Dynamic mechanical characteristics of frozen subgrade soil subjected to freeze-thaw cycles

As a widely-applied engineering material in cold regions, the frozen subgrade soils are usually subjected to seismic loading, which are also dramatically influenced by the freeze-thaw(F-T)cycles due to the varying temperature. A series of dynamic cyclic triaxial experiments were conducted through a cryogenic triaxial apparatus for exploring the influences of F-T cycles on the dynamic mechanical properties of frozen subgrade clay.According to the experimental results of frozen clay at the temperature of-10℃, the dynamic responses and microstructure variation at different times of F-T cycles(0, 1, 5, and 20 cycles) were explored in detail.It is experimentally demonstrated that the dynamic stress-strain curves and dynamic volumetric strain curves of frozen clay are significantly sparse after 20F-T cycles. Meanwhile, the cyclic number at failure(Nf) of the frozen specimen reduces by 89% after 20freeze-thaw cycles at a low ratio of the dynamic stress amplitude. In addition, with the increasing F-T cycles,the axial accumulative strain, residual deformation,and the value of damage variable of frozen clay increase, while the dynamic resilient modulus and dynamic strength decrease. Finally, the influence of the F-T cycles on the failure mechanisms of frozen clay was discussed in terms of the microstructure variation. These studies contribute to a better understanding of the fundamental changes in the dynamic mechanical of frozen soils exposed to F-T cycles in cold and seismic regions.

Optimal design and dynamic impact tests of removable bollards

Anti-ram bollard systems, which are installed around buildings and infrastructure, can prevent unauthorized vehicles from entering, maintain distance from vehicle-borne improvised explosive devices （VBIED） and reduce the corresponding damage. Compared with a fixed bollard system, a removable bollard system provides more flexibility as it can be removed when needed. This paper first proposes a new type of K4-rated removable anti-ram bollard system. To simulate the collision of a vehicle hitting the bollard system, a finite element model was then built and verified through comparison of numerical simulation results and existing experimental results. Based on the orthogonal design method, the factors influencing the safety and economy of this proposed system were examined and sorted according to their importance. An optimal design scheme was then produced. Finally, to validate the effectiveness of the proposed design scheme, four dynamic impact tests, including two front impact tests and two side impact tests, have been conducted according to BSI Specifications. The residual rotation angles of the specimen are smaller than 30~ and satisfy the requirements of the BSI Specification.

Analysis of volatile organic compounds emitted from aircraft carpets:comparison using headspace and dynamic chamber tests

Volatile organic compounds(VOCs) emitted from three types of carpets used in aircrafts were compared by using headspace and dynamic chamber tests. The headspace samples contained many compounds that were not detected in the dynamic chamber test; in addition, the dominant VOCs found by these two methods were different. The findings indicate that for highly sorptive materials such as carpets, headspace analysis may give inaccurate indication of actual VOC emissions, and it is necessary to conduct dynamic chamber tests over a certain period of time in order to identify the true emission characteristics. From the dynamic chamber tests, 2-ethyl-1-hexanol was the main VOC emitted from all three carpets. The study also examined the emission characteristics of aircraft carpets. In all experiments, total VOC(TVOC) concentration peaked within a few hours after the start of the experiment and was followed by rapid decay. The emission parameters of TVOC emitted by all three carpets were calculated and the simulated data matched the measured data well.

Application of computational fluid dynamics in design of viscous dampers-CFD modeling and full-scale dynamic testing

Computational fluid dynamics(CFD)provides a powerful tool for investigating complicated fluid flows.This paper aims to study the applicability of CFD in the preliminary design of linear and nonlinear fluid viscous dampers.Two fluid viscous dampers were designed based on CFD models.The first device was a linear viscous damper with straight orifices.The second was a nonlinear viscous damper containing a one-way pressure-responsive valve inside its orifices.Both dampers were detailed based on CFD simulations,and their internal fluid flows were investigated.Full-scale specimens of both dampers were manufactured and tested under dynamic loads.According to the tests results,both dampers demonstrate stable cyclic behaviors,and as expected,the nonlinear damper generally tends to dissipate more energy compared to its linear counterpart.Good compatibility was achieved between the experimentally measured damper force-velocity curves and those estimated from CFD analyses.Using a thermography camera,a rise in temperature of the dampers was measured during the tests.It was found that output force of the manufactured devices was virtually independent of temperature even during long duration loadings.Accordingly,temperature dependence can be ignored in CFD models,because a reliable temperature compensator mechanism was used(or intended to be used)by the damper manufacturer.

