Electrically controllable spin filtering in zigzag phosphorene nanoribbon based normal–antiferromagnet–normal junctions

We investigated the electric controllable spin-filtering effect in a zigzag phosphorene nanoribbon(ZPNR) based normal–antiferromagnet–normal junction. Two ferromagnets are closely coupled to the edges of the nanoribbon and form the edge-to-edge antiferromagnetism. Under an in-plane electric field, the two degenerate edge bands of the edge-to-edge antiferromagnet split into four spin-polarized sub-bands and a 100% spin-polarized current can be easily induced with the maximal conductance 2e~2/h. The spin polarization changes with the strength of the electric field and the exchange field,and changes sign at opposite electric fields. The spin-polarized current switches from one edge to the other by reversing the direction of the electric field. The edge current can also be controlled spatially by changing the electric potential of the scattering region. The manipulation of edge current is useful in spin-transfer-torque magnetic random-access memory and provides a practical way to develop controllable spintronic devices.

Research on Electrical Automation Control Design Based on PLC Technology

As science and technology continue to progress forward,electrical automation engineering is also developing,of which programmable logic controller(PLC)technology is widely being used.Through the integration of PLC technology and traditional electrical automation technology,good development of modern science and technology is promoted while traditional automation is preserved.The development of electrical engineering can greatly improve the strength of science,technology,and economy in our country.Based on PLC technology,this paper analyzes the design of electrical automation control.

Fault tolerant control of electric pitch control system based on single current detection

In view of the current sensors failure in electric pitch system,a variable universe fuzzy fault tolerant control method of electric pitch control system based on single current detection is proposed.When there is single or two-current sensor fault occurs,based on the proposed method the missing current information can be reconstructed by using direct current（DC）bus current sensor and the three-phase current can be updated in time within any two adjacent sampling periods,so as to ensure stability of the closed-loop system.And then the switchover and fault tolerant control of fault current sensor would be accomplished by fault diagnosis method based on adaptive threshold judgment.For the reconstructed signal error caused by the modulation method and the main control target of electric pitch system,a variable universe fuzzy control method is used in the speed loop,which can improve the anti-disturbance ability to load variation,and the robustness of fault tolerance system.The results show that the fault tolerant control method makes the variable pitch control system still has ideal control characteristics in case of sensor failure although part of the system performance is lost,thus the correctness of the proposed method is verified.

Wide speed range for traction motor in braking force of electric braking control system

A vehicle stopping method using an electric brake until a traction motor is stopped is studied. At the moment of vehicle stop, electric brake is changed to control mode where torque is reduced at a low speed. Gradient is controlled by estimating the load torque of motor, thereby traction motor is not rotated after stop. In addition, coasting operation and brake test are performed from normal-opposite operation and start using a small-scale model comprising the inertial load equipment and the power converter. Further, traction motor is made to be equipped with a suspension torque. Pure electric braking that makes traction motor stop by an air brake at the time of stop is also implemented. Constant torque range and constant power range are expanded during braking so that braking force is secured with the electric brakes even in high speed region. Therefore, vehicle reduction effect can be expected by reducing parts related with an air brake which is not used frequently by using a pure electric brake in the M car in wide speed region. Further, maintenance of brake system can be reduced. Besides, ride comfort of passenger in the electric rail car, energy efficiency improvement, and noise reduction effect can be additionally expected. Further, an improved brake method that uses only an electric brake till motor stop is proposed by comparing those in the blending brake that uses an air brake while reducing brake torque at vehicle stop.

