Electromagnetic responses on microstructures of duplex stainless steels based on 3D cellular and electromagnetic sensor finite element models

Microstructures determine mechanical properties of steels,but in actual steel product process it is difficult to accurately control the microstructure to meet the requirements.General microstructure characterization methods are time consuming and results are not rep-resentative for overall quality level as only a fraction of steel sample was selected to be examined.In this paper,a macro and micro coupled 3D model was developed for nondestructively characterization of steel microstructures.For electromagnetic signals analysis,the relative permeability value computed by the micro cellular model can be used in the macro electromagnetic sensor model.The effects of different microstructure components on the relative permeability of duplex stainless steel(grain size,phase fraction,and phase distribu-tion)were discussed.The output inductance of an electromagnetic sensor was determined by relative permeability values and can be val-idated experimentally.The findings indicate that the inductance value of an electromagnetic sensor at low frequency can distinguish dif-ferent microstructures.This method can be applied to real-time on-line characterize steel microstructures in process of steel rolling.

Progress in weldability research of duplex stainless steels

Duplex stainless steels(DSSs)show better corrosion resistance with higher strength than traditional austenite stainless steels in many aggressive environments,and can be welded properly with almost every welding processes,if proper heat input is provided.Progresses of research works on weldability of DSSs in recent years are reviewed in this paper.Balance control of ferrite/austenite phases is most important for DSSs welding.The phases balance can be controlled with filler materials,nitrogen addition in shielding gas,heat input,post weld heat treatment,and alternating magnetic field.Too high cooling rate results in not only extra ferrite,but also chromium nitride precipitation.While too low cooling rate or heating repeatedly results in precipitation of secondary austenite and intermetallic compounds.In both situations,mechanical properties and corrosion resistance of the DSS joints deteriorate.Recommended upper and lower limits of heat input and maximum interpass temperature should be observed.

Characteristics of microstructure and performance of laser-treated electroless Ni-P/Ni-W-P duplex coatings

Characteristics of microstructures of electroless Ni-P/Ni-W-P duplex coatings were investigated using SEM/EDX and XRD analysis techniques. Microhardness and wear behaviour of the coatings before and after laser crystallization were evaluated by measurements of hardnesses of coating surface and cross-section, and by unlubricated friction and wear experiments. The results indicate that it is possible to prepare electroless Ni-P/Ni-W-P duplex coatings by sequential immersion in two different plating baths. After laser crystallization, the microstructures of electroless Ni-P/Ni-W-P duplex coatings present the characteristics of higher degree of crystallization and larger grain size for outer layer Ni-W-P than inner Ni-P, but outer layer has a higher hardness. The wear resistance of laser-treated duplex coatings in a given process parameter conditions is superior to the as-plated ones. Laser treatment was performed directly in air without argon protection, which provides the possibility for application of industrialized production.

老年脑缺血患者颅外段颈动脉的Duplex、MRA、DSA检查结果分析（附105例报告）

本文报告１０５例老年脑缺血患者作颅外段颈动脉彩色超声（Ｄｕｐｌｅｘ）或／和磁共振造影（ＭＲＡ）、数控减影血管造影（ＤＳＡ）、手术探查的检查结果。甲组短暂性脑缺血（ＴＩＡ）患者７７例，经上述检查发现颈动脉存在不同程度的斑块性狭窄有４４例（５１．１％），乙组脑梗塞恢复后患者２８例，颈动脉存在不同程度狭窄有１４例（５０．０％）。全组１０５例检出颈动脉有斑块性狭窄５８例（５５．２％）。作者在讨论中指出对脑缺血患者的颈动脉病变的筛选检查方法首选为彩色超声扫描。作者认为确诊颈动脉存在７０％以上狭窄者，颈动脉内膜剥脱术是最好的治疗方法。

In Band Full Duplex (IBFD) Technology for Next Generation Wireless Networks: A Survey in Cellular Networks

Next-Generation(NextG)wireless communication networks with their widespread applications require high data rates,seamless connectivity and high quality of service(QoS).To cope up with an unprecedented rise of data hungry applications,users demand more spectral resources imposing a limitation on available wireless spectrum.One of the potential solutions to address the spectrum scarce issue is to incorporate in band full duplex(IBFD)or full duplex(FD)paradigm in next generation networks including 5G new radio(NR).Recently,FD has gained the research interest in cellular networks for its potential to double the wireless link capacity and enhancing spectral efficiency(SE).In half duplex(HD)cellular networks,base stations(BSs)can either perform uplink(UL)or downlink(DL)transmission at a particular time instant leading to reduced throughput levels.Due to the advancement in the self interference reduction(SIR)techniques,full duplex base stations(FD-BSs)can be employed to allow simultaneous UL and DL transmissions at the same time–frequency resources as compared to its HD counterpart.It ideally achieves twice the throughput without any additional complexity at user-equipment(UE).This paper covers a detailed survey on FD cellular networks.A series of SIR approaches,UE-UE mitigation techniques are summarized.Various existing MAC protocols and antenna architectures for FD cellular networks are outlined.An overview of security aspects for FD in cellular networks is also presented.Lastly,various open issues and possible research directions are brought up for FD cellular networks.

