A Strategy to Control the Turbocharger Energy of a Diesel Engine at Different Altitudes

Power deterioration is a major problem for diesel engines operating at high altitudes.This problem stems from the limited availability of turbocharger energy,which is not enough to increase the boost pressure to the required level.In this study,a control strategy is introduced in order to achieve engine power recovery at different altitudes.It is shown that as the altitude increases from 0 to 4500 m,the required boost pressure ratio increases from 2.4 to 4.3.The needed turbocharger energy should be increased accordingly by 240%,and the TCC(turbine characterization coefficient)should be adjusted within wide ranges.A 12%decrease in the TCC can lead to a rise of the intake air pressure,which can compensate the pressure decrease due to a 1000 m altitude increase.The fluctuation range of boost pressure was within 14.5 kPa for variations in altitude from 0 to 4500 m.

Analysis of the Emissions and Performance of a Diesel Engine Using Pumpkin Seed Oil Methyl Ester with Different Injection Pressures

Biodiesel fuel is a potential alternative energy source for diesel engines due to its physiochemical characteristics relatively similar to those of traditional diesel fuel.In this study,the performance,emission,and combustion features of a mono cylinder DI diesel engine are assessed using 20%Pumpkin seed methyl ester(PSOME20)and considering varying injection pressures(200,220,240,and 260 bar).The considered Pumpkin seed oil is converted into pumpkin biodiesel by transesterification and then used as fuel.The findings demonstrate that the Brake Thermal Efficiency(BTE)of PSOME20 can be raised by 1.68%,and the carbon monoxide(CO),hydrocarbon(HC),and smoke emanations can be lowered,while oxides of nitrogen(NOx)emissions are increased at an injection pressure(IP)of 240 bar compared to the standard IP of 200 bar.The cylinder pressure and the Heat Release Rate(HRR)become higher at 240 bar,whereas the ignition delay is shortened with respect to PSOME20 at a normal IP of 200 bar.

Optimizing the Exhaust System of Marine Diesel Engines to Improve Low-speed Performances and Cylinder Working Conditions

Proper design of exhaust systems in marine high-power turbocharged diesel engines can contribute to improve the low-speed performance of these engines and make the working conditions of the cylinders more uniform.Here a high-power marine 16-cylinder V-type turbocharged diesel engine is simulated using the GT-Power software.The results reveal the differences induced by different exhaust system structures,such as an 8-cylinder-inpipe exhaust system with single/double superchargers and a 4-cylinder-in-pipe exhaust system with a single supercharger.After a comparative analysis,the 8-cylinder type with double superchargers is determined to be the optimal solution,and the structure of the exhaust system is further optimized.The simulations show that the optimized maximum exhaust temperature difference among cylinders is reduced by 66%.Finally,the simulation results and the optimized performance of the designed exhaust system are verified through experiments.

Experimental Study on Performance and Combustion Analysis of a Diesel Engine Fueled with Diesel and Jatropha Oil Blended with Heptane

This work focuses on blending Jatropha oil with diesel fuel and heptane to improve its physico-chemical characteristics for production of blends and their use as fuel in a diesel engine. The influence of the heptane content was evaluated by comparing the results obtained from the engine (performance and combustion parameters) with those of the diesel fuel and straight Jatropha oil. The results obtained show an improvement in engine performance especially at low loads. Specifically, a reduction in the specific fuel consumption of the engine is obtained when the heptane content in the mixture is around 10% compared to that obtained with pure Jatropha oil. The best results were obtained with the blend containing 70% Jatropha oil, 20% diesel fuel and 10% heptane (J70G20H10). Overall engine efficiency and exhaust gas temperatures are comparable for all fuels tested. Engine combustion parameters are improved with J70G20H10. The results obtained with J70G20H10 are close to those of the engine operating on diesel fuel. The cyclic dispersion is low with coefficients of variation of the indicated mean effective pressure (COVIMEP) whose values are less than 10%. The lowest values of the COVIMEP are obtained with the blend J70G20H10.

