This paper sums up the determining analysis of the measuring location of Treflusing a thermocouple during the thermography tests.Laboratory temperature distribution testing methods,analysis of value and location of Tre...This paper sums up the determining analysis of the measuring location of Treflusing a thermocouple during the thermography tests.Laboratory temperature distribution testing methods,analysis of value and location of Treflmeasurement are explained in this paper.The heat source is two halogen lamps of 500 watts eachfitted at a distance of 30–50 cm.Noises appearing during testing of thermography are corrected with measured T_(refl) value.The results of thermogram correction of corroded concrete surfaces using T_(refl) values are displayed in this paper too.The concrete surface temperature results of quantitative image processing method are compared to the experimental test results.The results showed good accuracy,which was seen from most errors<3%and the maximum error is<5%.The end of paper,explained of application Treflvalue to the corroded reinforced concrete thermogram.展开更多
To identify refl ector fractures near borehole by using dipole-source refl ected-shearwave logging, we need to understand the relation between the amplitude of the refl ected shear wave and the source radiation, boreh...To identify refl ector fractures near borehole by using dipole-source refl ected-shearwave logging, we need to understand the relation between the amplitude of the refl ected shear wave and the source radiation, borehole conditions, and attenuation owing to the surrounding formations. To assess the effect of these factors on the amplitude of the refl ected waves, we first studied the radiation performance and radiation direction of the dipole source in fast, medium, and slow formations by using the asymptotic solution in the far fi eld of the borehole. Then, the relation between the fracture parameters, and the refl ected-shear-wave amplitude as well as the ratio of the refl ected-shear-wave amplitude to the direct-wave amplitude (relative amplitude, RA) was evaluated by the three-dimensional fi nite-difference (3D FDTD) method. Finally, the fracture detection capability of the dipole reflected-shear-wave logging tool in different formations was analyzed by using the RA. The results suggest that the radiation amplitude of the SH-wave in the slow formation is weaker than those in the fast and medium formations, and the amplitude of the refl ected shear wave is lower. However, the RA in the slow formation is close to or even greater than in the fast and medium formations, which means that dipole-source shear-wave logging has the same or even better fracture detection capability in the slow formation as in the fast and medium formations. In addition, when RA is small, there is a good correlation between the RA and the various fracture parameters in the different types of formation, which can be used in determining the lower limit of the fracture parameters identifi ed by refl ection logging.展开更多
Electrocatalytic glucose oxidation reaction(GOR)has attracted much attention owing to its crucial role in biofuel cell fabrication.Herein,we load MoO_(3)nanoparticles on carbon nanotubes(CNTs)and use a discharge proce...Electrocatalytic glucose oxidation reaction(GOR)has attracted much attention owing to its crucial role in biofuel cell fabrication.Herein,we load MoO_(3)nanoparticles on carbon nanotubes(CNTs)and use a discharge process to prepare a noblemetal-free MC-60 catalyst containing MoO_(3),Mo_(2)C,and a Mo_(2)C–MoO_(3)interface.In the GOR,MC-60 shows activity as high as 745μA/(mmol/L cm^(2)),considerably higher than those of the Pt/CNT(270μA/(mmol/L cm^(2)))and Au/CNT catalysts(110μA/(mmol/L cm^(2))).In the GOR,the response minimum on MC-60 is as low as 8μmol/L,with a steady-state response time of only 3 s.Moreover,MC-60 has superior stability and anti-interference ability to impurities in the GOR.The better performance of MC-60 in the GOR is attributed to the abundant Mo sites bonding to C and O atoms at the MoO_(3)–Mo_(2)C interface.These Mo sites create active sites for promoting glucose adsorption and oxidation,enhancing MC-60 performance in the GOR.Thus,these results help to fabricate more effi cient noble-metal-free catalysts for the fabrication of glucose-based biofuel cells.展开更多
Recent studies have highlighted the increase in treatment resistant depression. Of particular concern is the rising trend of depression and suicide rates among Young Adults. Ketamine was approved for treatment resista...Recent studies have highlighted the increase in treatment resistant depression. Of particular concern is the rising trend of depression and suicide rates among Young Adults. Ketamine was approved for treatment resistant depression in 2019 by the US Food and Drug Administration. It received an additional indication for treatment of suicidality. While intranasal Ketamine is approved for depression, recent data about intravenous infusion of Ketamine in controlled inpatient settings has been promising. ECT has a long-standing trend for being used for resistant depression and recent comparison trials have revealed positive results when head-to-head comparisons are made with Ketamine. Future studies need to focus on patient selection and wherein treatment algorithm should Ketamine be selected as treatment modality.展开更多
