This study investigated the correlations between mechanical properties and mineralogy of granite using the digital image processing(DIP) and discrete element method(DEM). The results showed that the X-ray diffraction(...This study investigated the correlations between mechanical properties and mineralogy of granite using the digital image processing(DIP) and discrete element method(DEM). The results showed that the X-ray diffraction(XRD)-based DIP method effectively analyzed the mineral composition contents and spatial distributions of granite. During the particle flow code(PFC2D) model calibration phase, the numerical simulation exhibited that the uniaxial compressive strength(UCS) value, elastic modulus(E), and failure pattern of the granite specimen in the UCS test were comparable to the experiment. By establishing 351 sets of numerical models and exploring the impacts of mineral composition on the mechanical properties of granite, it indicated that there was no negative correlation between quartz and feldspar for UCS, tensile strength(σ_(t)), and E. In contrast, mica had a significant negative correlation for UCS, σ_(t), and E. The presence of quartz increased the brittleness of granite, whereas the presence of mica and feldspar increased its ductility in UCS and direct tensile strength(DTS) tests. Varying contents of major mineral compositions in granite showed minor influence on the number of cracks in both UCS and DTS tests.展开更多
A comprehensive understanding of spatial distribution and clustering patterns of gravels is of great significance for ecological restoration and monitoring.However,traditional methods for studying gravels are low-effi...A comprehensive understanding of spatial distribution and clustering patterns of gravels is of great significance for ecological restoration and monitoring.However,traditional methods for studying gravels are low-efficiency and have many errors.This study researched the spatial distribution and cluster characteristics of gravels based on digital image processing technology combined with a self-organizing map(SOM)and multivariate statistical methods in the grassland of northern Tibetan Plateau.Moreover,the correlation of morphological parameters of gravels between different cluster groups and the environmental factors affecting gravel distribution were analyzed.The results showed that the morphological characteristics of gravels in northern region(cluster C)and southern region(cluster B)of the Tibetan Plateau were similar,with a low gravel coverage,small gravel diameter,and elongated shape.These regions were mainly distributed in high mountainous areas with large topographic relief.The central region(cluster A)has high coverage of gravels with a larger diameter,mainly distributed in high-altitude plains with smaller undulation.Principal component analysis(PCA)results showed that the gravel distribution of cluster A may be mainly affected by vegetation,while those in clusters B and C could be mainly affected by topography,climate,and soil.The study confirmed that the combination of digital image processing technology and SOM could effectively analyzed the spatial distribution characteristics of gravels,providing a new mode for gravel research.展开更多
The modified atomic transformations are constructed and proved.On their basis the new complex analytic wavelets are obtained.The proof of the Fourier transforms existence in L1 and L2 on the basis of the theory of ato...The modified atomic transformations are constructed and proved.On their basis the new complex analytic wavelets are obtained.The proof of the Fourier transforms existence in L1 and L2 on the basis of the theory of atomic functions(AF)are presented.The numerical experiments of digital time series processing and physical analysis of the results confirm the efficiency of the proposed transforms.展开更多
We present an improved digital image processing(DIP)method to calculate the widths of single slits.Different from the traditional laser Fraunhofer diffraction experiment in college physical experiments,by performing f...We present an improved digital image processing(DIP)method to calculate the widths of single slits.Different from the traditional laser Fraunhofer diffraction experiment in college physical experiments,by performing fast Fourier transform,inverse fast Fourier transform and the nonlinear leastsquare fitting on the diffraction pattern taken by a camera,the DIP method can quickly return an analytic expression,whose period is used to calculate widths of single slits.By comparing the measured results by the DIP method and the successional difference(SD)method,we find that for a single slit whose width is 60372μm,the DIP method is more accurate.Experimental results show that for single slits with widths between 40μm and 160μm,the relative error of the DIP method is less than 2.78%.Also,the DIP method can be used to measure the diameter of filament and fibres online in real time.展开更多
A method of describing one-dimensional photonic crystals (1DPCs) based on Z-domain digital signal processing theory is presented. The analytical expression of the target band gap spectrum in the digital domain is ob...A method of describing one-dimensional photonic crystals (1DPCs) based on Z-domain digital signal processing theory is presented. The analytical expression of the target band gap spectrum in the digital domain is obtained by the autocorrelation of its impulse response. The feasibility of this method is verified by reconstructing two simple 1DPC structures with a target photonic band gap obtained by the traditional transfer matrix method. This method provides an effective approach to function-guided designs of interference-based band gap structures for photonic applications.展开更多
