Electrode/Electrolyte Optimization‑Induced Double‑Layered Architecture for High‑Performance Aqueous Zinc‑(Dual)Halogen Batteries

Aqueous zinc-halogen batteries are promising candidates for large-scale energy storage due to their abundant resources,intrinsic safety,and high theoretical capacity.Nevertheless,the uncontrollable zinc dendrite growth and spontaneous shuttle effect of active species have prohibited their practical implementation.Herein,a double-layered protective film based on zinc-ethylenediamine tetramethylene phosphonic acid(ZEA)artificial film and ZnF2-rich solid electrolyte interphase(SEI)layer has been successfully fabricated on the zinc metal anode via electrode/electrolyte synergistic optimization.The ZEA-based artificial film shows strong affinity for the ZnF2-rich SEI layer,therefore effectively suppressing the SEI breakage and facilitating the construction of double-layered protective film on the zinc metal anode.Such double-layered architecture not only modulates Zn2+flux and suppresses the zinc dendrite growth,but also blocks the direct contact between the metal anode and electrolyte,thus mitigating the corrosion from the active species.When employing optimized metal anodes and electrolytes,the as-developed zinc-(dual)halogen batteries present high areal capacity and satisfactory cycling stability.This work provides a new avenue for developing aqueous zinc-(dual)halogen batteries.

Aligned Ion Conduction Pathway of Polyrotaxane‑Based Electrolyte with Dispersed Hydrophobic Chains for Solid‑State Lithium–Oxygen Batteries

A critical challenge hindering the practical application of lithium–oxygen batteries(LOBs)is the inevitable problems associated with liquid electrolytes,such as evaporation and safety problems.Our study addresses these problems by proposing a modified polyrotaxane(mPR)-based solid polymer electrolyte(SPE)design that simultaneously mitigates solvent-related problems and improves conductivity.mPR-SPE exhibits high ion conductivity(2.8×10^(−3)S cm^(−1)at 25℃)through aligned ion conduction pathways and provides electrode protection ability through hydrophobic chain dispersion.Integrating this mPR-SPE into solid-state LOBs resulted in stable potentials over 300 cycles.In situ Raman spectroscopy reveals the presence of an LiO_(2)intermediate alongside Li_(2)O_(2)during oxygen reactions.Ex situ X-ray diffraction confirm the ability of the SPE to hinder the permeation of oxygen and moisture,as demonstrated by the air permeability tests.The present study suggests that maintaining a low residual solvent while achieving high ionic conductivity is crucial for restricting the sub-reactions of solid-state LOBs.

Advancements and Challenges in Organic–Inorganic Composite Solid Electrolytes for All‑Solid‑State Lithium Batteries

To address the limitations of contemporary lithium-ion batteries,particularly their low energy density and safety concerns,all-solid-state lithium batteries equipped with solid-state electrolytes have been identified as an up-and-coming alternative.Among the various SEs,organic–inorganic composite solid electrolytes(OICSEs)that combine the advantages of both polymer and inorganic materials demonstrate promising potential for large-scale applications.However,OICSEs still face many challenges in practical applications,such as low ionic conductivity and poor interfacial stability,which severely limit their applications.This review provides a comprehensive overview of recent research advancements in OICSEs.Specifically,the influence of inorganic fillers on the main functional parameters of OICSEs,including ionic conductivity,Li+transfer number,mechanical strength,electrochemical stability,electronic conductivity,and thermal stability are systematically discussed.The lithium-ion conduction mechanism of OICSE is thoroughly analyzed and concluded from the microscopic perspective.Besides,the classic inorganic filler types,including both inert and active fillers,are categorized with special emphasis on the relationship between inorganic filler structure design and the electrochemical performance of OICSEs.Finally,the advanced characterization techniques relevant to OICSEs are summarized,and the challenges and perspectives on the future development of OICSEs are also highlighted for constructing superior ASSLBs.

