One of the critical aspects in mine design is slope stability analysis and the determination of stable slopes. In the Chador- Malu iron ore mine, one of the most important iron ore mines in central Iran, it was consid...One of the critical aspects in mine design is slope stability analysis and the determination of stable slopes. In the Chador- Malu iron ore mine, one of the most important iron ore mines in central Iran, it was considered vital to perform a comprehensive slope stability analysis. At first, we divided the existing rock hosting pit into six zones and a geotechnical map was prepared. Then, the value of MRMR （Mining Rock Mass Rating） was determined for each zone. Owing to the fact that the Chador-Malu iron ore mine is located in a highly tectonic area and the rock mass completely crushed, the Hoek-Brown failure criterion was found suitable to estimate geo-mechanical parameters. After that, the value of cohesion （c） and friction angle （tp） were calculated for different geotechnical zones and relative graphs and equations were derived as a function of slope height. The stability analyses using numerical and limit equilibrium methods showed that some instability problems might occur by increasing the slope height. Therefore, stable slopes for each geotechnical zone and prepared sections were calculated and presented as a function of slope height.展开更多
This paper describes a precise method combining numerical analysis and limit equilibrium theory to determine potential slip surfaces in soil slopes. In this method, the direction of the critical slip surface at any po...This paper describes a precise method combining numerical analysis and limit equilibrium theory to determine potential slip surfaces in soil slopes. In this method, the direction of the critical slip surface at any point in a slope is determined using the Coulomb’s strength principle and the extremum principle based on the ratio of the shear strength to the shear stress at that point. The ratio, which is considered as an analysis index, can be computed once the stress field of the soil slope is obtained. The critical slip direction at any point in the slope must be the tangential direction of a potential slip surface passing through the point. Therefore, starting from a point on the top of the slope surface or on the horizontal segment outside the slope toe, the increment with a small distance into the slope is used to choose another point and the corresponding slip direction at the point is computed. Connecting all the points used in the computation forms a potential slip surface exiting at the starting point. Then the factor of safety for any potential slip surface can be computed using limit equilibrium method like Spencer method. After factors of safety for all the potential slip surfaces are obtained, the minimum one is the factor of safety for the slope and the corresponding potential slip surface is the critical slip surface of the slope. The proposed method does not need to pre-assume the shape of potential slip surfaces. Thus it is suitable for any shape of slip surfaces. Moreover the method is very simple to be applied. Examples are presented in this paper to illustrate the feasibility of the proposed method programmed in ANSYS software by macro commands.展开更多
The stability of an inner dump slope was investigated under the efect of coal pillar support considering the development position of dumping.Based on the instability mechanism and load distribution characteristics of ...The stability of an inner dump slope was investigated under the efect of coal pillar support considering the development position of dumping.Based on the instability mechanism and load distribution characteristics of the supporting coal pillar,the three-dimensional mechanical efects of the supporting coal pillar are characterized.Using the two-dimensional equivalent principle and the residual thrust method,the stability of the inner dump slope was analyzed under the efect of pillar support at diferent dump development positions.The quantitative efects of various factors on the inner dump slope stability were revealed,and the coal pillar shape parameters were optimized through numerical simulations.The results indicate that the slope stability coefcient is linearly related to the top width and height of the coal pillar,slope angle,and base inclination angle,and has an exponential relation with the coal pillar strike length and slope height increment.There are quadratic and absolute value relations with the coal pillar outer and the inner bottom angle,respectively.The top width of the coal pillar in the inner dump of Shengli East No.2 open-pit coal mine should be at a level of+824 m,and the optimal top width and height are 15 and 36.7 m,respectively.The instability mechanism of the supporting and retaining coal pillar obtained by numerical simulations and the stability of the inner dump are in good agreement with the theoretical analysis.Our results provide a theoretical basis for the design,treatment,and safe implementation of similar open-pit mine slope engineering.展开更多
The engineering geology and hydrogeology in the southern slope of Chengmenshan copper mine are very complicated,because there is a soft-weak layer between two kinds of sandstones.Field investigations demonstrate that ...The engineering geology and hydrogeology in the southern slope of Chengmenshan copper mine are very complicated,because there is a soft-weak layer between two kinds of sandstones.Field investigations demonstrate that some instability problems might occur in the slope.In this research,the southern slope,which is divided into six sections(I-0,I-1,I-2,II-0,II-1 and II-2),is selected for slope stability analysis using limit equilibrium and numerical method.Stability results show that the values of factor of safety(FOS) of sections I-0,I-1 and I-2 are very low and slope failure is likely to happen.Therefore reinforcement subjected to seismic,water and weak layer according to sections were carried out to increase the factor of safety of the three sections,two methods were used;grouting with hydration of cement and water to increase the cohesion(c) and pre-stressed anchor.Results of reinforcement showed that factor of safety increased more than 1.15.展开更多