Experimental Study on the Performance and Emission of Chinese Small Agricultural Diesel Engine Fuelled with Methanol/Biodiesel/DTBP

Diesel engine alternative fuels, such as methanol and biodiesel, are beneficial to reduce diesel engine emission. In order to study the influence of methanol and biodiesel on the performance, economy and emission of small agricultural diesel engine, the physical-chemical properties(cetane number, lower heat value(LHV), viscosity, etc.) of methanol and biodiesel were analyzed. The methanol and biodiesel showed good complementary property to some extent. When a large proportion of methanol was added into biodiesel, the cetane number of the methanol/biodiesel blend will be greatly reduced. Since the cetane number of the blend fuel has great influence on the combustion process of diesel engine, after testing for blending ratio of methanol/biodiesel, the blend was prepared with 5%(BM5), 10%(BM10) and 15%(BM15) methanol, respectively. Di-Tert-Butyl Peroxide(DTBP) was chosen as a cetane number improver to be added into methanol/biodiesel blend. 0.25%, 0.50% and 0.75% of DTBP was added into BM15. The bench test was carried out on a 186 FA diesel engine to study the effect of methanol and DTBP on the engine performance and emissions. The results show that, at rated condition, compared with biodiesel, the NO;concentration of BM5, BM10 and BM15 is reduced by 5.02%, 33.85% and 21.24%, and smoke is reduced by 5.56%, 22.22% and 55.56%. However, the engine power is also reduced by 5.77%, 14.23% and 25.41%, and the brake specific energy consumption is increased by 3.31%, 7.78% and 6.37%. The addition of DTBP in methanol/biodiesel could recover the engine power to the level of diesel. DTBP shows good effect on the reduction of the brake specific energy consumption and NO_(x), CO, HC concentration, but a little increase of exhaust smoke.

Performance of Tractor Diesel Engine with Animal-Fats Biodiesel

Animal fats biodiesel were manufactured and tested for its performance in the tractor engine and fuel adoptability in the field works. Four different fuels, three different content of biodiesel （BD20, BD50 and BD100） and light oil, were prepared and tested in the four strokes diesel engine. Power output, fuel consumption rate and exhaust gases of the four fuels in the diesel engine were compared and discussed. Power output of light oil engine was the greatest showing 5.3% difference between light oil and BDI00. But, almost no power difference between light oil engine and BD20 engine, light oil engine produced 0.37% more power than BD20 engine superior to better power than BD20 engine. Less exhaust gases of CO2, CO, NOx and total hydrocarbon （THC） were produced from animal fats biodiesel than light oil, which confirmed that biodiesel is environmental friendly fuel. For fuel adoptability in the tractor, biodiesel engine tractor showed its fuel competitiveness comparing with light oil for tractor works in the paddy field.

Performance Characteristics of Single Cylinder Diesel Engine under Different Operating Conditions

Recently, it is predicted that the fossil fuels will be sufficient for a few decades at the present extraction rates. So, the performance studies of the internal combustion engines play an important role to achieve the best operating point at different weather temperatures. In the present study, the effects of the inlet air temperatures on the engine performance characteristics were studied at different cooling loads. Several experiments were carried out on a single cylinder diesel engine （SCDI）. The performance characteristics of SCDI included： brake power, specific fuel consumption, brake thermal efficiency and exhaust emissions （carbon dioxide, CO2, carbon monoxide CO, and hydrocarbon HC）. The findings show that the inlet air temperature and cooling conditions have appreciable effect on the performance characteristics of the SCDI especially at low cooling rate. It can be concluded that the high cooling rate leads to the enhancement in the brake thermal efficiency, the b.s.f.c, and the emitted COz, CO, and HC. On the other hand the high cooling rate leads to the decrease in the volumetric efficiency. So, a compromising between the inlet air temperature and the cooling rate should be recommended for the engine best performance.

