The micro-emulsification diesel oil with water dopant of 5%, 10% and 15% was prepared using the NAA micro-emulsification compound developed by the authors. The engine bench testing was carried out on the 485QB diesel ...The micro-emulsification diesel oil with water dopant of 5%, 10% and 15% was prepared using the NAA micro-emulsification compound developed by the authors. The engine bench testing was carried out on the 485QB diesel engine. From the testing results of velocity, loading and exhaust gas, it can be seen that the power decreases and the fuel consumption increases using the micro-emulsification diesel oil. But based on the actual fuel consumption, the use of emulsification diesel with water dopant of 10% can get the effect of oil saving; while with water donant of more than 15% , it doesnt work evidently. The investigation shows that using the micro - emulsification diesel oil, we can reduce the exhaust gas pollution and receive better environment benefit.展开更多
The soot surface growth plays significant role on the soot mass accumulation,which starts with H(hydrogen)atom abstraction forming activated soot surface sites,and is followed by the acetylene addition process.In this...The soot surface growth plays significant role on the soot mass accumulation,which starts with H(hydrogen)atom abstraction forming activated soot surface sites,and is followed by the acetylene addition process.In this study,the effect of the mixture inhomogeneity and combustion temperature on the soot surface activity and soot formation was investigated by developing a new multi-step phenomenological(MSP)soot model of diesel engines.A new detailed soot surface growth mechanism was proposed by correlation analysis of combustion parameters with soot formation.The inhomogeneity coefficient of soot surface activityαCH and the specific rate of soot surface growth R CH were derived to highlight the effect of inhomogeneity of mixture and combustion temperature on soot formation.The predicted diesel engine-out soot agreed well with experimental findings in wide ranges of combustion conditions.In the case of lower engine load with single fuel injection and higher EGR(exhaust gas recirculation)rate,it had quiet homogeneous mixtures before ignition when the combustion temperature dominated the soot surface activity.At medium engine load with multi-pulse fuel injections,it got mixture slightly stratified before ignition and revealed that the mixture inhomogeneity became more dominated on soot surface activity than the combustion temperature.An increased soot surface activity led to increased soot emission.Under the full engine loads with single fuel injection but quite high boost pressure over 0.4 MPa,it led to the combustion conditions of higher mixture density and higher mixture heat capacity,which benefits the mixture homogeneity.The decay rate of soot surface activity became lower due to the decreased combustion temperature and the soot surface activity decreased due to improved mixture homogeneity.In addition,the lowered intake oxygen concentration due to usage of EGR played a role to lower the specific rate of soot surface growth R CH,but to increase the soot surface activityαCH.展开更多
We studied engine-out soot samples collected from a heavy-duty direct-injection diesel engine and port-fuel injection gasoline spark-ignition engine. The two types of soot samples were characterized using Raman spectr...We studied engine-out soot samples collected from a heavy-duty direct-injection diesel engine and port-fuel injection gasoline spark-ignition engine. The two types of soot samples were characterized using Raman spectroscopy with different laser powers. A Matlab program using least-square-method with trust-region-reflective algorithm was developed for curve fitting. A DOE(design of experiments) method was used to avoid local convergence. The method was used for two-band fitting and three-band fitting. The fitting results were used to determine the intensity ratio of D(for "Defect" or "Disorder") and G(for"Graphite") Raman bands. It is found that high laser power may cause oxidation of soot sample, which gives higher D/G intensity ratio. Diesel soot has consistently higher amorphous/graphitic carbon ratio, and thus higher oxidation reactivity, compared to gasoline soot, which is reflected by the higher D/G intensity ratio in Raman spectra measured under the same laser power.展开更多
文摘The micro-emulsification diesel oil with water dopant of 5%, 10% and 15% was prepared using the NAA micro-emulsification compound developed by the authors. The engine bench testing was carried out on the 485QB diesel engine. From the testing results of velocity, loading and exhaust gas, it can be seen that the power decreases and the fuel consumption increases using the micro-emulsification diesel oil. But based on the actual fuel consumption, the use of emulsification diesel with water dopant of 10% can get the effect of oil saving; while with water donant of more than 15% , it doesnt work evidently. The investigation shows that using the micro - emulsification diesel oil, we can reduce the exhaust gas pollution and receive better environment benefit.
基金supported by the National Natural Science Foundation of China through its key project funding CNFS(Grant No.51236005)the Ministry of Science and Technology through its 973 National Key Project(Grant No.2013CB228401)
文摘The soot surface growth plays significant role on the soot mass accumulation,which starts with H(hydrogen)atom abstraction forming activated soot surface sites,and is followed by the acetylene addition process.In this study,the effect of the mixture inhomogeneity and combustion temperature on the soot surface activity and soot formation was investigated by developing a new multi-step phenomenological(MSP)soot model of diesel engines.A new detailed soot surface growth mechanism was proposed by correlation analysis of combustion parameters with soot formation.The inhomogeneity coefficient of soot surface activityαCH and the specific rate of soot surface growth R CH were derived to highlight the effect of inhomogeneity of mixture and combustion temperature on soot formation.The predicted diesel engine-out soot agreed well with experimental findings in wide ranges of combustion conditions.In the case of lower engine load with single fuel injection and higher EGR(exhaust gas recirculation)rate,it had quiet homogeneous mixtures before ignition when the combustion temperature dominated the soot surface activity.At medium engine load with multi-pulse fuel injections,it got mixture slightly stratified before ignition and revealed that the mixture inhomogeneity became more dominated on soot surface activity than the combustion temperature.An increased soot surface activity led to increased soot emission.Under the full engine loads with single fuel injection but quite high boost pressure over 0.4 MPa,it led to the combustion conditions of higher mixture density and higher mixture heat capacity,which benefits the mixture homogeneity.The decay rate of soot surface activity became lower due to the decreased combustion temperature and the soot surface activity decreased due to improved mixture homogeneity.In addition,the lowered intake oxygen concentration due to usage of EGR played a role to lower the specific rate of soot surface growth R CH,but to increase the soot surface activityαCH.
文摘We studied engine-out soot samples collected from a heavy-duty direct-injection diesel engine and port-fuel injection gasoline spark-ignition engine. The two types of soot samples were characterized using Raman spectroscopy with different laser powers. A Matlab program using least-square-method with trust-region-reflective algorithm was developed for curve fitting. A DOE(design of experiments) method was used to avoid local convergence. The method was used for two-band fitting and three-band fitting. The fitting results were used to determine the intensity ratio of D(for "Defect" or "Disorder") and G(for"Graphite") Raman bands. It is found that high laser power may cause oxidation of soot sample, which gives higher D/G intensity ratio. Diesel soot has consistently higher amorphous/graphitic carbon ratio, and thus higher oxidation reactivity, compared to gasoline soot, which is reflected by the higher D/G intensity ratio in Raman spectra measured under the same laser power.