Time-Hopping Sequence Design for Virtual Full Duplex via Rapid On-Off-Division Duplex

To achieve virtual full-duplex(VFD)communication using half-duplex radios,the rapid on-off-division(RODD)technique has been proposed in recent years.The time-hopping(TH)sequence is critical to controlling self-interference introduced in the paradigm.By constructing the collision model with a symbol level time scale,the periodic collision correlation function properties are introduced as the performance metric for the TH sequence in the RODD system.To achieve the best VFD performance,an optimization-based method for TH sequence design is proposed.In addition,the conventional TH frame structure design for RODD system is improved.Numerical simulations are presented to demonstrate that the proposed approach can significantly increase system performance.Results indicate that the TH sequence design is very effective for the RODD system.

Analysis of RF Feedback Chain Isolation in Wireless Co-Time Co-Frequency Full Duplex

By employing a radio frequency(RF) feedback chain, the self-interference can be canceled efficiently in co-time co-frequency full duplex(CCFD). However, the evitable signal crosstalk which is caused by the imperfect RF feedback chain isolation usually damages the self-interference cancelation(SIC) performance. To deal with this problem, firstly, we analyze the impact of RF feedback chain isolation on SIC performance. Then a digital preprocessing scheme with RF feedback chain is proposed in the multiple-antenna CCFD architecture. Using both analytical and experimental methods, we find that the proposed scheme achieves a better performance on SIC.

Identification of Orientia tsutsugamushi,spotted fever group and typhus group Rickettsia by duplex and nested PCR methods

Objective:To identify members of genera of rickettsia and O.tsutsugammhi simultaneously.Methods:Rapid and duplex and nested PCR methods have been established by designing primers based on the conserved regions of heat shock protein GroEL gene.345 mouse viscera samples including liver,spleen and kidney,96 Xenopsylla cheopis and 32 chiggers collected from Hongta areas of Yuxi city,Yunnan province were tested by the new PCR methods.Results:The result of the study showed that the new PCR methods could identify most members of genera -Rickettsia and Orientia simultaneously with 100%specificity and its sensitivity could test one copy per microliter.The results of detection prevalence of rickettsioses in mouse,flea and mites DNA samples showed that the total rickettsia infection rate in mouse was 34.78%(120/345).The total infection rates in R.typhi,O.t Karp and R.sibirica of mouse samples were 28.12%(97/345),19.71%(68/345) and O. 29%(1/345) respectively.Co-infection rates in R.typhi and 0.t Karp of mouse samples were 13.33%(46/ 345).O.t Karp type has been the main epidemic strain in these areas.Conclusion:We concluded that this PCR method could be used to detect multi-genera rickettsia simultaneously.Molecular evidences provided in this and previous studies strongly support that Hongta areas of Yuxi city are a natural focus for typhus and scrub typhus with the common occurrence of their confection.

Duplex PCR快速检测松材线虫

利用duplexPCR技术对松材线虫 (Bursaphelenchusxylophilus)与拟松材线虫 (B .mu cronatus)的rDNA部分核苷酸序列扩增。根据松材线虫与拟松材线虫的ITS1序列区别 ,设计出特异性引物 ,检测松材线虫的存在 ;在 5 8S ,2 8S保守序列区设计通用引物 。

Hot deformation behavior of microstructural constituents in a duplex stainless steel during high-temperature straining

The hot deformation characteristics of 1.4462 duplex stainless steel （DSS） were analyzed by considering strain partitioning between austenite and ferrite constituents. The individual behavior of ferrite and austenite in microstructure was studied in an iso-stress condition. Hot compression tests were performed at temperatures of 800-1100~C and strain rates of 0.001-1 s-1. The flow stress was modeled by a hyperbolic sine constitutive equation, the corresponding constants and apparent activation energies were determined for the studied alloys. The constitutive equation and law of mixture were used to measure the contribution factor of each phase at any given strain. It is found that the contribution factor of ferrite exponentially declines as the Zener-HoUomon parameter （Z） increases. On the contrary, the austenite contribution polynomially increases with the increase of Z. At low Z values below 2.6. x 1015 （lnZ---35.5）, a negative contribution factor is determined for austenite that is attributed to dynamic recrystallization. At high Z values, the contribution factor of austenite is about two orders of magnitude greater than that of ferrite, and therefore, austenite can accommodate more strain. Microstructural characterization via electron back-scattered diffraction （EBSD） confirms the mechanical results and shows that austenite recrystallization is possible only at high temperature and low strain rate.