Effects of dynamic flow rates on degradation deposition behavior of Mg scaffold

Degradability of bone tissue engineering scaffold that matching the regeneration rate could allow a complete replacement of host tissue.However,the porous structure of biodegradable Mg scaffolds certainly generated high specific surface area,and the three-dimensional interconnected pores provided fast pervasive invasion entrance for the corrosive medium,rising concern of the structural integrity during the degradation.To clarify the structural evolution of the three-dimensional(3D)porous structure,semi-static immersion tests were carried out to evaluate the degradation performance in our previous study.Nevertheless,dynamic immersion tests mimicking the in vivo circulatory fluid through the interconnected porous structure have yet been investigated.Moreover,the effects of dynamic flow rates on the degradation deposition behavior of 3D porous Mg scaffolds were rarely reported.In this study,Mg scaffolds degraded at three flow rates exhibited different degradation rates and deposition process.A flow rate of 0.5 m L/min introduced maximum drop of porosity by accumulated deposition products.The deposition products provided limited protection against the degradation process at a flow rate of 1.0 m L/min.The three-dimensional interconnected porous structure of Mg scaffold degraded at 2.0 m L/min well retained after 14 days showing the best interconnectivity resistance to the degradation deposition process.The dynamic immersion tests disclosed the reason for the different degradation rates on account of flow rates,which may bring insight into understanding of varied in vivo degradation rates related to implantation sites.

Dynamic Testing of Elastic Modulus,Shear Modulus,and Poisson’s Ratio of Bamboo Scrimber

The bamboo scrimber is an anisotropic material.The elastic constant values of the bamboo scrimber specimens measured by the dynamic and static methods are consistent,and the dynamic test method has the advantages of rapidity,simplicity,good repeatability,and high precision.Bamboo scrimber has strong potential as a building material,and its elastic constant is an important index to measure its mechanical properties.To quickly,simply,non-destructively,and accurately detect the elastic constant of the bamboo scrimber,they were dynamically tested by the free plate transient excitation method and cantilever plate torsional vibration method.The static four-point bending method was used to verify the accuracy and reliability of the dynamic elastic modulus,shear modulus,and Poisson’s ratio of the bamboo scrimber.The mechanism analysis and evaluation of the quality grade,homogeneity,and size effect of the bamboo scrimber whole board were carried out.The main results show that the dynamic elastic modulus,shear modulus,and Poisson’s ratio of the bamboo scrimber are 12 GPa,1500 MPa,and 0.31,respectively,which meet the requirements of GB/T 40247-2021 for structural bamboo scrimber.

Correction of dynamic Brazilian disc tensile strength of rocks under preloading conditions considering the overload phenomenon and invoking the Griffith criterion

Dynamic tensile failure is a common phenomenon in deep rock practices,and thus accurately evaluating the dynamic tensile responses of rocks under triaxial pressures is of great significance.The Brazilian disc(BD)test is the suggested method by the International Society for Rock Mechanics and Rock Engineering(ISRM)for measuring both the static and dynamic tensile strengths of rock-like materials.However,due to the overload phenomenon and the complex preloading conditions,the dynamic tensile strengths of rocks measured by the BD tests tend to be overestimated.To address this issue,the dynamic BD tensile strength(BTS)of Fangshan marble(FM)under different preloading conditions were measured through a triaxial split Hopkinson pressure bar(SHPB).The fracture onset in BD specimen was captured through a strain gage around the disc center.The discrepancy between the traditional tensile strength(TTS,determined by the peak load P_(f) of the BD specimen)and the nominal tensile strength(NTS,obtained from the load P_(i) when the diametral fracture commences in the tested BD specimen)was applied to quantitatively evaluating the overload phenomenon.The Griffith criterion was used to rectify the calculation of the tensile stress at the disc center under triaxial stress states.The results demonstrate that the overload ratio(s)increases with the loading rate(σ)and decreases with the hydrostatic pressure(σ_(s)).The TTS corrected by the Griffith criterion is independent of theσ_(s)due to the overload phenomenon,while the NTS corrected by the Griffith criterion is sensitive to both the andσ.Therefore,it is essential to modify the tensile stress in dynamic confined BD tests using both the overload correction and the Griffith criterion rectification to obtain the accurate dynamic BTS of rocks.

