylene carbonate/ethyl methyl carbonate)in addition to neat EC:EMC 3∶7 w/w.Using three Debye relaxations,the static permittivity value,or dielectric constant,is extrapolated to 18.5,which is compared to 18.7 for the neat solvent mixture.The EC solvent is found to strongly coordinate with the Li^(+)cations of the salt,which results in a loss of dielectric contribution to the electrolyte.However,the small amplitude and large uncertainty in relaxation frequency for EMC cloud definitive identification of the Li^(+)solvation shell.Importantly,the loss of the free EC permittivity contribution due to Li^(+)solvation is almost completely balanced by the positive contribution of the associated LiPF_(6)salt,demonstrating that a significant quantity of dipolar ion pairs exists in 1 M LiPF_(6)in EC:EMC 3∶7.

Silicon-based dielectric elastomer with amino-complexed hybrids towards high actuation performance

For improving the actuation performance at low electric fields of dielectric elastomers,achieving high dielectric constant(εr)and low modulus(Y)simultaneously has been targeted in the past decades,but there are few ways to accomplish both.In contrast to the classical strategies such as incorporating plasticizers or ceramic to prepare the silicon-based dielectric elastomers,here,blending an amino-complexed hybrid(polyethyleneimine(PEI)-Ag)with polydimethylsiloxane(PDMS)elastomer is reported as an alternative strategy to tailor theεr and Y.PEI-Ag not only exhibits excellent dielectric enhancement properties but also minimizes the PDMS crosslinking through amino-complexed reaction between PEI and Pt catalysts.The prepared dielectric elastomers have aεr of 7.2@10^(3)Hz and Y of 1.14 MPa,leading to an actuation strain of 22.27%at 35 V/μm.Hence,incorporating such novel hybrids based on dual amino-complexed effect on both matrix and particles sufficiently promotes the actuated performance of dielectric elastomers.

Dielectric anisotropy in liquid crystal mixtures with nematic and smectic phases

The modulation of dielectric anisotropy(△ε)is pivotal for elucidating molecular interactions and directing the alignment of liquid crystals.In this study,we combine liquid crystals with opposing dielectric anisotropies to explore the impact of varying concentrations on their properties.We report the sign-reversal of△εin both the nematic and smectic A phases of these mixed liquid crystals,alongside a dual-frequency behaviour across a broad temperature spectrum.Our research further quantifies the influence of mixture ratios under various temperatures and electric field frequencies.This exploration may pave the way for the discovery of new physical phenomena.

Boron nitride silicone rubber composite foam with low dielectric and high thermal conductivity

Silicone rubber(SR)is widely used in the field of electronic packaging because of its low dielectric properties.In this work,the porosity of the SR was improved,and the dielectric constant of the SR foam was reduced by adding expanded microspheres(EM).Then,the thermal conductivity of the system was improved by combining the modified boron nitride(f-BN).The results showed that after the f-BN was added,the dielectric constant and dielectric loss were much lower than those of pure SR.Micron-sized modified boron nitride(f-mBN)improved the dielectric and thermal conductivity of the SR foam better than that of nano-sized modified boron nitride(f-nBN),but f-nBN improved the volume resistivity,tensile strength,and thermal stability of the SR better than f-mBN.When the mass ratio of f-mBN and fnBN is 2:1,the thermal conductivity of the SR foam reaches the maximum value of 0.808 W·m^(-1)·K^(-1),which is 6.5 times that before the addition.The heat release rate and fire growth index are the lowest,and the improvement in flame retardancy is mainly attributed to the high thermal stability and physical barrier of f-BN.

Influences of divalent ion substitution on the magnetic and dielectric properties of W-type barium ferrite

Saturation magnetization,magneto-crystalline anisotropy field,and dielectric properties are closely related to microwave devices applied at different frequencies.For regulating the magnetic and dielectric properties of W-type barium ferrites,single-phase BaMe_(2)Fe_(16)O_(27)(Me=Fe,Mn,Zn,Ni,Co) with different Me ions were synthesized by the high-temperature solid-state method.The saturation magnetization(Ms) range from 47.77 emu/g to 95.34 emu/g and the magnetic anisotropy field(H_a) range from 10700.60 Oe(1 Oe=79.5775 A·m^(-1)) to 13739.57 Oe,depending on the type of cation substitution in the hexagonal lattice.The dielectric permittivity and dielectric loss decrease with increasing frequency of the AC electric field in the low-frequency region,while they almost remain constant in the high-frequency region.The charac teristics of easy regulation and preparation make it a potential candidate for use in microwave device applications.