The soft robotics display huge advantages over their rigid counterparts when interacting with living organisms and fragile objects.As one of the most efficient actuators toward soft robotics,the soft pneumatic actuato...The soft robotics display huge advantages over their rigid counterparts when interacting with living organisms and fragile objects.As one of the most efficient actuators toward soft robotics,the soft pneumatic actuator(SPA)can produce large,complex responses with utilizing pressure as the only input source.In this work,a new approach that combines digital light processing(DLP)and injection-assisted post-curing is proposed to create SPAs that can realize different functionalities.To enable this,we develop a new class of photo-cross linked elastomers with tunable mechanical properties,good stretchability,and rapid curing speed.By carefully designing the geometry of the cavities embedded in the actuators,the resulting actuators can realize contracting,expanding,flapping,and twisting motions.In addition,we successfully fabricate a soft self-sensing bending actuator by injecting conductive liquids into the three-dimensional(3D)printed actuator,demonstrating that the present method has the potential to be used to manufacture intelligent soft robotic systems.展开更多
In this paper, we investigate advanced digital signal process ing (DSP) at the transmitter and receiver side for signal pre equalization and postequalization in order to improve spec trum efficiency (SE) and trans...In this paper, we investigate advanced digital signal process ing (DSP) at the transmitter and receiver side for signal pre equalization and postequalization in order to improve spec trum efficiency (SE) and transmission distance in an optical access network. A novel DSP scheme for this optical super Nyquist filtering 9 Quadrature Amplitude Modulation (9 QAM) like signals based on muhimodulus equalization with out post filtering is proposed. This scheme recovers the Ny quist filtered Quadrature PhaseShift Keying (QPSK) signal to a 9QAMlike one. With this technique, SE can be increased to 4 b/s/Hz for QPSK signals. A novel digital superNyquist signal generation scheme is also proposed to further suppress the Nyquist signal bandwidth and reduce channel crosstalk without the need for optical prefiltering. Only optical cou plers are needed for superNyquist wavelengthdivisionmulti plexing (WDM) channel multiplexing. We extend the DSP for shorthaul optical transmission networks by using highorder QAMs. We propose a highspeed Can'ierless Amplitude/Phase 64 QAM (CAP64 QAM) system using directly modulated la ser (DML) based on direct detection and digital equalization. Decisiondirected least mean square is used to equalize the CAP64QAM. Using this scheme, we generate and transmit up to 60 Gbit/s CAP64QAM over 20 km standard single mode fiber based on the DML and direct detection. Finally, several key problems are solved for real time orthogonalfre quencydivisionmultiplexing (OFDM) signal transmission aml processing. With coherent detection, up to 100 Glfit/s 16 QAMOFDM realtime transmission is possible.展开更多
A discrete model reference adaptive controller of robot arm is obtained by integrating the reduced dynamic model of robot, model reference adaptive control (MRAC) and digital signal processing (DSP) computer syste...A discrete model reference adaptive controller of robot arm is obtained by integrating the reduced dynamic model of robot, model reference adaptive control (MRAC) and digital signal processing (DSP) computer system into an electromechanical system. With the DSP computer system, the control signal of each joint of the robot arm can be processed in real time and independently. The simulation and experiment results show that with the control strategy, the robot achieved a good trajectory following precision, a good decoupling performance and a high real-time adaptivity.展开更多
In the first editorial of this two-part special issue, we pointed out that one of the biggest trends in wireless broadband, radar, sonar, and broadcasting technology is software RF processing and digital front-end [1]...In the first editorial of this two-part special issue, we pointed out that one of the biggest trends in wireless broadband, radar, sonar, and broadcasting technology is software RF processing and digital front-end [1]. Thistrend encompasses signal processing algorithms and integrated circuit design and includes digital pre-distortion (DPD), conversions between digital and analog signals, digita up-conversion (DUC), digital down-conversion (DDC), DC offset,展开更多
In recent years, explosively increasing data traffic has been boosting the con?tinuous demand of high speed optical interconnection inside or among data centers, high performance computers and even consumer electronic...In recent years, explosively increasing data traffic has been boosting the con?tinuous demand of high speed optical interconnection inside or among data centers, high performance computers and even consumer electronics. To pursue the improved intercon?nection performance of capacity, energy efficiency and simplicity, effective approaches are demonstrated including particularly advanced digital signal processing (DSP) meth?ods. In this paper, we present a review about the enabling adaptive DSP methods for opti?cal interconnection applications, and a detailed summary of our recent and ongoing works in this field. In brief, our works focus on dealing with the specific issues for short-reach interconnection scenarios with adaptive operation, including signal-to-noise-ratio (SNR) limitation, level nonlinearity distortion, energy efficiency consideration and the de?cision precision.展开更多