Research on damage failure mechanism and dynamic mechanical behavior of layered shale with different angles under confining pressure

The hydrostatic or confining pressure of deep rocks has a significant impact on the mechanical behavior of brittle materials.Especially when confining pressure is applied,the mechanical properties of rock materials will undergo significant changes.Considering that the process of shale sample subjected to impact load is in a closed container in the dynamic triaxial SHPB test,the failure process of the sample cannot be observed.Meanwhile,the activation volume of the shale sample would be large and local failure would occur in the test under the high strain rate loading.Therefore,thefinite element model of shale considering the bedding effect under confining pressure was established in this study.Taking shale materials with different bedding dip angles as simulation objects,the dynamic failure characteristics of shale were studied using the dynamic analysis software ANSYS/LS‐DYNA from three aspects:stress‐strain curve,failure growth process,and failure morphology.The research results obtained can serve as the key technical parameters for deep resource extraction.

Networked collaborative pseudo-dynamic testing of a multi-span bridge based on NetSLab

Modem dynamic tests such as networked collaborative pseudo-dynamic testing （PDT） provide new tools to study the dynamic performance of large and complex structures. In this paper, several networked collaborative PDT systems established in China and abroad are introduced, including a detailed description of the first networked collaborative platform that involved the construction of a standardized demonstration procedure for networked collaborative PDT. The example is a multi-span bridge with RC piers retrofitted by FRP, and a networked structural laboratory （NetSLab） platform is used to link distributed laboratories located at several universities together. Substructure technology is also used in the testing. The characteristics, resource sharing and collaborative work of NetSLab are described, and the results illustrate that use of the NetSLab is feasible for studying the dynamic performance of multi-span bridge structures.

Energy-based dynamic parameter identification for Pasternak foundation model

Parameter identification of Pasternak foundation models(PFM)is never satisfactory,which discourages the application and popularization of PFM.In the present study,an energy-based model to predict the dynamic foundation coefficients was proposed using the vibration kinetic energy and potential energy of a Pasternak foundation-rigid plate system.On the basis of the Pasternak foundation,the relationship among the natural frequency,dynamic foundation coefficients,rigid plate configuration,and vibrating soil equivalent mass per unit area was considered.To obtain the natural frequencies of the Pasternak foundation-rigid plate system,dynamic tests were performed.Using two or more dynamic test results of various rigid plates on a foundation,a set of equations of dynamic foundation coefficients was set up to directly identify the foundation coefficients and equivalent mass per unit area of vibrating soil.The feasibility of the proposed method was verified by comparing it with the outdoor and indoor test results and finite element analysis results.When the proposed method is used to obtain the dynamic parameters,PFM can be generalized and applied more widely in engineering practice.

Delay-dependent stability and added damping of SDOF real-time dynamic hybrid testing

It is well-recognized that a transfer system response delay that reduces the test stability inevitably exists in real-time dynamic hybrid testing （RTDHT）. This paper focuses on the delay-dependent stability and added damping of SDOF systems in RTDHT. The exponential delay term is transferred into a rational fraction by the Pad6 approximation, and the delay-dependent stability conditions and instability mechanism of SDOF RTDHT systems are investigated by the root locus technique. First, the stability conditions are discussed separately for the cases of stiffness, mass, and damping experimental substructure. The use of root locus plots shows that the added damping effect and instability mechanism for mass are different from those for stiffness. For the stiffness experimental substructure case, the instability results from the inherent mode because of an obvious negative damping effect of the delay. For the mass case, the delay introduces an equivalent positive damping into the inherent mode, and instability occurs at an added high frequency mode. Then, the compound stability condition is investigated for a general case and the results show that the mass ratio may have both upper and lower limits to remain stable. Finally, a high-emulational virtual shaking table model is built to validate the stability conclusions.