Surface charge characteristics in a three-electrode surface dielectric barrier discharge

The surface charge characteristics in a three-electrode surface dielectric barrier discharge(SDBD)are experimentally investigated based on the Pockels effect of an electro-optical crystal. The actuator is based on the most commonly used SDBD structure for airflow control, with an exposed electrode supplied with sinusoidal AC high voltage, a grounded encapsulated electrode and an additional exposed electrode downstream supplied with DC voltage. The ionic wind velocity and thrust can be significantly improved by increasing DC voltage although the plasma discharge characteristics are virtually unaffected. It is found that the negative charges generated by the discharge of the three-electrode structure accumulate on the dielectric surface significantly further downstream in an AC period compared to the actuator with a two-electrode structure. The negative charges in the downstream region increase as the DC voltage increases.In addition, the DC voltage affects the time required for the positive charge filaments to decay.The positive DC voltage expands the ionic acceleration zone downstream to produce a greater EHD force. The amplitude of the DC voltage affects the electric field on the dielectric surface and is therefore a key factor in the formation of the EHD force. Further research on the surface charge characteristics of a three-electrode structure has been conducted using a pulse power to drive the discharge, and the same conclusions are drawn. This work demonstrates a link between surface charge characteristics and EHD performance of a three-electrode SDBD actuator.

Fatigue Resistance of RCA Modified Asphalt Based on Dielectric Properties

In order to study the anti-fatigue performance of RCA modified asphalt (RMA),the performance of RMA and 90#matrix asphalt with different modifier content were measured by asphalt penetration,ductility,softening point,Brookfield viscosity,rheological index,infrared spectrum and dielectric constant test.This paper discusses the changes of asphalt basic indexes,fatigue properties and asphalt components based on dielectric properties under different modifier contents,and analyzes the grey correlation degree between components and asphalt pavement performance indexes.The results show that the optimum content of RCA modifier is 16.7%of the asphalt quality according to the penetration,ductility,softening point,Brockfield viscosity,viscosity temperature curve and fatigue life.In the phase angle-strain curve,there is disorder in the latter part of the curve.According to the strain (ε_(d)) corresponding to the disorder point,a new fatigue failure criterion is proposed and proved.Based on the new asphalt fatigue failure criterion,the fatigue prediction model of asphalt mixture is improved,and the fatigue life predicted by the improved fatigue model is compared with the fatigue life obtained by four-point bending fatigue test.The results show that the proposed new asphalt fatigue failure criterion is reasonable,and the fatigue life predicted by the improved asphalt mixture fatigue prediction model is accurate.The research method of classifying asphalt components based on dielectric properties is simple and effective,and the components have a high correlation with the road performance of base asphalt and modified asphalt.

Reconfigurable(4, 6^(2)) and(4, 8^(2)) Archimedean plasma photonic crystals in dielectric barrier discharge

Archimedean photonic crystal has become a research area of great interest due to its various unique properties. Here, we experimentally demonstrate the realization of reconfigurable(4, 6^(2))and(4, 8^(2)) Archimedean plasma photonic crystals(APPCs) by use of dielectric barrier discharges in air. Dynamical control on both the macrostructures including the lattice symmetry and the crystal orientation, and the microstructures including the fine structures of scattering elements has been achieved. The formation mechanisms of APPCs are studied by time-resolved measurements together with numerical simulations. Large omnidirectional band gaps of APPCs have been obtained. The tunable topology of APPCs may offer new opportunities for fabricating multi-functional and highly-integrated microwave devices.

Experimental study on the effect of H_(2)O and O_(2) on the degradation of SF_(6) by pulsed dielectric barrier discharge

SF_(6) has excellent insulation performance and arc extinguishing ability,and is widely used in the power industry.However,its global warming potential is about 23,500 times that of C0_(2),it can exist stably in the atmosphere,it is not easily degradable and is of great potential harm to the environment.Based on pulsed dielectric barrier discharge plasma technology,the effects of H_(2)O and 0_(2) on the degradation of SF_(6) were studied.Studies have shown that H_(2)O can effectively promote the decomposition of SF_(6) and improve its degradation rate and energy efficiency of degradation.Under the action of a pulse input voltage and input frequency of 15 kV and 15 kHz,respectively,when H_(2)O is added alone the effect of 1% H_(2)O is the best,and the rate and energy efficiency of degradation of SF_(6) reach their maximum values,which are 91.9% and 8.25 g kWh^(-1),respectively.The synergistic effect of H_(2)O and O_(2) on the degradation of SF_(6) was similar to that of H_(2)O.When the concentration of H_(2)O and O_(2) was 1%,the system obtained the best rate and energy efficiency of degradation,namely 89.7% and 8.05 g kWh~(-1),respectively.At the same time,different external gases exhibit different capabilities to regulate decomposition products.The addition of H_(2)O can effectively improve the selectivity of S0_(2).Under the synergistic effect of H_(2)O and O_(2),with increase in O_(2) concentration the degradation products gradually transformed into SO_(2)F_(2).From the perspective of harmless treatment of the degradation products of SF_(6),the addition of O_(2) during the SF_(6) degradation process should be avoided.