Thermal analysis for brake disks of SiC/6061 Al alloy co-continuous composite for CRH3 during emergency braking considering airflow cooling

The mass of high-speed trains can be reduced using the brake disk prepared with SiC network ceramic frame reinforced 6061 aluminum alloy composite （SiCn/Al）. The thermal and stress analyses of SiCn/Al brake disk during emergency braking at a speed of 300 km/h considering airflow cooling were investigated using finite element （FE） and computational fluid dynamics （CFD） methods. All three modes of heat transfer （conduction, convection and radiation） were analyzed along with the design features of the brake assembly and their interfaces. The results suggested that the higher convection coefficients achieved with airflow cooling will not only reduce the maximum temperature in the braking but also reduce the thermal gradients, since heat will be removed faster from hotter parts of the disk. Airflow cooling should be effective to reduce the risk of hot spot formation and disc thermal distortion. The highest temperature after emergency braking was 461 °C and 359 °C without and with considering airflow cooling, respectively. The equivalent stress could reach 269 MPa and 164 MPa without and with considering airflow cooling, respectively. However, the maximum surface stress may exceed the material yield strength during an emergency braking, which may cause a plastic damage accumulation in a brake disk without cooling. The simulation results are consistent with the experimental results well.

Sustainable Biocomposites Materials for Automotive Brake Pad Application:An Overview

Research into converting waste into viable eco-friendly products has gained global concern.Using natural fibres and pulverized metallic waste becomes necessary to reduce noxious environmental emissions due to indiscriminately occupying the land.This study reviews the literature in the broad area of green composites in search of materials that can be used in automotive brake pads.Materials made by biocomposite,rather than fossil fuels,will be favoured.A database containing the tribo-mechanical performance of numerous potential components for the future green composite was established using the technical details of bio-polymers and natural reinforcements.The development of materials with diverse compositions and varying proportions is now conceivable,and these materials can be permanently connected in fully regulated processes.This explanation demonstrates that all of these variables affect friction coefficient,resistance to wear from friction and high temperatures,and the operating life of brake pads to varying degrees.In this study,renewable materials for the matrix and reinforcement are screened to determine which have sufficient strength,coefficient of friction,wear resistance properties,and reasonable costs,making them a feasible option for a green composite.The most significant,intriguing,and unusual materials used in manufacturing brake pads are gathered in this review,which also analyzes how they affect the tribological characteristics of the pads.

Tribological properties and thermal-stress analysis of C/C-SiC composites during braking

The tribological properties and thermal-stress behaviors of C/C-SiC composites during braking were investigated aiming to simulate braking tests of high-speed trains. The temperature and structural fields of C/C-SiC composites during braking were fully coupled and simulated with ANSYS software. The results of tribological tests indicated that the C/C-SiC composites showed excellent static friction coefficient (0.68) and dynamic friction coefficient (average value of 0.36). The highest temperature on friction surface was 445℃. The simulated temperature field showed that the highest temperature which appeared on the friction surface during braking was about 463℃. Analysis regarding thermal-stress field showed that the highest thermal-stress on friction surface was 11.5 MPa. The temperature and thermal-stress distributions on friction surface during braking showed the same tendency.

Pressure-tracking control of a novel electro-hydraulic braking system considering friction compensation

This work presents an integrated pressure-tracking controller for a novel electro-hydraulic brake(EHB) system considering friction and hydraulic disturbances. To this end, a mathematical model of an EHB system, consisting of actuator and hydraulic sub-systems, is derived for describing the fundamental dynamics of the system and designing the controller. Due to sensor inaccuracy and measurement noise, a Kalman filter is constructed to estimate push rod stroke for generating desired master cylinder pressure. To improve pressure-tracking accuracy, a linear friction model is generated by linearizing the nonlinear Tustin friction model, and the unmodeled friction disturbances are assumed unknown but bounded. A sliding mode controller is designed for compensating friction disturbances, and the stability of the controller is investigated using the Lyapunov method. The performance of the proposed integrated controller is evaluated with a hardware-in-the-loop(HIL) test platform equipped with the EHB prototype. The test results demonstrate that the EHB system with the proposed integrated controller not only achieves good pressure-tracking performance, but also maintains robustness to friction disturbances.

