Electrochemical hydrogen storage characteristics of nanocrystalline and amorphous Mg_2Ni-type alloys prepared by melt-spinning

The nanocrystalline and amorphous Mg2Ni-type alloys with nominal compositions of Mg2Ni1-xMnx （x=0, 0.1, 0.2, 0.3, 0.4） were synthesized by melt-spinning technique. The spun alloy ribbons with a continuous length, a thickness of about 30 μm and a width of about 25 mm are obtained. The structures of the as-spun alloy ribbons were characterized by XRD and HRTEM. The electrochemical hydrogen storage characteristics of the as-spun alloy ribbons were measured by an automatic galvanostatic system. The electrochemical impedance spectrums （EIS） were plotted by an electrochemical workstation. The hydrogen diffusion coefficients （D） in the alloys were calculated by virtue of potential-step measurement. The results show that all the as-spun （x=0） alloys hold a typical nanocrystalline structure, whereas the as-spun （x=0.4） alloy displays a nanocrystalline and amorphous structure, confirming that the substitution of Mn for Ni facilitates the glass formation in the Mg2Ni-type alloy. The substitution of Mn for Ni significantly improves the electrochemical hydrogen storage performances of the alloys, involving the discharge capacity and the electrochemical cycle stability. With an increase in the amount of Mn substitution from 0 to 0.4, the discharge capacity of the as-spun （20 m/s） alloy increases from 96.5 to 265.3 mA·h/g, and its capacity retaining rate （S20） at the 20th cycle increases from 31.3% to 70.2%. Furthermore, the high rate dischargeability （HRD）, electrochemical impedance spectrum and potential-step measurements all indicate that the electrochemical kinetics of the alloy electrodes first increases then decreases with raising the amount of Mn substitution.

Effect of Ni,Fe and Fe-Ni alloy catalysts on the synthesis of metal contained carbon nano-onions and studies of their electrochemical hydrogen storage properties

Three types of carbon nano-onions（CNOs） including Ni@CNOs.Fe3C@CNOs and Fe0.64Ni0.36@CNOs nanoparticles have been synthesized by catalytic decomposition of methane at 850 ℃ using nickel,iron and iron-nickel alloy catalysts.Comparative and systematic studies have been carried out on the morphology,structural characteristics and graphitic crystallinity of these CNOs products.Furthermore,the electrochemical hydrogen storage properties of three types of CNOs have been investigated.Measurements show that the Ni@CNOs have the highest discharge capacity of 387.2 mAh/g,coiTesponding to a hydrogen storage of 1.42%.This comparison study shows the advantages of each catalyst in the growth of CNOs.enabling the controllable synthesis and tuning the properties of CNOs by mediating different metals and their alloy for using in the fuel cell system.

Improved electrochemical hydrogen storage properties of Mg-Y thin films as a function of substrate temperature

Pd-capped Mg78Y22 thin films have been prepared by direct current magnetron co-sputtering system at different substrate temperatures and their electrochemical hydrogen storage properties have been investigated.It is found that rising substrate temperature to 60 ℃ can coarsen the surface of thin film,thus facilitating the diffusion of hydrogen atoms and then enhancing its discharge capacity to 1725 mAh·g-1.Simultaneously,the cyclic stability is effectively improved due to the increased adhesion force between film and substrate as a function of temperature.In addition,the specimen exhibits a very long and flat discharge plateau at about —0.67 V,at which nearly 60%of capacity is maintained.The property is favorable for the application in metal hydride/nickel secondary batteries.The results indicate that rising optimal substrate temperature has a beneficial effect on the electrochemical hydrogen storage of Mg-Y thin films.

