Non-volatile dynamically switchable color display via chalcogenide stepwise cavity resonators

High-resolution multi-color printing relies upon pixelated optical nanostructures,which is crucial to promote color display by producing nonbleaching colors,yet requires simplicity in fabrication and dynamic switching.Antimony trisulfide(Sb_(2)S_(3))is a newly rising chalcogenide material that possesses prompt and significant transition of its optical characteristics in the visible region between amorphous and crystalline phases,which holds the key to color-varying devices.Herein,we proposed a dynamically switchable color printing method using Sb_(2)S_(3)-based stepwise pixelated Fabry-Pérot(FP)cavities with various cavity lengths.The device was fabricated by employing a direct laser patterning that is a less timeconsuming,more approachable,and low-cost technique.As switching the state of Sb_(2)S_(3) between amorphous and crystalline,the multi-color of stepwise pixelated FP cavities can be actively changed.The color variation is due to the profound change in the refractive index of Sb_(2)S_(3) over the visible spectrum during its phase transition.Moreover,we directly fabricated sub-50 nm nano-grating on ultrathin Sb_(2)S_(3) laminate via microsphere 800-nm femtosecond laser irradiation in far field.The minimum feature size can be further decreased down to~45 nm(λ/17)by varying the thickness of Sb_(2)S_(3) film.Ultrafast switchable Sb_(2)S_(3) photonic devices can take one step toward the next generation of inkless erasable papers or displays and enable information encryption,camouflaging surfaces,anticounterfeiting,etc.Importantly,our work explores the prospects of rapid and rewritable fabrication of periodic structures with nano-scale resolution and can serve as a guideline for further development of chalcogenide-based photonics components.

Asymmetrical Fabry-Perot cavity slot micro-ring resonator and its sensing characteristics

To achieve high quality factor and high-sensitivity refractive index sensor,a slot micro-ring resonator(MRR)based on asymmetric Fabry-Perot(FP)cavity was proposed.The structure consisted of a pair of elliptical holes to form an FP cavity and a microring resonator.The two different optical modes generated by the micro-ring resonator were destructively interfered to form a Fano line shape,which improved the system sensitivity while obtaining a higher quality factor and extinction ratio.The transmission principle of the structure was analyzed by the transfer matrix method.The transmission spectrum and mode field distribution of the proposed structure were simulated by the finite difference time domain(FDTD)method,and the key structural parameters affecting the Fano line shape in the device were optimized.The simulation results show that the quality factor of the device reached 22037.1,and the extinction ratio was 23.9 dB.By analyzing the refractive index sensing characteristics,the sensitivity of the structure was 354 nm·RIU−1,and the detection limit of the sensitivity was 2×10−4 RIU.Thus,the proposed compact asymmetric FP cavity slot micro-ring resonator has obvious advantages in sensing applications owing to its excellent performance.

Resonance suppression and electromagnetic shielding effectiveness improvement of an apertured rectangular cavity by using wall losses

The cavity-mode resonance effect could result in significant degradation of the shielding effectiveness （SE） of a shielding enclosure around its resonance frequencies. In this paper, the influence of coated wall loss on the suppression of the resonance effect is investigated. For this purpose, an equivalent circuit model is employed to analyze the SE of an apertured rectangular cavity coated with an inside layer of resistive material. The model is developed by extending Robinson＇s equivalent circuit model through incorporating the effect of the wall loss into both the propagation constant and the characteristic impedance of the waveguide. Calculation results show that the wall loss could lead to great improvement on the SE for frequencies near the resonance but almost no effect on the SE for frequencies far away from the resonance.

Design and high-power testing of offline conditioning cavity for CiADS RFQ high-power coupler

To validate the design rationality of the power coupler for the RFQ cavity and minimize cavity contamination,we designed a low-loss offline conditioning cavity and conducted high-power testing.This offline cavity features two coupling ports and two tuners,operating at a frequency of 162.5 MHz with a tuning range of 3.2 MHz.Adjusting the installation angle of the coupling ring and the insertion depth of the tuner helps minimize cavity losses.We performed electromagnetic structural and multiphysics simulations,revealing a minimal theoretical power loss of 4.3%.However,when the cavity frequency varied by110 kHz,theoretical power losses increased to10%,necessitating constant tuner adjustments during conditioning.Multiphysics simulations indicated that increased cavity temperature did not affect frequency variation.Upon completion of the offline high-power conditioning platform,we measured the transmission performance,revealing a power loss of 6.3%,exceeding the theoretical calculation.Conditioning utilized efficient automatic range scanning and standing wave resonant methods.To fully condition the power coupler,a 15°phase difference between two standing wave points in the condition-ing system was necessary.Notably,the maximum continuous wave power surpassed 20 kW,exceeding the expected target.

