A 5MS/s 12-Bit Successive Approximation Analog-to-Digital Converter

With the continuous development of science and technology, digital signal processing is more and more widely used in various fields. Among them, the analog-to-digital converter (ADC) is one of the key components to convert analog signals to digital signals. As a common type of ADC, 12-bit sequential approximation analog-to-digital converter (SAR ADC) has attracted extensive attention for its performance and application. This paper aims to conduct in-depth research and analysis of 12-bit SAR ADC to meet the growing demands of digital signal processing. This article designs a 12-bit, successive approximation analog-to-digital converter (SAR ADC) with a sampling rate of 5 MS/s. The overall circuit adopts a fully differential structure, with key modules including DAC capacitor array, comparator, and control logic. According to the DAC circuit in this paper, a fully differential capacitor DAC array structure is proposed to reduce the area of layout DAC. The comparator uses a digital dynamic comparator to improve the ADC conversion speed. The chip is designed based on the SMIC180 nm CMOS process. The simulation results show that when the sampling rate is 5 MS/s, the effective bit of SAR ADC is 11.92 bit, the SNR is 74.62 dB, and the SFDR is 89.24 dB.

ADC border effect and suppression of quantization error in the digital dynamic measurement

The digital measurement and processing is an important direction in the measurement and control field. The quantization error widely existing in the digital processing is always the decisive factor that restricts the development and applications of the digital technology. In this paper, we find that the stability of the digital quantization system is obviously better than the quantization resolution. The application of a border effect in the digital quantization can greatly improve the accuracy of digital processing. Its effective precision has nothing to do with the number of quantization bits, which is only related to the stability of the quantization system. The high precision measurement results obtained in the low level quantization system with high sampling rate have an important application value for the progress in the digital measurement and processing field.

Simulation and Design Optimization of Novel Microelectromechanical Digital-to-Analog Converter

A microelectromechanical Digital to Analog Converter (DAC) based on Weighted Gap (WG) principle is described,which is analogous to the weighed resistor DAC in electronic circuits.To convert the input of binary voltage to the output of analog displacement,the gaps are proposed to be employed as a scale factor.A finite element method is used to simulate the performance of the DAC.To reduce the error,the structure design is optimized and the maximum error of 0 002μm is obtained.

A high precision time-to-digital converter based on multi-phase clock implemented within Field-Programmable-Gate-Array

In this paper, the design of a coarse-fine interpolation Time-to-Digital Converter (TDC) is implemented in an ALTERA’s Cyclone FPGA. The carry-select chain performs as the tapped delay line. The Logic Array Block (LAB) having a propagation delay of 165 ps in the chain is synthesized as delay cell. Coarse counters triggered by the global clock count the more significant bits of the time data. This clock is also fed through the delay line, and LABs create the copies. The replicas are latched by the tested event signal, and the less significant bits are encoded from the latched binary bits. Single-shot resolution of the TDC can be 60 ps. The worst Differential Nonlinearity (DNL) is about 0.2 Least Significant Bit (LSB, 165 ps in this TDC module), and the Integral Nonlinearity (INL) is 0.6 LSB. In comparison with other architectures using the synchronous global clock to sample the taps, this architecture consumed less electric power and logic cells, and is more stable.

Development of OPTO-LDR coupled timer based voltage to frequency converter

This paper describes the development of a timer based voltage to frequency converter(V FC).Timer LM555is used in astable multivibrator mode with two OPTO-LDRs(light dependent resistors)in the circuitry.The frequency of timer output waveform which is measured using a digital storage oscillator(DSO)is almost linearly proportional to the applied input voltage.Hence we obtain a linear relationship between the frequency of timer output waveform and the input voltage.Because of its quasi-digital output,the main advantages of this developed converter are linear input-output relationship,small size,easy portabilityand high cost performance.In addition,the timer output waveform can be directly interfaced with personal computer or microprocessor/microcontroller for further processing of the input voltage signal without intervening any analog-to-digital converter(ADC).

