The impact of Internet access on household dietary quality:Evidence from rural China

Over the past few decades,the Internet has rapidly diffused across China.The spread of the Internet has had a profound economic and social impact on Chinese rural areas.Existing research shows that Internet access significantly impacts agricultural production and improves smallholder farmers’income.Beyond these,the Internet can affect other dimensions of social welfare.However,research about the impact of Internet access on dietary quality in rural China remains scarce.This study utilizes multi-period panel data from Fixed Observation Point in rural China from 2009 to 2015 to estimate the impact of Internet access on dietary quality and food consumption of rural households and conducts a causal analysis.Regression models with time and household fixed effects allow robust estimation while reducing potential issues of unobserved heterogeneity.The estimates show that Internet access has significantly increased rural household dietary quality(measured by the Chinese Diet Balance Index).Further research finds that Internet access has increased the consumption of animal products,such as aquatic and dairy products.We also examine the underlying mechanisms.Internet access improves dietary quality and food consumption mainly through increasing household income and food expenditure.These results encourage the promotion of Internet access as a valuable tool for nutritional improvements,especially in rural areas.

An Experimental Analysis of Gas-Liquid Flow Breakdown in a T-Junction

When a gas-liquid two-phase flow(GLTPF)enters a parallel separator through a T-junction,it generally splits unevenly.This phenomenon can seriously affect the operation efficiency and safety of the equipment located downstream.In order to investigate these aspects and,more specifically,the so-called bias phenomenon(all gas and liquid flowing to one pipe,while the other pipe is a liquid column that fluctuates up and down),laboratory experiments were carried out by using a T-junction connected to two parallel vertical pipes.Moreover,a GLTPF prediction model based on the principle of minimum potential energy was introduced.The research results indicate that this model can accurately predict the GLTPF state in parallel risers.The boundary of the slug flow and the churn flow in the opposite pipe can be predicted.Overall,according to the results,the pressure drop curves of the two-phase flow in the parallel risers are basically the same when there is no bias phenomenon,but the pressure drop in the parallel riser displays a large deviation when there is a slug flow-churn flow.Only when the parallel riser is in a state of asymmetric flow and one of the risers produces churn flow,the two-phase flow is prone to produce the bias phenomenon.

Does China's digital economy contribute to low-carbon transition?

The digital economy,as a new emerging economic form,has become an important power for realizing Chinese-style modernization and promoting green development in China.This paper measures the digital economy and low-carbon transition index based on the data of 30 provinces in China from 2013 to 2020 and analyzes the mechanism and path of the digital economy affecting low-carbon transition using the fixed effect panel data model and the threshold effect model.It is found that,(1)The digital economy and low-carbon transition in China are various in different regions,with characteristics of being unbalanced and insufficient.(2)The digital economy significantly promotes low-carbon transition,with the greatest influence in the Central region,followed by the Eastern region and the Western region.Under different dimensions,the development of informatization and digital transactions promote low-carbon transition,but the development of the internet plays an inhibiting role.(3)The higher the degree of urbanization and environmental regulation,the greater the influence of the digital economy on low-carbon transition.

INTERACTION MODELS FOR EFFECTIVE THERMAL AND ELECTRIC CONDUCTIVITIES OF CARBON NANOTUBE COMPOSITES

The present article provides supplementary information of previous works of analytic models for predicting conductivity enhancements of carbon nanotube composites. The models, though fairly simple, are able to take account of the effects of conductivity anisotropy, nonstraightness, and aspect ratio of the CNT additives on the conductivity enhancement of the composite and to give predictions agreeing well with existing experimental data. The omitted detailed derivation of this model is demonstrated in the present article with a more systematical analysis, which may help with further development in this direction. Furthermore, the effects of various orientation distributions of CNTs are reported here for the first time. The information may be useful in design or fabrication technology of CNT composites for better or specified conductivities.

EMPIRICAL BAYES TEST PROBLEMS OF VARIANCE COMPONENTS IN RANDOM EFFECTS MODEL

Bayes decision rule of variance components for one-way random effects model is derived and empirical Bayes (EB) decision rules are constructed by kernel estimation method. Under suitable conditions, it is shown that the proposed EB decision rules are asymptotically optimal with convergence rates near O(n-1/2). Finally, an example concerning the main result is given.