Oscillation of Dzyaloshinskii–Moriya interaction driven by weak electric fields

Dzyaloshinskii–Moriya interaction(DMI) is under extensive investigation considering its crucial status in chiral magnetic orders, such as Néel-type domain wall(DW) and skyrmions. It has been reported that the interfacial DMI originating from Rashba spin–orbit coupling(SOC) can be linearly tuned with strong external electric fields. In this work, we experimentally demonstrate that the strength of DMI exhibits rapid fluctuations, ranging from 10% to 30% of its original value, as a function of applied electric fields in Pt/Co/MgO heterostructures within the small field regime(< 10-2V/nm). Brillouin light scattering(BLS) experiments have been performed to measure DMI, and first-principles calculations show agreement with this observation, which can be explained by the variation in orbital hybridization at the Co/MgO interface in response to the weak electric fields. Our results on voltage control of DMI(VCDMI) suggest that research related to the voltage control of magnetic anisotropy for spin–orbit torque or the motion control of skyrmions might also have to consider the role of the external electric field on DMI as small voltages are generally used for the magnetoresistance detection.

Real-time and wearable functional electrical stimulation system for volitional hand motor function control using the electromyography bridge method

Voluntary participation of hemiplegic patients is crucial for functional electrical stimulation therapy.A wearable functional electrical stimulation system has been proposed for real-time volitional hand motor function control using the electromyography bridge method.Through a series of novel design concepts,including the integration of a detecting circuit and an analog-to-digital converter,a miniaturized functional electrical stimulation circuit technique,a low-power super-regeneration chip for wireless receiving,and two wearable armbands,a prototype system has been established with reduced size,power,and overall cost.Based on wrist joint torque reproduction and classification experiments performed on six healthy subjects,the optimized surface electromyography thresholds and trained logistic regression classifier parameters were statistically chosen to establish wrist and hand motion control with high accuracy.Test results showed that wrist flexion/extension,hand grasp,and finger extension could be reproduced with high accuracy and low latency.This system can build a bridge of information transmission between healthy limbs and paralyzed limbs,effectively improve voluntary participation of hemiplegic patients,and elevate efficiency of rehabilitation training.

Distributed Model Predictive Load Frequency Control of Multi-area Power System with DFIGs

Reliable load frequency control LFC is crucial to the operation and design of modern electric power systems. Considering the LFC problem of a four-Area interconnected power system with wind turbines, this paper presents a distributed model predictive control DMPC based on coordination scheme. The proposed algorithm solves a series of local optimization problems to minimize a performance objective for each control area. The generation rate constraints GRCs, load disturbance changes, and the wind speed constraints are considered. Furthermore, the DMPC algorithm may reduce the impact of the randomness and intermittence of wind turbine effectively. A performance comparison between the proposed controller with and without the participation of the wind turbines is carried out. Analysis and simulation results show possible improvements on closed-loop performance, and computational burden with the physical constraints. © 2014 Chinese Association of Automation.

Direct Yaw Moment Control for Distributed Drive Electric Vehicle Handling Performance Improvement

For a distributed drive electric vehicle（DDEV） driven by four in-wheel motors, advanced vehicle dynamic control methods can be realized easily because motors can be controlled independently, quickly and precisely. And direct yaw-moment control（DYC） has been widely studied and applied to vehicle stability control. Good vehicle handling performance： quick yaw rate transient response, small overshoot, high steady yaw rate gain, etc, is required by drivers under normal conditions, which is less concerned, however. Based on the hierarchical control methodology, a novel control system using direct yaw moment control for improving handling performance of a distributed drive electric vehicle especially under normal driving conditions has been proposed. The upper-loop control system consists of two parts： a state feedback controller, which aims to realize the ideal transient response of yaw rate, with a vehicle sideslip angle observer; and a steering wheel angle feedforward controller designed to achieve a desired yaw rate steady gain. Under the restriction of the effect of poles and zeros in the closed-loop transfer function on the system response and the capacity of in-wheel motors, the integrated time and absolute error（ITAE） function is utilized as the cost function in the optimal control to calculate the ideal eigen frequency and damper coefficient of the system and obtain optimal feedback matrix and feedforward matrix. Simulations and experiments with a DDEV under multiple maneuvers are carried out and show the effectiveness of the proposed method： yaw rate rising time is reduced, steady yaw rate gain is increased, vehicle steering characteristic is close to neutral steer and drivers burdens are also reduced. The control system improves vehicle handling performance under normal conditions in both transient and steady response. State feedback control instead of model following control is introduced in the control system so that the sense of control intervention to drivers is relieved.

