The fundamental principle of road identification by using angular acceleration of driving wheels was demonstrated in this paper. Based on the analysis of energy conversion and parameters variation during the vehicle d...The fundamental principle of road identification by using angular acceleration of driving wheels was demonstrated in this paper. Based on the analysis of energy conversion and parameters variation during the vehicle drive slip process, the change of adhesion coefficient relative to the an- gular acceleration were theoretically studied experimentally validated. The variation shows that the change of adhesion coefficient relative to the angular acceleration and the change of slip ratio in the drive slip process have same trend-both of them exist an only optimal angular acceleration corre- sponding to the peak value of adhesion coefficient. The peak adhesion coefficient of the prototype vehicle is about 0. 14 on the ice-covered road surfaces, with the corresponding optimal angular accel- eration of about 23.5 rad/s2 and optimal slip ratio of about 9. 4%.展开更多
The independent driving wheel system, which is composed of in-wheel permanent magnet synchronous motor（I-PMSM） and tire, is more convenient to estimate the slip ratio because the rotary speed of the rotor can be acc...The independent driving wheel system, which is composed of in-wheel permanent magnet synchronous motor（I-PMSM） and tire, is more convenient to estimate the slip ratio because the rotary speed of the rotor can be accurately measured. However, the ring speed of the tire ring doesn’t equal to the rotor speed considering the tire deformation. For this reason, a deformable tire and a detailed I-PMSM are modeled by using Matlab/Simulink. Moreover, the tire/road contact interface（a slippery road） is accurately described by the non-linear relaxation length-based model and the Magic Formula pragmatic model. Based on the relatively accurate model, the error of slip ratio estimated by the rotor rotary speed is analyzed in both time and frequency domains when a quarter car is started by the I-PMSM with a definite target torque input curve. In addition, the natural frequencies（NFs） of the driving wheel system with variable parameters are illustrated to present the relationship between the slip ratio estimation error and the NF. According to this relationship, a low-pass filter, whose cut-off frequency corresponds to the NF, is proposed to eliminate the error in the estimated slip ratio. The analysis, concerning the effect of the driving wheel parameters and road conditions on slip ratio estimation, shows that the peak estimation error can be reduced up to 75% when the LPF is adopted. The robustness and effectiveness of the LPF are therefore validated. This paper builds up the deformable tire model and the detailed I-PMSM models, and analyzes the effect of the driving wheel parameters and road conditions on slip ratio estimation.展开更多
Three major methods currently in the use of determining vehicle speed based on wheel speeds, the minimum wheel speed, minimum wheel speed corrected by slope method and the Kalman filter method, are analyzed, with meri...Three major methods currently in the use of determining vehicle speed based on wheel speeds, the minimum wheel speed, minimum wheel speed corrected by slope method and the Kalman filter method, are analyzed, with merits and defects of each approach stated. Through simulations, the Kalman filter method based on minimum wheel speed shows improved accuracy, in addition to better adaptivity to vehicle reference speed. It also can be used to acceleration ship regulation （ASR） in part-time four-wheel drive vehicles.展开更多
建立了四轮驱动汽车加速过程的数学模型,以滑转率为调节对象,提出一种基于模糊P ID控制的驱动防滑控制A SR算法。设计了以发动机油门为控制对象的模糊-P ID控制器并讨论了控制器切换参数的选取,并针对均一低附着路面以及分离路面在S im ...建立了四轮驱动汽车加速过程的数学模型,以滑转率为调节对象,提出一种基于模糊P ID控制的驱动防滑控制A SR算法。设计了以发动机油门为控制对象的模糊-P ID控制器并讨论了控制器切换参数的选取,并针对均一低附着路面以及分离路面在S im u link仿真环境下进行了动态仿真。对比仿真结果,表明模糊P ID控制性能优于单一的模糊控制。展开更多
基金Supported by the National"Eleventh Five"Project of China(40401040302)
文摘The fundamental principle of road identification by using angular acceleration of driving wheels was demonstrated in this paper. Based on the analysis of energy conversion and parameters variation during the vehicle drive slip process, the change of adhesion coefficient relative to the an- gular acceleration were theoretically studied experimentally validated. The variation shows that the change of adhesion coefficient relative to the angular acceleration and the change of slip ratio in the drive slip process have same trend-both of them exist an only optimal angular acceleration corre- sponding to the peak value of adhesion coefficient. The peak adhesion coefficient of the prototype vehicle is about 0. 14 on the ice-covered road surfaces, with the corresponding optimal angular accel- eration of about 23.5 rad/s2 and optimal slip ratio of about 9. 4%.
基金Supported by National Natural Science Foundation of China (Grant Nos.51275264,51275265)National Hi-tech Research and Development Program of China (Grant No.2012DFA81190)
文摘The independent driving wheel system, which is composed of in-wheel permanent magnet synchronous motor（I-PMSM） and tire, is more convenient to estimate the slip ratio because the rotary speed of the rotor can be accurately measured. However, the ring speed of the tire ring doesn’t equal to the rotor speed considering the tire deformation. For this reason, a deformable tire and a detailed I-PMSM are modeled by using Matlab/Simulink. Moreover, the tire/road contact interface（a slippery road） is accurately described by the non-linear relaxation length-based model and the Magic Formula pragmatic model. Based on the relatively accurate model, the error of slip ratio estimated by the rotor rotary speed is analyzed in both time and frequency domains when a quarter car is started by the I-PMSM with a definite target torque input curve. In addition, the natural frequencies（NFs） of the driving wheel system with variable parameters are illustrated to present the relationship between the slip ratio estimation error and the NF. According to this relationship, a low-pass filter, whose cut-off frequency corresponds to the NF, is proposed to eliminate the error in the estimated slip ratio. The analysis, concerning the effect of the driving wheel parameters and road conditions on slip ratio estimation, shows that the peak estimation error can be reduced up to 75% when the LPF is adopted. The robustness and effectiveness of the LPF are therefore validated. This paper builds up the deformable tire model and the detailed I-PMSM models, and analyzes the effect of the driving wheel parameters and road conditions on slip ratio estimation.
文摘Three major methods currently in the use of determining vehicle speed based on wheel speeds, the minimum wheel speed, minimum wheel speed corrected by slope method and the Kalman filter method, are analyzed, with merits and defects of each approach stated. Through simulations, the Kalman filter method based on minimum wheel speed shows improved accuracy, in addition to better adaptivity to vehicle reference speed. It also can be used to acceleration ship regulation （ASR） in part-time four-wheel drive vehicles.
文摘建立了四轮驱动汽车加速过程的数学模型,以滑转率为调节对象,提出一种基于模糊P ID控制的驱动防滑控制A SR算法。设计了以发动机油门为控制对象的模糊-P ID控制器并讨论了控制器切换参数的选取,并针对均一低附着路面以及分离路面在S im u link仿真环境下进行了动态仿真。对比仿真结果,表明模糊P ID控制性能优于单一的模糊控制。
