Real-time forward modeling and inversion of logging-while-drilling electromagnetic measurements in horizontal wells

Based on the pseudo-analytical equation of electromagnetic log for layered formation,an optimal boundary match method is proposed to adaptively truncate the encountered formation structures.An efficient integral method is put forward to significantly accelerate the convergence of Sommerfeld integral.By asymptotically approximating and subtracting the first reflection/transmission waves from the scattered field,the new Sommerfeld integral method has addressed difficulties encountered by the traditional digital filtering method,such as low computational precision and limited operating range,and realized the acceleration of the computation speed of logging-while-drilling electromagnetic measurements(LWD EM).By making use of the priori information from the offset/pilot wells and interactively adjusting the formation model,the optimum initial guesses of the inversion model is determined in order to predict the nearby formation boundaries.The gradient optimization algorithm is developed and an interactive inversion system for the LWD EM data from the horizontal wells is established.The inverted results of field data demonstrated that the real-time interactive inversion method is capable of providing the accurate boundaries of layers around the wellbore from the LWD EM,and it will benefit the wellbore trajectory optimization and reservoir interpretation.

Efficient finite-volume simulation of the LWD orthogonal azimuth electromagnetic response in a three-dimensional anisotropic formation using potentials on cylindrical meshes

In this study,the cylindrical finite-volume method(FVM)is advanced for the efficient and high-precision simulation of the logging while drilling(LWD)orthogonal azimuth electromagnetic tool(OAEMT)response in a three-dimensional(3 D)anisotropic formation.To overcome the ill-condition and convergence problems arising from the low induction number,Maxwell’s equations are reformulated into a mixed Helmholtz equation for the coupled potentials in a cylindrical coordinate system.The electrical fi eld continuation method is applied to approximate the perfectly electrical conducting(PEC)boundary condition,to improve the discretization accuracy of the Helmholtz equation on the surface of metal mandrels.On the base,the 3 D FVM on Lebedev’s staggered grids in the cylindrical coordinates is employed to discretize the mixed equations to ensure good conformity with typical well-logging tool geometries.The equivalent conductivity in a non-uniform element is determined by a standardization technique.The direct solver,PARDISO,is applied to efficiently solve the sparse linear equation systems for the multi-transmitter problem.To reduce the number of calls to PARDISO,the whole computational domain is divided into small windows that contain multiple measuring points.The electromagnetic(EM)solutions produced by all the transmitters per window are simultaneously solved because the discrete matrix,relevant to all the transmitters in the same window,is changed.Finally,the 3 D FVM is validated against the numerical mode matching method(NMM),and the characteristics of both the coaxial and coplanar responses of the EM field tool are investigated using the numerical results.

Probe method to measure the electromagnetic field in a plasma by Poynting vector conversion

In this paper,a high-precision electromagnetic measurement system suitable for a hightemperature and high-speed plasma is built to provide a platform for scientific research on the interaction mechanism of the electromagnetic fields and a plasma.This paper presents a method to measure the electromagnetic field inside a plasma by using a probe and Poynting vector conversion,which is a new and completely different method from the traditional method of measuring the electromagnetic field inside plasma.In addition,for this system and method,this work designs a microstrip antenna probe that can suppress multipath effects.This method is confirmed to be valid and usable after closed-loop verification by the CST software.

ELECTROMAGNETIC TOMOGRAPHY (EMT): THEORETICAL ANALYSIS OF THE FORWARD PROBLEM

Inductance-bared electromagnetic tomography (EMT) is a novel industrial process tomographic technique. Exact expressions of the magnetic field distribution in a two-dimensional object space were derived by analytically solving the forward problem for a particular two-component pow. The physical mechanisms within the sensor and the detectability limits of the EMT technique were quantitatively analyzed. Direct mathematical expressions for the field sensitivity and the sensitivity maps were established. To a certain extent, mathematical and theoretical bares are given for quantitative design of the sensor, detectability analysis of the EMT technique and image reconstruction of two-component processes based on the linear back-projection algorithm.