Sulfolane‑Based Flame‑Retardant Electrolyte for High‑Voltage Sodium‑Ion Batteries

Sodium-ion batteries hold great promise as next-generation energy storage systems.However,the high instability of the electrode/electrolyte interphase during cycling has seriously hindered the development of SIBs.In particular,an unstable cathode–electrolyte interphase(CEI)leads to successive electrolyte side reactions,transition metal leaching and rapid capacity decay,which tends to be exacerbated under high-voltage conditions.Therefore,constructing dense and stable CEIs are crucial for high-performance SIBs.This work reports localized high-concentration electrolyte by incorporating a highly oxidation-resistant sulfolane solvent with non-solvent diluent 1H,1H,5H-octafluoropentyl-1,1,2,2-tetrafluoroethyl ether,which exhibited excellent oxidative stability and was able to form thin,dense and homogeneous CEI.The excellent CEI enabled the O3-type layered oxide cathode NaNi_(1/3)Mn_(1/3)Fe_(1/3)O_(2)(NaNMF)to achieve stable cycling,with a capacity retention of 79.48%after 300 cycles at 1 C and 81.15%after 400 cycles at 2 C with a high charging voltage of 4.2 V.In addition,its nonflammable nature enhances the safety of SIBs.This work provides a viable pathway for the application of sulfolane-based electrolytes on SIBs and the design of next-generation high-voltage electrolytes.

Porous Organic Cage‑Based Quasi‑Solid‑State Electrolyte with Cavity‑Induced Anion‑Trapping Effect for Long‑Life Lithium Metal Batteries

Porous organic cages(POCs)with permanent porosity and excellent host–guest property hold great potentials in regulating ion transport behavior,yet their feasibility as solid-state electrolytes has never been testified in a practical battery.Herein,we design and fabricate a quasi-solid-state electrolyte(QSSE)based on a POC to enable the stable operation of Li-metal batteries(LMBs).Benefiting from the ordered channels and cavity-induced anion-trapping effect of POC,the resulting POC-based QSSE exhibits a high Li+transference number of 0.67 and a high ionic conductivity of 1.25×10^(−4) S cm^(−1) with a low activation energy of 0.17 eV.These allow for homogeneous Li deposition and highly reversible Li plating/stripping for over 2000 h.As a proof of concept,the LMB assembled with POC-based QSSE demonstrates extremely stable cycling performance with 85%capacity retention after 1000 cycles.Therefore,our work demonstrates the practical applicability of POC as SSEs for LMBs and could be extended to other energy-storage systems,such as Na and K batteries.

Molecule‑Level Multiscale Design of Nonflammable Gel Polymer Electrolyte to Build Stable SEI/CEI for Lithium Metal Battery

The risk of flammability is an unavoidable issue for gel polymer electrolytes(GPEs).Usually,flameretardant solvents are necessary to be used,but most of them would react with anode/cathode easily and cause serious interfacial instability,which is a big challenge for design and application of nonflammable GPEs.Here,a nonflammable GPE(SGPE)is developed by in situ polymerizing trifluoroethyl methacrylate(TFMA)monomers with flame-retardant triethyl phosphate(TEP)solvents and LiTFSI–LiDFOB dual lithium salts.TEP is strongly anchored to PTFMA matrix via polarity interaction between-P=O and-CH_(2)CF_(3).It reduces free TEP molecules,which obviously mitigates interfacial reactions,and enhances flame-retardant performance of TEP surprisingly.Anchored TEP molecules are also inhibited in solvation of Li^(+),leading to anion-dominated solvation sheath,which creates inorganic-rich solid electrolyte interface/cathode electrolyte interface layers.Such coordination structure changes Li^(+)transport from sluggish vehicular to fast structural transport,raising ionic conductivity to 1.03 mS cm^(-1) and transfer number to 0.41 at 30℃.The Li|SGPE|Li cell presents highly reversible Li stripping/plating performance for over 1000 h at 0.1 mA cm^(−2),and 4.2 V LiCoO_(2)|SGPE|Li battery delivers high average specific capacity>120 mAh g^(−1) over 200 cycles.This study paves a new way to make nonflammable GPE that is compatible with Li metal anode.

Recent Advances in Nanoengineering of Electrode-Electrolyte Interfaces to Realize High-Performance Li-Ion Batteries

A suitable interface between the electrode and electrolyte is crucial in achieving highly stable electrochemical performance for Li-ion batteries,as facile ionic transport is required.Intriguing research and development have recently been conducted to form a stable interface between the electrode and electrolyte.Therefore,it is essential to investigate emerging knowledge and contextualize it.The nanoengineering of the electrode-electrolyte interface has been actively researched at the electrode/electrolyte and interphase levels.This review presents and summarizes some recent advances aimed at nanoengineering approaches to build a more stable electrode-electrolyte interface and assess the impact of each approach adopted.Furthermore,future perspectives on the feasibility and practicality of each approach will also be reviewed in detail.Finally,this review aids in projecting a more sustainable research pathway for a nanoengineered interphase design between electrode and electrolyte,which is pivotal for high-performance,thermally stable Li-ion batteries.