Towards electrochemical hydrogen storage in liquid organic hydrogen carriers via proton-coupled electron transfers

Green hydrogen is identified as one of the prime clean energy carriers due to its high energy density and a zero emission of CO_(2).A possible solution for the transport of H_(2)in a safe and low-cost way is in the form of liquid organic hydrogen carriers(LOHCs).As an alternative to loading LOHC with H_(2)via a two-step procedure involving preliminary electrolytic production of H_(2)and subsequent chemical hydrogenation of the LOHC,we explore here the possibility of electrochemical hydrogen storage(EHS)via conversion of proton of a proton donor into a hydrogen atom involved in covalent bonds with the LOHC(R)via a protoncoupled electron transfer(PCET)reaction:2nH^(+)+2ne^(-)+Rox■n H_(2)^(0)Rred.We chose 9-fluorenone/fluorenol(Fnone/Fnol)conversion as such a model PCET reaction.The electrochemical activation of Fnone via two sequential electron transfers was monitored with in-situ and operando spectroscopies in absence and in presence of different alcohols as proton donors of different reactivity,which enabled us to both quantify and get the mechanistic insight on PCET.The possibility of hydrogen extraction from the loaded carrier molecule was illustrated by chemical activation.

Structure and electrochemical hydrogen storage characteristics of Ce-Mg-Ni-based alloys synthesized by mechanical milling

The substituting Mg with Ni and milling as-cast alloy with Ni were adopted to obtain nanocrystalline/amorphous CeMgnNi＋x wt.%Ni（x=100,200） alloys and promote the electrochemical hydrogen storage performances of CeMg_（12）-type alloys.Analyzing the structural features of the alloys provided a mechanism for ameliorating the electrochemical hydrogen storage properties.The electrochemical tests demonstrated that all the alloys just needed one cycle to be activated.Rising Ni proportion had an obvious role on charge-discharge reaction.The discharge capacities of the as-milled（60 h） alloys increased sharply from 182.0 mAh/gfor x=100 alloy to 1010.2 mAh/gfor x=200 alloy at current density of 60 mAh/g.Furthermore,milling time largely determined the performances of electrochemical reaction.The discharge capacity continued to grow along with prolonging milling time,while the cycle stability obviously decreased for x=100 alloy,and first declined and then augmented for the x=200 alloy with milling time extending.In addition,there was an optimal value with milling time varying for the high rate discharge abilities（HRD）,which was 80.3%for x=100 alloys and 86.73%for x=200,respectively.

Electrochemical hydrogen storage performances of the nanocrystalline and amorphous(Mg_(24)Ni_(10)Cu_2)_(100–x)Nd_x(x=0–20) alloys applied to Ni-MH battery

Melt spinning technology was used to prepare the Mg2 Ni-type（Mg24 Ni10 Cu2）100–x Ndx（x=0,5,10,15,20） alloys in order to obtain a nanocrystalline and amorphous structure.The effects of Nd content and spinning rate on the structures and electrochemical hydrogen storage performances of the alloys were investigated.The structure characterizations of X-ray diffraction（XRD）,transmission electron microscopy（TEM） and scanning electron microscopy（SEM） linked with energy dispersive spectroscopy（EDS） revealed that the as-spun Nd-free alloy displayed an entire nanocrystalline structure,whereas the as-spun Nd-added alloys held a nanocrystalline and amorphous structure and the degree of amorphization visibly increased with the rising of Nd content and spinning rate,suggesting that the addition of Nd facilitated the glass forming of the Mg2 Ni-type alloy.The electrochemical measurements indicated that the addition of Nd and melt spinning improved the electrochemical hydrogen storage performances of the alloys significantly.The discharge capacities of the as-cast and spun alloys exhibited maximum values when Nd content was x=10,which were 86.4,200.5,266.3,402.5 and 452.8 mAh/g corresponding to the spinning rate of 0（As-cast was defined as the spinning rate of 0 m/s）,10,20,30 and 40 m/s,respectively.The cycle stability（S20,the capacity maintain rate at 20thcycle） of the as-cast alloy always rose with the increasing of Nd content,and those of the as-spun alloys exhibited the maximum values for Nd content x=10,which were 77.9%,83.4% 89.2% and 89.7%,corresponding to the spinning rate of 10,20,30 and 40 m/s,respectively.

