Review of emulsified asphalt modification mechanisms and performance influencing factors

In recent years,with the improvement of the requirements of road performance,modified emulsified asphalts with better performance has gradually replaced the emulsified asphalt and become the primary material for road maintenance.This paper introduces the modified emulsified asphalt materials commonly used in pavement maintenance projects,definitions and modified mechanisms of polymerized styrene butadiene rubber(SBR)modified emulsified asphalt,styrene butadiene styrene block polymer(SBS)modified emulsified asphalt and waterborne epoxy resin(WER)modified emulsified asphalt are summarized.The analysis focused on comparing the effects of modifiers,preparation process,auxiliary additives,and other factors on the performance of modified emulsified asphalt.In this paper,it is considered that the greatest impact on the performance of emulsified asphalt is the modifier,emulsifier mainly affects the speed of breaking the emulsion,stabilizers on the basic performance of emulsified asphalt evaporative residue is small;and when the modifier is distributed in the asphalt in a network,the dosage at this time is the recommended optimum dosage.Finally,this study recommends that in the future,the polymer-asphalt compatibility can be improved through composite modification,chemical grafting and other methods to continue to develop broader applicability and better performance of modified emulsified asphalt.

Effect of emulsified isoflurane on apoptosis of anoxia-reoxygenation neonatal rat cardiomyocytes

Objective:To explore the effect of emulsified isoflurane(EI)on apoptosis of anoxia-reoxygenation neonatal rat cardiomyocytea and relevant protein expression.Methods:Cardiac muscle anoxiareoxygenation damage model was established with culture in vitro neonatal rat cardiomyocytes.The cardiomyocytes were divided into control group,model group,fat emulsion group and EI group.The cardiomyocytes apoptosis rates and lactic dehydrogenase(LDH),superoxide dismutase(SOD)and malondialdehyde(MDA)index standardization were detected after relevant treatment The expression of apoptosis-related proteins Bel-2,Bax and Caspase-3 were detected with Western blot approach.Results:After hypoxia/reoxygenation(H/R)model was treated by EI,the cells apoptosis rate decreased and was dramatically below the fat emulsion group(P<0.05),Cardiomyocytes biochemical index detection presented that,compared with the control group that the LDH activity and MDA content dramatically increased(P<0.05),while the SOD activity notably decreased(P<0.05);compared with the H/R group,the SOD activity of the fat emulsion group and EI group increased(P<0.05);while the LDH activity and MDA content decreased(P<0.05).And the change of the EI group was more remarkable than the fat emulsion group(P<0.05).The Western blot analysis presented that,compared with the control group,the Bcl-2 protein expression of the other groups significantly decreased(P<0.05),the expressions of Bax protein and Caspase-3protein increased significantly(P<0.05);compared with H/R group,cardiomyocytes Bc1-2protein expression of EI group increased significantly(P<0.05),the expressions of Bax protein and Caspase-3 protein decreased significantly(P<0.05),and the change of EI group was more remarkable than the fat emulsion group(P<0.05).Conclusions:EI can inhabit the apoptosis of anoxia-reoxygenation damage model cardiomyocytes,and may he related to the up-regulation of expression of Bcl-2 and down-regulation of expression of Caspase-3 protein.

An appropriate level of autophagy reduces emulsified isoflurane-induced apoptosis in fetal neural stem cells

Autophagy plays essential roles in cell survival.However,the functions and regulation of the autophagy-related proteins Atg5,LC3B,and Beclin 1 during anesthetic-induced developmental neurotoxicity remain unclear.This study aimed to understand the autophagy pathways and mechanisms that affect neurotoxicity,induced by the anesthetic emulsified isoflurane,in rat fetal neural stem cells.Fetal neural stem cells were cultured,in vitro,and neurotoxicity was induced by emulsified isoflurane treatment.The effects of pretreatment with the autophagy inhibitors 3-methyladenine and bafilomycin and the effects of transfection with small interfering RNA against ATG5(siRNA-Atg5)were observed.Cell viability was determined using the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide assay,and apoptosis was assessed using flow cytometry.Ultrastructural changes were analyzed through transmission electron microscopy.The levels of the autophagy-related proteins LC3B,Beclin 1,Atg5,and P62 and the pro-apoptosis-related protein caspase-3 were analyzed using western blot assay.The inhibition of cell proliferation and that of apoptosis rate increased after treatment with emulsified isoflurane.Autophagolysosomes,monolayer membrane formation due to lysosomal degradation,were observed.The autophagy-related proteins LC3B,Beclin 1,Atg5,and P62 and caspase-3 were upregulated.These results confirm that emulsified isoflurane can induce toxicity and autophagy in fetal neural stem cells.Pre-treatment with 3-methyladenine and bafilomycin increased the apoptosis rate in emulsified isoflurane-treated fetal neural stem cells,which indicated that the complete inhibition of autophagy does not alleviate emulsified isoflurane-induced fetal neural stem cell toxicity.Atg5 expression was decreased significantly by siRNA-Atg5 transfection,and cell proliferation was inhibited.These results verify that the Atg5 autophagy pathway can be regulated to maintain appropriate levels of autophagy,which can inhibit the neurotoxicity induced by emulsified isoflurane anesthetic in fetal neural stem cells.