With the help of digital image processing technology, an automatic measurement method for the three-phase contact angles in the pore throats of the microfluidic model was established using the microfluidic water flood...With the help of digital image processing technology, an automatic measurement method for the three-phase contact angles in the pore throats of the microfluidic model was established using the microfluidic water flooding experiment videos as the data source. The results of the new method were verified through comparing with the manual measurement data.On this basis, the dynamic changes of the three-phase contact angles under flow conditions were clarified by the contact angles probability density curve and mean value change curve. The results show that, for water-wetting rocks, the mean value of the contact angles is acute angle during the early stage of the water flooding process, and it increases with the displacement time and becomes obtuse angle in the middle-late stage of displacement as the dominant force of oil phase gradually changes from viscous force to capillary force. The droplet flow in the remaining oil occurs in the central part of the pore throats, without three-phase contact angle. The contact angles for the porous flow and the columnar flow change slightly during the displacement and present as obtuse angles in view of mean values, which makes the remaining oil poorly movable and thus hard to be recovered. The mean value of the contact angle for the cluster flow tends to increase in the flooding process, which makes the remaining oil more difficult to be recovered. The contact angles for the membrane flow are mainly obtuse angles and reach the highest mean value in the late stage of displacement, which makes the remaining oil most difficult to be recovered. After displacement, the remaining oils under different flow regimes are just subjected to capillary force, with obtuse contact angles, and the wettability of the pore throat walls in the microfluidic model tends to be oil-wet under the action of crude oil.展开更多
This paper proposes the design and development of virtual experimental projects in the Digital Signal Processing course,using MATLAB,Proteus,and CCS platforms to develop a library of typical experimental cases for bio...This paper proposes the design and development of virtual experimental projects in the Digital Signal Processing course,using MATLAB,Proteus,and CCS platforms to develop a library of typical experimental cases for biomedical engineering majors and discusses the design process.Based on these typical cases,this paper explores the secondary design for innovative engineering practice case teaching,which can promote students’understanding and mastery of digital signal processing theories,algorithms,and technologies in an intuitive,flexible,and efficient way;quickly build new innovative engineering case models and further cultivate students’engineering application ability as well as innovative thinking.展开更多
Three-dimensional(3D)printing is an emerging technique that has shown promising success in engineering human tissues in recent years.Further development of vatphotopolymerization printing modalities has significantly ...Three-dimensional(3D)printing is an emerging technique that has shown promising success in engineering human tissues in recent years.Further development of vatphotopolymerization printing modalities has significantly enhanced the complexity level for 3D printing of various functional structures and components.Similarly,the development of microfluidic chip systems is an emerging research sector with promising medical applications.This work demonstrates the coupling of a digital light processing(DLP)printing procedure with a microfluidic chip system to produce size-tunable,3D-printable porosities with narrow pore size distributions within a gelatin methacryloyl(GelMA)hydrogel matrix.It is found that the generation of size-tunable gas bubbles trapped within an aqueous GelMA hydrogel-precursor can be controlled with high precision.Furthermore,the porosities are printed in two-dimensional(2D)as well as in 3D using the DLP printer.In addition,the cytocompatibility of the printed porous scaffolds is investigated using fibroblasts,where high cell viabilities as well as cell proliferation,spreading,and migration are confirmed.It is anticipated that the strategy is widely applicable in a range of application areas such as tissue engineering and regenerative medicine,among others.展开更多
Fabricating SiC ceramics via the digital light processing(DLP)technology is of great challenge due to strong light absorption and high refractive index of deep-colored SiC powders,which highly differ from those of res...Fabricating SiC ceramics via the digital light processing(DLP)technology is of great challenge due to strong light absorption and high refractive index of deep-colored SiC powders,which highly differ from those of resin,and thus significantly affect the curing performance of the photosensitive SiC slurry.In this paper,a thin silicon oxide(SiO_(2))layer was in-situ formed on the surface of SiC powders by pre-oxidation treatment.This method was proven to effectively improve the curing ability of SiC slurry.The SiC photosensitive slurry was fabricated with solid content of 55 vol%and viscosity of 7.77 Pa·s(shear rate of 30 s^(−1)).The curing thickness was 50μm with exposure time of only 5 s.Then,a well-designed sintering additive was added to completely convert low-strength SiO_(2) into mullite reinforcement during sintering.Complexshaped mullite-bond SiC ceramics were successfully fabricated.The flexural strength of SiC ceramics sintered at 1550℃in air reached 97.6 MPa with porosity of 39.2 vol%,as high as those prepared by spark plasma sintering(SPS)techniques.展开更多