Effect of Temperature and Cl^- Concentration on Pitting of 2205 Duplex Stainless Steel

The electrochemical behaviors of 2205 duplex stainless steel in NaCl solution with different temperatures and concentrations were studied by gravimetric tests, potentiodynamic polarization, electrochemical impedance spectroscopy and scanning electron microscopy. The experinental results show that temperature and chloride concentration have a great influence on the pitting resistance of 2205 duplex stainless steels. They not only effect the corrosion rate of pitting, but also change the shape of the pits. When NaCl solution was in low concentration and temperature below the critical pitting temperature, pits were very small and scattered with hemisphere-like shape. On the contrary, the pits of 2205 duplex stainless steel were large and sometimes had a lacy cover when the NaCl concentration was higher and the temperature was 70℃.

A duplex PCR for the rapid and simultaneous detection of Brucella spp.in human blood samples

Objective:To design a duplex PCR for rapid and simultaneous detection of Brucella species, in human blood samples.Methods:Fifty-two peripheral bloods samples were collected from suspicious patients with brucellosis.Following DNA extraction,PCR assay were performed, using three primers that could simultaneously identify and differentiate three major species of pathogenic Brucella in humans and animals.Results:Of the 52 peripheral bloods samples tested, 25 sample(48%) showed positive reactions in PCR.Twelve samples were positive for Brucella abortus(B.abortus)(23%,13 for Brucella melUensis(B.melUensis)(25%) and 0 for Brucella ovis (6.ovis)(Ow.Conclusions:This work de=monstrates dial in case where specific primers were utilized,duplex PCR has proved to be a simple,fast,and relatively inexpensive method for simultaneous detection of important species of Brucella in clinical samples.

Optimization of process parameters of the activated tungsten inert gas welding for aspect ratio of UNS S32205 duplex stainless steel welds

The activated TIG(ATIG) welding process mainly focuses on increasing the depth of penetration and the reduction in the width of weld bead has not been paid much attention.The shape of a weld in terms of its width-to-depth ratio known as aspect ratio has a marked influence on its solidification cracking tendency.The major influencing ATIG welding parameters,such as electrode gap,travel speed,current and voltage,that aid in controlling the aspect ratio of DSS joints,must be optimized to obtain desirable aspect ratio for DSS joints.Hence in this study,the above parameters of ATIG welding for aspect ratio of ASTM/UNS S32205 DSS welds are optimized by using Taguchi orthogonal array(OA)experimental design and other statistical tools such as Analysis of Variance(ANOVA) and Pooled ANOVA techniques.The optimum process parameters are found to be 1 mm electrode gap,130 mm/min travel speed,140 A current and 12 V voltage.The aspect ratio and the ferrite content for the DSS joints fabricated using the optimized ATIG parameters are found to be well within the acceptable range and there is no macroscopically evident solidification cracking.

The Full-Duplex Artificial Noise Scheme for Security of a Cellular System

This paper focuses on the problem of secure transmission in a cellular system. A full-duplex base station using artificial noise is adopted to improve both the uplink and downlink secrecy rate via pairing terminals which reverses the downlink and uplink of each other. We give the designs of artificial noise and the user's desired signal, and derive the pairing prin-ciple between terminals. Moreover, the influence of self-interference cancellation on secrecy rate is ex-plored. Simulation results show that the secrecy rate can get much better performance by adopting full-duplex artificial noise scheme and proposed pair-ing method. The downlink secrecy rate decreases with the distance between terminals. Besides the uplink secrecy rate is sensitive to the ability of self-interference cancellation.

Tooth surface geometry optimization of spiral bevel and hypoid gears generated by duplex helical method with circular profile blade

In order to effectively improve meshing performance of spiral bevel and hypoid gears generated by the duplex helical method, the effects of straight lined and circular cutting edges profile on meshing and contact of spiral bevel and hypoid gears were investigated analytically. Firstly, a mathematical model of spiral bevel and hypoid gears with circular blade profile was established according to the cutting characteristics of the duplex helical method. Based on a hypoid gear drive, the tooth bearings and the functions of transmission errors of four design cases were analyzed respectively by the use of the tooth contact analysis(TCA), and the contact stresses of the four design cases were analyzed and compared using simulation software. Finally, the curvature radius of the circular profile blade was optimized. The results show that the contact stresses are availably reduced, and the areas of edge contact and severe contact stresses can be avoided by selecting appropriate circular blade profile. In addition, the convex and concave sides are separately modified by the use of different curvature radii of inside and outside blades, which can increase the flexibility of the duplex helical method.

