A three-dimensional conjugate tooth surface design method for Harmonic Drive with a double-circular-arc tooth profle is proposed. The radial deformation function of the fexspline (FS), obtained through Finite Element ...A three-dimensional conjugate tooth surface design method for Harmonic Drive with a double-circular-arc tooth profle is proposed. The radial deformation function of the fexspline (FS), obtained through Finite Element (FE) analysis, is incorporated into the kinematics model. By analyzing the FS tooth enveloping process, the optimization of the overlapping conjugate tooth profle is achieved. By utilizing the hobbing process, the three-dimensional machinable tooth surface of FS can be acquired. Utilizing the coning deformation of the FS, simulations are conducted to analyze the multi-section assembly and meshing motion of the machinable tooth surface. The FE method is utilized to analyze and compare the loaded contact characteristics. Results demonstrate that the proposed design method can achieve an internal gear pair consisting of a circular spline with a spur gear tooth surface and the FS with a machinable tooth surface. With the rated torque, approximately 24% of the FS teeth are engaged in meshing, and more than 4/5 of the tooth surface in the axial direction carries the load. The contact patterns, maximum contact pressure, and transmission error of the machinable tooth surface are 227.2%, 40.67%, and 71.24% of those on the spur gear tooth surface, respectively. It clearly demonstrates exceptional transmission performance.展开更多
A small hole of 0.9mm in diameter is drilled at the theoretical contact point of the convex tooth flank of the measured gear, and the hole leads throughout to the non-working flank. A stylus glued to the core of trans...A small hole of 0.9mm in diameter is drilled at the theoretical contact point of the convex tooth flank of the measured gear, and the hole leads throughout to the non-working flank. A stylus glued to the core of transformer is put into the hole, and the stylus can freely contact with the meshed concave tooth flank. The transformer is installed on the body of gear to be measured. Rotate the positioning worm slowly after loading, and locate the contact point at the hole of convex tooth flank, the displacement value measured is considered as the deformation of convex tooth. The deformations at the middle and the two ends of tooth breadth for the helical gears with double-circular-cra tooth profile whose modules are 3mm and 4mm respectively are measured in the paper.展开更多
基金Supported by Guangdong Provincial Key-Area Research and Development Program(Grant No.2019B090917002).
文摘A three-dimensional conjugate tooth surface design method for Harmonic Drive with a double-circular-arc tooth profle is proposed. The radial deformation function of the fexspline (FS), obtained through Finite Element (FE) analysis, is incorporated into the kinematics model. By analyzing the FS tooth enveloping process, the optimization of the overlapping conjugate tooth profle is achieved. By utilizing the hobbing process, the three-dimensional machinable tooth surface of FS can be acquired. Utilizing the coning deformation of the FS, simulations are conducted to analyze the multi-section assembly and meshing motion of the machinable tooth surface. The FE method is utilized to analyze and compare the loaded contact characteristics. Results demonstrate that the proposed design method can achieve an internal gear pair consisting of a circular spline with a spur gear tooth surface and the FS with a machinable tooth surface. With the rated torque, approximately 24% of the FS teeth are engaged in meshing, and more than 4/5 of the tooth surface in the axial direction carries the load. The contact patterns, maximum contact pressure, and transmission error of the machinable tooth surface are 227.2%, 40.67%, and 71.24% of those on the spur gear tooth surface, respectively. It clearly demonstrates exceptional transmission performance.
文摘A small hole of 0.9mm in diameter is drilled at the theoretical contact point of the convex tooth flank of the measured gear, and the hole leads throughout to the non-working flank. A stylus glued to the core of transformer is put into the hole, and the stylus can freely contact with the meshed concave tooth flank. The transformer is installed on the body of gear to be measured. Rotate the positioning worm slowly after loading, and locate the contact point at the hole of convex tooth flank, the displacement value measured is considered as the deformation of convex tooth. The deformations at the middle and the two ends of tooth breadth for the helical gears with double-circular-cra tooth profile whose modules are 3mm and 4mm respectively are measured in the paper.