The geometry of joints has a significant influence on the mechanical properties of rocks.To simplify the curved joint shapes in rocks,the joint shape is usually treated as straight lines or planes in most laboratory e...The geometry of joints has a significant influence on the mechanical properties of rocks.To simplify the curved joint shapes in rocks,the joint shape is usually treated as straight lines or planes in most laboratory experiments and numerical simulations.In this study,the computerized tomography (CT) scanning and photogrammetry were employed to obtain the internal and surface joint structures of a limestone sample,respectively.To describe the joint geometry,the edge detection algorithms and a three-dimensional (3D) matrix mapping method were applied to reconstruct CT-based and photogrammetry-based jointed rock models.For comparison tests,the numerical uniaxial compression tests were conducted on an intact rock sample and a sample with a joint simplified to a plane using the parallel computing method.The results indicate that the mechanical characteristics and failure process of jointed rocks are significantly affected by the geometry of joints.The presence of joints reduces the uniaxial compressive strength (UCS),elastic modulus,and released acoustic emission (AE) energy of rocks by 37%–67%,21%–24%,and 52%–90%,respectively.Compared to the simplified joint sample,the proposed photogrammetry-based numerical model makes the most of the limited geometry information of joints.The UCS,accumulative released AE energy,and elastic modulus of the photogrammetry-based sample were found to be very close to those of the CT-based sample.The UCS value of the simplified joint sample (i.e.38.5 MPa) is much lower than that of the CT-based sample (i.e.72.3 MPa).Additionally,the accumulative released AE energy observed in the simplified joint sample is 3.899 times lower than that observed in the CT-based sample.CT scanning provides a reliable means to visualize the joints in rocks,which can be used to verify the reliability of photogrammetry techniques.The application of the photogrammetry-based sample enables detailed analysis for estimating the mechanical properties of jointed rocks.展开更多
This paper describes the use of computer-aided measurement for external metric screw threads. Thread parameters, including thread pitch, thread angle, pitch diameter and major diameter, were measured with CCD cameras ...This paper describes the use of computer-aided measurement for external metric screw threads. Thread parameters, including thread pitch, thread angle, pitch diameter and major diameter, were measured with CCD cameras and image analysis software. New technologies such as digital image processing were used to increase the efficiency of measurements. In this study, by reconstructing the toolmaker’s microscope, the computer-aided semi-automated measuring system was developed, which could evaluate the accuracy of screw thread profile. It is concluded that the measurement accuracy is comparable to that of traditional toolmaker’s microscope method. Key words screw threads - quality inspection - accuracy - digital image processing展开更多
This article deals with two important issues in digital filter implementation: roundoff noise and limit cycles. A novel class of robust state-space realizations, called normal realizations, is derived and characteriz...This article deals with two important issues in digital filter implementation: roundoff noise and limit cycles. A novel class of robust state-space realizations, called normal realizations, is derived and characterized. It is seen that these realizations are free of limit cycles. Another interesting property of the normal realizations is that they yield a minimal error propagation gain. The optimal realization problem, defined as to find those normal realizations that minimize roundoff noise gain, is formulated and solved analytically. A design example is presented to demonstrate the behavior of the optimal normal realizations and to compare them with several well-known digital filter realizations in terms of minimizing the roundoff noise and the error propagation.展开更多
Although the structured light system that uses digital fringe projection has been widely implemented in three-dimensional surface profile measurement, the measurement system is susceptible to non-linear error. In this...Although the structured light system that uses digital fringe projection has been widely implemented in three-dimensional surface profile measurement, the measurement system is susceptible to non-linear error. In this work, we propose a convenient look-up-table-based (LUT-based) method to compensate for the non-linear error in captured fringe patterns. Without extra calibration, this LUT-based method completely utilizes the captured fringe pattern by recording the full-field differences. Then, a phase compensation map is established to revise the measured phase. Experimental results demonstrate that this method works effectively.展开更多
This paper introduced a welding machine for GMAW using digital controlling method based on DSP (Digital Signal Process). By means of flexible programming according to welding technologies and experiences the suitable ...This paper introduced a welding machine for GMAW using digital controlling method based on DSP (Digital Signal Process). By means of flexible programming according to welding technologies and experiences the suitable characteristics of welding machine, such as line compensation, welding voltage and current feedback, wire-feed driving, SCR trigging and so on, can be controlled and self-adjusted using digital signals. Through the designing based on DSP it is put out that the traditional hardware of control circuit is decreased greatly which can enhance the stability and reliability of welding machine. Finally, the welding experiment using CO 2 shielding gas proves that the welding process is stable.展开更多
基金This research was supported by the Department of Mining Engineering at the University of Utah.In addition,the lead author wishes to acknowledge the financial support received from the Talent Introduction Project,part of the Elite Program of Shandong University of Science and Technology(No.0104060540171).