Effective transmittance of Fabry–Perot cavity under non-parallel beam incidence

The Fabry–Perot(FP) resonant cavity is widely used in laser and spectroscopic measurements due to its unique interference transfer function(ITF). In the ideal case of parallel incident light, the ITF of the FP resonant cavity can be expressed by the Airy function. However, in reality, it is difficult to achieve perfect parallelism with collimated beams. In this article, a theoretical model is established for non-parallel light incidence, which assumes that the non-parallel incident light is a cone-shaped beam, and the cone angle is used to quantify the non-parallelism of the beam. The transmittance function of the FP resonant cavity under non-parallel light incidence is derived. The accuracy of the model is experimentally verified. Based on this model, the effects of divergence angle, tilt angle and FP cavity parameters(reflectivity, cavity length)on the ITF are studied. The reasons for the decrease in peak value, broadening and asymmetry of the interference peak under non-parallel light incidence are explained. It is suggested that a fine balance between the interference peak and the collimation effect of the incident light should be considered in the design and application of FP resonant cavities, especially for tilted applications such as angle-scanned spectroscopy. The research results of this article have certain significance for the design and application of FP resonant cavities.

Enhanced surface plasmon interference lithography from cavity resonance in the grating slits

Surface plasmon interference lithography based on grating diffraction has been studied both theoretically and ex- perimentally in recent years. In this paper, we demonstrate that the cavity resonance in the grating slits can improve the subwavelength interference, not only the intensity but also the uniformity of the pattern. Both the typical lithography structure which merely consists of periodic metallic gratings and the modified structure equipped with a reflection layer are studied. The finite element method has been performed to study the interference pattern. Numerical simulations show that the property of the interference pattern is the optimum when cavity resonance happens. This enhancement can be applied to all the lithography structures which are based on the grating diffraction.

Analysis of iris-loaded resonance cavity in miniaturized maser

The size reduction of atomic clocks is a long-standing research issue.Many atomic clocks such as passive hydrogen masers(PHMs)and compact rubidium masers(CRMs)use iris-loaded resonance cavities(IRCs)as their microwave cavities because they can dramatically reduce the radical sizes of the atomic clocks.In this paper,the electromagnetic characteristic of the IRC is investigated by a theoretical model based on electromagnetic field theory.The formulas to calculate the resonance frequency,quality factor,and magnetic energy filling factor are presented.The relationship between the IRC structure and its electromagnetic characteristic is clarified.The theoretical calculation results accord well with the electromagnetic software simulations and experimental results.The results in this paper should be helpful in understanding the physical mechanism of the IRC and designing the atomic clocks.

Effect of Cavity Dimensions on TE_01δMode Resonance in Split-Post Dielectric Resonator Techniques

The effects of cavity dimensions on the resonance frequency and resonance strength of the TE01δmode in split postdielectric resonator (SPDR) technique are investigated by using full-wave simulations. The results of simulations provide guidance for adjusting the dimensional parameters of the set-up to ensure that a strong TE01δ resonance mode is excited. The scaled designs of SPDR fixtures for operation at frequencies that are most important for applications are presented. These designs employ two sets of dielectric resonators (DRs) that can be fabricated from the standard ceramic materials. In addition, it is demonstrated that the resonance frequency of the TE01δ mode in the fixture can be tuned by adjusting the gap of the split DR.

Mesoporous MnSiO3@Fe3O4@C Nanoparticle as p H-responsive T1-T2* Dual-modal Magnetic Resonance Imaging Contrast Agent for Tumor Diagnosis

Mesoporous structured MnSiO3@Fe3O4@C nanoparticles(NPs)were prepared via a facile and efficient strategy,with negligible cytotoxicity and minor side efforts.The as-prepared MnSiO3@Fe3O4@C NPs hold great potential in serving as pH-responsive T1-T2^*dual-modal magnetic resonance(MR)imaging contrast agents.The released Mn^2+shortened T1 relaxation time,meanwhile the superparamagnetic Fe3O4 enhanced T2 contrast imaging.The release rate of Mn ions reaches 31.66%under the condition of pH=5.0,which is similar to tumor microenvironment and organelles.Cytotoxicity assays show that MnSiO3@Fe3O4@C NPs have minor toxicity,even at high concentrations.After intravenous injection of MnSiO3@Fe3O4@C NPs,a rapid contrast enhancement in tumors was achieved with a significant enhancement of 132%after 24 h of the administration.Moreover,a significant decreasement of 53.8%was witnessed in T2 MR imaging signal.It demonstrated that MnSiO3@Fe3O4@C NPs can act as both positive and negative MR imaging contrast agents.Besides,owing to the pH-responsive degradation of mesoporous MnSiO3,MnSiO3@Fe3O4@C NPs can also be used as potential drug systems for cancer theranostics.