Regardless of beneficial associated with internal waste dump (IWD) method, practices of this method within boundaries of pit-slope have some serious problems on stability issues due to this area is zone of potential f...Regardless of beneficial associated with internal waste dump (IWD) method, practices of this method within boundaries of pit-slope have some serious problems on stability issues due to this area is zone of potential failure. This zone is known as dynamic reactive zone which is easy to deform by external force, and inherent dangers of failure posing a threat to slope. Therefore, it is paramount to study the induced shear stress behavior in this zone particularly when IWD method is adopted within this zone. In this paper, a numerical study for investigating IWD-induced shear stress behavior has been carried out using Finite Element Method (FEM) with Strength Reduction approach. Different scenarios as per pit-slope depths, IWD heights and buffer zone lengths have been accounted and simulated using PHASE 2 to understand changes in induced shear stress imposed on the pit-slope. It is found that shear stress imposed on pit slope seems change dramatically with increasing IWD height for case of buffer zone length is less than 100-m-long.展开更多
A reservoir landslide not only reduces the water storage capacity, but also causes extensive damages to the dam body, power/water transmission lines, roads, and other infrastructures. The Latian Dam, located 35 km nor...A reservoir landslide not only reduces the water storage capacity, but also causes extensive damages to the dam body, power/water transmission lines, roads, and other infrastructures. The Latian Dam, located 35 km north east of Tehran （Iran）, is one of the cases which has encountered serious problems with instability of its rock abutments. This paper addresses the stability analysis of the right abutment of the Latian Dam using limit equilibrium and numerical methods. Geomechanical characteristics of the rock abutment were first estimated based on engineering classification of the rock mass. Different search methods were examined for locating the critical circular/non-circular slip surface in conjunction with the general limit equilibrium method. The effect of variabi]ity of rock mass properties, water table, and earthquake load on the factor of safety （FS） and probability of failure （PF） was studied. In the event of rapid drawdown in the reservoir, the limit equilibrium analysis calculated FS=1.067 and PF=21.1%, and the numerical analysis returned FS=1.01. The results of the analyses suggest that the right abutment of the Latian Dam is prone to slide and needs treatment. Investigations demonstrated that a slope reduction by 15° at the upper part of the abutment would meet stability conditions even in the worst-case scenario （FS=1.297 and PF=2.07%）.展开更多
This paper studies the stability of jointed rock slopes by using our improved three-dimensional discrete element methods (DEM) and physical modeling. Results show that the DEM can simulate all failure modes of rock sl...This paper studies the stability of jointed rock slopes by using our improved three-dimensional discrete element methods (DEM) and physical modeling. Results show that the DEM can simulate all failure modes of rock slopes with different joint configurations. The stress in each rock block is not homogeneous and blocks rotate in failure development. Failure modes depend on the configuration of joints. Toppling failure is observed for the slope with straight joints and sliding failure is observed for the slope with staged joints. The DEM results are also compared with those of limit equilibrium method (LEM). Without considering the joints in rock masses, the LEM predicts much higher factor of safety than physical modeling and DEM. The failure mode and factor of safety predicted by the DEM are in good agreement with laboratory tests for any jointed rock slope.展开更多
文摘One of the critical aspects in mine design is slope stability analysis and the determination of stable slopes. In the Chador- Malu iron ore mine, one of the most important iron ore mines in central Iran, it was considered vital to perform a comprehensive slope stability analysis. At first, we divided the existing rock hosting pit into six zones and a geotechnical map was prepared. Then, the value of MRMR （Mining Rock Mass Rating） was determined for each zone. Owing to the fact that the Chador-Malu iron ore mine is located in a highly tectonic area and the rock mass completely crushed, the Hoek-Brown failure criterion was found suitable to estimate geo-mechanical parameters. After that, the value of cohesion （c） and friction angle （tp） were calculated for different geotechnical zones and relative graphs and equations were derived as a function of slope height. The stability analyses using numerical and limit equilibrium methods showed that some instability problems might occur by increasing the slope height. Therefore, stable slopes for each geotechnical zone and prepared sections were calculated and presented as a function of slope height.
文摘This paper describes a precise method combining numerical analysis and limit equilibrium theory to determine potential slip surfaces in soil slopes. In this method, the direction of the critical slip surface at any point in a slope is determined using the Coulomb’s strength principle and the extremum principle based on the ratio of the shear strength to the shear stress at that point. The ratio, which is considered as an analysis index, can be computed once the stress field of the soil slope is obtained. The critical slip direction at any point in the slope must be the tangential direction of a potential slip surface passing through the point. Therefore, starting from a point on the top of the slope surface or on the horizontal segment outside the slope toe, the increment with a small distance into the slope is used to choose another point and the corresponding slip direction at the point is computed. Connecting all the points used in the computation forms a potential slip surface exiting at the starting point. Then the factor of safety for any potential slip surface can be computed using limit equilibrium method like Spencer method. After factors of safety for all the potential slip surfaces are obtained, the minimum one is the factor of safety for the slope and the corresponding potential slip surface is the critical slip surface of the slope. The proposed method does not need to pre-assume the shape of potential slip surfaces. Thus it is suitable for any shape of slip surfaces. Moreover the method is very simple to be applied. Examples are presented in this paper to illustrate the feasibility of the proposed method programmed in ANSYS software by macro commands.
