Pushing the boundaries of diode-pumped solid-state lasers for high-energy applications

We report on the successful demonstration of a 150 J nanosecond pulsed cryogenic gas cooled,diode-pumped multi-slab Yb:YAG laser operating at 1 Hz.To the best of our knowledge,this is the highest energy ever recorded for a diodepumped laser system.

A 54-fs diode-pumped Kerr-lens mode-locked Yb:LuYSiO_(5) laser

We demonstrate a Kerr-lens mode-locked Yb:Lu YSiO_(5)(Yb:LYSO)laser with the pulse duration of 54 fs,corresponding to a spectral bandwidth of 25 nm centered at 1062 nm.To the best of our knowledge,this is the shortest pulse duration obtained from Yb:LYSO laser.At the repetition rate of 378.3 MHz,an output power of 111.6 m W is obtained using an output coupler with 0.6%transmittance,which can maintain long-time stable mode-locking more than 13 h.

Diode-Pumped Passively Mode-Locked 1079 nm Nd:CaGdAlO_4 Laser

We demonstrate a diode-pumped passively cw mode-locked Nd：CaGdAlO4 laser operating at 1079nm with a semiconductor saturable absorber mirror for the first time to the best of our knowledge. The threshold pump power of the laser is 180mW. A maximum average output power of 93mW is obtained under the pump power of 1.94 W. The pulse duration of the mode-locked pulses is 3.1ps and the repetition rate is 157MHz.

Continuous-Wave and Actively Q-Switched Diode-Pumped Er:LuAG Ring Laser at 1650 nm

We demonstrate a cw and actively Q-switched Er：LuAO laser resonantly dual-end-pumped by 1532nm fibre- coupled laser diodes. A maximum cw output power of 1.9W at 1650.3nm is obtained at a pump power of 25.5 W, corresponding to a slope efficiency of 43.3 %. In the Q-switched regime, the maximum pulse energy of 3.51 mJ is reached at a pulse repetition rate of 100 Hz, a pulse duration of 90.5ns and a pump power of 25.5 W. At the repetition rate of 400 Hz, the output energy is 2.12m J, corresponding to a pulse duration of 125.4 ns.

Diode-pumped laser performance of Tm:Sc2SiO5 crystal at 1971 nm

The 4-at.% Tm：Sc_2SiO_5 （Tm：SSO） crystal is successfully obtained by the Czochralski method. The optical properties and thermal conductivity of the crystal are investigated. The broad continuous wave（CW） laser output of（100）-cut Tm：SSO with the dimensions of 3 mm×3 mm×3 mm under laser diode（LD）-pumping is realized. The full width at half maximum（FWHM） of the laser emitting reaches up to 21 nm. The laser threshold of Tm：SSO is measured to be 0.43 W. Efficient diode-pumped CW laser performance of Tm：SSO is demonstrated with a slope efficiency of 25.9% and maximum output power of 934 mW.

Diode-Pumped Passive Q-Switched 946 nm Nd：YAG Laser with a GaAs Saturable Absorber

We report, for the first time to our knowledge, a diode-pumped passive Q-switched 946nm Nd：YAG laser by using a GaAs as saturable absorber. The maximum average output power is 1.24 W at an incident pump power of 15 W, corresponding to a slope efficiency of 10%. Laser pulses with pulse duration of 70ns and repetition rate of 330 kHz are generated.