NOVEL MICROSTRIP DUAL-MODE BANDPASS FILTER WITH COUPLING ENHANCEMENT AND WIDEBAND SPURIOUS RESPONSE SUPPRESSION

The microstrip dual-mode filter （DMF） with conventional coupling structure has some limitations in- eluding the port coupling strength limited by fabrication tolerance and the existence of serious second order spuri- ous band. Therefore, a novel DMF with a offset-feed bended coupling structure and a stepped-impedance dual- mode resonator is proposed for coupling enhancement and spurious response suppression. Based on the analysis of the change of spur frequencies and the current distribution of spur resonant modes, all spurs near passband of the cascaded DMF can be fully suppressed by optimizing the structure parameters of parasite resonators, which bene- fits from the inherent well-controlled transmission zeros. Experimental results show that the proposed DMF ex- hibits lower insertion loss ,much sharper rate of cutoff and wider spur-free stop band compared with conventional DMF. This design is applicable for spur suppression in wideband communication.

Design and analysis of dual-mode structure repetitive control based hybrid current regulation scheme for active power filters

An all-digital hybrid current regulation scheme for the single-phase shunt active power filter （APF） is presented. The proposed hybrid current control scheme integrates the deadbeat control and the dual-mode structure repetitive control （DMRC） so that it can offer superior steady-state performance and good transient features. Unlike the conventional schemes, the proposed scheme-based APF can compensate both the odd and the even order harmonics in grid. The detailed design criteria and the stability analysis of the proposed hybrid current controller are presented. Moreover, an improved structure which incorporates the proposed hybrid controller and the resonant controller for tracking specific order harmonics is given. The relationships between the resonant controller and different repetitive control schemes are discussed. Experimental results verify the effectiveness and advantages of the proposed hybrid control scheme.

Stochastic resonance of spinor condensates in optical cavity

Stochastic resonance is a phenomenon in which adding random noise to a system enhances the detection or transmission of a weak signal. It occurs when the noise interacts with the system's nonlinearity, thus improving signal-to-noise ratio and increasing sensitivity. Although parametric resonances in an atomic spinor Bose-Einstein condensate have been investigated, the question of whether one can observe stochastic resonance in such a system persists. In this study we propose a scheme for generating stochastic resonance in a cavity-spinor Bose-Einstein condensate coupling system. We demonstrate stochastic resonance through numerical calculations using the mean-field theory and truncated Wigner approximation methods. Furthermore, the characteristics of the system's response to noise and periodic signals are studied in detail. This study unravels a new scheme for observing stochastic resonance via linking atomic many-body physics with cavity quantum electrodynamics.

Teleportation of two-atom entangled state in resonant cavity quantum electrodynamics

An alternative scheme is presented for teleportation of a two-atom entangled state in cavity quantum electrodynamics （QED）. It is based on the resonant atom-cavity field interaction. In the scheme, only one cavity is involved, and the number of the atoms needed to be detected is decreased compared with the previous scheme. Since the resonant atom-cavity field interaction greatly reduces the interaction time, the decoherence effect can be effectively suppressed during the teleportation process. The experimental feasibility of the scheme is discussed. The scheme can easily be generalized to the teleportation of N-atom Greeninger-Horne-Zeilinger （GHZ） entangled states. The number of atoms needed to be detected does not increase as the number of the atoms in the GHZ state increases.

Novel method to measure unloaded quality factor of resonant cavities at room temperature

We demonstrated a novel method to measure the unloaded quality factor(Q factor) of high-Q resonant cavities. This method was used to obtain data with low errors and calculate the unloaded Q factor. This procedure was more reliable than traditional methods. The data required for the method were near the resonant frequency,not at the half-power points of the reflection coefficient curve or Smith chart. We applied the new method to measure a resonant cavity with an unloaded Q factor of^100,000, obtaining good agreement between the measured and theoretical results.

Nonperturbative solutions to cylindrical resonant cavities with dissipative medium and imperfectly conducting walls

Cylindrical waveguides without end surfaces can serve as two-dimensional resonant cavities. In such cavities the electromagnetic oscillations corresponding to an eigenfrequency can always be taken as TM or TE modes even when the walls have a finite conductivity and the medium is absorptive. This paper obtains analytic solutions to the field equations when the cylinder has a circular cross section. Some nonperturbative conclusions are drawn from the eigenvalue equation. Approximate analytic results for the resonant frequencies are obtained when the absorption of the medium is small and the walls are good conductors. Stability of the eigen modes is discussed. Similar results for the coaxial line are presented.