The Properties of Cement Mortars Modified by Emulsified Epoxy and Micro-fine Slag

The epoxy resin polymer cement mortars with excellent performances were made up through modifying ordinary Portland cement with emulsified epoxy and micro fine slag.The microstructure of the epoxy resin polymer cement materials was studied and their hydration and hardening characteristics were discussed by means of modern analysis measures such as SEM,XRD and Hg intrusion micromeritics.The experimental results indicate that the series effects of water reducing,density,pozzolanicity,filling and solidification crosslinking through the action together with epoxy organism and micro fine slag endowed cement based materials with perfect performances.The main hydration products in the system are C S H gel and hydrated calcium aluminate.At later age,AFt can be in existence,and no Ca(OH) 2 is found.When epoxy resin is solidified,the organism is in a network structure.In the micro pore structure of hydrated cement with modified epoxy and fine slag,big harmful pores were fewer,more harmless abundant micro pores were and the possible pore radius was smaller than that of ordinary Portland cement.

Hydrophobic and Magnetic Reduced Graphene Oxide Nanocomposite for Emulsified Oil Removal

Magnetic reduced graphene oxide(MRGO) nanocomposite was prepared by the chemical coprecipitation method and applied as adsorbent for removing emulsified oil from oily wastewater. SEM, TEM, XRD, FT-IR, VSM and other analytical methods were utilized to characterize the prepared MRGO. The adsorption performance of MRGO was evaluated under different initial adsorbate concentration, MRGO dosage, temperature, and pH value of the solution. The adsorption kinetics and isotherms were investigated. In addition, the MRGO repeatability was also tested. It was found that almost 65%of emulsified oil were removed by MRGO in the first 15 min. The MRGO adsorption capacity and efficiency for removal of adsorbate reached 335.85 mg/g and 92.52% within 60 min, respectively. The adsorption capacity reduced with an increasing MRGO dosage, while increased with the increase of emulsified oil concentration. The adsorption performance of MRGO in the alkaline environment was lower than that in the acidic environment. The adsorption data could well fit to the pseudosecondorder model. The Langmuir model could well describe the isotherm data. The MRGO adsorption capacity was still more than 236.1 mg/g at the sixth regeneration cycle.

Effect of Emulsified Diesel Fuel on Performance and Emissions Characteristics

Diesel fuel has been known as the most effective fuel but it is known as a fuel which produces harmful emissions. Later, emulsified diesel fuel was introduced as a better solution but there is no sufficient research data concerning combustion of emulsified fuel. The present work carried out a simulation of non-surfactant emulsified diesel fuel where composition of water in emulsion varied from 0% to 20% to determine the ratio of water to diesel which is more effective in reducing the exhaust emissions especially NOx. For this simulation,5% of water in diesel without surfactant was able to reduce NOx?up to 35%. It was shown that as the percentage of water increases, the power from that fuel combustion reduces.

Properties of Polyacrylate Latex Prepared Under Different Emulsified Systems

The polyacrylate latexes were synthesized via pre-emulsified and semi-continuous seeded emulsion polymerization technology when conventional surfactant or polymerizable surfactant was used as emulsifiers. The resultant latexes and their films were characterized with the contact angle determinator and rheometer. Effect of the polymerizable surfactant on water resistance, stability and rheology of the latex was studied. Results show that the water resistance of film is increased first then decreased with the increase of the amount of the polymerizable surfactant. There exists the optimum value of the amount of the polymerizable surfactant for the water resistance of the film. In comparison with the latex prepared with the conventional surfactant, both the mechanical stability and the freezing-thaw stability of the latex are improved when the polymerizable surfactant is used during the course of the emulsion polymerization. The resultant latex has rheological properties of pseudo-plastic fluid and belongs to non-Newtonian fluid.