Modelling Study to Compare the Flow and Heat Transfer Characteristics of Low-Power Hydrogen,Nitrogen and Argon Arc-Heated Thrusters

A modelling study is performed to compare the plasma flow and heat transfer characteristics of low-power arc-heated thrusters （arcjets） for three different propellants： hydrogen, nitrogen and argon. The all-speed SIMPLE algorithm is employed to solve the governing equations, which take into account the effects of compressibility, Lorentz force and Joule heating, as well as the temperature- and pressure-dependence of the gas properties. The temperature, velocity and Mach number distributions calculated within the thruster nozzle obtained with different propellant gases are compared for the same thruster structure, dimensions, inlet-gas stagnant pressure and arc currents. The temperature distributions in the solid region of the anode-nozzle wall are also given. It is found that the flow and energy conversion processes in the thruster nozzle show many similar features for all three propellants. For example, the propellant is heated mainly in the near-cathode and constrictor region, with the highest plasma temperature appearing near the cathode tip; the flow transition from the subsonic to supersonic regime occurs within the constrictor region; the highest axial velocity appears inside the nozzle; and most of the input propellant flows towards the thruster exit through the cooler gas region near the anode-nozzle wall. However, since the properties of hydrogen, nitrogen and argon, especially their molecular weights, specific enthMpies and thermal conductivities, are different, there are appreciable differences in arcjet performance. For example, compared to the other two propellants, the hydrogen arcjet thruster shows a higher plasma temperature in the arc region, and higher axial velocity but lower temperature at the thruster exit. Correspondingly, the hydrogen arcjet thruster has the highest specific impulse and arc voltage for the same inlet stagnant pressure and arc current. The predictions of the modelling are compared favourably with available experimental results.

THEORETICAL MODEL OF EFFECTIVE STRESS COEFFICIENT FOR ROCK/SOIL-LIKE POROUS MATERIALS

Physical mechanisms and influencing factors on the effective stress coefficient for rock/soil-like porous materials are investigated, based on which equivalent connectivity index is proposed. The equivalent connectivity index, relying on the meso-scale structure of porous material and the property of liquid, denotes the connectivity of pores in Representative Element Area （REA）. If the conductivity of the porous material is anisotropic, the equivalent connectivity index is a second order tensor. Based on the basic theories of continuous mechanics and tensor analysis, relationship between area porosity and volumetric porosity of porous materials is deduced. Then a generalized expression, describing the relation between effective stress coefficient tensor and equivalent connectivity tensor of pores, is proposed, and the expression can be applied to isotropic media and also to anisotropic materials. Furthermore, evolution of porosity and equivalent connectivity index of the pore are studied in the strain space, and the method to determine the corresponding functions in expressions above is proposed using genetic algorithm and genetic programming. Two applications show that the results obtained by the method in this paper perfectly agree with the test data. This paper provides an important theoretical support to the coupled hydro-mechanical research.

Chemopreventive Effects of Black Tea Polyphenols in Mouse Skin Model of Carcinogenesis

In the present investigations, the antitumorigenic effect of black tea polyphenols (BTP) in twcrstage mouse skin model of carcinogenesis was studied. The animals were initiated with a single 'subcarcinogenic' topical dose (52 μg/200 μl acetone ) of 7, 12-dimethylbenzanthracene (DMBA). To evaluate the anti-tumour initiating activity, BTP was topically applied twice a week for three weeks prior to DMBA application, followed by topical treatment with 12-o-tetradecanoyl phorbol-13-acetate (TPA) (5 μg/200 μl acetone, 2x/wk. ) as promoter. For evaluation of antitumor promoting activity, BTP was applied prior to each treatment of TPA. BTP application showed marked inhibitory effect as antitumour initiator as well as antitumour promoter in mouse skin medel of two-stage carcinogenesis. Since initiation involves genetic pathway and tumour promotion involves epigenetic pathway, it seems that BTP exerts its antitumorigenic effect by altering both genetic and epigenetic pathways

3-D modeling of rock burst in pillar No. 19 of Fetr6 chromite mine

Fetr6 is an underground mine in which chromite is extracted using stope and pillar mining method. Despite of all improving works such as roof supporting and replacing of ore pillars with concrete pillars, pillar No. 19 failed and other pillars failed progressively as a domino effect and 4000 m2 of mine collapsed within a few minutes, consequently. For detail investigation, two 3-D numerical models were developed by 3Dec. The first, a base model, was used for estimation of stress on pillars just before failure and the other for investigation of rock burst in pillar No. 19. The results show that discontinuity parameters such as friction angle and shear stiffness is critical parameters in this pillar failure. In addition, it indicates that W/H ratio equal 0.3, the lack of ore extraction strategy and inadequate roof support are the major reasons for this failure. In this paper, the procedure of study was described.