Room-temperature electric control of exchange bias effect in CoO1-δ/Co films using Pb(Mg1/3Nb2/3)0.7Ti0.3O3 (110) substrates

Significant electric control of exchange bias effect in a simple CoO1-δ/Co system, grown on piezoelectric Pb(Mg1/3Nb2/3)0.7Ti0.3O3 (110) (PMN-PT) substrates, is achieved at room temperature. Obvious changes in both the coercivity field (HC) and the exchange bias field (HE), of 31% and 5%, respectively, have been observed when the electric field is applied to the substrate. While the change of coercivity is related to the enhanced uniaxial anisotropy in the ferromagnetic layer, the change of the exchange bias field can only originate from the spin reorientation in the antiferromagnetic CoO1-δ layer caused by the strain-induced magnetoelastic effect. A large HE/HC > 2, and HE~ 110 Oe at room temperature, as well as the low-energy fabrication of this system, make it a practical system for spintronic device applications.

Sliding Mode Control Approach for Electrically Controllable Clutch of AMT Based on the Feedback Linearization

A sliding mode control approach based on the feedback linearization is proposed for the electrically controllable clutch of AMT vehicles. The nonlinear dynamic model for the hydraulic actuator associated with clutch is established. By means of the exact feedback linearization procedure of differential geometry, an equivalent, fully controllable and linear model is derived via a homomorphic transformation for the AMT clutch system.Furthermore, a sliding mode control is introduced to improve robustness. The tracking tests are performed using the sliding mode control on a Santana LX passenger car, and the experimental results prove that this nonlinear controller is of fine robustness and high degree of tracking accuracy.

Electrical control of magnetism in oxides

Recent progress in the electrical control of magnetism in oxides,with profound physics and enormous potential applications,is reviewed and illustrated.In the first part,we provide a comprehensive summary of the electrical control of magnetism in the classic multiferroic heterostructures and clarify the various mechanisms lying behind them.The second part focuses on the novel technique of electric double layer gating for driving a significant electronic phase transition in magnetic oxides by a small voltage.In the third part,electric field applied on ordinary dielectric oxide is used to control the magnetic phenomenon originating from charge transfer and orbital reconstruction at the interface between dissimilar correlated oxides.At the end,we analyze the challenges in electrical control of magnetism in oxides,both the mechanisms and practical applications,which will inspire more in-depth research and advance the development in this field.

Capillary Electrophoretic Separation of Proteins under the Control of Radial Electric Field

Separation of basic proteins was performed using a homemade field-modulated capillary electrophoresis system. The resolution. elution and even wall adsorption can be regulated by ad-lusting the radial rather than axial voltage applied. Selection of running buffer and pH was found to be critical.

Photo-Doped Active Electrically Controlled Terahertz Modulator

We demonstrate an electric-controlled terahertz（THz） modulator which can be used to realize amplitude modulation of terahertz waves with slight photo-doping. The THz pulse transmission was efficiently modulated by electrically controlling the monolayer silicon-based device. The modulation depth reached 100% almost when the applied voltage was 7V at an external laser intensity of 0.6W/cm2. The saturation voltage reduced with the increase of the photo-excited intensity. In a THz continuous wave（CW）system, a significant fall in both THz transmission and reflection was also observed with the increase of applied voltage. This reduction in the THz transmission and reflection was induced by the absorption for electron injection. The results show that a high-efficiency and high modulation depth broadband electric-controlled terahertz modulator in a pure Si structure has been realized.