STUDY ON THE SiC_p./Al-ALLOY COMPOSITE AUTOMOTIVE BRAKE ROTORS

The SiCp/Al-alloy composite front brake rotors designed for Shanghai Santana cars were prepared by semi-solid stirring+liquid forging process. The composite brake rotors were subjected to dynamometer tests on a SCHENCK brake testing system, referring to TL110 standard of VOLKSWAGEN Co. The friction coefficient and thermal response during fade testing and the wear performance of the composite rotors were studied as the functions of various parameters such as braking pressures, initial speeds, initial temperatures, torque and decelerations, and were compared with those of conventional cast iron rotors. The results show that the properties of the composite rotors can achieve the requirements of commercial cast iron rotors. The results also show that the friction coefficients of the composite rotors under different braking conditions are within the deviation band specified by the TL110 standard, and the temperature rise of composite rotors is lower than that of cast iron rotors at the end of each fade stop. The wear resistance of composite rotors is higher than that of cast iron rotors. The friction mechanism and wear mechanism were analyzed.

Preparation and characteristics of C/C composite brake disc by multi-cylindrical chemical vapor deposition processes

The C/C composite brake discs were prepared by tri-cylindrical chemical vapor deposition （CVD） process. The optimum processing parameters were as follows： deposition temperature was 830 - 930 ℃, the gas- flow rates of N2 and propylene were 4.8 - 5.2 m^3/h and 5.8 - 6.2 m^3/h, respectively, the furnace pressure was 4.5 - 5.5 kPa and the deposition time was 200 h. The effects of processing parameters on the densified rates, thermal-physical property and mechanical performance of C/C composite brake discs were studied. The results show that density, heat conductivity, bend strength and abrasion ratio of the multi-cylindrica brake discs are 1. 02 - 1. 78 g/cm^3 , 31 W/（m·K）, 114 MPa and 7μm/s, respectively, which are approximately similar to those of the singlecylindrical ones. The gas tlow rate has no relation to the number of the cylinder and furnace loading. The utilization ratio of carbon can be improved by multi-cylinder CVD process without changing the characteristics of brake disc.

Raman spectroscopy investigation of structural and textural change in C/C composites during braking

The microstructure and texture of C/C composites with a resin-derived carbon, a rough laminar （RL） pyrocarbon and a smooth laminar pyrocarbon, before and after braking tests, were investigated by Raman spectroscopy. The full width at half maximum （FWHM） of the D-band indicates the amount of defects in the in-plane lattice, while the G-to-D band intensity （peak area） ratios （lC/ID） is used to evaluate the degree of graphitization. The results show that the FWHM of D-band of sample with RL pyrocarbon changes greatly from 36 cm-1 to 168 cm 1 after braking tests, which indicates that a large number of lattice defects are produced on its wear surface. However, the graphitization degree of resin-derived carbon sample rises significantly, because the IC/1D increases from 0.427 to 0.928. Braking tests under normal loading conditions, involving high temperature and high pressure, produce a lot of lattice defects on the wear surface, and induce the graphitization of the surface. Sample with RL pyrocarbon having a low hardness is easy to deform, and has the most lattice defects on the wear surface after braking. While raw materials with resin-derived carbon have the lowest graphitization degree which rises greatly during braking.

Tribological characteristics of C/C-SiC braking composites under dry and wet conditions

C/C-SiC braking composites,based on reinforcement of carbon fibers and matrices of carbon and silicon carbide,were fabricated by warm compaction and in situ reaction process.The tribological characteristics of C/C-SiC braking composites under dry and wet conditions were investigated by means of MM-1000 type of friction testing machine.The influence of dry and wet conditions on the tribological characteristics of the C/C-SiC composites was ascertained.Under dry condition,C/C-SiC braking composites show superior tribological characteristics,including high coefficient of friction (0.38),good abrasive resistance (thickness loss is 1.10 μm per cycle) and steady breaking.The main wear mechanism is plastic deformation and abrasion caused by plough.Under wet condition,frictional films form on the worn surface.The coefficient of friction (0.35) could maintain mostly,and the thickness loss (0.70 μm per cycle) reduces to a certain extent.Furthermore,braking curves are steady and adhesion and oxidation are the main wear mechanisms.

A New Type of Automotive Braking Actuator for Decentralized Electro-hydraulic Braking System

This paper presents a new type of automotive braking actuator for a kind of brake-by-wire system called decentralized electro-hydraulic braking system( DEHB) to replace the traditional automobile braking system. The actuator of this system is driven by an electrical motor instead of the conventional vacuum booster to make the brake pressure be linearity controlled quickly. Therefore,the system has the advantages of quick response speed,good control performance and simple structure. Firstly,an overview of the actuator and the whole DEHB system is shown. Secondly,the possibility of this new kind of actuator working for the system is ensured based on some braking theories. Thirdly,the appropriate dynamic simulations are done to get some results to show the relations of different parameters and the effect of braking. Eventually,the proper parameters are determined to build a test bench which shows that DEHB system can achieve the maximum pressure of 13 MPa within 100 ms after parametric optimization,and meanwhile,the actuator is able to reduce pressure quickly after maintaining high pressure. All of the bench test results can meet with the design requirements and real demand of vehicle and this actuator may improve vehicle braking effect in the future. Besides,this actuator can be widely applied to the regenerative braking system because of its linear braking performance.

