Design and preparation of frequency doubling antireflection coating with different thicknesses of interlayer for LiB3O5 crystal

Design and preparation of frequency doubling antireflection coating with different thicknesses of interlayer were investigated for LIB3O5 （LBO） substrate. The design was based on the vector method. The thickness of the inserted SiO2 interlayer could be changed in a wide range for the four-layer design with two zeros at 1064 and 532 nm. The coatings without any interlayer and with 0.1 quarter-wave （λ/4）, 0.3 λ/4, 0.5 λ/4 SiO2 interlayer were deposited respectively on LBO by using electron beam evaporation technique. All the prepared coatings with SiO2 interlayer indicated satisfying optical behavior. This expanded our option for the thickness of an interlayer when coating on LBO substrate. The prepared films with SiO2 interlayer showed better adhesion than that without any interlayer. The thickness of the interlayer affected the adhesion, the adhesion for the coating with 0.5 λ/4 SiO2 interlayer was not as good as the other two.

Characterization of Interface Charge in NbAlO/AlGaN/GaN MOSHEMT with Different NbAlO Thicknesses

We investigate the influence of interface charge on electrical performance of NbAIO/A1GaN/GaN metal-oxide- semiconductor high electron mobility transistors （MOSHEMTs）. Through C-V measurements and simulations, we find that the donor-type interface fixed charge density Qit of 2.2 × 10^13 cm^-2 exists at the NbA10/A1GaN interface, which induces the shift of the threshold voltage much more negative. Furthermore, a trap density of approximately 0.43 × 10^13-1.14 ×10^13 cm^-2 eV^-1 is obtained at the NaA10/AlGaN interface, which is consistent with the frequency-dependent capacitance and conductance measurement results.

Study on Folds of Equal Thickness Multi-layerSandwiched in Different Thickness Media

The theoretical model and non-homogeneous differential equation of equal thickness multi-layer folds sandwiched in different thickness and same character media are established by elastic and plastic mechanics. The special answer of the non-homogeneous differential equation and the common answer of the homogeneous differential equation are deduced by applying logistic equation and special function, and the dominant wavelength theory of equal thickness multi-layer folds sandwiched in different thickness and same character media. In addition, the experimental folding in both elastic and sticky materials proves the dominant wavelength theory.

Research and application on the automatic measuring device for testing transverse thickness difference of cold-rolling steel sheet

Many advanced technologies have been applied in developing the automatic measuring device for testing transverse thickness difference of cold-rolling steel sheet,such as the technologies of automatic control,sensor measurement,marking identification,photographic location,computer application and information transmission.This measuring device can measure the transverse thickness difference of the steel plate accurately and quickly,with a high detection level of automation.It is an effective detection equipment for transverse thickness control of steel plate.Horizontal width of steel plate measuring 0.8-1.4 m, horizontal measurement point positioning accuracy±0.02 mm,thickness range 0.2-2.0 mm, measurement accuracy within±1μm.

Development history and technological progress of non-oriented electrical steel sheets at Baosteel

This paper briefly summarized the development history, product catalogue and magnetic properties of non- oriented electrical steel sheets at Baosteel, as well as the development and application of high-value-added steel grades. Recent advances in manufacturing electrical steel sheets were also introduced, including technologies for controlling inclusion,for producing high-grade steel strips by a tandem rolling mill and for controlling the transverse thickness difference of steel sheets, and the development of environmentally friendly coatings.

Transverse thickness difference control technology for non-oriented silicon steel

Transverse thickness difference is an important quality index of non-oriented silicon steel strips. In order to fulfill users＇ accuracy requirements on the transverse thickness of silicon steel and improve the production yield, the factors influencing transverse thickness difference were analyzed. Then the work roll shape, control strategy and incoming hot-rolled strips were optimized. Since the optimization measures were implemented in the actual production, the thickness difference of non-oriented silicon steel has been reduced greatly and fulfilled the requirements placed by users. These measures have achieved remarkable effects.

Whole process prediction model of silicon steel strip on transverse thickness difference based on Takagi-Sugeno fuzzy network

The hot rolling and cold rolling control models of silicon steel strip were examined.Shape control of silicon steel strip of hot rolling was a theoretical analysis model,and the shape control of cold rolling was a data-based prediction model.The mathematical model of the hot-rolled silicon steel section,including the crown genetic model,inter-stand crown recovery model,and hot-rolled strip section prediction model,is used to control the shape of hot-rolled strip.The cold rolling shape control is mainly based on Takagi-Sugeno fuzzy network,which is used to simulate and predict the transverse thickness difference of cold-rolled silicon steel strip.Finally,a predictive model for the transverse thickness difference of silicon steel strips is developed to provide a new quality control method of transverse thickness of combined hot and cold rolling to improve the strip profile quality and increase economic efficiency.The qualified rate of the non-oriented silicon steel strip is finally obtained by applying this model,and it has been steadily upgraded to meet the needs of product quality and flexible production.

THICKNESS-DEPENDENCE OF RESIDUAL STRESS IN LEAD-FREE FERROELECTRIC K_(0.5)Na_(0.5)NbO_(3) FILMS

Lead-free ferroelectric K_(0.5)Na_(0.5)NbO_(3)(KNN)films with different thicknesses were prepared by polyvinlypyrrolidone(PVP)-modified chemical solution deposition(CSD)method.Their residual stresses were studied with two methods of X-ray diffraction(XRD)and nanoindentation fracture.It was found that the tensile stress occurs in KNN films with small thickness of 1.3μm after all kinds of stresses were neutralized,which is mainly originated from the interaction across grain boundaries.With increasing the thickness to 2.5μm and above it,the residual stress changed from tensile stresses to compressive stresses,and the compressive stress decreased with the thickness increased.These results could explain why a thicker KNN film can show improved electrical properties and the larger the thickness,the better the ferroelectric and piezoelectric properties.

Effect of Width-to-Thickness Ratio and Thickness Profile Changing on the Critical Instable Shape During Cold Strip Rolling

Based on the volume constancy with equal flow-per-second and elastic sheet stability theory, a coupling relationship among lateral thickness difference, width-to-thickness ratio of cold rolling strip steel under ideal and actual working conditions, and shape is concluded according to the comprehensive influence principle of various factors on the critical instable shape analyzed in-depth. Firstly, the influence model under actual working condition is developed by referring to the basic relationship between lateral thickness difference and shape under ideal condition. The test results prove that for thin strips with thickness below 0.3 mm, their lateral thickness differences have significant effect on the shape. After then, the combined influence of lateral thickness difference and width-to-thickness ratio on the critical instable shape is concluded according to the elastic sheet stability model, with the synthetic effect of these three factors analyzed. Test data indicate that for cold rolling strip steel with width-to-thickness ratio above 3 000, the critical instability stress difference decreases significantly. Actual measurements are conducted on the lateral thickness differences of two rolls of typical strip manufactured by a sixhigh cold mill, with the influence law of lateral thickness variation and width-to-thickness ratio comprehensively investigated. It is demonstrated that during the production of ultrathin strip steel with different width-to-thickness ratios, the loading roll shapes should be fine adjusted according to the lateral thickness difference of input strips.Therefore, the variation of lateral thickness difference of output strips can meet the requirement of shape stability,so as to obtain fine shape.