Simulation of optical and electrical synaptic functions in MoS_(2)/α-In_(2)Se_(3) heterojunction memtransistors

Memtransistors combine memristors and field-effect transistors, which can introduce multi-port control and have significant applications for enriching storage methods. In this paper, multilayer α-In2Se3and MoS2were transferred to the substrate by the mechanical exfoliation method, then a heterojunction MoS_(2)/α-In_(2)Se_(3) memtransistor was prepared. Neural synaptic simulations were performed using electrical and optical pulses as input signals. Through measurements, such as excitatory/inhibitory post-synaptic current(EPSC/IPSC), long-term potentiation/depression(LTP/LTD), and paired-pulse facilitation/depression(PPF/PPD), it can be found that the fabricated device could simulate various functions of neural synapses well, and could work as an electronic synapse in artificial neural networks, proposing a possible solution for neuromorphic storage and computation.

The Research and Application of the Anti-Interference Techniques of Electronic Device in Power System

This paper presents the study and application of the electronic device anti-interference techniques underhigh voltage and/or heavy current electro-magnetic circumstance in power system.[

Designing and characteristics analysis of electric suspensions with symmetrically arranged two slider-rods

An innovative design of electric suspensions was developed in this study to help realize slow active suspension easily and quickly.This design was driven by screw through double slider-rod arranged symmetrically as a substitute for two springs.Based on a mathematical modeling,suspension parameters were introduced for a certain type of wheeled vehicles.The functions and its mechanism in regulating terrain clearance and adjusting attitudes were subsequently explained respectively,together with its semi-active control mechanism and characteristics In conclusion,our data in the study show that the new mechanical design of suspensions not only could realize adjusting terrain clearance and static vehicle pose,but also had an ideal stiffness that could realize a semi-active suspension function through adjusting suspension＇s stiffness.Therefore it can bequite suitable for off-road wheeled vehicles and military wheeled vehicles.

RULED SURFACE MACHINING BY 4-AXES SIMULTANEOUS CONTROL WIRE-EDM

On the tasis of study in the mathematical model of 3-dimensional ruled surface (RS),this paper introduces a new concept of distance paramcter (DP) and also puts forward that themethod of modeling a RS depends on not only two boundary curves but also DP. According toabove theory, the formulas to calculate corresponding point coordinates to any kind of top and bot-tom profile of a workpiece and formulas to calcuate the maximum inclination angle of ruling linehave been obtained. Then a different top and bottom RS mathining method including profile withline-are combination as well as parametric curves has been achieved by 4-axes simultancous con-trol programming proposed.

Modeling and test on height adjustment system of electrically-controlled air suspension for agricultural vehicles

To reduce the damages of pavement,vehicle components and agricultural product during transportation,an electric control air suspension height adjustment system of agricultural transport vehicle was studied by means of simulation and bench test.For the oscillation phenomenon of vehicle height in driving process,the mathematical model of the vehicle height adjustment system was developed,and the controller of vehicle height based on single neuron adaptive PID control algorithm was designed.The control model was simulated via Matlab/Simulink,and bench test was conducted.Results show that the method is feasible and effective to solve the agricultural vehicle body height unstable phenomenon in the process of switching.Compared with other PID algorithms,the single neuron adaptive PID control in agricultural transport vehicle has shorter response time,faster response speed and more stable switching state.The stability of the designed vehicle height adjustment system and the ride comfort of agricultural transport vehicle were improved.

The Electrical Control System PLC Transformation of The XA6132 Milling

For the electrical control system of XA6132 milling machine circuit complexity, reliability and flexibility, high failure rate. Mitsubishi FX2N-40MR programmable controller is used to improve the performance and efficiency of the entire electrical control system by technological transformation. Mitsubishi FX2N-d0MRPLC on electrical control system transformation can expand link to the technological transformation of the similar equipments.

The Electrical Control System PLC Transformation of The T68 Boring

T68 boring machine electric control system circuit is complex, its reliability and flexibility is poor with high failure rate. The mitsubishi FX2N-40MR Programmable controller for the technical innovation of electric control system improves the work performance of the whole electric control system and the work efficiency. This paper introduces the mitsubishi FX2N-40MR PLC in T68 boring machine electric control system, the application of the elaborated system＇s hardware and PLC program design can provide work for technical reform of similar equipment.