Simulation of a DI Diesel Engine Performance Fuelled on Biodiesel Using a Semi-Empirical 0D Model

Diesel engines have proven over the years important in terms of efficiency and fuel consumption to power generation ratio. Many research works show the potential of biodiesel as a substitute for conventional gasoil. Mainly, previous and recent researches have focused on experimental investigation of diesel engine performance fuelled by biodiesel. Researches on the mathematical description of diesel engine process running on biodiesel are scarce, and mostly about chemical and thermodynamic description of the combustion process of biodiesel rather than performance studies. This work describes a numerical investigation on the performance analysis of a diesel engine fuelled by palm oil biodiesel. The numerical investigation was made using a semi empirical 0D model based on Wiebe’s and Watson’s model which was implemented via the open access numerical calculation software Scilab. The model was validated first by comparing with experimental pressure and performance data of a one cylinder engine at rated speed and secondly by comparing with a six cylinders engine performance data at various crankshaft rotational speeds. Simulations were then made to analyze the engine performance when running on biodiesel. The calculations were made at constant combustion duration and constant coefficient of excess air. Results showed that the model matches the overall experimental data, such as the power output and peak cylinder pressure. The ignition delay was somehow underestimated by the model for the first experiment, which caused a slight gap on in cylinder pressure curve, whereas it predicted the average ignition delay fairly well for the second set of validation. The simulations of engine performance when running on biodiesel confirmed results obtained in previous experimental researches on biodiesel. The model will be further investigated for engine control when shifting to biodiesel fuel.

Comparative Study of Performances of a Single-Cylinder Diesel Enginefueled with Pure Diesel and Blends of Biodiesels/Pure Diesel

In this study, the principal objective is to compare the performances of an air-cooled one cylinder, four-stroke direct injection diesel engine using the blends (5% by volume B5, 10% by volume B10) of diesel and biodiesels derived respectively from palm oil, castor oil and raphia sese De Wild oil with pure diesel. All the biodiesels used in this work come from the plant species of the democratic republic of Congo as listed above. The engine performances (power, torque and brake specific consumption) at different engine speeds were determined at both full and partial loads. According to experimental results, the increments in the power output and torque when the mixtures of diesel and biodiesels were used and were observed. On the other side, the specific fuel consumption of the mixtures is higher than that of pure diesel although the calculated lower heating values are almost within the same range for the all studied fuels. Finally, in partial load 1/1, pure diesel blended with biodiesels B5 derived from castor oil presented high specific brake consumption values compared to the other fuels while B10 from the same oil presents low brake specific consumption values for power greater than 3.2 kW.

Effect of <i>γ</i>-Valerolactone Blending on Engine Performance, Combustion Characteristics and Exhaust Emissions in a Diesel Engine

γ-valerolactone (GVL) is a C5-cyclic ester that can be produced from biomass providing a potentially renewable fuel for transportation and feedstock for the chemical industry. Experiments were performed with fossil diesel (D), D + biodiesel (BD) and D + BD + GVL blends. A four-cylinder, turbocharged direct injection diesel engine was used for the tests. The engine was coupled to a dynamometer to vary the load. CO, NOx, THC and smoke emissions were measured by using a multi-channel gas analyzer. Combustion characteristics were assessed by in-cylinder pressure data with respect to crank angle and the derived heat release rates. Compared with D, and D + BD blends, addition of GVL had relatively little effect on engine performance and NOx emission, but reduced the exhaust concentration of CO, unburned fuel and smoke significantly. The smoke reduction is particularly notable in view of the very recent suggestion that black carbon is the second most important greenhouse gas in the atmosphere next to carbon dioxide. No diesel engine study with GVL has been reported so far.

