Toward high-efficiency perovskite solar cells with one-dimensional oriented nanostructured electron transport materials

The unique advantages of one-dimensional(1D)oriented nanostructures in light-trapping and chargetransport make them competitive candidates in photovoltaic(PV)devices.Since the emergence of perovskite solar cells(PSCs),1D nanostructured electron transport materials(ETMs)have drawn tremendous interest.However,the power conversion efficiencies(PCEs)of these devices have always significantly lagged behind their mesoscopic and planar counterparts.High-efficiency PSCs with 1D ETMs showing efficiency over 22%were just realized in the most recent studies.It yet lacks a comprehensive review covering the development of 1D ETMs and their application in PSCs.We hence timely summarize the advances in 1D ETMs-based solar cells,emphasizing on the fundamental and optimization issues of charge separation and collection ability,and their influence on PV performance.After sketching the classification and requirements for high-efficiency 1D nanostructured solar cells,we highlight the applicability of 1D TiO_(2)nanostructures in PSCs,including nanotubes,nanorods,nanocones,and nanopyramids,and carefully analyze how the electrostatic field affects cell performance.Other kinds of oriented nanostructures,e.g.,ZnO and SnO_(2)ETMs,are also described.Finally,we discuss the challenges and propose some potential strategies to further boost device performance.This review provides a broad range of valuable work in this fast-developing field,which we hope will stimulate research enthusiasm to push PSCs to an unprecedented level.

Alleviating Interfacial Recombination of Heterojunction Electron Transport Layer via Oxygen Vacancy Engineering for Efficient Perovskite Solar Cells Over 23%

Electron transport layer(ETL)is pivotal to charge carrier transport for PSCs to reach the Shockley-Queisser limit.This study provides a fundamental understanding of heterojunction electron transport layers(ETLs)at the atomic level for stable and efficient perovskite solar cells(PSCs).The bilayer structure of an ETL composed of SnO_(2) on TiO_(2) was examined,revealing a critical factor limiting its potential to obtain efficient performance.Alteration of oxygen vacancies in the TiO_(2) underlayer via an annealing process is found to induce manipulated band offsets at the interface between the TiO_(2) and SnO_(2) layers.In-depth electronic investigations of the bilayer structure elucidate the importance of the electronic properties at the interface between the TiO_(2) and SnO_(2) layers.The apparent correlation in hysteresis phenomena,including current density-voltage(J-V)curves,appears as a function of the type of band alignment.Density functional theory calculations reveal the intimate relationship between oxygen vacancies,deep trap states,and charge transport efficiency at the interface between the TiO_(2) and SnO_(2) layers.The formation of cascade band alignment via control over the TiO_(2) underlayer enhances device performance and suppresses hysteresis.Optimal performance exhibits a power conversion efficiency(PCE)of 23.45%with an open-circuit voltage(V_(oc))of 1.184 V,showing better device stability under maximum power point tracking compared with a staggered bilayer under one-sun continuous illumination.

Blue light is more essential than red light for maintaining the activities of photosystem Ⅱ and Ⅰ and photosynthetic electron transport capacity in cucumber leaves

Blue and red lights differently regulate leaf photosynthesis. Previous studies indicated that plants under blue light generally exhibit better photosynthetic characteristics than those under red light. However, the regulation mechanism of related photosynthesis characteristics remains largely unclear. Here, four light qualities treatments （300 μmol m-2 s-1） including white fluorescent light （FL）, blue monochromatic light （B, 440 nm）, red monochromatic light （R, 660 nm）, and a combination of red and blue light （RB, R：B=8：1） were carried out to investigate their effects on the activity of photosystem II （PSII） and photosystem I （PSI）, and photosynthetic electron transport capacity in the leaves of cucumber （Cucumis sativus L.） seedlings. The results showed that compared to the FL treatment, the R treatment significantly limited electron transport rate in PSII （ETR11） and in PSI （ETR1） by 79.4 and 66.3%, respectively, increased non-light induced non-photochemical quenching in PSII （q^No） and limitation of donor side in PSI （φND） and reduced most JIP-test parameters, suggesting that the R treatment induced suboptimal activity of photosystems and inhibited electron transport from PSII donor side up to PSI. However, these suppressions were effectively alleviated by blue light addition （RB）. Compared with the R treatment, the RB treatment significantly increased ETR, and ETR1 by 176.9 and 127.0%, respectively, promoted photosystems activity and enhanced linear electron transport by elevating electron transport from QA to PSI. The B treatment plants exhibited normal photosystems activity and photosynthetic electron transport capacity similar to that of the FL treatment. It was concluded that blue light is more essential than red light for normal photosynthesis by mediating photosystems activity and photosynthetic electron transport capacity.