Kinetics of nitrobenzene degradation coupled to indigenous microorganism dissimilatory iron reduction stimulated by emulsified vegetable oil

Widespread contamination by nitrobenzene（NB） in sediments and groundwater requires better understanding of the biogeochemical removal process of the pollutant. NB degradation, coupled with dissimilatory iron reduction, is one of the most efficient pollutant removal methods. However, research on NB degradation coupled to indigenous microorganism dissimilatory iron reduction stimulated by electron donors is still experimental. A model for remediation in an actual polluted site does not currently exist.Therefore, in this study, the dynamics was derived from the Michaelis–Menten model（when the mass ratio of emulsified vegetable oil and NB reached the critical value 91：1）. The effect of SO4^（2-）, NO3^-, Ca^（2＋）/Mg^（2＋）, and the grain size of aquifer media on the dynamics were studied, and the NB degradation dynamic model was then modified based on the most significant factors. Utilizing the model, the remediation time could be calculated in a contaminated site.

A novel intravenous general anesthetic—emulsified isoflurane:from bench to bedside

Application of volatile anesthetics greatly alters modern medicine.There are obvious advantages of volatile anesthetics such as strong anesthetic potency,rapid onset and elimination through respiration system.Isoflurane is one of the most widely used volatile anesthetics in clinic.Emulsified isoflurane,the emulsion of isoflurane,is a novel intravenous general anesthetic.With the development of emulsified isoflurane in the past fifteen years,its utility has spread from intravenous general anesthesia to various fields including regional anesthesia,organ protection,as well as anesthetic pharmacological study.In this review,we will summarize literatures of emulsified isoflurane about its history,clinical application and future potential utility in the above mentioned fields.

Laboratory investigation of emulsified asphalt binder modified with wood-derived nano-cellulose and nano paper-cellulose

Emulsified asphalt is the primary material for preventive maintenance and cold-mix paving,but its low cohesive strength and poor mechanical properties limit its wide application,even with polymer modification.In this study,Styrene-Butadiene Rubber(SBR)emulsified asphalt was modified with nano-cellulose materials,namely nano paper-cellulose(NPC)and wood-derived nano-cellulose(WDC),to improve its properties.A novel preparation method of nano-cellulose solution was developed,including blending,ultrasonic stirring,and centrifugal treatment.Four types of nano-cellulose solution(0.5%NPC,0.5%,1.0%,and 1.5%WDC by weight of water)were selected.The microscopy analysis indicated that 0.5%WDC emulsion had a smaller particle size than 1.5%WDC emulsion.The rheology test indicated that WDC modified residue improved rutting resistance with the increased solution dosage due to the cross-linking effect,but its creep-and-recovery performance was worse than that of SBR emulsion residue.The NPC modified binder had a higher rutting factor than WDC modified binder at the same dosage after short-term aging.In addition,1.0%WDC could be regarded as the optimal dosage in terms of fatigue and low-temperature performance.Furthermore,Fourier Transform Infrared Spectroscopy(FTIR)results showed that 0.5%NPC modified residue performed better in long-term aging resistance compared with 0.5%WDC modified asphalt.

Physical and emulsifying properties of pea protein:influence of combined physical modification by flaxseed gum and ultrasonic treatment

This study characterized and compared the physical and emulsifying properties of pea protein(PP)and its modified proteins(ultrasound treated-PP(PPU),flaxseed gum(FG)treated PP(PPFG)and ultrasound treated-PPFG(PPFGU)).The results showed FG triggered the formation of loosely attached complex with PP via physical modification under gentle magnetic stirring at pH 7.0,while ultrasound played an important role in reducing protein size,increasing surface hydrophobicity and molecular fluidity onto oil-water interface.So ultrasound further enhanced the interaction of PP with FG,and produced the PPFGU complex with smaller droplet size,higherζ-potential and lower turbidity.Further,combination of FG and ultrasound improved the physical properties of PP with higher viscosity,stiffer gels(defined as higher elastic modulus),stronger hydrophobic properties,better thermal stability,and fast protein absorption rate.Therefore,the PPFGU coarse emulsion performed highest emulsifying activity index(EAI)and emulsion stability index(ESI)that the stabilized nanoemulsion obtained smallest droplet size,higherζ-potential,and longest storage stability.The combination of FG and ultrasonic treatment will be an effective approach to improving the emulsifying property and thermal stability of PP,which can be considered as a potential plant-based emulsifier applied in the food industry.