Effect of Palm Oil Biodiesel Blends on Engine Emission and Performance Characteristics in an Internal Combustion Engine

Increasing global environmental issues and depleting fossil fuel reserves has necessitated the need for alternative and sustainable fuel. In this paper, the effects of biodiesel and its blend on engine emission and performance characteristics in an internal combustion engine were analyzed. Biodiesel derived from the transesterification of raw palm oil was blended with diesel fuel at different proportions designated as PO5 (5% Biodiesel and 95% Diesel), PO10 (10% Biodiesel and 90% Diesel), PO15 (15% Biodiesel and 85% Diesel), PO20 (20% Biodiesel and 80% Diesel), PO50 (50% Biodiesel and 50% Diesel), PO85 (85% Biodiesel and 15% Diesel), and PO100 (100% Biodiesel). A Lombardini 2-cylinder, four-stroke direct injection diesel engine with a compression ratio of 22.8 was developed using Ricardo Wave software in which diesel, palm oil biodiesel blends and pure biodiesel are used in the model, and the obtained results were analysed and presented. The simulation was done under varying engine speeds of 1200 rpm to 3200 rpm at full load condition. Biodiesel and its blends are more environment-friendly and non-toxic when compared to diesel fuel;it also improves the mechanical efficiency of the engines, and above all can also lead to a reduction in poverty among rural dwellers. The obtained results showed that brake specific fuel consumption and brake thermal efficiency increased with palm oil biodiesel blends as compared to diesel fuel which might be a result of biodiesel’s lower heating value, and the increase in thermal energy may be a result of the oxygenation of the biodiesel blend as compared to pure diesel. In terms of brake torque, palm oil biodiesel blends were lesser than diesel fuel. The CO, HC, and NOx emissions of palm oil biodiesel blends decreased significantly compared to that of pure diesel. From this study, palm oil biodiesel emits lesser emissions than diesel fuel and its performance characteristics are similar to diesel fuel. Therefore, palm oil biodiesel can be used without any modifications directly in a diesel engine. In addition, it can also be used as blends as an alternative and sustainable fuel, decreasing air pollution, and increasing environmental sustainability.

Emission and performance study emulsi ed orange peel oil biodiesel in an aspirated research engine

This study paves the way on reducing smoke emission and NO_x emissions of research diesel engine by detailing the e ect of water addition in biodiesel. Fuel samples were prepared with di erent concentrations of water in orange peel oil biodiesel(94% waste orange peel oil biodiesel + 4% water + 2% Span 80(WOPOBDE1) and 90% waste orange peel oil biodiesel + 8% water + 2% Span 80(WOPOBDE2). Span 80 was employed as a nonionic surfactant, which emulsifies water in biodiesel. Experimental results revealed that the nitrogen oxides and smoke emission of orange peel oil biodiesel emulsion were reduced by 11%–19% and 3%–21%, respectively, compared to that of neat orange peel oil biodiesel(WOPOBD). In addition, the introduction of orange peel oil–water emulsions in the diesel engine considerably reduced the emissions of unburned hydrocarbons and carbon monoxide. The overall hydrocarbon emission of WOPOBDE2 was 12.2% lower than that of WOPOBD and 16.3% lower than that of diesel. The overall CO emission of WOPOBDE2 was 17% lower than that of base fuel(WOPOBD) and 21.8% lower than that of diesel. Experimental results revealed that modified fuel had higher brake thermal e ciency and lower brake specific fuel consumption than that of base fuel at all engine brake power levels.

Study on Performance and Emission Characteristics of a Compression Ignition Engine Fueled with Diesel-2 Ethoxy Ethyl Acetate Blends

Diesel engines are the major contributors of various types of air polluting gases like carbon monoxide, oxides of nitrogen, smoke, etc. Improvement of fuel properties is essential for suppression of Diesel pollutant emissions along with the optimization of design factors and after treatment equipment. Studies conducted in the past have shown that a significant reduction were obtained in the emissions using oxygenates. This paper investigates the performance and emission characteristics of a direct injection Diesel engine fueled with 2 Ethoxy Ethyl Acetate (EEA) blends. Different fuel blends which contain 5%, 10% and 15% of EEA were prepared and the effect of these blends on performance and emissions were studied on a single cylinder direct injection Diesel engine. The blends were tested under different load conditions and the result showed that EEA blended fuels improves the performance of the engine and reduce the emission level significantly.

