Directional solidification experiments on Pb-Bi peritectic alloys were carried out at very low growth rate （v=0.5 μm/s） and high temperature gradient （G=35 K/mm） in an improved Bridgman furnace. The banding struc...Directional solidification experiments on Pb-Bi peritectic alloys were carried out at very low growth rate （v=0.5 μm/s） and high temperature gradient （G=35 K/mm） in an improved Bridgman furnace. The banding structures were observed in both hypoperitectic and hyperperitectic compositions （Pb-xBi, x=26%, 28%, 30% and 34%）. Tree-like primary α phase in the center of the sample surrounded by the peritectic β phase matrix was also observed, resulting from the melt convection. The banding microstructure, however, is found to be transient after the tree-like structure and only the peritectic phase forms after a few bands. Composition variations in the banding structure are measured to determine the nucleation undercooling for both α and β phases. In a finite length sample, convection is shown to lead only to the transient formation of bands. In this transient banding regime, only a few bands with a variable width are formed, and this transient banding process can occur over a wide range of compositions inside the two-phase peritectic region.展开更多
The effects of pulling velocity on the solidification behavior and microstructural parameters of A1Sil0Mg alloys prepared in a Bridgman-type directional solidification furnace were investigated. The microstructure, pa...The effects of pulling velocity on the solidification behavior and microstructural parameters of A1Sil0Mg alloys prepared in a Bridgman-type directional solidification furnace were investigated. The microstructure, particularly the secondary dendritic arm spacing （SDAS）, and the Brinell hardness （BH） of the solidified A1Sil0Mg alloys were characterized for samples with cylindrical shapes and differ- ent conicities （θ = 0°, 5°, and 10°）. Microstructural studies revealed an increased density of ct-A1 phase dendrites and a decreased interden- dritic distance with increasing pulling velocity. The dendrites were found to be preferentially oriented along the pulling direction for low pulling velocities. For larger pulling velocities, the dendrites grew first in the cooling direction but then broke as others nucleated and coars- ened. The HB values of the solidified samples increased as the pulling velocity increased. In regard to sample conicity, smaller dendrites were observed for an apex angle of θ = 5°, resulting in the largest HB value. This result was interpreted in terms of the favorable orientation of the dendrite along the pulling direction.展开更多
Accelerated crucible rotation technique(ACRT) has been used for the directional solidification of Al-4.5wt% Cu binary alloy.By rotating the crucible at varying rate and direction,forced liquid flows are aroused These ...Accelerated crucible rotation technique(ACRT) has been used for the directional solidification of Al-4.5wt% Cu binary alloy.By rotating the crucible at varying rate and direction,forced liquid flows are aroused These flows include Ekman flow,Couette flow and Spiral Shear flow.Especially,Ekman flow acts directly at the L/S interface,changes diffusion and heat exchange conditions and has strong influences on the morphology of L/S interface.Experimental results show that,compared with normal Bridgman specimens,the solidification region is much narrower and the cell spacing is much smaller in ACRT specimens.These influences become much stronger when the accelerating rate is increased.展开更多
基金Project (20110491492) supported by the China Postdoctoral Science FoundationProject (20114BAB216017) supported by the Natural Science Foundation of Jiangxi Province, ChinaProject (GJJ12035) supported by the Science Foundation of the Educational Department of Jiangxi Province, China
文摘Directional solidification experiments on Pb-Bi peritectic alloys were carried out at very low growth rate （v=0.5 μm/s） and high temperature gradient （G=35 K/mm） in an improved Bridgman furnace. The banding structures were observed in both hypoperitectic and hyperperitectic compositions （Pb-xBi, x=26%, 28%, 30% and 34%）. Tree-like primary α phase in the center of the sample surrounded by the peritectic β phase matrix was also observed, resulting from the melt convection. The banding microstructure, however, is found to be transient after the tree-like structure and only the peritectic phase forms after a few bands. Composition variations in the banding structure are measured to determine the nucleation undercooling for both α and β phases. In a finite length sample, convection is shown to lead only to the transient formation of bands. In this transient banding regime, only a few bands with a variable width are formed, and this transient banding process can occur over a wide range of compositions inside the two-phase peritectic region.
基金financially supported by the doctoral scholarship grant of the Algerian-MHESR
文摘The effects of pulling velocity on the solidification behavior and microstructural parameters of A1Sil0Mg alloys prepared in a Bridgman-type directional solidification furnace were investigated. The microstructure, particularly the secondary dendritic arm spacing （SDAS）, and the Brinell hardness （BH） of the solidified A1Sil0Mg alloys were characterized for samples with cylindrical shapes and differ- ent conicities （θ = 0°, 5°, and 10°）. Microstructural studies revealed an increased density of ct-A1 phase dendrites and a decreased interden- dritic distance with increasing pulling velocity. The dendrites were found to be preferentially oriented along the pulling direction for low pulling velocities. For larger pulling velocities, the dendrites grew first in the cooling direction but then broke as others nucleated and coars- ened. The HB values of the solidified samples increased as the pulling velocity increased. In regard to sample conicity, smaller dendrites were observed for an apex angle of θ = 5°, resulting in the largest HB value. This result was interpreted in terms of the favorable orientation of the dendrite along the pulling direction.
文摘Accelerated crucible rotation technique(ACRT) has been used for the directional solidification of Al-4.5wt% Cu binary alloy.By rotating the crucible at varying rate and direction,forced liquid flows are aroused These flows include Ekman flow,Couette flow and Spiral Shear flow.Especially,Ekman flow acts directly at the L/S interface,changes diffusion and heat exchange conditions and has strong influences on the morphology of L/S interface.Experimental results show that,compared with normal Bridgman specimens,the solidification region is much narrower and the cell spacing is much smaller in ACRT specimens.These influences become much stronger when the accelerating rate is increased.