Overview of Energy-Efficient Successive-Approximation Analog-to-Digital Converters: State-of-the-Art and a Design Example

This paper makes a review of state-of-the- arts designs of successive-approximation register analog-to-digital converters （SAR ADCs）. Methods and technique specifications are collected in view of innovative ideas. At the end of this paper, a design example is given to illustrate the procedure to design an SAR ADC. A new method, which extends the width of the internal clock, is also proposed to facilitate different sampling frequencies, which provides more time for the digital-to-analog convert （DAC） and comparator to settle. The 10 bit ADC is simulated in 0.13 μm CMOS process technology. The signal-to-noise and distortion ratio （SNDR） is 54.41 dB at a 10 MHz input with a 50 MS/s sampling rate, and the power is 330 μW.

Design of low-power high-frequency digital controlled DC-DC switching power converter

This paper models a low-power high-frequency digitally controlled synchronous rectifier （SR） OUCK converter. The converter is a hybrid system with three operation modes. Digital PID controler is used. Key problems such as quantization resolution of digital pulse-width modulation （DPWM） and steady-state limit cycles of digital control switching model power supply （SMPS） are discussed, with corresponding solutions presented. Simulation of a digital control synchronous buck is performed with a fixed-point algorithm. The results show that the described approach enables high-speed dynamic performance.

A LOW POWER TIME-TO-DIGITAL CONVERTER FOR ALL-DIGITAL PHASE-LOCKED LOOP

Time-to-Digital Converter (TDC) is a key block used as the phase/frequency detector in an All-Digital Phase-Locked Loop (ADPLL). Usually, it occupies a large proportion of ADPLL's total power consumption up to about 30% to 40%. In this paper, the detailed power consumption of different components in the TDC is analyzed. A Power Management Block (PMB) is presented for the TDC to reduce its power consumption. A 24-bits TDC core with the proposed PMB is implemented in HJTC 0.18 μm CMOS technology. Simulation results show that up to 84% power reduction is achieved using our proposed technique.

Design and Implementation of a Portable Computer Based Induction Motor Supervisory System

The aim of this research paper is to monitor an inductionmotor (single or three-phase) while working or running using a portable computer. Parameters measured include supply voltage, stator coli temperature and casing temperature. For the temperatures of both stator and casing, temperature sensors were used. The sensor senses the temperature and sends its output to the analogue to the digital integrated circuit for further processing. The supply voltage is also moni-tored by a circuit and integrated circuit. The project on completion was tested and the parameters displayed on the portable computer. The objectives of the project are: The supply system can measure the following parameters: supply voltage, stator coil temperature, casing temperature. Display the data on the PC screen with the possibility of settings to establish range, limits and alarm indicators when these are exceeded. The program should be able to save data of the log entry with time on a dedicated file as record for future analysis.

Design of Digital to Analog Converters with Arbitrary Radix

There are DAC structures available in the literature for radix r = 2, 3, and 4;but how they are arrived at is missing. No general structure is available for any radix r. The aim of the paper is, therefore, to fulfil these gaps. To start with, the design relations are derived for the simplest possible attenuator circuit when connected to a voltage source V and a series resistance R, such that the complete circuit offers the Thevenin resistance R. Spread relations for this attenuator are derived. An example when 3 such attenuators with different attenuation constants are connected in cascade is given. Interestingly, the two attenuators with attenuation factors 1/2 and 1/3 have the same spread of 2. A generalized attenuator is then obtained when N number of identical attenuators are connected in cascade. This is modified to derive a digital to analog converter for any radix r.

Effect of ionizing radiation on dual 8-bit analog-to-digital converters (AD9058) with various dose rates and bias conditions

The radiation effects on several properties （reference voltage, digital output logic voltage, and supply current） of dual 8-bit analog-to-digital （A/D） converters （AD9058） under various biased conditions are investigated in this paper. Gamma ray and 10-MeV proton irradiation are selected for a detailed evaluation and comparison. Based on the measurement results induced by the gamma ray with various dose rates, the devices exhibit enhanced low dose rate sensitivity （ELDRS） under zero and working bias conditions. Meanwhile, it is obvious that the ELDRS is more severe under the working bias condition than under the zero bias condition. The degradation of AD9058 does not display obvious ELDRS during 10-MeV proton irradiation with the selected flux.