文摘This study investigated the correlations between mechanical properties and mineralogy of granite using the digital image processing(DIP) and discrete element method(DEM). The results showed that the X-ray diffraction(XRD)-based DIP method effectively analyzed the mineral composition contents and spatial distributions of granite. During the particle flow code(PFC2D) model calibration phase, the numerical simulation exhibited that the uniaxial compressive strength(UCS) value, elastic modulus(E), and failure pattern of the granite specimen in the UCS test were comparable to the experiment. By establishing 351 sets of numerical models and exploring the impacts of mineral composition on the mechanical properties of granite, it indicated that there was no negative correlation between quartz and feldspar for UCS, tensile strength(σ_(t)), and E. In contrast, mica had a significant negative correlation for UCS, σ_(t), and E. The presence of quartz increased the brittleness of granite, whereas the presence of mica and feldspar increased its ductility in UCS and direct tensile strength(DTS) tests. Varying contents of major mineral compositions in granite showed minor influence on the number of cracks in both UCS and DTS tests.
基金funded by the National Natural Science Foundation of China(41971226,41871357)the Major Research and Development and Achievement Transformation Projects of Qinghai,China(2022-QY-224)the Strategic Priority Research Program of the Chinese Academy of Sciences(XDA28110502,XDA19030303).
文摘A comprehensive understanding of spatial distribution and clustering patterns of gravels is of great significance for ecological restoration and monitoring.However,traditional methods for studying gravels are low-efficiency and have many errors.This study researched the spatial distribution and cluster characteristics of gravels based on digital image processing technology combined with a self-organizing map(SOM)and multivariate statistical methods in the grassland of northern Tibetan Plateau.Moreover,the correlation of morphological parameters of gravels between different cluster groups and the environmental factors affecting gravel distribution were analyzed.The results showed that the morphological characteristics of gravels in northern region(cluster C)and southern region(cluster B)of the Tibetan Plateau were similar,with a low gravel coverage,small gravel diameter,and elongated shape.These regions were mainly distributed in high mountainous areas with large topographic relief.The central region(cluster A)has high coverage of gravels with a larger diameter,mainly distributed in high-altitude plains with smaller undulation.Principal component analysis(PCA)results showed that the gravel distribution of cluster A may be mainly affected by vegetation,while those in clusters B and C could be mainly affected by topography,climate,and soil.The study confirmed that the combination of digital image processing technology and SOM could effectively analyzed the spatial distribution characteristics of gravels,providing a new mode for gravel research.
文摘The modified atomic transformations are constructed and proved.On their basis the new complex analytic wavelets are obtained.The proof of the Fourier transforms existence in L1 and L2 on the basis of the theory of atomic functions(AF)are presented.The numerical experiments of digital time series processing and physical analysis of the results confirm the efficiency of the proposed transforms.
基金National Natural Science Foundtion of China(No.11435011)Young Teachers Fund of Nanjing Institute of Technology,China(Nos.QKJ201907 and QKJ201908)+2 种基金China Scholarship Council(No.201708320319)Postgraduate Research and Practice Innovation Program of Jiangsu Province,China(No.KYZZ16-0349)Qing Lan Project of Jiangsu Province,China。
文摘We present an improved digital image processing(DIP)method to calculate the widths of single slits.Different from the traditional laser Fraunhofer diffraction experiment in college physical experiments,by performing fast Fourier transform,inverse fast Fourier transform and the nonlinear leastsquare fitting on the diffraction pattern taken by a camera,the DIP method can quickly return an analytic expression,whose period is used to calculate widths of single slits.By comparing the measured results by the DIP method and the successional difference(SD)method,we find that for a single slit whose width is 60372μm,the DIP method is more accurate.Experimental results show that for single slits with widths between 40μm and 160μm,the relative error of the DIP method is less than 2.78%.Also,the DIP method can be used to measure the diameter of filament and fibres online in real time.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.10804070 and 61137002)the Key Program of the Science and Technology Commission of Shanghai,China(Grant No.11jc1413300)the Shanghai Leading Academic Discipline Project,China(Grant No.S30108)
文摘A method of describing one-dimensional photonic crystals (1DPCs) based on Z-domain digital signal processing theory is presented. The analytical expression of the target band gap spectrum in the digital domain is obtained by the autocorrelation of its impulse response. The feasibility of this method is verified by reconstructing two simple 1DPC structures with a target photonic band gap obtained by the traditional transfer matrix method. This method provides an effective approach to function-guided designs of interference-based band gap structures for photonic applications.