Effects of Three Typical Resistivity Models on Pulsed Inductive Plasma Acceleration Modeling

The effects of three different typical resistivity models（Spitzer, Z＆L and M＆G） on the performance of pulsed inductive acceleration plasma are studied. Numerical results show that their influences decrease with the increase of the plasma temperature. The significant discriminations among them appear at the plasma temperature lower than 2.5 eV, and the maximum gap of the pulsed inductive plasma accelerated efficiency is approximately 2.5%.Moreover, the pulsed inductive plasma accelerated efficiency is absolutely related to the dynamic impedance parameters, such as voltage, inductance, capacitance and flow rate. However, the distribution of the efficiency as a function of plasma temperature with three resistivity models has nothing to do with the dynamic impedance parameter.

Numerical analysis of submarine landslides using a smoothed particle hydrodynamics depth integral model

Submarine landslides can cause severe damage to marine engineering structures. Their sliding velocity and runout distance are two major parameters for quantifying and analyzing the risk of submarine landslides.Currently, commercial calculation programs such as BING have limitations in simulating underwater soil movements. All of these processes can be consistently simulated through a smoothed particle hydrodynamics（SPH） depth integrated model. The basis of the model is a control equation that was developed to take into account the effects of soil consolidation and erosion. In this work, the frictional rheological mode has been used to perform a simulation study of submarine landslides. Time-history curves of the sliding body＇s velocity, height,and length under various conditions of water depth, slope gradient, contact friction coefficient, and erosion rate are compared; the maximum sliding distance and velocity are calculated; and patterns of variation are discussed.The findings of this study can provide a reference for disaster warnings and pipeline route selection.

Bootstrap inference of the skew-normal two-way classification random effects model with interaction

In this paper,we consider the statistical inference problems for the fixed effect and variance component functions in the two-way classification random effects model with skewnormal errors.Firstly,the exact test statistic for the fixed effect is constructed.Secondly,using the Bootstrap approach and generalized approach,the one-sided hypothesis testing and interval estimation problems for the single variance component,the sum and ratio of variance components are discussed respectively.Further,the Monte Carlo simulation results indicate that the exact test statistic performs well in the one-sided hypothesis testing problem for the fixed effect.And the Bootstrap approach is better than the generalized approach in the one-sided hypothesis testing problems for variance component functions in most cases.Finally,the above approaches are applied to the real data examples of the consumer price index and value-added index of three industries to verify their rationality and effectiveness.

Posterior propriety in nonparametric mixed efects model

It is well known that spline smoothing estimator relates to the Bayesian estimate under partially informative normal prior. In this paper, we derive the conditions for the pro- priety of the posterior in the nonparametric mixed effects model under this class of partially informative normal prior for fixed effect with inverse gamma priors on the variance compo- nents and hierarchical priors for covariance matrix of random effect, then we explore the Gibbs sampling procedure.

Modeling and numerical simulation of electrical and optical characteristics of a quantum dot light-emitting diode based on the hopping mobility model:Influence of quantum dot concentration

We present a comprehensive numerical framework for the electrical and optical modeling and simulation of hybrid quantum dot light-emitting diodes(QD-LEDs).We propose a model known as hopping mobility to calculate the carrier mobility in the emissive organic layer doped with quantum dots(QDs).To evaluate the ability of this model to describe the electrical characteristics of QD-LEDs,the measured data of a fabricated QD-LED with different concentrations of QDs in the emissive layer were taken,and the corresponding calculations were performed based on the proposed model.The simulation results indicate that the hopping mobility model can describe the concentration dependence of the electrical behavior of the device.Then,based on the continuity equation for singlet and triplet excitons,the exciton density profiles of the devices with different QD concentrations were extracted.Subsequently,the corresponding luminance characteristics of the devices were calculated,where the results are in good agreement with the experimental data.