基金supported by the National Natural Science Foundation of China(51874160)Liaoning BaiQianWan Talents Program,and Discipline Innovation Team of Liaoning Technical University(LNTU20TD-01).
文摘The stability of an inner dump slope was investigated under the efect of coal pillar support considering the development position of dumping.Based on the instability mechanism and load distribution characteristics of the supporting coal pillar,the three-dimensional mechanical efects of the supporting coal pillar are characterized.Using the two-dimensional equivalent principle and the residual thrust method,the stability of the inner dump slope was analyzed under the efect of pillar support at diferent dump development positions.The quantitative efects of various factors on the inner dump slope stability were revealed,and the coal pillar shape parameters were optimized through numerical simulations.The results indicate that the slope stability coefcient is linearly related to the top width and height of the coal pillar,slope angle,and base inclination angle,and has an exponential relation with the coal pillar strike length and slope height increment.There are quadratic and absolute value relations with the coal pillar outer and the inner bottom angle,respectively.The top width of the coal pillar in the inner dump of Shengli East No.2 open-pit coal mine should be at a level of+824 m,and the optimal top width and height are 15 and 36.7 m,respectively.The instability mechanism of the supporting and retaining coal pillar obtained by numerical simulations and the stability of the inner dump are in good agreement with the theoretical analysis.Our results provide a theoretical basis for the design,treatment,and safe implementation of similar open-pit mine slope engineering.
基金support of Jiangxi Copper Company Limited (Chengmenshan Copper Mine)China Nerin Engineering Co.,Ltd.supported by the National Natural Science Foundation of China (No.11372363)
文摘The engineering geology and hydrogeology in the southern slope of Chengmenshan copper mine are very complicated,because there is a soft-weak layer between two kinds of sandstones.Field investigations demonstrate that some instability problems might occur in the slope.In this research,the southern slope,which is divided into six sections(I-0,I-1,I-2,II-0,II-1 and II-2),is selected for slope stability analysis using limit equilibrium and numerical method.Stability results show that the values of factor of safety(FOS) of sections I-0,I-1 and I-2 are very low and slope failure is likely to happen.Therefore reinforcement subjected to seismic,water and weak layer according to sections were carried out to increase the factor of safety of the three sections,two methods were used;grouting with hydration of cement and water to increase the cohesion(c) and pre-stressed anchor.Results of reinforcement showed that factor of safety increased more than 1.15.
文摘Regardless of beneficial associated with internal waste dump (IWD) method, practices of this method within boundaries of pit-slope have some serious problems on stability issues due to this area is zone of potential failure. This zone is known as dynamic reactive zone which is easy to deform by external force, and inherent dangers of failure posing a threat to slope. Therefore, it is paramount to study the induced shear stress behavior in this zone particularly when IWD method is adopted within this zone. In this paper, a numerical study for investigating IWD-induced shear stress behavior has been carried out using Finite Element Method (FEM) with Strength Reduction approach. Different scenarios as per pit-slope depths, IWD heights and buffer zone lengths have been accounted and simulated using PHASE 2 to understand changes in induced shear stress imposed on the pit-slope. It is found that shear stress imposed on pit slope seems change dramatically with increasing IWD height for case of buffer zone length is less than 100-m-long.
文摘A reservoir landslide not only reduces the water storage capacity, but also causes extensive damages to the dam body, power/water transmission lines, roads, and other infrastructures. The Latian Dam, located 35 km north east of Tehran （Iran）, is one of the cases which has encountered serious problems with instability of its rock abutments. This paper addresses the stability analysis of the right abutment of the Latian Dam using limit equilibrium and numerical methods. Geomechanical characteristics of the rock abutment were first estimated based on engineering classification of the rock mass. Different search methods were examined for locating the critical circular/non-circular slip surface in conjunction with the general limit equilibrium method. The effect of variabi]ity of rock mass properties, water table, and earthquake load on the factor of safety （FS） and probability of failure （PF） was studied. In the event of rapid drawdown in the reservoir, the limit equilibrium analysis calculated FS=1.067 and PF=21.1%, and the numerical analysis returned FS=1.01. The results of the analyses suggest that the right abutment of the Latian Dam is prone to slide and needs treatment. Investigations demonstrated that a slope reduction by 15° at the upper part of the abutment would meet stability conditions even in the worst-case scenario （FS=1.297 and PF=2.07%）.
文摘This paper studies the stability of jointed rock slopes by using our improved three-dimensional discrete element methods (DEM) and physical modeling. Results show that the DEM can simulate all failure modes of rock slopes with different joint configurations. The stress in each rock block is not homogeneous and blocks rotate in failure development. Failure modes depend on the configuration of joints. Toppling failure is observed for the slope with straight joints and sliding failure is observed for the slope with staged joints. The DEM results are also compared with those of limit equilibrium method (LEM). Without considering the joints in rock masses, the LEM predicts much higher factor of safety than physical modeling and DEM. The failure mode and factor of safety predicted by the DEM are in good agreement with laboratory tests for any jointed rock slope.