基金the National Natural Science Foundation of China(Nos.11572002 and 12002032)the China Postdoctoral Science Foundation(Nos.BX20200056 and 2020M670149)。
文摘The soft robotics display huge advantages over their rigid counterparts when interacting with living organisms and fragile objects.As one of the most efficient actuators toward soft robotics,the soft pneumatic actuator(SPA)can produce large,complex responses with utilizing pressure as the only input source.In this work,a new approach that combines digital light processing(DLP)and injection-assisted post-curing is proposed to create SPAs that can realize different functionalities.To enable this,we develop a new class of photo-cross linked elastomers with tunable mechanical properties,good stretchability,and rapid curing speed.By carefully designing the geometry of the cavities embedded in the actuators,the resulting actuators can realize contracting,expanding,flapping,and twisting motions.In addition,we successfully fabricate a soft self-sensing bending actuator by injecting conductive liquids into the three-dimensional(3D)printed actuator,demonstrating that the present method has the potential to be used to manufacture intelligent soft robotic systems.
基金supported by the High Technology Research and Development Program of China("863"Program)under Grant No.2012AA011303 and 2013AA010501National Nature Science Foundation of China under Grant No.61325002
文摘In this paper, we investigate advanced digital signal process ing (DSP) at the transmitter and receiver side for signal pre equalization and postequalization in order to improve spec trum efficiency (SE) and transmission distance in an optical access network. A novel DSP scheme for this optical super Nyquist filtering 9 Quadrature Amplitude Modulation (9 QAM) like signals based on muhimodulus equalization with out post filtering is proposed. This scheme recovers the Ny quist filtered Quadrature PhaseShift Keying (QPSK) signal to a 9QAMlike one. With this technique, SE can be increased to 4 b/s/Hz for QPSK signals. A novel digital superNyquist signal generation scheme is also proposed to further suppress the Nyquist signal bandwidth and reduce channel crosstalk without the need for optical prefiltering. Only optical cou plers are needed for superNyquist wavelengthdivisionmulti plexing (WDM) channel multiplexing. We extend the DSP for shorthaul optical transmission networks by using highorder QAMs. We propose a highspeed Can'ierless Amplitude/Phase 64 QAM (CAP64 QAM) system using directly modulated la ser (DML) based on direct detection and digital equalization. Decisiondirected least mean square is used to equalize the CAP64QAM. Using this scheme, we generate and transmit up to 60 Gbit/s CAP64QAM over 20 km standard single mode fiber based on the DML and direct detection. Finally, several key problems are solved for real time orthogonalfre quencydivisionmultiplexing (OFDM) signal transmission aml processing. With coherent detection, up to 100 Glfit/s 16 QAMOFDM realtime transmission is possible.
文摘A discrete model reference adaptive controller of robot arm is obtained by integrating the reduced dynamic model of robot, model reference adaptive control (MRAC) and digital signal processing (DSP) computer system into an electromechanical system. With the DSP computer system, the control signal of each joint of the robot arm can be processed in real time and independently. The simulation and experiment results show that with the control strategy, the robot achieved a good trajectory following precision, a good decoupling performance and a high real-time adaptivity.
文摘In the first editorial of this two-part special issue, we pointed out that one of the biggest trends in wireless broadband, radar, sonar, and broadcasting technology is software RF processing and digital front-end [1]. Thistrend encompasses signal processing algorithms and integrated circuit design and includes digital pre-distortion (DPD), conversions between digital and analog signals, digita up-conversion (DUC), digital down-conversion (DDC), DC offset,
基金supported by the National Natural Science Foundation of China(Grant No51079043)the Special Fund for Public Welfare Industry of Ministry of Water Resources of China(Grants No200901064 and 201001020)the Research Innovation Program for College Graduates of Jiangsu Province(Grant No CXZZ11_0450)
基金This work was supported by National Natural Science Foundation of Chi⁃na(NSFC)under Grant Nos.61935011,61875124 and 61875049.
文摘In recent years, explosively increasing data traffic has been boosting the con?tinuous demand of high speed optical interconnection inside or among data centers, high performance computers and even consumer electronics. To pursue the improved intercon?nection performance of capacity, energy efficiency and simplicity, effective approaches are demonstrated including particularly advanced digital signal processing (DSP) meth?ods. In this paper, we present a review about the enabling adaptive DSP methods for opti?cal interconnection applications, and a detailed summary of our recent and ongoing works in this field. In brief, our works focus on dealing with the specific issues for short-reach interconnection scenarios with adaptive operation, including signal-to-noise-ratio (SNR) limitation, level nonlinearity distortion, energy efficiency consideration and the de?cision precision.