Electrical capacitance tomography （ECT） is a promising technique for multi-phase flow measurement due to its high speed, low cost and non-intrusive sensing. Image reconstruction for ECT is an inverse problem of find...Electrical capacitance tomography （ECT） is a promising technique for multi-phase flow measurement due to its high speed, low cost and non-intrusive sensing. Image reconstruction for ECT is an inverse problem of finding the permittivity distribution of an object by measuring the electrical capacitances between sets of electrodes placed around its periphery. The conjugate gradient （CG） method is a popular image reconstruction method for ECT, in spite of its low convergence rate. In this paper, an advanced version of the CG method, the projected CG method, is used for image reconstruction of an ECT system. The solution space is projected into the Kryiov subspace and the inverse problem is solved by the CG method in a low-dimensional specific subspace. Both static and dynamic experiments were carried out for gas-solid two-phase flows. The flow regimes are identified using the reconstructed images obtained with the projected CG method. The results obtained indicate that the projected CG method improves the quality of reconstructed images and dramatically reduces computation time, as compared to the traditional sensitivity, Landweber, and CG methods. Furthermore, the projected CG method was also used to estimate the important parameters of the pneumatic conveying process, such as the volume concentration, flow velocity and mass flow rate of the solid phase. Therefore, the projected CG method is considered suitable for online gas-solid two-phase flow measurement,展开更多
基金This research was supported by the P3MI Research Grants.Thanks to Prof.Herlien D Setio as authors who received the grant.
文摘This paper sums up the determining analysis of the measuring location of Treflusing a thermocouple during the thermography tests.Laboratory temperature distribution testing methods,analysis of value and location of Treflmeasurement are explained in this paper.The heat source is two halogen lamps of 500 watts eachfitted at a distance of 30–50 cm.Noises appearing during testing of thermography are corrected with measured T_(refl) value.The results of thermogram correction of corroded concrete surfaces using T_(refl) values are displayed in this paper too.The concrete surface temperature results of quantitative image processing method are compared to the experimental test results.The results showed good accuracy,which was seen from most errors<3%and the maximum error is<5%.The end of paper,explained of application Treflvalue to the corroded reinforced concrete thermogram.
基金supported by the National Petroleum Major Projects(No.2017ZX05019-005)CNPC Fundamental Research Projects(No.2016A-3605)
文摘To identify refl ector fractures near borehole by using dipole-source refl ected-shearwave logging, we need to understand the relation between the amplitude of the refl ected shear wave and the source radiation, borehole conditions, and attenuation owing to the surrounding formations. To assess the effect of these factors on the amplitude of the refl ected waves, we first studied the radiation performance and radiation direction of the dipole source in fast, medium, and slow formations by using the asymptotic solution in the far fi eld of the borehole. Then, the relation between the fracture parameters, and the refl ected-shear-wave amplitude as well as the ratio of the refl ected-shear-wave amplitude to the direct-wave amplitude (relative amplitude, RA) was evaluated by the three-dimensional fi nite-difference (3D FDTD) method. Finally, the fracture detection capability of the dipole reflected-shear-wave logging tool in different formations was analyzed by using the RA. The results suggest that the radiation amplitude of the SH-wave in the slow formation is weaker than those in the fast and medium formations, and the amplitude of the refl ected shear wave is lower. However, the RA in the slow formation is close to or even greater than in the fast and medium formations, which means that dipole-source shear-wave logging has the same or even better fracture detection capability in the slow formation as in the fast and medium formations. In addition, when RA is small, there is a good correlation between the RA and the various fracture parameters in the different types of formation, which can be used in determining the lower limit of the fracture parameters identifi ed by refl ection logging.