Analytical modelling of end thermal coupling in a solid-state laser longitudinally bonded by a vertical-cavity top-emitting laser diode

The intrinsic features involving a circularly symmetric beam profile with low divergence, planar geometry as well as the increasingly enhanced power of vertical-cavity surface-emitting lasers （VCSELs） have made the VCSEL a promising pump source in direct end bonding to a solid-state laser medium to form the minimized, on-wafer integrated laser system. This scheme will generate a surface contact pump configuration and thus additional end thermal coupling to the laser medium through the joint interface of both materials, apart from pump beam heating. This paper analytically models temperature distributions in both VCSEL and the laser medium from the end thermal coupling regarding surface contact pump configuration using a top-emitting VCSEL as the pump source for the first time. The analytical solutions are derived by introducing relative temperature and mean temperature expressions. The results show that the end contact heating by the VCSEL could lead to considerable temperature variations associated with thermal phase shift and thermal lensing in the laser medium. However, if the central temperature of the interface is increased by less than 20 K, the end contact heating does not have a significant thermal influence on the laser medium. In this case, the thermal effect should be dominated by pump beam heating. This work provides useful analytical results for further analysis of hybrid thermal effects on those lasers pumped by a direct VCSEL bond.

Efficient Diode-Pumped Actively Q-Switched Ceramic Nd:YAG/YVO4 Raman Laser Operating at 1657 nm

A diode-pumped actively Q-switched Raman laser is demonstrated, with YV04 employed as Raman active medium, based on a ceramic Nd：YAG laser operating at 1444nm. The first-stokes Raman generation at 1657nm is achieved. A maximum output power of as high as 612mW is obtained under a pump power of 20. 7 W and at a pulse repetition frequency rate of 20kHz, corresponding to an optical-to-optical conversion efficiency of 3%.

Temperature-Dependent Fluorescence Properties and Diode-Pumped Deep Red Laser Performance of Pr:LiGdF4 Crystal

We demonstrate the temperature-dependent fluorescence properties of Pr：LiGdF4 crystal tor the first time, to the best of our knowledge, and its blue diode pumped cw red laser at 720 nm at room temperature. The fluorescence lifetime and polarized emission cross sections in the visible range are measured and calculated in a temperature range from 77K to 300 K, and the variations of the fluorescence lifetime and spectra are discovered. The reasons for these changes are explained accordingly. The output wavelength of the 720nm laser is first reported on the laser performance by using a fiber-coupled laser diode at the wavelength of 442nm as the pump source, and the maximum cw output power is about 303roW.

High-Power Continuous-Wave Nd:GdVO4 Solid-State Laser Dual-End-Pumped at 880 nm

A high-power cw all-solid-state Nd：GdVO4 laser operating at 88Onto is reported. The laser consists of a low doped level Nd：GdV04 crystal dual-end-pumped by two high-power diode lasers and a compact negative confocM unstable-stable hybrid resonator. At an incident pump power of 820 W, a maximum cw output of 240 W at 1064nm is obtained. The optical-to-optical efficiency and Mope efficiency are 40.7% and 53.2%, respectively. The M2 factors in the unstable direction and in the stable direction are 4.38 and 5.44, respectively.

Direct Kerr-lens mode-locked Tm:LuYO_(3) ceramic laser

A direct Kerr-lens mode-locked Tm:LuYO_(3)ceramic laser without the aid of any mode-locked starting element is reported for the first time. A pulse duration as short as 259 fs and a maximum average output power of 326 m W are obtained at a repetition rate of 97.1 MHz. The corresponding optical spectrum centered at 2053 nm exhibits a bandwidth of 19.8 nm,which indicates the presence of nearly Fourier transform-limited pulses. Such a Kerr-lens mode-locked Tm:LuYO_(3)ceramic laser is a promising ultrashort pulse source, with both the excellent laser characteristics of Tm:LuYO3and the high-power 790 nm laser diode pumping scheme.