Forward and reverse electron transport properties across a CdS/Si multi-interface nanoheterojunction

The electron transport behavior across the interface plays an important role in determining the performance of op- toelectronic devices based on heterojunctions. Here through growing CdS thin film on silicon nanoporous pillar array, an untraditional, nonplanar, and multi-interface CdS/Si nanoheterojunction is prepared. The current density versus voltage curve is measured and an obvious rectification effect is observed. Based on the fitting results and model analyses on the forward and reverse conduction characteristics, the electron transport mechanism under low forward bias, high forward bias, and reverse bias are attributed to the Ohmic regime, space-charge-limited current regime, and modified Poole-Frenkel regime respectively. The forward and reverse electrical behaviors are found to be highly related to the distribution of inter- facial trap states and the existence of localized electric field respectively. These results might be helpful for optimizing the preparing procedures to realize high-performance silicon-based CdS optoelectronic devices.

Investigation of the performance of CF3I/c-C4F8/N2 and CF3I/c-C4F8/CO2 gas mixtures from electron transport parameters

CF3I gas mixtures have attracted considerable attention as potential environmentally-friendly alternatives to SF6 gas,owing to their excellent insulating performance.This paper attempts to study the CF3I ternary gas mixtures with c-C4F8 and buffer gases N2 and CO2 by considering dielectric strength from electron transport parameters based on the Boltzmann method and synergistic effect analysis,compared with SF6 gas mixtures.The results confirm that the critical electric field strength of CF3I/c-C4F8/70%CO2 is greater than that of 30%SF6/70%CO2 when the CF3I content is greater than 17%.Moreover,a higher content of c-C4F8 decreases the sensitivity of gas mixtures to an electric field,and this phenomenon is more obvious in CF3I/c-C4F8/CO2 gas mixtures.The synergistic effects for CF3I/c-C4F8/70%N2 were most obvious when the c-C4F8 content was approximately 20%,and for CF3I/c-C4F8/70%CO2 when the c-C4F8 content was approximately 10%.On the basis of this research,CF3I/c-C4F8/70%N2 shows better insulation performance when the c-C4F8 content is in the15%–20%range.For CF3I/c-C4F8/70%CO2,when the c-C4F8 content is in the 10%–15%range,the gas mixtures have excellent performance.Hence,these gas systems might be used as alternative gas mixtures to SF6 in high-voltage equipment.

Manipulation and optimization of electron transport by nanopore array targets

The transport of sub-picosecond laser-driven fast electrons in nanopore array targets is studied.Attributed to the generation of micro-structured magnetic fields,most fast electron beams are proven to be effectively guided and restricted during the propagation.Different transport patterns of fast electrons in the targets are observed in experiments and reproduced by particle-in-cell simulations,representing two components:initially collimated low-energy electrons in the center and high-energy scattering electrons turning into surrounding annular beams.The critical energy for confined electrons is deduced theoretically.The electron guidance and confinement by the nano-structured targets offer a technological approach to manipulate and optimize the fast electron transport by properly modulating pulse parameters and target design,showing great potential in many applications including ion acceleration,microfocus x-ray sources and inertial confinement fusion.