Mechanical properties of rock under coupled static-dynamic loads

Rock drilling machine,INSTRON testing system,and SHPB device are updated to investigate the characteristics of rocks at great depth,with high loads from overburden,tectonic stresses and dynamic impacts due to blasting and boring.It is verified that these testing systems can be used to study the mechanical properties of rock material under coupled static and dynamic loading condition and give useful guidance for the deep mining and underground cavern excavation.Various tests to determine the rock strength,fragmentation behavior,and energy absorption were conducted using the updated testing systems.It is shown that under coupled static-dynamic loads,if the axial prestress is lower than its elastic limit,the rock strength is higher than the individual static or dynamic strength.At the same axial prestress,rock strength under coupled loads rises with the increasing strain rates.Under coupled static and dynamic loads,rock is observed to fail with tensile mode.While shear failure may exist if axial prestress is high enough.In addition,it is shown that the percentage of small particles increases with the increasing axial prestress and impact load based on the analysis of the particle-size distribution of fragments.It is also suggested that the energy absorption ratio of a specimen varies with coupled loads,and the maximum energy absorption ratio for a rock can be obtained with an appropriate combination of static and dynamic loads.

Dynamic mechanical characteristics and application of constant resistance energy-absorbing supporting material

In deep underground engineering,rock burst and other dynamic disasters are prone to occur due to stress concentration and energy accumulation in surrounding rock.The control of dynamic disasters requires bolts and cables with high strength,high elongation,and high energy-absorbing capacity.Therefore,a constant resistance energy-absorbing(CREA)material is developed.In this study,the dynamic characteristics of the new material are obtained via the drop hammer tests and the Split Hopkinson Pressure Bar(SHPB)tests of the new material and two common bolt(CB)materials widely used in the field.The test results of drop hammer test and SHPB test show that the percentage elongation of CREA material is more than 2.64 and 3.22 times those of the CB material,and the total impact energy acting on CREA material is more than 18.50 and 21.84 times,respectively,indicating that the new material has high elongation and high energy-absorbing capacity.Subsequently,the CREA bolts and cables using the new material are developed,which are applied in roadways with high stress and strong dynamic disturbance.The field monitoring results show that CREA bolts and cables can effectively control the surrounding rock deformation and ensure engineering safety.

Simulation of large-scale numerical substructure in real-time dynamic hybrid testing

A solution scheme is proposed in this paper for an existing RTDHT system to simulate large-scale finite element （FE） numerical substructures. The analysis of the FE numerical substructure is split into response analysis and signal generation tasks, and executed in two different target computers in real-time. One target computer implements the response analysis task, wherein a large time-step is used to solve the FE substructure, and another target computer implements the signal generation task, wherein an interpolation program is used to generate control signals in a small time-step to meet the input demand of the controller. By using this strategy, the scale of the FE numerical substructure simulation may be increased significantly. The proposed scheme is initially verified by two FE numerical substructure models with 98 and 1240 degrees of freedom （DOFs）. Thereafter, RTDHTs of a single frame-foundation structure are implemented where the foundation, considered as the numerical substructure, is simulated by the FE model with 1240 DOFs. Good agreements between the results of the RTDHT and those from the FE analysis in ABAQUS are obtained.

Effect of Temperature and Strain Rate on Dynamic Properties of Low Silicon TRIP Steel

The dynamic tensile test of 0.11C-0.62Si-1.65Mn TRIP steel was carried out at different strain rates and test temperatures. The results show that both temperature and strain rate affect the retained austenite transformation. At high strain rates, the uniform elongation decreases, whereas the total elongation and energy absorption increase. The tensile strength is less strain rate sensitive. With raising test temperature, the tensile strength is reduced and the mechanical properties generally deteriorate, especially at 110℃,However, excellent mechanical properties were obtained at 50℃ and 75℃.