Analysis of a Cashew Shell and Fly Ash Rich Brake Liner Composite Material

Hybrid materials collected from organic and inorganic sources,which are traditionally used as brake lining materials,generally include fly ash,cashew shell powder,phenolic resins,aluminium wool,barites,lime powder,carbon powder and copper powder.The present research focuses on the specific effects produced by fly ash and aims to provide useful indications for the replacement of asbestos due to the health hazards caused by the related fibers.Furthermore,the financial implications related to the use of large-volume use of fly ash,lime stone and cashew shell powder,readily available in most countries in the world,are also discussed.It is shown that many manufacturing and automotive industries,which are currently experiencing difficulties in meeting the increasing demand for brake lining material,may take advantage from the proposed solution.

Investigation into precision engineering design and development of the next-generation brake discs using Al/SiC metal matrix composites

Substantially lightweight brake discs with high wear resistance are highly desirable in the automotive industry.This paper presents an investigation of the precision-engineering design and development of automotive brake discs using nonhomogeneous Al/SiC metal-matrixcomposite materials.The design and development are based on modeling and analysis following stringent precision-engineering principles,i.e.,brake-disc systems that operate repeatably and stably over time as enabled by precision-engineering design.The design and development are further supported by tribological experimental testing and finite-element simulations.The results show the industrial feasibility of the innovative design approach and the application merits of using advanced metal-matrix-composite materials for next-generation automotive and electric vehicles.

Stability of Composite Braking Produced by Retarder and Braking System

In order to evaluate the effects of the retarder on the braking stability quantitatively, an adhesion coefficient model is built for the composite braking produced by the retarder and the service braking system. The stability of composite braking is evaluated by using the model and the standard ECE R13. The evaluation results show that the composite braking stability decreases gradually with the increase of the retarder's braking force. To improve the stability, the braking force distribution of the service braking system is adjusted according to the position relationship among the braking force distribution line of the service braking system, the generalized braking force distribution line and the generalized I curve, and the constraints in ECE R13. The simulation results show that the composite braking stability can be improved significantly.

Research on the Control Method of Electromechanical Composite Brake Based on Electric Wheel Drive Vehicle

Facing the increasingly serious environmental pollution and oil crisis,the development of automobile industry is facing a very serious challenge.For the sustainable development of automobile industry,the electric vehicle using motor as driving equipment can realize“pollution-free”,which has become the focus of automobile research and development in many countries.In the research and development of electric vehicles,the electric vehicles driven by electric wheels have attracted the attention of all walks of life because of their ideal control characteristics and broad application prospects.In this paper,the electric wheel drive vehicle as the research object,the electromechanical composite brake control system is studied and analyzed.

Application Research on Self-healing Technology with Microcapsules for Automobile Brake Pad

In order to improve the performance of non-asbestos composite auto brake pads that are composed of matrix resin, reinforced material and fillers, a novel method with new technology of self-heal microcapsules was proposed. Nano reinforced fillers＇ effects were also considered in the experiment project. Five recipe designs for new composite auto brake pads were carried out and cor-responding samples were prepared as well. The friction coefficient and wearing properties at certain temperature, impact intensity and hardness were comparatively studied. Investigations indicate that properties of such composite auto brake pads meet the requirements of the national standards while microcapsule＇s weight content varies from 5.5wt%-1.09wt% of matrix resin and microcapsule＇s loca-tion varies in the pads. Nano reinforced fillers have the effects of increasing composites＇ impact in-tensity and hardness. Application of self-healing microcapsules in auto brake pads is feasible.

Resin Matrix Brake Materials Reinforced by Nano-Al_2O_3 for Mining Equipment

To verify the effect of Al_2O_3 particle content and size as an abrasive on resin matrix friction materials for mining equipment, the tribological performance of friction materials was studied by using a blockon-ring tribotester over a wide range of applied load and sliding speed. The testing conditions simulated brake conditions of mining equipment. The antiwear property of nano-Al_2O_3 was superior to that of micro-Al_2O_3 for friction materials. The friction coefficients of specimens increased with the increase of nano-Al_2O_3 content. The wear rates decreased with increasing nano-Al_2O_3 content. The wear rates of specimens containing nano-Al_2O_3 was about 2-8 times lower than that of specimen with micro-Al2O3. The specimen with 10.5 vol% nano-Al_2O_3 showed the best tribological properties. The wear mechanism of specimens with nano-Al_2O_3 was abrasive wear and plastic deformation.