基金Supported by National Science and Technology Major Project of China (51674271)Major Technical Field Test of PetroChina (2019F-33)。
文摘With the help of digital image processing technology, an automatic measurement method for the three-phase contact angles in the pore throats of the microfluidic model was established using the microfluidic water flooding experiment videos as the data source. The results of the new method were verified through comparing with the manual measurement data.On this basis, the dynamic changes of the three-phase contact angles under flow conditions were clarified by the contact angles probability density curve and mean value change curve. The results show that, for water-wetting rocks, the mean value of the contact angles is acute angle during the early stage of the water flooding process, and it increases with the displacement time and becomes obtuse angle in the middle-late stage of displacement as the dominant force of oil phase gradually changes from viscous force to capillary force. The droplet flow in the remaining oil occurs in the central part of the pore throats, without three-phase contact angle. The contact angles for the porous flow and the columnar flow change slightly during the displacement and present as obtuse angles in view of mean values, which makes the remaining oil poorly movable and thus hard to be recovered. The mean value of the contact angle for the cluster flow tends to increase in the flooding process, which makes the remaining oil more difficult to be recovered. The contact angles for the membrane flow are mainly obtuse angles and reach the highest mean value in the late stage of displacement, which makes the remaining oil most difficult to be recovered. After displacement, the remaining oils under different flow regimes are just subjected to capillary force, with obtuse contact angles, and the wettability of the pore throat walls in the microfluidic model tends to be oil-wet under the action of crude oil.
基金the 2021 Experimental Teaching Reform Project of Shanghai University of Medicine&Health Sciences“Digital Signal Processing Course Design”(Project Number:JG(21)04-B4-02).
文摘This paper proposes the design and development of virtual experimental projects in the Digital Signal Processing course,using MATLAB,Proteus,and CCS platforms to develop a library of typical experimental cases for biomedical engineering majors and discusses the design process.Based on these typical cases,this paper explores the secondary design for innovative engineering practice case teaching,which can promote students’understanding and mastery of digital signal processing theories,algorithms,and technologies in an intuitive,flexible,and efficient way;quickly build new innovative engineering case models and further cultivate students’engineering application ability as well as innovative thinking.
基金National Science Centre Poland(NCN),Grant/Award Number:2020/37/B/ST8/02167European Union’s Horizon 2020 research and innovation program,Grant/Award Number:813786+2 种基金National Institutes of Health,Grant/Award Number:R21EB025270National Science Foundation,Grant/Award Number:CBET-EBMS-1936105Brigham Research Institute。
文摘Three-dimensional(3D)printing is an emerging technique that has shown promising success in engineering human tissues in recent years.Further development of vatphotopolymerization printing modalities has significantly enhanced the complexity level for 3D printing of various functional structures and components.Similarly,the development of microfluidic chip systems is an emerging research sector with promising medical applications.This work demonstrates the coupling of a digital light processing(DLP)printing procedure with a microfluidic chip system to produce size-tunable,3D-printable porosities with narrow pore size distributions within a gelatin methacryloyl(GelMA)hydrogel matrix.It is found that the generation of size-tunable gas bubbles trapped within an aqueous GelMA hydrogel-precursor can be controlled with high precision.Furthermore,the porosities are printed in two-dimensional(2D)as well as in 3D using the DLP printer.In addition,the cytocompatibility of the printed porous scaffolds is investigated using fibroblasts,where high cell viabilities as well as cell proliferation,spreading,and migration are confirmed.It is anticipated that the strategy is widely applicable in a range of application areas such as tissue engineering and regenerative medicine,among others.
基金supported by Shandong University−MSEA International Institute for Materials Genome Joint Innovation Center for Advanced Ceramics,and the Key Research and Development Projects of Shaanxi Province(Nos.2018ZDCXLGY-09-06 and 2021ZDLGY14-06).
文摘Fabricating SiC ceramics via the digital light processing(DLP)technology is of great challenge due to strong light absorption and high refractive index of deep-colored SiC powders,which highly differ from those of resin,and thus significantly affect the curing performance of the photosensitive SiC slurry.In this paper,a thin silicon oxide(SiO_(2))layer was in-situ formed on the surface of SiC powders by pre-oxidation treatment.This method was proven to effectively improve the curing ability of SiC slurry.The SiC photosensitive slurry was fabricated with solid content of 55 vol%and viscosity of 7.77 Pa·s(shear rate of 30 s^(−1)).The curing thickness was 50μm with exposure time of only 5 s.Then,a well-designed sintering additive was added to completely convert low-strength SiO_(2) into mullite reinforcement during sintering.Complexshaped mullite-bond SiC ceramics were successfully fabricated.The flexural strength of SiC ceramics sintered at 1550℃in air reached 97.6 MPa with porosity of 39.2 vol%,as high as those prepared by spark plasma sintering(SPS)techniques.