Common Emulsifier Combination Skin Feeling Research and Recommendation

Emulsifier is an important component of emulsified skin care BASE(matrix),and the common influencing factors affecting the skin feel of BASE are:emollient,thickeners,and emulsifier.The choice of emulsifier is crucial to the skin feel of cosmetics.In this paper,12 classical emulsifiers were selected and 13 combinations of them were made.Thirteen creams were designed using the same formulation structure,their physicochemical indexes were determined,and their skin feel was tested and evaluated using five expert panel scores,with the test site being the hand.Physicochemical parameters included pH and viscosity.Skin feel indicators include:stickiness,silkiness,whiteheads,greasiness at the end of application,absorption,softness after use,etc.The BASE formulations of the creams were tested and evaluated by five experts.Recommendations were also made for the selection of emulsifier combinations in the design of cream BASE formulations.

丁草胺微乳液的研究(英文)

[Objective] The properties of butachlor microemulsion were studied for developing a new formulation of new pesticides.[Method]AT method was used to determine the pseudo-ternary phase diagram to confirm the formulation of butachlor microemulsion.Through the measurement of electrical conductivity,the W/O and O/W types in microemulsion region of butachlor/emulsifier/water system were confirmed and the change of phase behavior during preparation process was discussed.[Result]The dilution stability,low temperature stability,heat stability,ageing stability,density and viscosity etc.of butachlor microemulsion met the requirement of the experiments,which demonstrated the qualified quality of butachlor.The density decreased linearly with the increase of temperature and the change of viscosity with temperature conformed to Andrade equation.[Conclusion]The research was helpful to the application of butachlor microemulsion in pesticide formulation.

Preparation of A New Type of Stress-absorbed Material

Neoprene latex modified emulsified bitumen and fine aggregate are used to prepare a new type of stress-absorbed material, which has strong ability of anti-reflective cracking on asphalt concrete over layer-constructed upon a semi-rigid type base course or cement concrete pavement block. Experimental results demonstrate the stress-absorbed material have excellent mechanical properties including a low modulus of elasticity, high ultimate tensile stress and strain, and a strong distortion ability. Stress concentration in asphalt over layer originated by temperature changes and traffic loads can be alleviated.

Evaluation of the Antioxidant Activity of Ethanolic Extracts of Some Varieties of Onion

The content of polyphenolic in commercial onions has been determined. The antioxidant activity of their ethanolic extracts, as well as their effects on the oxidation of edible corn oil during accelerated ageing, was studied. Maceration of taxonomically identified commercial vegetable samples, previously peeled and thinly sliced, was carried out at ambient temperature, out of direct light, with occasional agitation and ultrasound, employing 95% ethyl alcohol as the extraction solvent, allowing them to stand for 7 days. The total polyphenolic contents were determined on the filtrated extracts using the Folin-Ciocalteau method. The antioxidant activity was evaluated on emulsions of ethanolic extracts of onion prepared in edible commercial corn oil, using sorbitan monooleate as emulsifying agent. The peroxide values were analyzed using the iodometric method;oxidation induction times were obtained from the peroxide evolution graphs, using the tangent method. Oil samples emulsified with ethanolic onion extracts showed an extension of the induction period. A 7 day ageing study at 45℃ was additionally performed to determine the conjugated dienes on pure commercial corn oil and its emulsions by visible spectrophotometry. The spectral analysis showed an increase of the measured absorbances in oil samples without additives and no change for the oils emulsified with onion extract. An increasing of diene values was observed for corn oil without additives during ageing;no changes in the value were observed in oils emulsified with onion extracts.

Evaluation of the Antioxidant Activity of Ethanolic Extracts of Some Varieties of Onions

The content of polyphenolic substances in commercial onions has been determined. The antioxidant activity of their ethanolic extracts, as well as their effects on the oxidation of edible corn oil during accelerated ageing was studied. Maceration of taxonomically identified commercial vegetable samples, previously peeled and thinly sliced, was carried out at ambient temperature, out of direct light, with occasional agitation and ultrasound, employing 95% ethyl alcohol as the extraction solvent, allowing them to stand for 7 days. The total polyphenolic contents were determined on the filtrated extracts using the Folin-Ciocalteau method. The antioxidant activity was evaluated on emulsions of ethanolic extracts of onion prepared in edible commercial corn oil, using sorbitan monooleate as emulsifying agent. The peroxide values were analyzed using the iodometric method;oxidation induction times were obtained from the peroxide evolution graphs, using the tan- gent method. Oil samples emulsified with ethanolic onion extracts showed an extension of the induction period. A 7-day ageing study at 45?C was additionally performed to determine the conjugated dienes on pure commercial corn oil and its emulsions by visible spectrophotometry. The spectral analysis showed an increase of the measured absorbancies in oil samples without additives and no change for the oils emulsified with onion extract. An increasing of diene values was observed for corn oil without additives during ageing;no changes in the value were observed in oils emulsified with onion extracts.

