Numerical Study on Reduction in Aerodynamic Drag and Noise of High-Speed Pantograph

Reducing the aerodynamic drag and noise levels of high-speed pantographs is important for promoting environmentally friendly,energy efficient and rapid advances in train technology.Using computational fluid dynamics theory and the K-FWH acoustic equation,a numerical simulation is conducted to investigate the aerodynamic characteristics of high-speed pantographs.A component optimization method is proposed as a possible solution to the problemof aerodynamic drag and noise in high-speed pantographs.The results of the study indicate that the panhead,base and insulator are the main contributors to aerodynamic drag and noise in high-speed pantographs.Therefore,a gradual optimization process is implemented to improve the most significant components that cause aerodynamic drag and noise.By optimizing the cross-sectional shape of the strips and insulators,the drag and noise caused by airflow separation and vortex shedding can be reduced.The aerodynamic drag of insulator with circular cross section and strips with rectangular cross section is the largest.Ellipsifying insulators and optimizing the chamfer angle and height of the windward surface of the strips can improve the aerodynamic performance of the pantograph.In addition,the streamlined fairing attached to the base can eliminate the complex flow and shield the radiated noise.In contrast to the original pantograph design,the improved pantograph shows a 21.1%reduction in aerodynamic drag and a 1.65 dBA reduction in aerodynamic noise.

Preparation and performance evaluation of the slickwater using novel polymeric drag reducing agent with high temperature and shear resistance ability

Slickwater fracturing fluids are widely used in the development of unconventional oil and gas resources due to the advantages of low cost,low formation damage and high drag reduction performance.However,their performance is severely affected at high temperatures.Drag reducing agent is the key to determine the drag reducing performance of slickwater.In this work,in order to further improve the temperature resistance of slickwater,a temperature-resistant polymeric drag reducing agent(PDRA)was synthesized and used as the basis for preparing the temperature-resistant slickwater.The slickwater system was prepared with the compositions of 0.2 wt%PDRA,0.05 wt%drainage aid nonylphenol polyoxyethylene ether phosphate(NPEP)and 0.5 wt%anti-expansion agent polyepichlorohydrindimethylamine(PDM).The drag reduction ability,rheology properties,temperature and shear resistance ability,and core damage property of slickwater were systematically studied and evaluated.In contrast to on-site drag reducing agent(DRA)and HPAM,the temperature-resistant slickwater demonstrates enhanced drag reduction efficacy at 90℃,exhibiting superior temperature and shear resistance ability.Notably,the drag reduction retention rate for the slickwater achieved an impressive 90.52%after a 30-min shearing period.Additionally,the core damage is only 5.53%.We expect that this study can broaden the application of slickwater in high-temperature reservoirs and provide a theoretical basis for field applications.

Airfoil friction drag reduction based on grid-type and super-dense array plasma actuators

To improve the cruise flight performance of aircraft, two new configurations of plasma actuators(grid-type and super-dense array) were investigated to reduce the turbulent skin friction drag of a low-speed airfoil. The induced jet characteristics of the two actuators in quiescent air were diagnosed with high-speed particle image velocimetry(PIV), and their drag reduction efficiencies were examined under different operating conditions in a wind tunnel. The results showed that the grid-type plasma actuator was capable of producing a wall-normal jet array(peak magnitude: 1.07 m/s) similar to that generated in a micro-blowing technique, while the superdense array plasma actuator created a wavy wall-parallel jet(magnitude: 0.94 m/s) due to the discrete spanwise electrostatic forces. Under a comparable electrical power consumption level,the super-dense array plasma actuator array significantly outperformed the grid-type configuration,reducing the total airfoil friction drag by approximately 22% at a free-stream velocity of 20 m/s.The magnitude of drag reduction was proportional to the dimensionless jet velocity ratio(r), and a threshold r = 0.014 existed under which little impact on airfoil drag could be discerned.

Numerical Study on the Effect of Vortex Generators on the Aerodynamic Drag of a High-Speed Train

A relatively high aerodynamic drag is an important factor that hinders the further acceleration of high-speed trains.Using the shear stress transport(SST)k-ωturbulence model,the effect of various vortex generator types on the aerodynamic characteristics of an ICE2(Inter-city Electricity)train has been investigated.The results indi-cate that the vortex generators with wider triangle,trapezoid,and micro-ramp arranged on the surface of the tail car can significantly change the distribution of surface pressure and affect the vorticity intensity in the wake.This alteration effectively reduces the resistance of the tail car.Meanwhile,the micro-ramp vortex generator with its convergent structure at the rear exhibits enhancedflow-guiding capabilities,resulting in a 15.4%reduction in the drag of the tail car.