基金supported by the National Natural Science Foundation of China(Grant Nos.42277150,41977219)Henan Provincial Science and Technology Research Project(Grant No.222102320271).
文摘The geometry of joints has a significant influence on the mechanical properties of rocks.To simplify the curved joint shapes in rocks,the joint shape is usually treated as straight lines or planes in most laboratory experiments and numerical simulations.In this study,the computerized tomography (CT) scanning and photogrammetry were employed to obtain the internal and surface joint structures of a limestone sample,respectively.To describe the joint geometry,the edge detection algorithms and a three-dimensional (3D) matrix mapping method were applied to reconstruct CT-based and photogrammetry-based jointed rock models.For comparison tests,the numerical uniaxial compression tests were conducted on an intact rock sample and a sample with a joint simplified to a plane using the parallel computing method.The results indicate that the mechanical characteristics and failure process of jointed rocks are significantly affected by the geometry of joints.The presence of joints reduces the uniaxial compressive strength (UCS),elastic modulus,and released acoustic emission (AE) energy of rocks by 37%–67%,21%–24%,and 52%–90%,respectively.Compared to the simplified joint sample,the proposed photogrammetry-based numerical model makes the most of the limited geometry information of joints.The UCS,accumulative released AE energy,and elastic modulus of the photogrammetry-based sample were found to be very close to those of the CT-based sample.The UCS value of the simplified joint sample (i.e.38.5 MPa) is much lower than that of the CT-based sample (i.e.72.3 MPa).Additionally,the accumulative released AE energy observed in the simplified joint sample is 3.899 times lower than that observed in the CT-based sample.CT scanning provides a reliable means to visualize the joints in rocks,which can be used to verify the reliability of photogrammetry techniques.The application of the photogrammetry-based sample enables detailed analysis for estimating the mechanical properties of jointed rocks.
文摘This paper describes the use of computer-aided measurement for external metric screw threads. Thread parameters, including thread pitch, thread angle, pitch diameter and major diameter, were measured with CCD cameras and image analysis software. New technologies such as digital image processing were used to increase the efficiency of measurements. In this study, by reconstructing the toolmaker’s microscope, the computer-aided semi-automated measuring system was developed, which could evaluate the accuracy of screw thread profile. It is concluded that the measurement accuracy is comparable to that of traditional toolmaker’s microscope method. Key words screw threads - quality inspection - accuracy - digital image processing
基金the National Nature Science Foundation of China (60774021)
文摘This article deals with two important issues in digital filter implementation: roundoff noise and limit cycles. A novel class of robust state-space realizations, called normal realizations, is derived and characterized. It is seen that these realizations are free of limit cycles. Another interesting property of the normal realizations is that they yield a minimal error propagation gain. The optimal realization problem, defined as to find those normal realizations that minimize roundoff noise gain, is formulated and solved analytically. A design example is presented to demonstrate the behavior of the optimal normal realizations and to compare them with several well-known digital filter realizations in terms of minimizing the roundoff noise and the error propagation.
基金the financial support provided by the National Natural Science Foundation of China(11472267 and 11372182)the National Basic Research Program of China(2012CB937504)
文摘Although the structured light system that uses digital fringe projection has been widely implemented in three-dimensional surface profile measurement, the measurement system is susceptible to non-linear error. In this work, we propose a convenient look-up-table-based (LUT-based) method to compensate for the non-linear error in captured fringe patterns. Without extra calibration, this LUT-based method completely utilizes the captured fringe pattern by recording the full-field differences. Then, a phase compensation map is established to revise the measured phase. Experimental results demonstrate that this method works effectively.
文摘This paper introduced a welding machine for GMAW using digital controlling method based on DSP (Digital Signal Process). By means of flexible programming according to welding technologies and experiences the suitable characteristics of welding machine, such as line compensation, welding voltage and current feedback, wire-feed driving, SCR trigging and so on, can be controlled and self-adjusted using digital signals. Through the designing based on DSP it is put out that the traditional hardware of control circuit is decreased greatly which can enhance the stability and reliability of welding machine. Finally, the welding experiment using CO 2 shielding gas proves that the welding process is stable.