Synergistic Coupling of Sulfide Electrolyte and Integrated 3D FeS_(2)Electrode Toward Long-Cycling All-Solid-State Lithium Batteries

FeS_(2)cathode is promising for all-solid-state lithium batteries due to its ultra-high capacity,low cost,and environmental friendliness.However,the poor performances,induced by limited electrode-electrolyte interface,severe volume expansion,and polysulfide shuttle,hinder the application of FeS_(2)in all-solid-state lithium batteries.Herein,an integrated 3D FeS_(2)electrode with full infiltration of Li6PS5Cl sulfide electrolytes is designed to address these challenges.Such a 3D integrated design not only achieves intimate and maximized interfacial contact between electrode and sulfide electrolytes,but also effectively buffers the inner volume change of FeS_(2)and completely eliminates the polysulfide shuttle through direct solid-solid conversion of Li2S/S.Besides,the vertical 3D arrays guarantee direct electron transport channels and horizontally shortened ion diffusion paths,endowing the integrated electrode with a remarkably reduced interfacial impedance and enhanced reaction kinetics.Benefiting from these synergies,the integrated all-solid-state lithium battery exhibits the largest reversible capacity(667 mAh g^(-1)),best rate performance,and highest capacity retention of 82%over 500 cycles at 0.1 C compared to both a liquid battery and non-integrated all-solid-state lithium battery.The cycling performance is among the best reported for FeS_(2)-based all-solid-state lithium batteries.This work presents an innovative synergistic strategy for designing long-cycling high-energy all-solid-state lithium batteries,which can be readily applied to other battery systems,such as lithium-sulfur batteries.

Design of multifunctional interfaces on ceramic solid electrolytes for high-performance lithium-air batteries

High-energy-density lithium(Li)–air cells have been considered a promising energy-storage system,but the liquid electrolyte-related safety and side-reaction problems seriously hinder their development.To address these above issues,solid-state Li–air batteries have been widely developed.However,many commonly-used solid electrolytes generally face huge interface impedance inLi–air cells and also showpoor stability towards ambient air/Li electrodes.Herein,we fabricate a differentiating surface-regulated ceramic-based composite electrolyte(DSCCE)by constructing disparately LiI-containing polymethyl methacrylate(PMMA)coating and Poly(vinylidene fluoride-co-hexafluoropropylene)(PVDF-HFP)layer on both sides of Li_(1.5)Al_(0.5)Ge_(1.5)(PO_(4))_(3)(LAGP).The cathode-friendly LiI/PMMA layer displays excellent stability towards superoxide intermediates and also greatly reduces the decomposition voltage of discharge products in Li–air system.Additionally,the anode-friendly PVDF-HFP coating shows low-resistance properties towards anodes.Moreover,Li dendrite/passivation derived from liquid electrolyte-induced side reactions and air/I-attacking can be obviously suppressed by the uniformand compact composite framework.As a result,the DSCCE-based Li–air batteries possess high capacity/low voltage polarization(11,836mAh g^(-1)/1.45Vunder 500mAg^(-1)),good rate performance(capacity ratio under 1000mAg^(-1)/250mAg^(-1) is 68.2%)and longterm stable cell operation(~300 cycles at 750 mA g^(-1) with 750 mAh g^(-1))in ambient air.

Alternative Strategy for Development of Dielectric Calcium Copper Titanate‑Based Electrolytes for Low‑Temperature Solid Oxide Fuel Cells

The development of low-temperature solid oxide fuel cells(LT-SOFCs)is of significant importance for realizing the widespread application of SOFCs.This has stimulated a substantial materials research effort in developing high oxide-ion conductivity in the electrolyte layer of SOFCs.In this context,for the first time,a dielectric material,CaCu_(3)Ti_(4)O_(12)(CCTO)is designed for LT-SOFCs electrolyte application in this study.Both individual CCTO and its heterostructure materials with a p-type Ni_(0.8)Co_(0.15)Al_(0.05)LiO_(2−δ)(NCAL)semiconductor are evaluated as alternative electrolytes in LT-SOFC at 450–550℃.The single cell with the individual CCTO electrolyte exhibits a power output of approximately 263 mW cm^(-2) and an open-circuit voltage(OCV)of 0.95 V at 550℃,while the cell with the CCTO–NCAL heterostructure electrolyte capably delivers an improved power output of approximately 605 mW cm^(-2) along with a higher OCV over 1.0 V,which indicates the introduction of high hole-conducting NCAL into the CCTO could enhance the cell performance rather than inducing any potential short-circuiting risk.It is found that these promising outcomes are due to the interplay of the dielectric material,its structure,and overall properties that led to improve electrochemical mechanism in CCTO–NCAL.Furthermore,density functional theory calculations provide the detailed information about the electronic and structural properties of the CCTO and NCAL and their heterostructure CCTO–NCAL.Our study thus provides a new approach for developing new advanced electrolytes for LT-SOFCs.