Effect of Nitrogen and Sulfur Co‑Doped Graphene on the Electrochemical Hydrogen Storage Performance of Co_(0.9)Cu_(0.1)Si Alloy

Co_(0.9)Cu_(0.1)Si alloy was prepared by mechanical alloying method.Nitrogen-doped graphene(NG)and nitrogen–sulfur codoped graphene(NSG)were prepared by hydrothermal method.5 wt%graphene oxide,NG and NSG were doped into Co_(0.9)Cu_(0.1)Si alloy,respectively,by ball milling to improve the electrochemical hydrogen storage performance of the composite material.X-ray diffraction and scanning electron microscopy were used to characterize the structure and morphology of the composite material,and the LAND battery test system and three-electrode battery system were used to test the electrochemical performance of the composite material.The composite material showed better discharge capacity and better cycle stability than the pristine alloy.In addition,in order to study the optimal ratio of NSG,3%,5%,7%and 10%of NSG were doped into Co_(0.9)Cu_(0.1)Si alloy,respectively.Co_(0.9)Cu_(0.1)Si alloy doped with 5%NSG had the best performance among all the samples.The best discharge capacity was 580.1 mAh/g,and its highest capacity retention rate was 64.1%.The improvement in electrochemical hydrogen storage performance can be attributed to two aspects.On the one hand,the electrocatalytic performance of graphene is improved by co-doping nitrogen and sulfur,on the other hand,graphene has excellent electrical conductivity.

Structure and electrochemical properties of LaMgNi4-xCox(x=0-0.8)hydrogen storage electrode alloys

LaMgNi（4-x）Cox（x = 0-0.8） electrode alloys used for MH/Ni batteries were prepared by induction melting. The structures and electrochemical hydrogen storage properties of the alloys were investigated in detail.X-ray diffraction（XRD） and scanning electron microscopy（SEM） analysis show that LaMgNi4 phase and LaNi5 phase are obtained. The lattice parameters of the two phases increase first and then decrease with Co content increasing.The electrochemical properties of the alloy electrodes were measured by means of simulated battery tests. Results show that the addition of Co does not change the discharge voltage plateau of the alloy electrodes. However, the maximum discharge capacity increases from 319.9 mAh·g^-1（x = 0）to 347.5 mAh·g^-1（x = 0.4） and then decreases to331.7 mAh·g^-1（x = 0.8）. The effects of Co content on electrochemical kinetics of the alloy electrodes were also performed. The high rate dischargeability（HRD） first increases and then decreases with Co content increasing and reaches the maximum value（95.0 %） when x = 0.4. Test results of the electrochemical impedance spectra（EIS）,potentiodynamic polarization curves and constant potential step measurements of the alloy electrodes all demonstrate that when Co content is 0.4 at%, the alloy exhibits the best comprehensive electrochemical properties.

Effect of annealing treatment on hydrogen storage properties of La-Ti-Mg-Ni-based alloy

The present study dealt with investigations on the effects of annealing on the hydrogen storage properties of La 1.6 Ti 0.4 MgNi 9 alloys.The experimental alloys were prepared by magnetic levitation melting followed by annealing treatment.For La 1.6 Ti 0.4 MgNi 9 alloys,LaNi 5,LaNi 3 and LaMg 2 Ni 9 were the main phases,Ti 2 Ni phase appeared at 900℃.Annealing not only enhanced the maximum and effective hydrogen storage capacity,improved the hydrogen absorption/desorption kinetics,but also increased the discharge capacity.The cyclic stability had been improved markedly by annealing,e.g.,when the discharge capacity reduced to 60% of maximum discharge capacity,the charge/discharge cycles increased from 66（as-cast） to 89（annealed at 800℃） and 127 times（annealed at 900℃）.La 1.6 Ti 0.4 MgNi 9 alloy annealed at 900℃ exhibited better electrochemical properties compared to the other two alloy electrodes.