Electronic Structure Effect on Model Cluster for L1_2 Structure of Al_3Ti Intermetallic Compound with an Addition of Alloying Elements Fe, Ni and Cu

By use of self-consistent field Xα scattered-wave (SCF-Xα-SW) method, the electronic structure was calculated for four models of Ti4Al14X (X=Al, Fe, Ni and Cu) clusters. The Ti4Al14X cluster was developed based on L12 Al3Ti-base intermetallic compound. The results are presented using the density of states (DOS) and one-electron properties, such as relative binding tendency between the atom and the model cluster, and hybrid bonding tendency between the alloying element and the host atoms. By comparing the four models of Ti4Al14X cluster, the effect of the Fe, Ni or Cu atom on the physical properties of Al3Ti-based L12 intermetallic compounds is analyzed. The results indicate that the addition of the Fe, Ni or Cu atom intensifies the relative binding tendency between Ti atom and Ti4Al14X cluster. It was found that the Fermi level (EF) lies in a maximum in the DOS for Ti4Al14Al cluster; on the contrary, the EF comes near a minimum tn the DOS for Ti4Al14X (X=Fe, Ni and Cu) cluster. Thus the L12 crystal structure for binary Al3Ti alloy is unstable, and the addition of the Fe, Ni or Cu atom to Al3Ti is benefical to stabilize L12 crystal structure. The calculation also shows that the Fe, Ni or Cu atom strengthens the hybrid bonding tendency between the central atom and the host atoms for Ti4Al14X cluster and thereby may lead to the constriction of the lattice of Al3Ti-base intermetallic compounds.

Evaluation of the Effects of Cypermethrin on Female Reproductive Function by Using Rabbit Model and of the Protective Role of Chinese Propolis

The prophylactic effects of Chinese propolis against cypermethrin toxicity were evaluated by performing ovary and uterus histopathology, as well as by characterizing ovarian function, embryos, and litters. Cypermethrin induced atypia in the ovary and uterus, and decreased the ovulation sites and the number of embryos. Cypermethrin-induced oxidative stress during pregnancy, decreased the parturition rate as well as the number and weight of offspring and increased the incidence of morphological malformations in the offspring. Administration of propolis to cypermethrin-treated animals mitigated cypermethrin-induced reproductive toxicity.

Bias and Mean Square Error of Reliability Estimators under the One and Two Random Effects Models: The Effect of Non-Normality

The coefficient of reliability is often estimated from a sample that includes few subjects. It is therefore expected that the precision of this estimate would be low. Measures of precision such as bias and variance depend heavily on the assumption of normality, which may not be tenable in practice. Expressions for the bias and variance of the reliability coefficient in the one and two way random effects models using the multivariate Taylor’s expansion have been obtained under the assumption of normality of the score (Atenafu et al. [1]). In the present paper we derive analytic expressions for the bias and variance, hence the mean square error when the measured responses are not normal under the one-way data layout. Similar expressions are derived in the case of the two-way data layout. We assess the effect of departure from normality on the sample size requirements and on the power of Wald’s test on specified hypotheses. We analyze two data sets, and draw comparisons with results obtained via the Bootstrap methods. It was found that the estimated bias and variance based on the bootstrap method are quite close to those obtained by the first order approximation using the Taylor’s expansion. This is an indication that for the given data sets the approximations are quite adequate.

Modelling Magnetoresistance Effect in Limited Anisotropic Semiconductors

A macroscopic model of the magnetoresistance effect in fimited anisotropic semiconductors is built. This model allows us to solve the problem of measurement of physical magnetoresistance components of crystals and films. Based on a unified mathematical model the method is worked out enabling us to measure tensor components of the specific electrical resistance and the relative magnetoresistance of anisotropic semiconductors simultaneously.

Modeling the Synergetic Effect of Various Factors on Chloride Transport in Nonsaturated Concrete

Diffusion has been systematically described as the main mechanism of chloride transport in reinforced concrete（RC） structure, especially when the concrete is in a saturated state. However, the single mechanism of diffusion is not able to describe the actual chloride ingress in the nonsaturated concrete. Instead, it is dominated by the interaction of diffusion and convection. With the synergetic effects of various factors taken into account, this study aimed to modify and develop an analytical convection- diffusion coupling model for chloride transport in nonsaturated concrete. The model was verified by simulation of laboratory tests and field measurement. The results of comparison study demonstrate that the analytical model developed in this study is efficient and accurate in predicting the chloride profiles in the nonsaturated concrete.

A FGR Software Model for Measuring the Effect of Technological Progress

The work of quantitative studying the effect of technological progress on economic growth, being of great complexity and far-reaching significance, has become a quite popular research topic in the world. In recent years there are a large number of scientists who are engaged in this research both at home and abroad.