The hydrogen trapping phenomena in two bainite/martensite dual-phase high strength steels(U20Si and U20DSi)were investigated by electrochemical permeation technique.The hydrogen diffusivity was calculated from data of...The hydrogen trapping phenomena in two bainite/martensite dual-phase high strength steels(U20Si and U20DSi)were investigated by electrochemical permeation technique.The hydrogen diffusivity was calculated from data of permeation delay time,and the diffusion coefficient in U20 Si is far less than that in U20 DSi.Moreover,the hydrogen diffusivity decreases as the volume percent of retained austenite increases.The experiment results show that there are different hydrogen trappings and different volume percents of retained austenite in U20 Si and U20 DSi.The retained austenite is precipitated as films.The trap binding energy for the retained austenite and hydrogen is calculated to be 40.4kJ·mol-1.展开更多
Influence of microstructure of the experimental steels on the corrosion fatigue behavior in 3.5% of NaCl aqueous solution was studied.Experimental results show that compared with the full martensite（FM）steel,the car...Influence of microstructure of the experimental steels on the corrosion fatigue behavior in 3.5% of NaCl aqueous solution was studied.Experimental results show that compared with the full martensite（FM）steel,the carbide-free bainite/martensite（CFB/M）steel has higher corrosion fatigue strength and corrosion fatigue crack threshold（ΔKthcf）,and lower corrosion crack propagation rate [（da/dN）cf].展开更多
The quantitative analysis of substructure in the martensite/bainite mixed structure, which is obtained from low-carbon NiCrMoV steels under different cooling conditions, was made by means of optical microscope （OM）,...The quantitative analysis of substructure in the martensite/bainite mixed structure, which is obtained from low-carbon NiCrMoV steels under different cooling conditions, was made by means of optical microscope （OM）, scanning electron microscope （SEM）, electron backscatter diffraction （EBSD）, and transmission electron microscope （TEM）, in order to research the effect on toughness. The test results indicate that the toughness of the steel is en- hanced with the decrease in the packet and block size under the condition of the same prior austenite grain size mixed with different ratios of martensite and bainite while the lath width is about 0.38μm. The calculation shows that both the packet and block boundaries have the same hindering effect on crack extension. Furthermore, the effect of the block width on impact energy is much larger than that of the packet. Therefore, the block can be used as microstruc- tural substructure to affect the toughness in low-carbon martensite steels, suggesting that the block size is ＂the effective grain size＂ for controlling toughness.展开更多
During the incubation period of isothermal treatment（or aging） within the bainitic transformation temperature range in a salt bath （or quenching in water） immediately after solution treatment, not only are the def...During the incubation period of isothermal treatment（or aging） within the bainitic transformation temperature range in a salt bath （or quenching in water） immediately after solution treatment, not only are the defects formed at high temperatures maintained, but new defects can also be generated in alloys, iron alloys and steels. Due to the segregation of the solute atoms near defects through diffusion, this leads to non-uniform distributions of solute atoms in the parent phase with distinct regions of both solute enrichment and solute depletion. It is proposed that when the Ms temperature at the solute depleted regions is equal to or higher than the isothermal （or aged） temperature,nucleation of bainite occurs within these solute depleted regions in the manner of martensitic shear. Therefore it is considered that, at least in steel, iron and copper alloy systems, bainite is formed through a shear mechanism within solute depleted regions, which is controlled and formed by the solute atoms diffusion in the parent phase.展开更多
基金Item Sponsored by Ministry of Science and Technology of China(G1998061513)
文摘The hydrogen trapping phenomena in two bainite/martensite dual-phase high strength steels(U20Si and U20DSi)were investigated by electrochemical permeation technique.The hydrogen diffusivity was calculated from data of permeation delay time,and the diffusion coefficient in U20 Si is far less than that in U20 DSi.Moreover,the hydrogen diffusivity decreases as the volume percent of retained austenite increases.The experiment results show that there are different hydrogen trappings and different volume percents of retained austenite in U20 Si and U20 DSi.The retained austenite is precipitated as films.The trap binding energy for the retained austenite and hydrogen is calculated to be 40.4kJ·mol-1.
基金Item Sponsored by State Key Development Programfor Basic Research of China(2004CB619105)
文摘Influence of microstructure of the experimental steels on the corrosion fatigue behavior in 3.5% of NaCl aqueous solution was studied.Experimental results show that compared with the full martensite（FM）steel,the carbide-free bainite/martensite（CFB/M）steel has higher corrosion fatigue strength and corrosion fatigue crack threshold（ΔKthcf）,and lower corrosion crack propagation rate [（da/dN）cf].
文摘The quantitative analysis of substructure in the martensite/bainite mixed structure, which is obtained from low-carbon NiCrMoV steels under different cooling conditions, was made by means of optical microscope （OM）, scanning electron microscope （SEM）, electron backscatter diffraction （EBSD）, and transmission electron microscope （TEM）, in order to research the effect on toughness. The test results indicate that the toughness of the steel is en- hanced with the decrease in the packet and block size under the condition of the same prior austenite grain size mixed with different ratios of martensite and bainite while the lath width is about 0.38μm. The calculation shows that both the packet and block boundaries have the same hindering effect on crack extension. Furthermore, the effect of the block width on impact energy is much larger than that of the packet. Therefore, the block can be used as microstruc- tural substructure to affect the toughness in low-carbon martensite steels, suggesting that the block size is ＂the effective grain size＂ for controlling toughness.
基金This work was supported by the National Natural Science Foundation of China(Grant No.59171031)
文摘During the incubation period of isothermal treatment（or aging） within the bainitic transformation temperature range in a salt bath （or quenching in water） immediately after solution treatment, not only are the defects formed at high temperatures maintained, but new defects can also be generated in alloys, iron alloys and steels. Due to the segregation of the solute atoms near defects through diffusion, this leads to non-uniform distributions of solute atoms in the parent phase with distinct regions of both solute enrichment and solute depletion. It is proposed that when the Ms temperature at the solute depleted regions is equal to or higher than the isothermal （or aged） temperature,nucleation of bainite occurs within these solute depleted regions in the manner of martensitic shear. Therefore it is considered that, at least in steel, iron and copper alloy systems, bainite is formed through a shear mechanism within solute depleted regions, which is controlled and formed by the solute atoms diffusion in the parent phase.