Compacted graphite iron-A material solution for modern diesel engine cylinder blocks and heads

The demands for improved fuel economy,performance and emissions continue to pose challenges for engine designers and the materials they choose. This is particularly true for modern diesel engines,where the primary path to achieving improved engine performance and emissions is to increase the Peak Firing Pressure in the combustion chamber. The resulting increase in thermal and mechanical loading has required a change from conventional grey cast iron to Compacted Graphite Iron (CGI) in order to satisfy durability requirements without increasing the size or the weight of the engines. With at least 75% higher tensile strength,45% higher stiffness and approximately double the fatigue strength of conventional grey cast iron,CGI satisfies durability requirements and also provides the dimensional stability required to meet emissions legislation throughout the life of the engine. Currently,there are no CGI diesel engines running on the roads in North America. This is set to change considerably as new commercial vehicle and pick-up SUV diesel engines are launched with CGI cylinder blocks in 2008 and 2009. These initial programs will provide over 2 million CGI diesel engines when ramped to mature volume,potentially accounting for 10%-15% of the North American passenger vehicle fleet within the next four years.

Design and Research of the EQ6105DTAA Diesel Engine

The EQ6105DTAA diesel engine which first pattern en gi ne is EQD6105T is developed through the original EQ6102 diesel engine and other advanced engine structures. This paper analyses performance parameters, general layout and parts design process of the diesel engine. The development cycle is s horten by CAD/CAE/CAM technology. Through experiment, the general performance of the engine is in keeping ahead in our country. With boosting mid-cooling technology and related designing correction in EQ6105 DTAA diesel engine, it had obtained better motivity and economy. The full load s teady smog emission and smog emission during simulated free accelerating are all meeting with GB14761.6-93, GB3847-1999 limit requirement. The prototype had p assed reliability test and has reliable parts. It performance indexes are in the leading position in same diesel engine in China. The 13 working conditions gas pollute and particle discharging in this pro totype can meet the limit requirement of GB17691-2001, phase I. The EQ6105DTAA diesel engine parts has good generality with existing types, which lower down th e production cost.

Controlling of NO_x Emitted from a Diesel Engine Fueled on Biodiesel: Theoretical Modeling and Experimental Evaluation

The development of a diesel engine model using one-dimensional （1-D） fluid-dynamic engine simulation codes,and its validation using experimental measurements are described in this paper.The model was calibrated by running the engine on an electric dynamometer at eight steady-state operating conditions.The refined engine model was used to predict the oxides of nitrogen （NOx） less than those measured earlier in the experiments,and hence to recommend changes in the engine for the verification of the results.The refined engine model is greatly influenced by the start of injection angle （ψ）,ignition delay （φ）,premix duration （DP）,and main duration （DM） for the prediction of reduced NOx emissions.It is found that optimum ψ is 6.5° before top dead center （BTDC）.At this angle,the predicted and experimental results are in good agreement,showing only a difference of up to 4%,6.2%,and 7.5% for engine performance,maximum combustion pressure （Pmax）,and NOx,respectively.

Influence of Exhaust Gas Recirculation on Low-Load Diesel Engine Performance

In the condition of constant speed and light load, an experimental study of a turbocharged and intercooled diesel engine with exhaust gas recirculation （EGR） system focuses on the influence of different EGR rates on combustion process, dynamic performance, economic performance and emission performance of a diesel engine. With the increase of EGR rate, the oxygen concentration of the intake-side decreases, the fuel air equivalence ratio increases, and the maximum explosion pressure in the cylinder decreases. Meanwhile, the average temperature in the cylinder drops, the ignition delay is prolonged, the ignition timing delays, and the maximum heat release rate decreases. The increase of EGR rate makes NOx emissions decrease obviously and continue to decline. When EGR is low, the smoke rate enlarges slowly with the increase of EGR rate, and enlarges greatly at the rate higher than 43% and reaches the maximum at the rate of 57%. When EGR rate is higher than 61%, the smoke rate drops rapidly, and the content of CO and hydrocarbon （HC） increases rapidly with high EGR rate.