Preparation and property of a novel soluble electron transport POSS-based hybrid material

A novel POSS-based organic/inorganic hybrid covalently attached at molecular level, 2-（4-（allyloxy）phenyl）-5-（4-（octyloxy）phenyl）-1,3,4-oxadiazole-POSS （6） （abbreviated as oxadiazole-POSS） was synthesized by Pt（dcp） catalyst. The hybrid was soluble in common organic solvents such as CHCl3, toluene, C2H4Cl2, and THF. Its structures and properties were characterized and evaluated with FTIR, 1^H NMR, 13^C NMR,29^Si NMR, EA, TGA, DSC, GPC, and CV, respectively. The results show that the novel hybrid possesses high thermal stability and good electron injection ability.

Contact effect in the dynamic electron transport of a two-probe mesoscopic conductor

Based on the self-consistent electron dynamic transport theory for multi-probe mesoscopic systems, we calculate the distribution of internal potential, charge density, and ac conductance of a two-probe mesoscopic conductor with wide trapezoid reservoirs, and study the contact effect. The results show that including the contact effect can make a significant difference to the frequency-dependent electron transport properties. In the nonzero frequency case, the internal potential and the charge density are complex with extremely small imaginary parts. Importantly, the imaginary part of the charge density gives rise to a real ac conductance （admittance）, which corresponds to the charge-relaxation resistance.

Numerical investigation of non-local electron transport in laser-produced plasmas

Non-local electron transport in laser-produced plasmas under inertial confinement fusion （ICF） conditions is studied based on Fokker-Planck （FP） and hydrodynamic simulations. A comparison between the classical Spitzer-Harm （SH） transport model and non-local transport models has been made. The result shows that among those non-local models the Epperlein and Short （ES） model of heat flux is in reasonable agreement with the FP simulation in overdense region. However, the non-local models are invalid in the hot underdense plasmas. Hydrodynamic simulation is performed with the flux limiting model and the non-local model, separately. The simulation results show that in the underdense region of the laser-produced plasmas the temperature given by the flux limiting model is significantly higher than that given with the non-local model.

Effect of Kinetic Alfvén Waves on Electron Transport in an Ion-Scale Flux Rope

At the Earth＇s magnetopause, the electron transport due to kinetic Alfvén waves（KAWs） is investigated in an ion-scale flux rope by the Magnetospheric Multiscale mission. Clear electron dropout around 90° pitch angle is observed throughout the flux rope, where intense KAWs are identified. The KAWs can effectively trap electrons by the wave parallel electric field and the magnetic mirror force, allowing electrons to undergo Landau resonance and be transported into more field-aligned directions. The pitch angle range for the trapped electrons is estimated from the wave analysis, which is in good agreement with direct pitch angle measurements of the electron distributions. The newly formed beam-like electron distribution is unstable and excites whistler waves,as revealed in the observations. We suggest that KAWs could be responsible for the plasma depletion inside a flux rope by this transport process, and thus be responsible for the formation of a typical flux rope.

Electron transport in Dirac and Weyl semimetals

Recently, the Dirac and Weyl semimetals have attracted extensive attention in condensed matter physics due to both the fundamental interest and the potential application of a new generation of electronic devices. Here we review the exotic electrical transport phenomena in Dirac andWeyl semimetals. Section 1 is a brief introduction to the topological semimetals（TSMs）. In Section 2 and Section 3, the intriguing transport phenomena in Dirac semimetals（DSMs） andWeyl semimetals（WSMs） are reviewed, respectively. The most widely studied Cd_3A_（s2） and the TaAs family are selected as representatives to show the typical properties of DSMs and WSMs, respectively. Beyond these systems, the advances in other TSM materials,such as ZrTe_5 and the MoTe_2 family, are also introduced. In Section 4, we provide perspectives on the study of TSMs especially on the magnetotransport investigations.

Improved performance of organic light-emitting diodes with dual electron transporting layers

In this study the performance of organic light-emitting diodes （OLEDs） are enhanced significantly, which is based on dual electron transporting layers （13phen/CuPc）. By adjusting the thicknesses of Bphen and CuPc, the maximal luminescence, the maximal current efficiency, and the maximal power efficiency of the device reach 17570 cd/m^2 at 11 V, and 5.39 cd/A and 3.39 lm/W at 3.37 mA/cm^2 respectively, which are enhanced approximately by 33.4%, 39.3%, and 68.9%, respectively, compared with those of the device using Bphen only for an electron transporting layer. These results may provide some valuable references for improving the electron injection and the transportation of OLED.