Estimation of Displacement and Extension due to Reverse Drag of Normal Faults: Forward Method

In the case of reverse drag of normal faulting, the displacement and horizontal extension are determined based on the established equations for the three mechanisms: rigid body, vertical shear and inclined shear. There are three sub-cases of basal detachment for the rigid body model: horizontal detachment, antithetic detachment and synthetic detachment. For the rigid body model, the established equations indicate that the total displacement on the synthetic base (Dt2) is the largest, that on the horizontal base (Dt1) is moderate, and that on the antithetic base (Dt3) is the smallest. On the other hand, the value of (Dt1) is larger than the displacement for the vertical shear (Dt4). The value of (Dt1) is larger than or less than the displacement for the inclined shear (Dt5) depending on the original fault dip δ0, bedding angle θ, and the angle of shear direction β. For all original parameters, the value of Dt5 is less than the value of Dt4. Also, by comparing three rotation mechanisms, we find that the inclined shear produces largest extension, the rigid body model with horizontal detachment produces the smallest extension, and the vertical shear model produces moderate extension.

Parametric Optimization of Wheel Spoke Structure for Drag Reduction of an Ahmed Body

The wheels have a considerable influence on the aerodynamic properties and can contribute up to 25%of the total drag on modern vehicles.In this study,the effect of the wheel spoke structure on the aerodynamic performance of the isolated wheel is investigated.Subsequently,the 35°Ahmed body with an optimized spoke structure is used to analyze the flow behavior and the mechanism of drag reduction.The Fluent software is employed for this investigation,with an inlet velocity of 40 m/s.The accuracy of the numerical study is validated by comparing it with experimental results obtained from the classical Ahmed model.To gain a clearer understanding of the effects of the wheel spoke parameters on the aerodynamics of both the wheel and Ahmedmodel,and five design variables are proposed:the fillet angleα,the inside arc radius R1,the outside radius R2,and the same length of the chord L1 and L2.These variables characterize the wheel spoke structure.The Optimal Latin Hypercube designmethod is utilized to conduct the experimental design.Based on the simulation results of various wheel spoke designs,the Kriging model and the adaptive simulated annealing algorithm is selected to optimize the design parameters.The objective is to achieve the best combination for maximum drag reduction.It is indicated that the optimized spoke structure resulted in amaximum drag reduction of 5.7%and 4.7%for the drag coefficient of the isolated wheel and Ahmed body,respectively.The drag reduction is primarily attributed to changes in the flow state around the wheel,which suppressed separation bubbles.Additionally,it influenced the boundary layer thickness around the car body and reduced the turbulent kinetic energy in the wake flow.These effects collectively contributed to the observed drag reduction.

Effects of Crosswise Appendage Plate Flexibility on the Drag Reduction Characteristics of Cylinder

In engineering applications (Like an ocean riser), fluid flow around bluff bodies generates substantial resistance, which can jeopardize structural integrity, lifespan, and escalate resource consumption. Therefore, employing drag reduction measures becomes particularly crucial. This paper employs the immersed boundary method to investigate the impact of transversely oriented appendage plate flexibility on the drag of cylinders under different Reynolds numbers and distances. The results indicate that flexible appendage plate exerts drag reduction effects on the downstream cylinder, with this effect gradually diminishing as Reynolds numbers increase. At identical Reynolds numbers, the drag reduction effect initially increases and then decreases with distance, with the optimal drag reduction distance observed at D = 2.5. Compared to cylinders without appendage plate, the maximum drag reduction achieved is 30.551%. Addressing the drag reduction issue in cylinders holds significant importance for ensuring engineering structural integrity, enhancing engineering efficiency, and developing novel underwater towing systems.