A 1.5 bit/s Pipelined Analog-to-Digital Converter Design with Independency of Capacitor Mismatch

A new technique which is named charge temporary storage technique (CTST) was presented to improve the linearity of a 1.5 bit/s pipelined analog-to-digital converter (ADC). The residual voltage was obtained from the sampling capacitor, and the other capacitor was just a temporary storage of charge. Then, the linearity produced by the mismatch of these capacitors was eliminated without adding extra capacitor error-averaging amplifiers. The simulation results confirmed the high linearity and low dissipation of pipelined ADCs implemented in CTST, so CTST was a new method to implement high resolution, small size ADCs.

Novel Optical Analog-To-Digital Converter Based on Optical Time Division Multiplexing

A novel optical analog-to-digital converter based on optical time division multiplexing(OTDM) is described which uses electrooptic sampling and time-demultiplexing together with multiple electronic analog-to-digital converter(ADC). Compared with the previous scheme, the time-division multiplexer and the time-division demultiplexer are applied in the optical analog-to-digital converter(OADC) at the same time, the design of the OADC is simplified and the performance of the OADC based on time-division demultiplexer is improved. A core optical part of the system is demonstrated with a sample rate of 10 Gs/s. The signals in three channels are demultiplexed from the optical pulses.The result proves our scheme is feasible.

Digital Control Technologies for DC/DC Switching Converters

An overview of recent advances in digital control of low-to medium-power DC/DC switching converters is presented.Traditionally,analog electronics methods have dominated in controlling such DC/DC converters.However,with the steadily decreasing cost of ICs,the feasibility of digitally controlled DC/DC switching converters has increased sig-nificantly.This paper outlines a sample of digital solutions for DC/DC switching converters to enhance the performance of DC/DC switching converters.Furthermore,latest research activities pertaining to applications for steady-state and dy-namic performance improvement,such as efficiency optimization,controller auto tuning,and capacitor charge balance control,is discussed.These applications demonstrate the significant advantages and potentials of digital control.

Single-Stage Vernier Time-to-Digital Converter with Sub-Gate Delay Time Resolution

This paperpresents a single-stage Vernier Time-to-Digital Converter (VTDC) that utilizes the dynamic-logic phase detector. The zero dead-zone characteristic of this phase detector allows for the single-stage VTDC to deliver sub-gate delay time resolution. The single-stage VTDC has been designed in 0.13μm CMOS technology. The simulation results demonstrate a linear input-output characteristic for input dynamic range from 0 to 1.6ns with a time resolution of 25ps.

Performance Evaluation of Wavelength Division Multiplexing Photonic Analogue-to-Digital Converters for High-Resolution Radar Systems

The performance of the wavelength division multiplexing (WDM) photonic analogue-to-digital converter (ADC) used for digitization of high-resolution radar systems is evaluated numerically by using the peak signal-to-noise ratio (SNR) metric. Two different WDM photonic ADC architectures are considered for the digitization of radar signals with 5 GHz of bandwidth (spatial resolution of 3 cm), in order to provide a comprehensive study of the compromises present when deploying radar signals with high-resolution: 1) a four-channel architecture with each channel employing an ADC with 5 GSamples/s, and 2) an eight-channel architecture with each channel employing an ADC with 2.5 GSamples/s. For peak powers of the pulsed source between 10 and 20 dBm and a distance between the radar antenna and the sensing object of 2.4 meters, peak SNR levels between 29 and 39 dB are achieved with the eight-channel architecture, which shows higher peak SNR levels when compared with the four-channel architecture. For the eight-channel architecture and for the same peak powers of the pulsed source, peak SNR levels between 11 and 16 dB are obtained when the distance increases to 13.5 meters. With this evaluation using the peak SNR, it is possible to assess the performance limits when choosing a specific radar range, while keeping the same resolution.