Tailoring Electrode–Electrolyte Interface Using an Electron-Deficient Borate-Based Additive in MgTFSI_(2)-MgCl_(2)/DME Electrolyte for Rechargeable Magnesium Batteries

Rechargeable magnesium metal batteries need an electrolyte that forms a stable and ionically conductive solid electrolyte interphase(SEI)on the anodes.Here,we used molecular dynamic simulation,density functional theory calculation,and X-ray photoelectron spectroscopy analysis to investigate the solvation structures and SEI compositions in electrolytes consisting of dual-salts,magnesium bis(trifluoromethanesulfonyl)imide(MgTFSI_(2)),and MgCl_(2),with different additives in 1,2-dimethoxyethane(DME)solvent.We found that the formed[Mg_(3)(μ-Cl)_(4)(DME)mTFSI_(2)](m=3,5)inner-shell solvation clusters in MgTFSI_(2)-MgCl_(2)/DME electrolyte could easily decompose and form a MgO-and MgF_(2)-rich SEI.Such electron-rich inorganic species in the SEI,especially MgF_(2),turned out to be detrimental for Mg plating/stripping.To reduce the MgF_(2)and MgO contents in SEI,we introduce an electron-deficient tri(2,2,2-trifluoroethyl)borate(TFEB)additive in the electrolyte.Mg//Mg cells using the MgTFSI_(2)-MgCl_(2)/DME-TFEB electrolyte could cycle stably for over 400 h with a small polarization voltage of~150 mV.Even with the presence of 800 ppm H_(2)O,the electrolyte with TFEB additive could still preserve its good electrochemical performance.The optimized electrolyte also enabled stable cycling and high-rate capability for Mg//Mo6S8 and Mg//CuS full cells,showing great potential for future applications.

Electrolyte dependence for the electrochemical decarboxylation of medium-chain fatty acids (n-octanoic acid) into fuel on Pt electrode

The deoxygenation of organic acids, important biomass feedstocks and derivatives, to synthesize hydrocarbon products under mild electrochemical conditions, holds significant importance for the production of carbon-neutral biofuels. There is still limited research on the influential factors of the electrochemical decarboxylation reaction of medium-chain fatty acids. In this study, n-octanoic acid (OA) was chosen as the research subject to investigate the electrochemical decarboxylation behavior of OA on a platinum electrode, focusing on the influence of different alkali metal cations (Li^(+), Na^(+), K^(+)), common anions (SO^(4)^(2−), Cl^(−)), and electrolyte pH. It was found that KOH as an electrolyte exhibited the best performance for OA. Possibly, the larger size of K^(+) increased the alkalinity of the electrode surface, facilitating OA deprotonation. LiOH electrolyte reduced the solubility of OA, thereby inhibiting the decarboxylation reaction. SO^(4)^(2−) exhibited a weak promoting effect on the decarboxylation reaction of OA, while Cl^(−) showed no adverse effect although Cl^(−) may adsorb on the electrode surface. Furthermore, unlike short-chain fatty acids, medium-chain OA can only achieve efficient decarboxylation under alkaline conditions due to its solubility properties. This study provides references and foundations for future efforts to enhance the efficiency of electrochemical decarboxylation synthesis of hydrocarbon biofuels from medium-chain fatty acids.