Mechanism of hot-rolling crack formation in lean duplex stainless steel 2101

The thermoplasticity of duplex stainless steel 2205（DSS2205） is better than that of lean duplex steel 2101（LDX2101）, which undergoes severe cracking during hot rolling. The microstructure, microhardness, phase ratio, and recrystallization dependence of the deformation compatibility of LDX2101 and DSS2205 were investigated using optical microscopy（OM）, electron backscatter diffraction（EBSD）, Thermo-Calc software, and transmission electron microscopy（TEM）. The results showed that the phase-ratio transformations of LDX2101 and DSS2205 were almost equal under the condition of increasing solution temperature. Thus, the phase transformation was not the main cause for the hot plasticity difference of these two steels. The grain size of LDX2101 was substantially greater than that of DSS2205, and the microhardness difference of LDX2101 was larger than that of DSS2205. This difference hinders the transfer of strain from ferrite to austenite. In the rolling process, the ferrite grains of LDX2101 underwent continuous softening and were substantially refined. However, although little recrystallization occurred at the boundaries of austenite, serious deformation accumulated in the interior of austenite, leading to a substantial increase in hardness. The main cause of crack formation is the microhardness difference between ferrite and austenite.

Effect of Heat Sink and Cooling Mediums on Ferrite Austenite Ratio and Distortion in Laser Welding of Duplex Stainless Steel 2205

In order to control the ferrite and austenite percentage in duplex stainless steel welding, many researchers try to change the laser welding parameters and cooling medium, but ignore to study the influence of heat sink effect on weld strength. In this work, the effect of aluminium heat sink and varying cooling medium on the laser welding of duplex stainless steel (DSS) 2205 is studied. The 2 mm thick DSS sheets welded with pulsed Nd: YAG laser welding machine by varying the cooling medium (air and oil) and an aluminium plate used as a heat sink. The welded specimens tested for tensile strength, micro-hardness, distortion, microstructure and radiography analysis. The faster cooling rate in the oil quenching process enhances the ferrite percentage compared with air-cooled samples. But the faster cooling rate in oil quenching leads to more distortion and using aluminium as a heat sink influenced positively the distortion to a small extent. The lower cooling rate in air quenching leads to a higher tensile strength of the welded specimen. The objective of this work is to analyse experimentally the effect of cooling medium and heat sink in the mechanical and metallurgical properties of laser welded duplex stainless steel.

Influence of hot rolling on the microstructure of lean duplex stainless steel 2101

In this work, the microstructure and the strain partitioning of lean duplex stainless steel 2101 (LDX 2101) during different hot-rolling processes are investigated by optical microscopy and electron-backscattered diffraction (EBSD). The results show that the LDX 2101 exhibits poor thermoplasticity at high temperature. The four-pass hot-rolled plates show fewer edge-cracking defects and superior thermoplasticity compared with the two-pass hot-rolled plates prepared at different temperature. The phase boundary is the weakest site in the LDX 2101. The cracks are initiated and propagated along the phase boundaries during the hot-rolling process. According to the EBSD analysis, the increase of the hot-rolling pass can dramatically improve the strain distribution in ferrite and austenite phases and promote the strain transmission in the constituent phases, thereby improving the coordinated deformation ability of the two phases. This effect further in- creases the thermoplasticity and reduces the formation of edge cracks in LDX 2101.

Endometriosis of the duplex appendix: A case report and review of the literature

BACKGROUND Duplication of the appendix is an infrequent congenital malformation with a complex classification.The horseshoe appendix is a subtype of the duplex appendix and is rarely reported in the literature.Endometriosis is a common gynecological disease that rarely occurs in the appendix.Moreover,horseshoe appendix combined with endometriosis has not been previously reported.CASE SUMMARY Here,we describe a 44-year-old woman who was admitted with a 1-d history of migratory lower right quadrant pain.Physical examination was consistent with the signs of acute appendicitis.The patient underwent an emergency exploratory laparotomy.The distal tip of the appendix was in contact with the cecum by another base,or“horseshoe appendix”.In addition,a small intestinal mass and an ovarian mass were identified.Subsequently,appendectomy,partial resection of the small intestine,and right oophorectomy were successively performed.The histopathology confirmed the diagnosis of acute inflammation of the duplex appendix with endometriosis,small intestine endometriosis,and ovarian endometriosis.CONCLUSION Surgeons need to be aware of the possibility of the duplex appendix when performing an appendectomy,and this study emphasizes the importance of exploring the entire abdomen.