Magnetically-coated silica nanospheres for dual-mode imaging at low ultrasound frequency

AIM: To experimentally investigate the acoustical behavior of different dual-mode nanosized contrast agents(NPCAs) for echographic medical imaging at low ultrasound(US) frequency. METHODS: We synthesized three different nanosized structures:(1) Pure silica nanospheres(SiNSs);(2) FePt-iron oxide(FePt-IO)-coated SiNSs; and(3) IOcoated SiNSs, employing three different diameter of SiNS-core(160, 330 and 660 nm). Tissue mimicking phantoms made of agarose gel solution containing 5 mg of different NPCAs in 2 mL-Eppendorf tubes, were insonified by a commercial echographic system at three different low US pulse values(2.5, 3.5 and 4.5 MHz). The raw radiofrequency signal, backscattered from each considered NPCA containing sample, has been processed in order to calculate the US average backscatter intensity and compare the acoustic behavior of the different NPCA types. RESULTS: The highest US contrast was exhibited by pure SiNSs; FePt-IO-coated SiNSs acoustical behavior followed a similar trend of pure SiNSs with a slight difference in terms of brightness values. The acoustic response of the examined NPCAs resulted function of both SiNS diameter and US frequency. Specifically, higher US frequencies determined higher value of the backscatter for a given SiNS diameter. Frequencydependent enhancement was marked for pure SiNSs and became less remarkable for FePt-IO-coated SiNSs, whereas IO-coated SiNSs resulted almost unaffected by such frequency variations. Pure and FePt-IO-coated SiNSs evidenced an image backscatter increasing with the diameter up to 330 nm. Conversely, among the types of NPCA tested, IO-coated SiNSs showed the lowest acoustical response for each synthesized diameter and employed US frequency, although a diameter-dependent raising trend was evidenced. CONCLUSION: The US characterization of magnetically covered SiNS shows that FePt-IO, rather than IO, was the best magnetic coating for realizing NPCAs suitable for dual mode imaging of deep organs, combining US and magnetic resonance imaging.

Optimization of Sound Absorption and Insulation Performances of a Dual-Cavity Resonant Micro-Perforated Plate

This study investigates a dual-cavity resonant composite sound-absorbing structure based on a micro-perforated plate.Using the COMSOL impedance tube model,the effects of various structural parameters on sound absorption and sound insulation performances are analyzed.Results show that the aperture of the micro-perforated plate has the greatest influence on the sound absorption coefficient;the smaller the aperture,the greater is this coefficient.The thickness of the resonance plate has the most significant influence on the sound insulation and resonance frequency;the greater the thickness,the wider the frequency domain in which sound insulation is obtained.In addition,the effect of filling the structural cavity with porous foam ceramics has been studied,and it has been found that the porosity and thickness of the porous material have a significant effect on the sound absorption coefficient and sound insulation,while the pore size exhibits a limited influence.

A research on high-temperature permittivity and loss tangent of low-loss dielectric by resonant-cavity technique

Resonant-cavity technique was introduced to measure the permittivity and loss tangent of low-loss dielectrics. The dielectric properties at 9-10 GHz are measured accurately at the temperature up to 800 ℃ by the resonant cavity technique. The only electrical parameters that need to be measured are quality factors （Q） and resonant length （L） of resonant cavity loaded and unloaded with dielectric sample. Moreover, the error caused by thermal expansion effect was resolved by error analysis and experimental calibration.

High-performance Refractive Index Sensor Based on Photonic Crystal Single Mode Resonant Micro-cavity

An effective refractive index sensor built with square lattice photonic crystal is proposed,which can be applicable to photonic integrated circuits.Two photonic crystal waveguides rather than conventional ridge waveguides are used as entrance/exit waveguides to the micro-cavity.Three layers of photonic lattice are set between the photonic crystal waveguides and the micro-cavity to achieve both a high transmission and a high sensitivity.The plane wave method is utilized to calculate the disperse curves and the finite difference time domain scheme is employed to simulate the light propagation.At the resonant wavelength of about 1500 nm,the resonant wavelength shifts up by 0.7 nm for each increment of Δn=0.001.A transmission of more than 0.75 is observed.Although the position disorder of the photonic crystal doesn't affect the sensitivity of the sensor, the transmission reduces rapidly as the disorder increases.

Preparation of W state in resonant bimodal cavity quantum electrodynamics

A scheme is proposed for generating entangled W states with four cavity modes. In this scheme, we send a V-type three-level atom through two identical two-mode cavities in succession. After the atom exits from the second cavity, the four cavity modes are prepared in the W state. On the other hand we can obtain three-atom W states by sending three V-type three-level atoms through a two-mode cavity in turn. The present scheme does not require conditional measurement, and it is easily generalized to preparing 2n-mode W states and n-atom W states.