Quantitative analysis of C, Si, Mn, Ni, Cr and Cu in low-alloy steel under ambient conditions via laser-induced breakdown spectroscopy

A diode-pumped solid-state laser （DPSSL） with a high energetic stability and long service life is applied to ablate the steel samples instead of traditional Nd：YAG laser pumped by a xenon lamp, and several factors, such as laser pulse energy, repetition rate and argon flow rate, that influence laser-induced breakdown spectroscopy （LIBS） analytical performance are investigated in detail. Under the optimal experiment conditions, the relative standard deviations for C, Si, Mn, Ni, Cr and Cu are 3.3%-8.9%, 0.9%-2.8%, 1.2%-4.1%, 1.7%-3.0%, 1.1%-3.4% and 2.5%-8.5%, respectively, with the corresponding relative errors of 1.1%-7.9%, 1.0%-6.3%, 0.4%-3.9%, 1.5%-6.3%, 1.2%-4.0% and 1.2%-6.4%. Compared with the results of the traditional spark discharge optical emission spectrometry technique, the analytical performance of LIBS is just a little inferior due to the less stable laser-induced plasma and smaller amount of ablated sample by the laser. However, the precision, detection limits and accuracy of LIBS obtained in our present work were sufficient to meet the requirements for process analysis. These technical performances of higher stability of output energy and longer service life for DPSSL, in comparison to the Q-switch laser pumped by xeon lamp, qualify it well for the real time online analysis for different industrial applications.

High-power and high optical conversion efficiency diode-end-pumped laser with multi-segmented Nd：YAG/Nd：YVO-4

A novel flat-flat resonator consisting of two crystals（Nd：YAG ＋ Nd：YVO4） is established for power scaling in a diode-end-pumped solid-state laser. We systematically compare laser characteristics between multi-segmented（Nd：YAG ＋ Nd：YVO4） and conventional composite（Nd：YAG ＋ Nd：YAG） crystals to demonstrate the feasibility of spectral line matching for output power scale-up in end-pumped lasers. A maximum continuous-wave output power of 79.2 W is reported at 1064 nm, with Mx2= 4.82, My2= 5.48, and a pumping power of 136 W in the multi-segmented crystals（Nd：YAG ＋ Nd：YVO4）. Compared to conventional composite crystals（Nd：YAG ＋ Nd：YAG）, the optical-optical conversion efficiency of multi-segmented crystals（Nd：YAG ＋ Nd：YVO4） from 808 nm to 1064 nm is enhanced from 30% to 58.8%,while the laser output sensitivity as affected by the diode-laser temperature is reduced from 55% to 9%.

Ce:GdYAG phosphor-in-glass:An innovative yellow-emitting color converter for solid-state laser lighting

Stable,efficient and high color rendering index all-inorganic color converters are urgently demanded for white laser diodes.Phosphor-in-glass(PiG),possessing the advantages of phosphors excellent quantum efficiency as well as favorable chemical and thermal stability of glass,has attracted widespread attention.There have been only very few reports of Y_(1.31)Ce_(0.09)Gd_(1.6)Al_(5)O_(12)(Ce:GdYAG)PiG for solid-state laser light-ing.Herein,a series of Ce:GdYAG PiG samples are fabricated by a simple solid-state sintering method.Impressively,the supreme internal quantum efficiency of as-prepared PiG is 91%,which is very close to original phosphors(95%).Furthermore,PiG exhibits a high thermal conductivity(1.844 W m^(−1)K^(−1))and a maximum transparency(62%).Remarkably,by changing the concentration of phosphors and the thickness of PiG samples,a luminous efficacy of 163.5 lm/W,high color rendering index of 74.8 and low correlated color temperature of 4806.8 K are achieved under blue laser irradiation.These results indicate that the Ce:GdYAG PiG samples have shown tremendous application foreground as all-inorganic color converter for solid-state laser lighting.

33 W quasi-continuous-wave narrow-band sodium D_(2a) laser by sum-frequency generation in LBO

We demonstrate an all-solid quasi-continuous-wave （QCW） narrow-band source tunable to sodium D2a line at 589.159 nm. The source is based on sum-frequency mixing between lasers at 1064 nm and 1319 nm in a LBO crystal. The 1064 nm and 1319 nm lasers are produced from two diode side-pumped Nd：YAG master oscillator power amplifier （MOPA） laser systems, respectively. A 33 W output of 589 nm laser is obtained with beam quality factor M^2 = 1.25, frequency stability better than ±0.2 GHz and linewidth less than 0.44 GHz. A prototype 589 nm laser system is assembled, and a sodium laser guided star has been successfully observed in the field test.