Synthesis and Performance of an Associative Anti-shear Drag Reducer Based on Hydrogen Bond Association of Dodecyl Methacrylate

Using K2S2O8-Na2SO3 as the redox initiation system,a hydrogen-bond-association-based dodecyl methacrylate system associative anti-shear drag reducer was synthesised by standard emulsion polymerisation.The reaction process was simple and gentle as well as safe and stable.Molecular design was carried out using molecular dynamics simulation methods.The results of infrared spectroscopy,thermogravimetric analysis,differential scanning calorimetry,gel chromatography,and laser light scattering showed that the reaction polymerisation was relatively complete,the product was uniform,the molecular weight distribution was controllable,and the synthesised polymer had good flexibility.The donor lauryl methacrylate-styrene-methacrylic acid(LMA-St-MAA)and acceptor lauryl methacrylate-styrene-dimethylaminoethyl methacrylate(LMA-St-DMA)polymers had an associative intermolecular interaction force,which increased the molecular cluster size of the associative system complex.The complex had good shear resistance,and the test results of the tube pump shear test showed that the synthesised associative oil-soluble polymer drag reduction system exhibited better drag reduction rate performance than poly-α-olefins over repeated cycles.The research results provide a reference plan for minimising the number of station-to-station inputs,thereby ensuring the stability of oil pipelines and reducing transportation costs.

Drag Coefficient of a Non-Convex Polygonal Plate during Free Fall

Waterside creatures or aquatic organisms use a fin or web to generate a thrust force. These fins or webs have a non-convex section, referred to as a non-convex shape. We investigate the drag force acting on a non-convex plate during unsteady motion. We perform the experiment in a water tank during free fall. We fabricate the non-convex plate by cutting isosceles triangles from the side of a convex hexagonal plate. The base angle of the triangle is between 0° to 45°. The base angle is 0 indicates the convex hexagonal thin plate. We estimate the drag coefficient with the force balance acting on the model based on the image analysis technique. The results indicate that increasing the base angle by more than 30° increased the drag coefficient. The drag coefficient during unsteady motion changed with the growth of the vortex behind the model. The vortex has small vortices in the shear layer, which is related to the Kelvin-Helmholtz instabilities.

Comparative analysis on gas–solid drag models in MFIX-DEM simulations of bubbling fluidized bed

In this study,the open-source software MFIX-DEM simulations of a bubbling fluidized bed(BFB)are applied to assess nine drag models according to experimental and direct numerical simulation(DNS)results.The influence of superficial gas velocity on gas–solid flow is also examined.The results show that according to the distribution of time-averaged particle axial velocity in y direction,except for Wen–Yu and Tenneti–Garg–Subramaniam(TGS),other drag models are consistent with the experimental and DNS results.For the TGS drag model,the layer-by-layer movement of particles is observed,which indicates the particle velocity is not correctly predicted.The time domain and frequency domain analysis results of pressure drop of each drag model are similar.It is recommended to use the drag model derived from DNS or fine grid computational fluid dynamics–discrete element method(CFD-DEM)data first for CFD-DEM simulations.For the investigated BFB,the superficial gas velocity less than 0.9 m·s^(-1) should be adopted to obtain normal hydrodynamics.

The Influence of Sea Sprays on Drag Coefficient at High Wind Speed

Field and laboratory observations indicate that the variation of drag coefficient with wind speed at high winds is different from that under low-to-moderate winds.By taking the effects of wave development and sea spray into account,a new parameterization of drag coefficient applicable from low to extreme winds is proposed.It is shown that,under low-to-moderate wind conditions so that the sea spray effects could be neglected,the nondimensional aerodynamic roughness first increases and then decreases with the increasing wave age;whereas under high wind conditions,the drag coefficient decreases with the increasing wind speed due to the modification of the logarithmic wind profile by the effect of sea spray droplets produced by bursting bubbles or wind tearing breaking wave crests.The drag coefficients and sea surface aerodynamic roughnesses reach their maximum values vary under different wave developments.Correspondingly,the reduction of drag coefficient under high winds reduces the increasing rate of friction velocity with increasing wind speed.