Designing Conformal Electrode-electrolyte Interface by Semi-solid NaK Anode for Sodium Metal Batteries

Solid-state Na metal batteries(SSNBs),known for its low cost,high safety,and high energy density,hold a significant position in the next generation of rechargeable batteries.However,the urgent challenge of poor interfacial contact in solid-state electrolytes has hindered the commercialization of SSNBs.Driven by the concept of intimate electrode-electrolyte interface design,this study employs a combination of NaK alloy and carbon nanotubes to prepare a semi-solid NaK(NKC)anode.Unlike traditional Na anodes,the paintable paste-like NKC anode exhibits superior adhesion and interface compatibility with both current collectors and gel electrolytes,significantly enhancing the intimate contact of electrode-electrolyte interface.Additionally,the filling of SiO_(2)nanoparticles improves the wettability of NaK alloy on gel polymer electrolytes,further achieving a conformal interface contact.Consequently,the overpotential of the NKC symmetric cell is markedly lower than that of the Na symmetric cell when subjected to a long cycle of 300 h.The full cell coupled with Na_(3)V_(3)(PO_(4))_(2)cathodes had an initial discharge capacity of 106.8 mAh·g^(-1)with a capacity retention of 89.61%after 300 cycles,and a high discharge capacity of 88.1 mAh·g^(-1)even at a high rate of 10 C.The outstanding electrochemical performance highlights the promising application potential of the NKC electrode.

Enhanced electrochemical carbon dioxide reduction in membrane electrode assemblies with acidic electrolytes through a silicate buffer layer

The electrochemical reduction of CO_(2)holds considerable promise in combating global climate change while yielding valuable chemical commodities.Membrane electrode assemblies operating within acidic electrolyte have exhibited noteworthy advancements in CO_(2)utilization efficiency,albeit encountering formidable competition from the hydrogen evolution reaction.In our investigation,we introduced a silicate buffer layer,which yielded exceptional outcomes even using strong acid electrolyte.Notably,our approach yielded a CO Faradic efficiency of 90%and reached a substantial current density of 400 mA cm^(-2).Furthermore,our system displayed remarkable stability over a 12-hour duration,and achieved a high single-pass-conversion efficiency of 67%.Leveraging in-situ Raman analysis,we attributed these performance enhancements to the augmented CO_(2)adsorption and localized alkaline environment facilitated by the incorporation of the silicate buffer layer.We think the addition of buffer layer to adjust the microenvironment is essential to achieve high performance and keep stable in acid condition.

High Seebeck Coefficient Thermally Chargeable Supercapacitor with Synergistic Effect of Multichannel Ionogel Electrolyte and Ti_(3)C_(2)T_(x) MXene-Based Composite Electrode

Thermally chargeable supercapacitors can collect low-grade heat generated by the human body and convert it into electricity as a power supply unit for wearable electronics.However,the low Seebeck coefficient and heat-to-electricity conversion efficiency hinder further application.In this paper,we designed a high-performance thermally chargeable supercapacitor device composed of ZnMn_(2)O_(4)@Ti_(3)C_(2)T_(x)MXene composites(ZMO@Ti_(3)C_(2)T_(x) MXene)electrode and UIO-66 metal–organic framework doped multichannel polyvinylidene fluoridehexafluoro-propylene ionogel electrolyte,which realized the thermoelectric conversion and electrical energy storage at the same time.This thermally chargeable supercapacitor device exhibited a high Seebeck coefficient of 55.4 mV K^(−1),thermal voltage of 243 mV,and outstanding heat-to-electricity conversion efficiency of up to 6.48%at the temperature difference of 4.4 K.In addition,this device showed excellent charge–discharge cycling stability at high-temperature differences(3 K)and low-temperature differences(1 K),respectively.Connecting two thermally chargeable supercapacitor units in series,the generated output voltage of 500 mV further confirmed the stability of devices.When a single device was worn on the arm,a thermal voltage of 208.3 mV was obtained indicating the possibility of application in wearable electronics.

Silicon micropillar electrodes of lithiumion batteries used for characterizing electrolyte additives

The 100 crystal-oriented silicon micropillar array platforms were prepared by microfabrication processes for the purpose of electrolyte additive identification. The silicon micropillar array platform was used for the study of fluorinated vinyl carbonate(FEC), vinyl ethylene carbonate(VEC), ethylene sulfite(ES), and vinyl carbonate(VC) electrolyte additives in the LiPF_6 dissolved in a mixture of ethylene carbonate and diethyl carbonate electrolyte system using charge/discharge cycles, electrochemical impedance spectroscopy, cyclic voltammetry, scanning electron microscopy, and x-ray photoelectron spectroscopy. The results show that the silicon pillar morphology displays cross-shaped expansion after lithiation/delithiation, the inorganic lithium salt keeps the silicon pillar morphology intact, and the organic lithium salt content promotes a rougher silicon pillar surface. The presence of poly-(VC) components on the surface of FEC and VC electrodes allows the silicon pillar to accommodate greater volume expansion while remaining intact. This work provides a standard, fast, and effective test method for the performance analysis of electrolyte additives and provides guidance for the development of new electrolyte additives.