1.5-MHz repetition rate passively Q-switched Nd:YVO4 laser based on WS2 saturable absorber

A transmission-type tungsten disulfide（WS_2）-based saturable absorber（SA） is fabricated and applied to passively Q-switched Nd：YVO_4 laser.The WS_2 nanosheets are deposited on a quartz substrate by the vertical evaporation method.By inserting the WS2 SA into the plano-concave laser cavity,we achieve 153-ns pulses with an average output power of1.19 W at 1064 nm.To the best of our knowledge,both of them are the best results among those obtained by the Q-switched solid-state lasers with WS_2-based absorbers.The repetition rate ranges from 1.176 MHz to 1.578 MHz.As far as we know,it is the first time that MHz level Q-switched pulses have been generated in all solid state lasers based on low-dimensional materials so far.

Judd-Oflet analysis of spectrum and laser performance of Ho:YAP crystal end-pumped by 1.91-μm Tm:YLF laser

The Ho：YAP crystal is grown by the Czochralski technique. The room-temperature polarized absorption spectra of Ho：YAP crystal was measured on a c-cut sample with 1 at% holmium. According to the obtained Judd-Ofelt intensity parameters Ω2 = 1.42 × 10^-20cm^2, Ω4 = 2.92 ×10^-20 cm^2, and Ω6 =1.71 ×10^-20cm^2, this paper calculated the fluorescence lifetime to be 6 ms for ^5I7→^5Is transition, and the integrated emission cross section to be 2.24 × 10^-18 cm^2. It investigates the room-temperature Ho：YAP laser end-pumped by a 1.91-μm Tm：YLF laser. The maximum output power was 4.1 W when the incident 1.91-μm pump power was 14.4W. The slope efficiency is 40.8%, corresponding to an optical-to-optical conversion efficiency of 28.4%. The Ho：YAP output wavelength was centred at 2118 nm with full width at half maximum of about 0.8nm.

Passively mode-locked Nd：GdVO4 laser at 912nm

This paper demonstrates the passively mode-locked Nd：GdVO4 laser operating on the ^4F3/2-^4I9/2 transition at 912 nm by using a semiconductor saturable-absorber mirror for passive mode locking, stable continuous wave modelocked 912nm laser was achieved with a repetition rate of 176 MHz. At the incident pump power of 17.7W, 22.6mW average output power of stable mode-locked laser was obtained with a slope efficiency of 0.3%.

MXene Ti_3C_2T_x saturable absorber for pulsed laser at 1.3 μm

The excellent optical properties of MXene provide new opportunities for short-pulse lasers. A diode-pumped passively Q-switched laser at 1.3 μm wavelength with MXene Ti3C2Tx as saturable absorber was achieved for the first time. The stable passively Q-switched laser has 454 ns pulse width and 162 kHz repetition rate at 4.5 W incident pumped power. The experimental results show that the MXene Ti3C2Tx saturable absorber can be used as an optical modulator to generate short pulse lasers in a solid-state laser field.

Tunable second harmonic generation from a Kerr-lens mode-locked Yb:YCa4O(BO3)3 femtosecond laser

We experimentally demonstrated a diode-pumped Kerr-lens mode-locked femtosecond（fs） laser with a self-frequency doubling Yb：YCa_4O（BO_3）_3 crystal.Sub-40 fs laser pulses were directly generated from the oscillator without extracavity compression.The central wavelength was tunable from 1039 nm to 1049 nm with a typical bandwidth of 35 nm and an average output power of 53 mW.For the first time,a self-frequency doubled second harmonic green laser with tunable range from 519 nm to 525 nm was observed.