基金supported by the National Natural Science Foundation of China(Nos.82170426 and 22078193)Double Thousand Plan of Jiangxi Province(Nos.461654,jxsq2019102052).
文摘Electrocatalytic glucose oxidation reaction(GOR)has attracted much attention owing to its crucial role in biofuel cell fabrication.Herein,we load MoO_(3)nanoparticles on carbon nanotubes(CNTs)and use a discharge process to prepare a noblemetal-free MC-60 catalyst containing MoO_(3),Mo_(2)C,and a Mo_(2)C–MoO_(3)interface.In the GOR,MC-60 shows activity as high as 745μA/(mmol/L cm^(2)),considerably higher than those of the Pt/CNT(270μA/(mmol/L cm^(2)))and Au/CNT catalysts(110μA/(mmol/L cm^(2))).In the GOR,the response minimum on MC-60 is as low as 8μmol/L,with a steady-state response time of only 3 s.Moreover,MC-60 has superior stability and anti-interference ability to impurities in the GOR.The better performance of MC-60 in the GOR is attributed to the abundant Mo sites bonding to C and O atoms at the MoO_(3)–Mo_(2)C interface.These Mo sites create active sites for promoting glucose adsorption and oxidation,enhancing MC-60 performance in the GOR.Thus,these results help to fabricate more effi cient noble-metal-free catalysts for the fabrication of glucose-based biofuel cells.
文摘Recent studies have highlighted the increase in treatment resistant depression. Of particular concern is the rising trend of depression and suicide rates among Young Adults. Ketamine was approved for treatment resistant depression in 2019 by the US Food and Drug Administration. It received an additional indication for treatment of suicidality. While intranasal Ketamine is approved for depression, recent data about intravenous infusion of Ketamine in controlled inpatient settings has been promising. ECT has a long-standing trend for being used for resistant depression and recent comparison trials have revealed positive results when head-to-head comparisons are made with Ketamine. Future studies need to focus on patient selection and wherein treatment algorithm should Ketamine be selected as treatment modality.
基金support from the National Natural Science Foundation of China(50937005,61001135,61201350)the Natural Science Foundation of Tianjin Municipal Science and Technology Commission(11JCYBJC06900)
文摘Electrical capacitance tomography （ECT） is a promising technique for multi-phase flow measurement due to its high speed, low cost and non-intrusive sensing. Image reconstruction for ECT is an inverse problem of finding the permittivity distribution of an object by measuring the electrical capacitances between sets of electrodes placed around its periphery. The conjugate gradient （CG） method is a popular image reconstruction method for ECT, in spite of its low convergence rate. In this paper, an advanced version of the CG method, the projected CG method, is used for image reconstruction of an ECT system. The solution space is projected into the Kryiov subspace and the inverse problem is solved by the CG method in a low-dimensional specific subspace. Both static and dynamic experiments were carried out for gas-solid two-phase flows. The flow regimes are identified using the reconstructed images obtained with the projected CG method. The results obtained indicate that the projected CG method improves the quality of reconstructed images and dramatically reduces computation time, as compared to the traditional sensitivity, Landweber, and CG methods. Furthermore, the projected CG method was also used to estimate the important parameters of the pneumatic conveying process, such as the volume concentration, flow velocity and mass flow rate of the solid phase. Therefore, the projected CG method is considered suitable for online gas-solid two-phase flow measurement,
