Based on the method of compound and additional conditions under the conditions of the equal temperature rise and the equal potential drop (P.D.) of resistance, the application of design software of dry-type air-core r...Based on the method of compound and additional conditions under the conditions of the equal temperature rise and the equal potential drop (P.D.) of resistance, the application of design software of dry-type air-core reactor is introduced in this thesis. The analytical methods of the inductance are also given. This approach is proved entirely feasible in theory through the simplification with Bartky transformation, and is able to quickly and accurately calculate reactor inductance. This paper presents the analytical methods of the loss of dry-type air-core reactor as well.展开更多
Compared with the traditional wet-type de-dusting technology ,the dry-type de-dusting technology is considered to be environmentally friendly and energy-saving. However, the pipes carrying the de-dusted blast fiLrnace...Compared with the traditional wet-type de-dusting technology ,the dry-type de-dusting technology is considered to be environmentally friendly and energy-saving. However, the pipes carrying the de-dusted blast fiLrnace gas (BFG) tends to be corrosive more quickly and seriously. In order to investigate the reasons for the quick corrosion, the gas pipes and auxiliary bellows installed in Baosteel' s newly built BFG dry-type de-dusting system are studied. The corrosive properties of the condensed water, such as the pH value, are measured and analyzed. Meanwhile, various factors that may influence the corrosion rate of the pipes are studied by experiment. On the basis of the investigation and research, the causes of corrosion and leakage on the pipes are discovered. It is the process of dry de-dusting that is responsible ,to a large extent, for the quick corrosion of the pipes. The equipment of spray tower is introduced and its effects are then discussed. This tower is designed to eliminate most of chloridion and neutralized the acid by spraying the alkaline water to the dedusted gas flow. The practical operation shows that the tower helps to lessen the corrosiveness of the dry de-dusted gas effectively. The last part of this study analyzes the possible impacts of the dry-type de-dusting process of the newly built blast furnace (BF) on the main BFG piping which has been in the state of being corroded for years by estimating its potential corrosion rate, and some suggestions on maintenance are given as well.展开更多
The acoustic emission (AE) method could be used to detect and locate partial discharges (PD) in cast-resin dry-type transformers.However,due to the high sound attenuation in the filled epoxy,the signal is prone to int...The acoustic emission (AE) method could be used to detect and locate partial discharges (PD) in cast-resin dry-type transformers.However,due to the high sound attenuation in the filled epoxy,the signal is prone to interference from external noises and thus,in practice,there is little possibility of detecting PD.In this study,two techniques were developed to alleviate the shortcomings of the AE method.First,a waveguide is installed on the high-voltage (HV) windings,so that the acoustic signals of PD will propagate to the AE sensors that are installed on both terminals of the waveguide.The location of the winding that has PD can then be detected from the difference in arrival time of the acoustic signals.Test results indicate that the waveguide technique is able to enhance the safety of a measurement system and offers the advantages of easy installation and higher flexibility.Second,a specially designed AE sensor pair is used to distinguish whether acoustic signals are generated by PD inside the HV winding or by the corona outside the transformers.Using these two techniques of waveguide and AE sensor pair not only greatly improves sensitivity but also increases the reliability of the measurement system.Practical test results show that the new techniques can be used to locate precisely the PD in HV windings.展开更多
文摘Based on the method of compound and additional conditions under the conditions of the equal temperature rise and the equal potential drop (P.D.) of resistance, the application of design software of dry-type air-core reactor is introduced in this thesis. The analytical methods of the inductance are also given. This approach is proved entirely feasible in theory through the simplification with Bartky transformation, and is able to quickly and accurately calculate reactor inductance. This paper presents the analytical methods of the loss of dry-type air-core reactor as well.
文摘Compared with the traditional wet-type de-dusting technology ,the dry-type de-dusting technology is considered to be environmentally friendly and energy-saving. However, the pipes carrying the de-dusted blast fiLrnace gas (BFG) tends to be corrosive more quickly and seriously. In order to investigate the reasons for the quick corrosion, the gas pipes and auxiliary bellows installed in Baosteel' s newly built BFG dry-type de-dusting system are studied. The corrosive properties of the condensed water, such as the pH value, are measured and analyzed. Meanwhile, various factors that may influence the corrosion rate of the pipes are studied by experiment. On the basis of the investigation and research, the causes of corrosion and leakage on the pipes are discovered. It is the process of dry de-dusting that is responsible ,to a large extent, for the quick corrosion of the pipes. The equipment of spray tower is introduced and its effects are then discussed. This tower is designed to eliminate most of chloridion and neutralized the acid by spraying the alkaline water to the dedusted gas flow. The practical operation shows that the tower helps to lessen the corrosiveness of the dry de-dusted gas effectively. The last part of this study analyzes the possible impacts of the dry-type de-dusting process of the newly built blast furnace (BF) on the main BFG piping which has been in the state of being corroded for years by estimating its potential corrosion rate, and some suggestions on maintenance are given as well.
基金supported by the National Science Council,Taiwan (No.NSC 92-2622-E-006-142)the Program of Top 100 Universities Advancement,Ministry of Education,Taiwan
文摘The acoustic emission (AE) method could be used to detect and locate partial discharges (PD) in cast-resin dry-type transformers.However,due to the high sound attenuation in the filled epoxy,the signal is prone to interference from external noises and thus,in practice,there is little possibility of detecting PD.In this study,two techniques were developed to alleviate the shortcomings of the AE method.First,a waveguide is installed on the high-voltage (HV) windings,so that the acoustic signals of PD will propagate to the AE sensors that are installed on both terminals of the waveguide.The location of the winding that has PD can then be detected from the difference in arrival time of the acoustic signals.Test results indicate that the waveguide technique is able to enhance the safety of a measurement system and offers the advantages of easy installation and higher flexibility.Second,a specially designed AE sensor pair is used to distinguish whether acoustic signals are generated by PD inside the HV winding or by the corona outside the transformers.Using these two techniques of waveguide and AE sensor pair not only greatly improves sensitivity but also increases the reliability of the measurement system.Practical test results show that the new techniques can be used to locate precisely the PD in HV windings.