考虑道路识别的四驱电动汽车再生制动策略

为了充分利用路面附着条件分配再生制动力,提高制动能量回收率,根据双电动机四驱结构电动汽车复合制动系统的特点,对其制动能量回收控制策略进行了研究.分析了驱动轮与地面附着特性,设计了道路识别器来计算每个轮胎与当前路面之间的峰值附着系数,并使用模糊控制策略确定每个车轮与8种道路的滑移率和附着利用率的相似输入.根据双电动机外部特性的制动力分配关系,提出了使更多制动能量回馈给电池的策略.结果表明:制动强度为0.3时,能量回收率为65.55%,具有较高的回收效率.

轻量化高速列车制动盘材料-结构研究进展

400 km/h高速列车紧急制动的强热负荷,导致制动盘温升高、温度分布梯度大和热衰减强,已超出钢质制动盘能载极限,开发耐高温强耐磨的制动盘材料,同时提升制动盘通风散热能力成为制动技术发展瓶颈。综述高速制动盘材料从高强度铸钢和锻钢、轻量化铝基复合材料至耐高温耐磨碳陶复合材料和表面改性技术发展历程,随着碳陶复合材料的台架试验和表面改性技术的摩擦磨损试验研究的深化,表面改性轻质复合材料是制动盘材料未来发展方向。概述通风制动盘内部散热层散热筋结构形貌优化、摩擦层表面耐磨性能改善的发展现状,内部散热筋由直通道设计逐渐演化为弯曲、支柱以及分形通道,镂空结构能更好地加速空气流动提高散热;表面摩擦层引入打孔或划线,更易于摩擦粉尘的抛离从而稳定摩擦因数,保持制动效果;但复杂通风导流结构和打孔划线增加了制备工艺的难度,提出高速制动盘结构构型设计需要综合材料热力学性能、制备工艺及耐热耐磨需求,形成材料-结构-功能—体化设计理念,为实现更高速的制动盘优化设计提供参考。

电动装载机电液复合制动协同控制策略研究

针对电动装载机的电液复合制动系统,为满足多工况制动需求以及保障制动安全性,本文提出了一种基于再生制动自由行程液压制动阀的电动装载机液压制动系统。结合电动装载机的理想前后轮制动力分配曲线以及制动意图识别得到的制动强度,制定了制动强度与整车制动力矩需求的分配曲线;为进一步提高再生制动力与液压制动力分配的协调性,同时兼顾制动能量回收效率,提出了一种基于行走再生制动和液压制动的电液复合制动协同控制策略,降低了整车总制动力矩波动,保证了制动模式切换的平顺性。最后,搭建了基于AMESim-Matlab/Simulink联合仿真模型,并搭建试验样机,验证了电动装载机复合制动协同控制策略的可行性,结果表明,该系统能量回收效率可达71.6%,制动回收率可达44.5%,一个工作循环实现节能7.6%,说明本文提出的控制策略具有良好的制动性能和能量回收效率。

Frictional response of a novel C/C-ZrB_(2)-ZrC-SiC composite under simulated braking

A novel braking material,C/C-ZrB_(2)-ZrC-SiC carbon fibre-reinforced hybrid ceramic matrix composite,was prepared by chemical vapour infiltration and polymeric precursor infiltration and pyrolysis.Investigation of the microstructure of C/C-ZrB_(2)-ZrC-SiC composite showed the homogenous dispersion of three-phase ceramic as the matrix.The frictional properties of the hybrid C/C-ZrB_(2)-ZrC-SiC ceramic matrix composite were measured by a disk-on-disk type dynamometer under dry and wet conditions to simulate the normal landing state of aircraft brake disk friction pairs.C/C-ZrB_(2)-ZrC-SiC ceramic matrix composite has a higher and more stable friction coefficient under wet condition than under dry condition,indicating that the composite has better performance compared with C/C or C/C-SiC braking materials.

先进陶瓷-金属复合材料在汽车制动系统应用研究

本文基于先进陶瓷-金属复合材料在汽车制动系统的应用前景,开展了教学方法的探索与实践。以培养适应社会发展的高水平人才为目标,通过及时优化教学方法来满足社会对人才的新需求。研究了先进复合材料在未来汽车领域的应用前景,重点分析先进材料在汽车制动系统的需求。通过真空热压烧结技术制备了性能优异的陶瓷-金属复合材料,根据制动系统对材料性能的要求,重点研究了复合材料的弯曲强度性能和摩擦磨损性能。引导学生以实际应用为驱动力,把学习与工程实践相联系,更好地掌握材料制备和性能优化的基本原理和方法。