Experimental and Numerical Analysis of Oil-Water Flow with Drag Reducing Polymers in Horizontal Pipes

The well-known frictional effect related to liquid-liquid two-phaseflow in pipelines can be reduced using drag-reducing additives.In this study,such an effect has been investigated experimentally using a mixture of oil and water.Moreover,numerical simulations have been carried out using the COMSOL simulation software.The mea-surements were taken in a horizontal pipe with the length and diameter equal to 3 and 0.125 m,respectively.Moreover,Polyethylene oxide with 150 ppm was exploited to reduce the drag effect while considering different water-to-oil fractions(0.3,0.4,0.5,and 0.7)and a constant totalflow velocity of 2.3 m/s.As made evident by the results,a significant reduction can be obtained in terms of pressure drop,which becomes even more significant as the water to oil fraction is increased.The maximum achieved drag reduction is 70%with a water fraction of 0.7.The results also show that the addition of polymer additives can also have an impact on theflow pattern.Com-parison of experimental and numerically determined pressure drop indicates that the error is smaller than 7%.

Aerodynamic shape and drag scaling law of a flexible fibre in a flowing medium

The study of a flexible body immersed in a flowing medium is one of the best way to find its aerodynamic shape.This Letter revisited the problem that was first studied by Alben et al.(Nature 420,479–481,2002).To determine the aerodynamic shape of the fibre,a simpler approach is proposed.A universal drag scaling law is obtained and the universality of the Alben-Shelley-Zhang scaling law is confirmed by using dimensional analysis.A complete Maple code is provided for finding aerodynamic shape of the fibre in the flowing medium.

Computational Solution to the Problems of Projectile Motion under Significant Linear Drag Effect

This paper investigates the computational solution to the problem of projectile motion under a significant linear drag effect. The drag force acting on the particle within the medium of propagation is proportional to the cross-section area of the projectile, the velocity of the particle, and the medium’s density. From zero air resistance force (vacuum) the problems are well known with solutions, but with air resistance (drag force) the problems have no exact analytical solutions which lead to most of the significant scientific research works using numerical methods. Therefore, this study aims to present the analysis of the computational modelling of drag force exerted by the surrounding medium on the linear motion. However, the horizontal and vertical components of differential equations of motion were derived and characterized from the solutions governed by Newton’s 2nd law of motion. The baseball features were presented as the projectile (object) in this work. In addition, the numerical computational results were received from FreeMat. The results were discussed and compared with those from the vacuum. Moreover, the displacements, velocities, range, and trajectories of the projectile were all discussed and a conclusion was made.

Preparation of Poly-α-Olefin Microcapsule Particles Coated with Polyurethane as a Drag Reducer Based on Interface Polymerization

The molecular behavior of polyurethane(PU)coating materials during the surface adsorption of poly-α-olefin as a drag reducing polymer was explored by a molecular dynamics simulation.Three different PU capsule wall materials were synthesized using two reaction monomers,and a poly-α-olefin/PU drag reducer microcapsule was prepared based on interface polymerization.The structure,morphology,thermal stability,compressive strength,and drag reduction performance of the microcapsules were characterized and compared.The results showed that a non-bonding interaction induced the adsorption of the PU coating material,poly-α-olefin and PU then fused at the interface,and the PU coating material was embedded into the inner grooves of poly-α-olefin in the form of a local mosaic,thereby forming a stable core–shell structure.The morphological characterization indicated that PU and poly-α-olefin could form microcapsule structures.The thermal decomposition temperature of the microcapsule was dependent on the type of capsule wall material.The microcapsule structure had a slight effect on poly-α-olefin drag reduction.The system enabled poly-α-olefin to exist in powdered particles through microcapsulation,and had a good dispersion effect that facilitated storage and transport processes.The method effectively inhibited the accumulation and bonding of poly-α-olefin at room temperature.

Nanoparticle-induced drag reduction for polyacrylamide in turbulent flow with high Reynolds numbers

Although having been increasingly studied, there is still controversy as to when the addition of nanoparticles could improve the drag reduction performance of polymer drag reducer and particularly what is the underlying mechanism from the fluid dynamics viewpoint. The drag reduction effects of adding SiO_(2) nanoparticles to various polymer polyacrylamide(PAM) solutions were examined in this work.The optimal combination of SiO_(2) nanoparticles with cationic polyacrylamide was confirmed.Interestingly,the addition of SiO_(2) nanoparticles to cationic polyacrylamide solution was shown to be quite efficient for reducing drag, but only at higher flow rates with Reynolds numbers more than 6000, below which the nanoparticle addition is even negative. The addition of SiO_(2) nanoparticles to the PAM solution is supposed to play a dual role. The first is an increase in flow resistance caused by the Brownian motion of nanoparticles, while the second is a decrease in flow resistance caused by acting as nodes to protect the polymer chain from shear-induced breaking under high shear action. At optimal nanoparticle concentration and under higher Reynolds numbers, the later effect is dominant, which could improve the drag reduction performance of polymer drag reducers. Our work should serve as a guide for the application of natural gas fracturing, where the flow rate is frequently very high.