Measurement of Electron-Drift Velocity in Ar＋CH4 Mixtures Using Double-Grid Method

Based on analyzing the induced signals from the double-grids of an ionization chamber, the electron-drift time between the two grids is determined and the electron-drift velocity is derived. A waveform digitizer is employed to record pulses from the two grids of the ionization chamber. The electron-drift velocity is measured as a function of the reduced electric field E/p for eight different ratios of Ar＋CH4 mixtures. By analyzing the experimental data of this study, self-consistency of experimental data is achieved, and formulae for calculating electron-drift velocity in any ratio of Ar＋CH4 mixtures are obtained.

Progress in AMS Measurement of 182Hf at CIAE

Accelerator mass spectrometry （AMS） is one of the most promising methods to detect minute amounts of 182Hf. However, the sensitivity of 5×10^-11 for ^182Hf/180Hf obtained previously by the AMS method at China Institute of Atomic Energy （CIAE） cannot meet the requirement of some applications. We present some new improvements of measurement method for AMS measurement of 182Hf at the CIAE HI？13 tandem accelerator system. As a result, a sensitivity of 1.0×10^-11 for 182Hf/180Hf is achieved.

Time-Resolved Measurement of Radiatively Heated Iron 2p-3d Transmission Spectra

An experimental measurement of radiatively heated iron plasma transmission spectra was performed on Shenguang II laser facility. In the measurement, the self？emission spectrum, the backlighting spectrum, and the absorption spectrum were imaged with a flat filed grating and recorded on a gated micro channel plate detector to obtain the time-resolved transmission spectra in the range 10-20 ？ （approximately 0.6-1.3 keV）. Experimental results are compared with the calculation results of an unsolved transition array （UTA） code. The time-dependent relative shift in the positions of the 2p-3d transmission array is interpreted in terms of the plasma temperature variations.

An Adaptive Fast Multipole Higher Order Boundary Element Method for Power Frequency Electric Field of Substation

An adaptive fast multipole higher order boundary element method combining fast multipole （FM） with a higher order boundary element method is studied to solve the power frequency electric field （PFEF） of substations. In this new technique, the iterative equation solver GMRES is used in the FM, where matrix-vector multiplications are calculated using fast multipole expansions. The coefficients in the preconditioner for GMRES are stored and are used repeatedly in the direct evaluations of the near-field contributions. Then a 500kV outdoor substation is modeled and the PFEF of the substation is analyzed by the novel algorithm and other conventional methods. The results show that, in computational cost and the storages capability aspects, the algorithm proposed in this study has obvious advantages. It is suitable for the calculation of the large-scale PFEF in complex substations and the design of electromagnetic compatibility.

Characterizing THz Coherent Synchrotron Radiation at Femtosecond Linear Accelerator

The generation and observation of coherent THz synchrotron radiation from femtosecond electron bunches in the Shanghai Institute of Applied Physics femtosecond accelerator device is reported. We describe the experiment setup and present the first result of THz radiation properties such as power and spectrum.

Theoretical Design of a 104MHz Ladder Type IH-RFQ Accelerator

Beam dynamics and rf designs of a 104 MHz ladder type IH-RFQ （L-IH-RFQ） accelerator are finished at Peking University for the acceleration of 14C＋ from 40 keV to 500 keV. As a specific feature, the output beam energy spread is as low as 0.6% achieved with the internal discrete bunching method, which makes potential applications of RFQ feasible, such as accelerator mass spectrometry and ion implantation. Tolerances of the beam dynamics design are studied by means of changing the input beam parameters, and the results are quite satisfying. On the other hand, the L-IH-RFQ structure is employed, taking advantage of its mechanical stability and the absence of inter-electrode voltage asymmetry. Radio-frequency properties are studied and optimized for reducing power loss with Microwave Studio （MWS）. Tuning of the field flatness and frequency is investigated in principle.

High Power THz Undulator Radiation from Linear Accelerator

A 30-MeV femto-second electron linac is built at the Shanghai Institute of Applied Physics, which can produce high power, coherent THz undulator radiation. We report the experimental facility and measurement of the power, frequency spectrum. First experiments show the averaged power at THz to be about 20mW.