Dynamic Elastic Modulus and Damping Ratio of Lignin-Modified Loess

To effectively improve the poor engineering properties of loess and enhance its seismic performance,the industrial by-product lignin is used as a modified material.Based on lots of dynamic triaxial tests,the dynamic elastic modulus and damping ratio of lignin-modified loess were tested.The effects of lignin content on the dynamic elastic modulus and damping ratio of lignin-modified loess were analyzed.Combined with scanning electron microscopy(SEM)and X-ray diffraction(XRD),the microscopic mechanism of lignin to improve the dynamic properties of loess was studied.The results show that lignin can effectively modify the dynamic deformation of loess under dynamic load.Under the same dynamic stress condition,the dynamic strain of lignin-modified loess is smaller than compacted loess.The dynamic elastic modulus of modified loess with different lignin content are quite different,but both decrease with the increase of dynamic strain.And the dynamic elastic modulus of modified loess is greater than compacted loess.The maximum dynamic elastic modulus of modified loess with a lignin content of 1%are significantly greater than others.Under the same dynamic strain condition,the damping ratio of lignin-modified loess is smaller than compacted loess.Lignin can effectively fill loess pores and cement loess particles.Compared with compacted loess,no new mineral components are generated in the lignin-modified loess.The optimum lignin content of dynamics characteristic of modified loess is present,and the optimum lignin content is 1%.

Experimental Study on Common and Steel Fiber Reinforced Concrete Under Dynamic Tensile Stress

Split Hopkinson technique has been developed to test the strength of common concrete and steel fiber reinforced concrete under dynamic tensile stress. Two types of test methods are considered, the splitting tensile test and a modified spalling test in which a specimen is loaded under uniaxial stress. The result shows that the dynamic strength enhancement of concrete is remarkable by using the reinforcing fiber. But for the common concrete, the base of compressive strength seems to show little effect on the tensile strength under dynamic loading. The experimental results also show that the resistance to tensile fracture of the steel fiber reinforced concrete for C100-mix is higher than those of C40-mix..

Applications of dynamic visual acuity test in clinical ophthalmology

Dynamic visual acuity test(DVAT)plays a key role in the assessment of vestibular function,the visual function of athletes,as well as various ocular diseases.As the visual pathways conducting dynamic and static signals are different,DVATs may have potential advantages over the traditional visual acuity tests commonly used,such as static visual acuity,contrast sensitivity,and static perimetry.Here,we provide a review of commonly applied DVATs and their several uses in clinical ophthalmology.These data indicate that the DVAT has its unique clinical significance in the evaluation of several ocular disorders.

Optimization of dynamic sequential test strategy for equipment health management

Testing is the premise and foundation of realizing equipment health management （EHM）. To address the problem that the static periodic test strategy may cause deficient test or excessive test, a dynamic sequential test strategy （DSTS） for EHM is presented. Considering the situation that equipment health state is not completely observable in reality, a DSTS optimization method based on partially observable semi-Markov decision pro- cess （POSMDP） is proposed. Firstly, an equipment health state degradation model is constructed by Markov process, and the control limit maintenance policy is also introduced. Secondly, POSMDP is formulated in great detail. And then, POSMDP is converted to completely observable belief semi-Markov decision process （BSMDP） through belief state. The optimal equation and the corresponding optimal DSTS, which minimize the long-run ex- pected average cost per unit time, are obtained with BSMDP. The results of application in complex equipment show that the proposed DSTS is feasible and effective.

Performance of identical rockbolts tested on four dynamic testing rigs employing the direct impact method

Impact drop tests are routinely used to examine the dynamic performance of rockbolts.Numerous impact tests have been carried out in the past decades on independently designed,constructed and operated testing rigs.Each laboratory has developed testing procedures;thus,the results are often reported in different ways by various laboratories.The inconsistency in testing procedures and reporting formats presents a challenge when comparing results from different laboratories.A series of impact tests of identical rockbolts was carried out using the direct impact method(i.e.the mass free-fall method)on the rigs in four laboratories in different countries.The purpose of these tests was to investigate the level of consistency in the results from the four rigs.Each rig demonstrated a high level of repeatability,but differences existed between the various rigs.The differences would suggest that there is noticeable equipment-dependent bias when test results obtained from different laboratories are compared.It was also observed that the energy dissipated for the plastic displacement of the bolt was smaller than the impact energy in the tests.The average impact load(AIL)and the ultimate plastic displacement(D)of the bolt describe the ultimate dynamic performance of the bolt.In the case where the bolt does not rupture,the specific plastic energy(SPE)is an appropriate parameter in describing the impact performance of the bolt.Two other relevant parameters are the first peak load(FPL)and the initial stiffness(K)of the bolt sample.The information from this test series will guide the formulation of standardised testing procedures for dynamic impact tests of rockbolts.