Solute drag-controlled grain growth in magnesium investigated by quasi in-situ orientation mapping and level-set simulations

Critical properties of metallic materials,such as the yield stress,corrosion resistance and ductility depend on the microstructure and its grain size and size distribution.Solute atoms that favorably segregate to grain boundaries produce a pinning atmosphere that exerts a drag pressure on the boundary motion,which strongly affects the grain growth behavior during annealing.In the current work,the characteristics of grain growth in an annealed Mg-1 wt.%Mn-1 wt.%Nd magnesium alloy were investigated by advanced experimental and modeling techniques.Systematic quasi in-situ orientation mappings with a scanning electron microscope were performed to track the evolution of local and global microstructural characteristics as a function of annealing time.Solute segregation at targeted grain boundaries was measured using three-dimensional atom probe tomography.Level-set computer simulations were carried with different setups of driving forces to explore their contribution to the microstructure development with and without solute drag.The results showed that the favorable growth advantage for some grains leading to a transient stage of abnormal grain growth is controlled by several drivers with varying importance at different stages of annealing.For longer annealing times,residual dislocation density gradients between large and smaller grains are no longer important,which leads to microstructure stability due to predominant solute drag.Local fluctuations in residual dislocation energy and solute concentration near grain boundaries cause different boundary segments to migrate at different rates,which affects the average growth rate of large grains and their evolved shape.

井地过渡带对聚合物驱油剂性能影响研究

利用井地过渡带剪切模拟实验装置,以疏水缔合聚合物AP-P4为研究对象,研究不同吸水强度条件下,剪切后聚合物溶液的表观黏度、流变性、阻力和残余阻力系数、微观结构以及水动力学半径的变化情况。结果表明,经井地过渡带剪切后,随着吸水强度的增大,聚合物AP-P4溶液的黏度损失率高达61.4%,建立阻力系数和残余阻力系数的能力降低40.0%以上,但其建立残余阻力系数能力的降低幅度要比建立阻力系数能力的降低幅度小。聚合物溶液的储能模量和损耗模量降低,微观结构被破坏的越严重,水动力学半径越小。

不同形状的珊瑚砂颗粒沉降试验研究

珊瑚砂在液体中的沉速是反映泥沙运动特性的一个重要物理量。由于珊瑚砂形状多样,套用现有的珊瑚砂沉速公式进行计算并不合适。针对珊瑚砂颗粒开展形状分析,将珊瑚砂颗粒分成枝棒状、片状和块状3种形状,然后开展单颗粒沉降试验。基于试验数据,分析不同形状珊瑚砂颗粒的沉降特性,与各家理论公式计算结果进行比较分析,选取经典的珊瑚砂颗粒沉速公式,引入颗粒形状系数进行公式修正,从而推求了枝棒状、片状和块状珊瑚砂颗粒的阻力系数和沉降速度公式。该公式充分考虑不规则珊瑚砂颗粒形状的影响,具有更高的计算精度和适用性。

某SUV气动减阻优化及其流场机制

为了提高整车燃油经济性,本文以某款SUV车型为研究对象,将仿真与试验相结合改善汽车行驶过程中的气动阻力系数。首先通过风洞试验确定对整车气动阻力有重要影响的区域或部件,其次对气动阻力系数贡献值较大的部件或区域进行减阻优化。结果表明,前轮阻风板、尾灯和尾翼对整车气动阻力系数贡献值较大。对前轮阻风板的改型,有效降低正压区面积以及减弱车轮干扰阻力;对尾灯和尾翼的优化设计,改善了尾部负压区,缩短了分离流在后窗上部的再附着的距离。基于本征正交分解方法进行局部流场信息的提取和分析可知,1阶与2阶模态主要构成了该SUV尾流场的关键流态。经试验与仿真验证,相比于初始方案,气动优化组合设计减阻率可达7.5%。本文为新一代SUV改型与升级换代提供了理论基础与技术支持。