Proton Acceleration with Nano-Scale Micro-Structured Target by Circularly Polarized Laser Pulse

Two dimensional particle-in-cell simulations are taken to study the interaction of a circularly polarized laser pulse with a nano-scale micro-structured target. The protons which are doped in the rear side of the target experience the electrostatic fields caused by both the radiation pressure driven shock and the target normal sheath at the rear side of the target. A quasimonoenergetic proton bunch with central energy of about 11MeV and energy spread of ＆#8710; ε/ε about 0.18 is achieved by using a 3.45×1019 W/cm2, 66fs laser pulse. A comparison with the case of linearly polarized laser pulse and the same target condition is considered.

Proton Ratio of HL-2A Bucket Ion Source

For heating the tokamak plasma effectively, the ion source must be capable of producing ions with high proton ratio. The proton ratio, which is found to be more than 65.6% at the ion current of 19.6A with the extraction voltage of 39.6 k V, is measured with an image spectrograph by Doppler shift effect of Balmer-α-radiation spectrum emitted from fast hydrogen particles. The tendency of proton ratio with the ion density in experiment is almost the same as the mode devised by Zhang et al. Okumura et al. only gave the affection of the plasma volume and ion loss area on the proton ratio, but the relationship between the ion density in chamber and the proton ratio was not presented. We give the relationship.

Assessment of Primordial Radionuclides in Pakistani Red Bricks and Associated Radiation Doses

Specific activity of primordial radionuclides and associated radiation hazards due to 40K, 226Ra, and 232Th have been measured in backed red brick samples, collected from five highly populated areas of the North West Frontier Province of Pakistan. For the detection, analysis and data acquisition, a high purity germanium detector was used. Associated external doses were calculated using a Monte Carlo neutron photon transport code. A theoretical model to determine the gamma dose rate at 1 m height from the floor, made of bricks, was employed for the calculation of mass attenuation coefficient and self-absorption in the floor for the gamma energies of these radionuclides and their progeny. Monte Carlo simulation shows that in this study the floor, having more than an effective thickness of 15 cm, contributes very little to the external gamma dose rate. The values of the external dose rate and annual effective dose are found to be much lower than the world average as well as from other countries of the world.

Flowrate Measurement in Turbulent Liquid Metal Channel Flow Using Time-of-Flight Lorentz Force Velocimetry:Experimental Investigations and Numerical Modeling

Lorentz force velocimetry(LFV)is a suitable non-contact technique to measure flow velocity and flowrates in electrically conducting high-temperature melts.LFV is based on the principles of magnetohydrodynamics:when an electrically conducting fluid passes the field lines produced by a magnet system,eddy currents are induced within the fluid.The interactions of the eddy currents with the magnetic field generate Lorentz forces.Using LFV the counterforce acting on the magnet system is measured.Such a flowmeter consists of a permanent magnet system and an attached digital force sensor.The force recorded by the flowmeter is proportional to the flowrate Q and depends on both the electrical conductivity σ of the fluid and the spatial distribution of the applied magnet field B.However,in metallurgical applications,σ is often unknown or fluctuates in time as it strongly depends on both temperature and composition of the melt.In the present paper we investigate a technique called Time-of-Flight Lorentz force velocimetry ToF LFV.In this technique,the flowrate can be determined by just cross-correlating the two force signals recorded by two flowmeters which are arranged one behind the other separated by a certain distance D.Sensing the passage of the triggered vortices, this ToF LFV measures the transit time τ of these vortices.Then we recalculate the velocity V according to the relation V = D/τ.We experimentally and numerically study turbulent liquid metal flow in the test facility EFCO(electromagnetic flow control channel)using the eutectic alloy GainSn as a test fluid.Our experiments show that this electromagnetic ToF LFV is well suited to determine the flow velocity and flowrate.The experiments are accompanied by numerical simulations using the commercial program package FLUENT.