The performance of the electronic unit pump (EUP) diesel engine is studied, it will be used in the integrated powertrain and its multi parameters are controllable. Both the theoretical analysis and experiment research...The performance of the electronic unit pump (EUP) diesel engine is studied, it will be used in the integrated powertrain and its multi parameters are controllable. Both the theoretical analysis and experiment research are taken. A control unit for the fuel quantity and timing in crankshaft domain is designed on this basis and the engine experiment test has been done. For the constant speed camshaft driving EUP system, the fuel quantity will increase as the supply angle goes up and injection timing has no effect. The control precision can reach 1°CA. The full injection timing MAP and engine peak performance curves are made successfully.展开更多
The high working junction temperature of power component is the most common reason of its failure. So the thermal design is of vital importance in electronic control unit （ECU） design. By means of circuit simulation...The high working junction temperature of power component is the most common reason of its failure. So the thermal design is of vital importance in electronic control unit （ECU） design. By means of circuit simulation, the thermal design of ECU for electronic unit pump （EUP） fuel system is applied. The power dissipation model of each power component in the ECU is created and simulated. According to the analyses of simulation results, the factors which affect the power dissipation of components are analyzed. Then the ways for reducing the power dissipation of power components are carried out. The power dissipation of power components at different engine state is calculated and analyzed. The maximal power dissipation of each power component in all possible engine state is also carried out based on these simulations. A cooling system is designed based on these studies. The tests show that the maximum total power dissipation of ECU drops from 43.2 W to 33.84 W after these simulations and optimizations. These applications of simulations in thermal design of ECU can greatly increase the quality of the design, save the design cost and shorten design time展开更多
The type PT-821 PT Pump test stand and type PT-881 injector test stand are a set of special test stands for calibration of PT Pumps and injectors of Cummins engines. Both test stands may be used in conjunction with an...The type PT-821 PT Pump test stand and type PT-881 injector test stand are a set of special test stands for calibration of PT Pumps and injectors of Cummins engines. Both test stands may be used in conjunction with any model of Bosch injection pump test benches for PT Pumps and injector calibration. During PT Pump calibration, the type PT-821 test stand should be used in conjunction with a Bosch injection pump lest bench. The PT Pump to be tested is installed on the Bosch injection pump test bench through a mounting bracket and is driven by the bench shaft. When calibrating PT injectors, both the PT-881 injector test stand and the PT-821 PT Pump test stand should be used in conjunction with a Bosch injection pump test bench, with the PT-881 injector test stand installed on Bosch test bench. The injector to be tested is driven by the Bosch injection pump test bench through a coupling. This paper describes the structure and function of the PT-821 PT Pump test stand and PT-881 injector test stand. Some technical problems arc described in detail.展开更多
Application of CuO-water nanofluid with size of the nanoparticles of 20 nm and volume concentrations up 2% is numerically investigated in a radiator of Chevrolet Suburban diesel engine under turbulent flow conditions....Application of CuO-water nanofluid with size of the nanoparticles of 20 nm and volume concentrations up 2% is numerically investigated in a radiator of Chevrolet Suburban diesel engine under turbulent flow conditions. The heat transfer relations between airflow and nanofluid coolant have been obtained to evaluate local convective and overall heat transfer coefficients and also pumping power for nanofluid flowing in the radiator with a given heat exchange capacity. In the present study, the effects of the automotive speed and Reynolds number of the nanofluid in the different volume concentrations on the radiator performance are also investigated. The results show that for CuO-water nanofluid at 2% volume concentration circulating through the flat tubes with Renf = 6000 while the automotive speed is 70 km/hr, the overall heat transfer coefficient and pumping power are approximately 10% and 23.8% more than that of base fluid for given conditions, respectively.展开更多
文摘The performance of the electronic unit pump (EUP) diesel engine is studied, it will be used in the integrated powertrain and its multi parameters are controllable. Both the theoretical analysis and experiment research are taken. A control unit for the fuel quantity and timing in crankshaft domain is designed on this basis and the engine experiment test has been done. For the constant speed camshaft driving EUP system, the fuel quantity will increase as the supply angle goes up and injection timing has no effect. The control precision can reach 1°CA. The full injection timing MAP and engine peak performance curves are made successfully.
文摘The high working junction temperature of power component is the most common reason of its failure. So the thermal design is of vital importance in electronic control unit （ECU） design. By means of circuit simulation, the thermal design of ECU for electronic unit pump （EUP） fuel system is applied. The power dissipation model of each power component in the ECU is created and simulated. According to the analyses of simulation results, the factors which affect the power dissipation of components are analyzed. Then the ways for reducing the power dissipation of power components are carried out. The power dissipation of power components at different engine state is calculated and analyzed. The maximal power dissipation of each power component in all possible engine state is also carried out based on these simulations. A cooling system is designed based on these studies. The tests show that the maximum total power dissipation of ECU drops from 43.2 W to 33.84 W after these simulations and optimizations. These applications of simulations in thermal design of ECU can greatly increase the quality of the design, save the design cost and shorten design time
文摘The type PT-821 PT Pump test stand and type PT-881 injector test stand are a set of special test stands for calibration of PT Pumps and injectors of Cummins engines. Both test stands may be used in conjunction with any model of Bosch injection pump test benches for PT Pumps and injector calibration. During PT Pump calibration, the type PT-821 test stand should be used in conjunction with a Bosch injection pump lest bench. The PT Pump to be tested is installed on the Bosch injection pump test bench through a mounting bracket and is driven by the bench shaft. When calibrating PT injectors, both the PT-881 injector test stand and the PT-821 PT Pump test stand should be used in conjunction with a Bosch injection pump test bench, with the PT-881 injector test stand installed on Bosch test bench. The injector to be tested is driven by the Bosch injection pump test bench through a coupling. This paper describes the structure and function of the PT-821 PT Pump test stand and PT-881 injector test stand. Some technical problems arc described in detail.
文摘Application of CuO-water nanofluid with size of the nanoparticles of 20 nm and volume concentrations up 2% is numerically investigated in a radiator of Chevrolet Suburban diesel engine under turbulent flow conditions. The heat transfer relations between airflow and nanofluid coolant have been obtained to evaluate local convective and overall heat transfer coefficients and also pumping power for nanofluid flowing in the radiator with a given heat exchange capacity. In the present study, the effects of the automotive speed and Reynolds number of the nanofluid in the different volume concentrations on the radiator performance are also investigated. The results show that for CuO-water nanofluid at 2% volume concentration circulating through the flat tubes with Renf = 6000 while the automotive speed is 70 km/hr, the overall heat transfer coefficient and pumping power are approximately 10% and 23.8% more than that of base fluid for given conditions, respectively.