A Mathematic Model of Gas-diffusion Electrodes in Contact with Liquid Electrolytes

A mathematic model is developed which is applied to analyze the main factors that affect electrode performance and to account for the process of reaction and mass transfer in gas-diffusion electrodes in contact with liquid electrolytes. Electrochemical Thiele modulus φ^2 and electrochemical effectiveness factor η are introduced to elucidate the effects of diffusion on electrochemical reaction and utilization of the gas-diffusion electrode. Profile of the reactant along axial direction is discussed, dependence of electrode potential V on current density J, are predicated by means of the newly developed mathematical model.

Microzone-explosion synthesis of porous carbon electrodes for advanced aqueous solid-state supercapacitors with a high-voltage gel electrolyte

A new microzone-combustion synthesis is proposed for preparing S, N-doped hierarchically porous carbons(CAC-CN) with a novel mixed microstructure of sp~2 short-range order area and sp~3 defective area,achieving a coexistence of high conductivity and high capacitance as well as good access for electrolyte.By engineering ‘‘water in salts" into a polymer matrix, a high-voltage(2.5 V) aqueous gel electrolyte(HGWIS) is prepared and used to construct an aqueous solid-state SCs by in situ polymerization between the electrodes. The good match of CAC-CN electrode and HG-WIS electrolyte endows the assembled devices with superior high energy density and excellent capacitance retention, also a good temperature robustness, as well a high flexibility in 0-180° bending cycles. This study indicates that the collaborative design strategy of electrode materials and electrolyte would be great potential in exploring advanced aqueous solid-state SCs.

A comparative study on the reactivity of charged Ni-rich and Ni-poor positive electrodes with electrolyte at elevated temperatures using accelerating rate calorimetry

The reactivity between charged Li(Li_(0.115)Mn_(0.529)Ni_(0.339)Al_(0.017))O_(2)(Li-rich),single crystal Li(Ni_(0.8)Mn_(0.1)Co_(0.1))O_(2)(SC-NMC811),LiFePO_(4)(LFP) and LiMn_(0.8)Fe_(0.2)PO_(4)(LMFP) positive electrodes at different states of charge(SOCs) and traditional carbonate-based electrolyte at elevated temperatures is systematically studied using accelerating rate calorimetry(ARC).The results show that the SOC greatly affects the thermal stability of the Li-rich and SC-NMC811 when traditional carbonate-based electrolyte is used.Although an increase in the SOC increases the energy density of lithium-ion cells,it also increases the reactivity between charged Li-rich and SC-NMC811 samples with electrolyte at elevated temperatures.In comparison with SC-NMC811,the Li-rich samples are much more stable at elevated temperatures,and the latter have higher specific capacity.SC-NMC811 samples are less reactive than traditional polycrystalline NMC811.Both LFP and LMFP samples show excellent thermal stability at elevated temperatures.The substitution of Fe by Mn in the olivine series positive materials does not impact the reactivity with electrolyte.

Experimental investigation on the effect of surface characterization of electrodes on the gas bubble dynamics in electrolyte flow and performance of FLA batteries by using PIV

In the flooded lead_acid batteries(FLAB),gas bubbles are initially formed on the surface of the electrodes,which are produced by electrochemical reactions,and then released into the electrolyte.In the present investigation,the effect of surface characterization of electrodes of FLAB on the gas bubble dynamic parameters in the electrolyte flow at different charging/discharging rates(C-rates)are studied utilizing particle image velocimetry(PIV)method.The results show that the capacity of FLAB have a linear behavior due to changes in each of the two parameters of the surface characterization of electrodes and the Crate.At all State of charges(SOCs)of FLAB cells in different tests,increasing average roughness(Ra)and average wavelength of the roughness(λa)in the electrode surfaces,results in an increase in average bubble diameter and bubble rising velocity.Nevertheless,a sharp decrease in the void fraction of bubbles within the electrolyte was observed due to the increment inλa and Ra.Also,the effect of the rising movement of gas bubbles within the electrolyte on the average electrolyte velocity pattern in the gap between the electrodes by changing the surface characterization of electrodes are investigated in detail.