Effect of isoflurane on expression of NR4A1 in hypoxic pulmonary artery

Objective: To investigate the effects of emulsified isoflurane on hypoxic pulmonary artery endothelial cells (HPAECs) injury and orphan nuclear receptor subfamily 4A1 (NR4A1) expression. Methods: HPAECs were divided into normal control group, model group and test group. Normal control group was cultured under normoxia. Cells in model group and test group were treated in a hypoxic chamber with oxygen concentration of about 3% (95% N2+ 5% CO2) for 2 h. The final concentration of 1 mmol·L-1 emulsified isoflurane was added to the test group, and 30% Intralipid? was added to the normal control group and the model group. MTT method was used to detect cell proliferation, Hoechst 33258 nuclear staining was used to detect cell apoptosis, Griess method was used to detect the production of NO in cell supernatant, and real-time fluorescence quantitative PCR (q-RT-PCR) was used to detect the expression of NR4A1 in cells. Results: After 12 h of intervention, the cell viability of normal control group, model group and test group were (98.45±2.41)%, (15.46±2.69)%, (79.52±4.16)%, the apoptosis rate were (2.51±0.36)%, (50.12±3.36)%, (22.15±3.42)%respectively, the concentration of NO in the culture supernatant were (59.52±4.1) μmol·L^-1, (25.16±4.85) μmol·L^-1, (43.58±6.19) μmol·L^-1, and the relative expression of NR4A1 were 1.00±0.09, 5.89±0.41, 2.39±0.24, respectively. The difference was statistically significant (P<0.05). Conclusion: Emulsified isoflurane can promote the proliferation, inhibit apoptosis and increase NO production of hypoxic HPAECs. NR4A1 may be involved in the endogenous protective mechanism of endothelial cell injury after hypoxia.

Regenerative Therapeutic Applications of Mechanized Lipoaspirate Derivatives

Autologous adipose tissue is one of the most commonly used fillers.Plastic surgeons are increasingly using it in aesthetic or reconstructive surgery owing to its abundant source,easy availability,and minimal invasiveness.Increasing amount of evidence has shown its reparative ability rather than just filling utility due to the presence of adipose-derived stem cells(ADSCs)that exhibit multipotential differentiation and paracrine characteristics.However,traditional enzymatic isolation of ADSCs is often difficult in clinical settings,limiting its application.Recently,with the development of mechanical techniques for preparation of lipoaspirates,bioactive adipose tissue can be successfully identified and isolated.Such components with therapeutic potential might also be helpful in tissue repair and regeneration.In this article,we introduced several types of mechanized lipoaspirates derivatives(such as emulsified fat,adipose extracellular matrix(ECM),and cell-free extraction)and their applications from bench to bedside.

Influence of an emulsifier on the pressure desensitization of emulsion explosives

The desensitization degree of emulsion explosives （EE） was calculated with the peak pressure of explosion shock waves tested in water. To an explosive, the less the desensitization degree, the better the compression resistance, so the compression resistance of an explosive can be compared and analyzed quantificationally with the desensitization degree. The influence of an emulsifier on the pressure desensitization of EE was studied, including the content and category of emulsifiers. Three kinds of emulsifiers （Span-80, compound emulsifier, and T-152） were used in the tests. The experimental results show that both the content and category of emulsifiers make a great effect on the pressure desensitization of EE. The desensitization degree of EE reduces with the emulsifier content being increased, but there is an optimal content of an emulsifier for the compression resistance of EE. While the content of Span-80 reaches 4wt%, the desensitization degree of EE becomes a minimal value, and augments somewhat if the emulsifier content is increased more. That is to say, the compression resistance of EE becomes the highest while the content of Span-80 is 4wt%, and the compression resistance will decline if the content of Span-80 is increased more. The compression resistance of the explosive emulsified by compound emulsifier is the highest among all the explosives, when the content of the whole components and manufacturing engineering are kept invariable.

Preparation of multihollow P(St-MAA) particles by sequence soap-free/soap emulsion polymerization and followed by stepwise alkali/acid posttreatment

The effects of ionic emulsifier, sodium dodecylbenzene sulfate (SDBS), on the formation of the multihollow structures in sub-micron sized polymer particles produced by alkali/acid posttreatment were investigated. The original latex particles with narrow size distribution were synthesized by a new sequence emulsifier-free/emulsifier emulsion copolymerization of styrene (St) and methacrylic acid (MAA). Results indicated that the pore size decreased and the pore number increased with the increase of SDBS amount, and the morphology of the posttreated latex particles was also significantly influenced by the introducing time of SDBS in the preparation of the original latex particles, and a suitable introducing time was 3 h of polymerization. (c) 2007 Cheng You Kan. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.