Performance, emission and combustion characteristics of DI diesel engine running on blends of honne oil/diesel fuel/kerosene/DMC

Honne oil(tamanu)(H),a non-edible vegetable oil is native for northwards of Northern Marianas islands and the Ryukyu Islands in southern Japan and westward throughout Polynesia.It has remained as an untapped new possible source of alternative fuel that can be used as diesel engine fuel.Literature pertaining to use of vegetable oil in diesel engine with kerosene and dimethyl carbonate(DMC)is scarce.The present research is aimed to investigate experimentally the performance,exhaust emission and combustion characteristics of a direct injection(DI)diesel engine,typically used in agricultural sector,over the entire load range,when fuelled with neat diesel(ND)and blends of diesel fuel(D)/DMC/H/kerosene(K).DMC/D/H/K blends have a potential to improve the performance and emissions and to be an alternative to ND.Experiments have been conducted when fuelled with H20(20%H+80%D),HK(20%H+40%K+40%D)and HKD5(20%H+40%K+35D+5%DMC)to HKD15 in steps of 5%DMC keeping H and K percentages constant.The emissions(CO,HC and smoke density(SD))of fuel blend HKD15 are found to be lowest,with SD dropping significantly.The NOx level is slightly higher with HKD5 to HKD15 as compared to ND.The brake thermal efficiency of HKD5 to HKD15 is same and it is higher than that of ND.There is a good trade off between NOx and SD.Peak cylinder pressure and premixed combustion phase increases as DMC content increase.

Performance, emission and combustion characteristics of direct injection diesel engine running on calophyllum inophyllum linn oil (honne oil)

The present work examines the use of a non-edible vegetable oil namely honne oil,a new possible source of alternative fuel for diesel engine.A Direct Injection(DI)diesel engine typically used in agricultural sector was operated on Neat Diesel(ND)and neat honne oil(H100).At maximum load,with H100,brake thermal efficiency and NOx emission decreased where as emissions like CO,HC,smoke opacity increased.With H100,peak cylinder pressure and maximum rate of pressure rise decreased compared to ND.With H100,occurrence of peak pressure is away from top dead center compared to ND.With H100,ignition delay and combustion duration increased compared to ND.

Experimental Study on Thermal Balance of Regulated Two-Stage Turbocharged Diesel Engine at Variable Altitudes

It is significant to study thermal balance of diesel engine under different variable geometry turbocharger(VGT)vane openings at variable altitudes,which is helpful to assess the heat distribution,control the heat load and improve the heat efficiency of the diesel engine.A thermal balance test system was built to study the influence of the VGT vane opening angles on a regulated two-stage turbocharged(RTST)diesel engine’s thermal balance performance.The experiment was conducted under full load operating conditions at different altitudes(0 m,3500 m and 5500 m).Results indicated that the heat load of engine increased and the thermal efficiency decreased with the increase of altitudes under all operating conditions.As the VGT vane openings increased,the exhaust and maximum combustion temperature increased,while the maximum cylinder combustion pressure decreased.In particular,the maximum combustion temperature was more than 2000 K when the VGT vane openings were greater than 70%at the altitude of 5500 m,and the maximum combustion pressure exceeded 17 MPa when the opening of VGT vane was 70%at 0 m.The thermal efficiency of the engine decreased with the increase of VGT vane openings at the altitudes of 0 m and 5500 m,but the thermal efficiency increased and then decreased at the altitude of 3500 m.It was finally obtained that the best openings of VGT vane was 80%,60%and 50%under the engine speed of 2100 r/min at 0 m,3500 m and 5500 m,respectively.