PULSE SHRINKING TIME-TO-DIGITAL CONVERTER FOR UWB APPLICATION

A kind of architecture of Time-to-Digital Converter(TDC) for Ultra-WideBand(UWB) application is presented. The proposed TDC is based on pulse shrinking, and implemented in a Field Programmable Gate Array(FPGA) device. The pulse shrinking is realized in a loop containing two Programmable Delay Lines(PDLs) or a two-channel PDL. One line(channel) delays the rising edge and the other line(channel) delays the falling edge of a circulating pulse. Delay resolution of PDL is converted into a digital output code under known conditions of pulse width. This delay resolution measurement mechanism is different from the conventional time interval measurement mechanism based on pulse shrinking of conversion of unknown pulse width into a digital output code. This mechanism automatically avoids the influence of unwanted pulse shrinking by any circuit element apart from the lines. The achieved relative errors for four PDLs are within 0.80%–1.60%.

一种基于分数阶微积分的CCM Boost变换器准在线无源参数的数字孪生辨识方法

由于具有高性价比、准确性和数字化等优点,数字孪生已成为电力电子变换器故障趋势判断和预知维护的先进技术。针对当前电力电子变换器所建立的数字孪生模型尚未考虑实际电感、电容的分数阶特性的问题,基于分数阶微积分构建电力电子电路的预估-校正数字孪生模型,应用基于粒子群优化(particle swarm optimization,PSO)算法的孪生参数辨识方法对不同分数阶阶次下的电感值(L)和电容值(C)进行辨识,并计算出等效串联电阻。通过与现有方法对比,该方法不仅提高了实际电感和实际电容的辨识精度,还能辨识出不同阶次下与不同C下的分数阶参数。最后,搭建不同L和C及分数阶阶次的连续导通模式Boost变换器物理样机,并考虑不同工况条件与不同辨识次数等因素来进行实验验证。实验结果验证了所提模型与方法的有效性。

基于0.18μm SiGe BiCMOS工艺的4GS/s、14 bit数模转换器

基于0.18μm SiGe BiCMOS工艺,设计了超高速高精度数模转换器(DAC),其时钟采样率为4 GS/s、精度为14 bit。为满足4 GHz处理速度,该DAC中所有电路均采用异质结晶体管(HBTs)搭建。为了降低功耗和节约面积,本设计采用10+4分段译码的方式,其中低10位电流舵使用R-2R梯形电阻网络,而高4位使用温度计码结构。仿真结果表明,所设计DAC的DNL、INL分别为0.54 LSB和0.39 LSB,全奈奎斯特频域内的无杂散动态范围均大于82 dBc。在3.3 V和5 V混合电源供电下,整个DAC的平均功耗为2.39 W。芯片总面积为11.22 mm^(2)。

基于时钟抖动流水线结构的高效率真随机数发生器

现代加密系统对密钥随机性的需求不断增加。使用时序抖动、热噪声、亚稳态等作为熵源的真随机数发生器,因其可以提供高质量的随机性成为该领域的研究热点。因此,提出一种可配置、轻量级、高效率的真随机数发生器。该发生器使用基于随机数学模型的设计方法,由差分构架的两级时钟抖动流水线组成。第一级流水线中两个环形振荡器在规定时间内累积抖动,第二级流水线利用近似相同的两个环形振荡器的微小周期差构建时间数字转换器,对第一级输出的高斯抖动进行量化,通过数字化模块输出随机比特。在时间数字转换器运行过程中,第一级流水线已经重新启动累积下一个阶段的抖动,减少了空闲时间,提高了真随机数的质量和效率。在Xilinx Atrix-7平台进行了验证,该结构的硬件资源仅消耗了25个LUTs和13个DFFs,获得高达32.55 Mb/s的吞吐量。