Scalable spray coated high performance sulfurized electron transporter for efficient and stable perovskite solar modules

The stability issue has been acknowledged as the bottleneck in the practical application of perovskite photovoltaics,while the stabilized interface between the perovskites and charge transport layers dominates their stability performance under different stresses.Here,we developed a high-performance sulfurized zinc-titanium mixed oxide(ZTO-S)electron transport layer(ETL)to fabricate large-area efficient and long-term 85℃/85%RH stable perovskite solar modules.The scalably prepared ZTO-S using the facile spray coating method demonstrates excellent electron mobility close to that of Zn O,in addition to promoting the uniform crystallization of perovskite film across the entire module via the interaction between surface S and Pb^(2+).Furthermore,this novel coordination stabilized the interface and reduced the interfacial non-radiative recombination defects within the devices,yielding an efficient and stable performance for the modules.High efficiency of 21.73%and 17.50%was achieved for blade-coated 36 cm^(2)and 100 cm^(2)perovskite solar modules,respectively.In addition,the encapsulated module(36 cm^(2))shows an attractive humidity and heat stability(85℃/85%RH)performance with a maintained 93.5%of the initial PCE over 1000 h.

Non-conjugated polymers as thickness-insensitive electron transport materials in high-performance inverted organic solar cells

Two non-conjugated polymers PEIE-DBO and PEIE-DCO, prepared by quaternization of polyethyleneimine ethoxylate by 1,8-dibromooctane and 1,8-dichlorooctane respectively, are developed as electron transport layer(ETL) in high-performance inverted organic solar cells(OSCs), and the effects of halide ions on polymeric photoelectric performance are fully investigated. PEIE-DBO possesses higher electron mobility(3.68×10-4 cm2 V-1s-1), higher conductivity and more efficient exciton dissociation and electron extraction, attributed to its lower work function(3.94 eV) than that of PEIE-DCO, which results in better photovoltaic performance in OSCs. The inverted OSCs with PTB7-Th: PC71BM as photoactive layer and PEIE-DBO as ETL exhibit higher PCE of 10.52%, 9.45% and 9.09% at the thickness of 9, 35 and 50 nm,respectively. To our knowledge, PEIE-DBO possesses the best thickness-insensitive performance in polymeric ETLs of inverted fullerene-based OSCs. Furthermore, PEIE-DBO was used to fabricate the inverted non-fullerene OSCs(PM6:Y6) and obtained a high PCE of 15.74%, which indicates that PEIE-DBO is effective both in fullerene-based OSCs and fullerene-free OSCs.

Highly efficient flexible perovskite solar cells with vacuum-assisted low-temperature annealed SnO2 electron transport layer

The demand for lightweight, flexible, and high-performance portable power sources urgently requires high-efficiency and stable flexible solar cells. In the case of perovskite solar cells(PSCs), most of the common electron transport layer(ETL) needs to be annealed for improving the optoelectronic properties,while conventional flexible substrates could barely stand the high temperature. Herein, a vacuumassisted annealing SnO_(2) ETL at low temperature(100℃) is utilized in flexible PSCs and achieved high efficiency of 20.14%. Meanwhile, the open-circuit voltage(V_(oc)) increases from 1.07 V to 1.14 V. The flexible PSCs also show robust bending stability with 86.8% of the initial efficiency is retained after 1000 bending cycles at a bending radius of 5 mm. X-ray photoelectron spectroscopy(XPS), atomic force microscopy(AFM), and contact angle measurements show that the density of oxygen vacancies, the surface roughness of the SnO_(2) layer, and film hydrophobicity are significantly increased, respectively. These improvements could be due to the oxygen-deficient environment in a vacuum chamber, and the rapid evaporation of solvents. The proposed vacuum-assisted low-temperature annealing method not only improves the efficiency of flexible PSCs but is also compatible and promising in the large-scale commercialization of flexible PSCs.

Composite electron transport layer for efficient N-I-P type monolithic perovskite/silicon tandem solar cells with high open-circuit voltage

Perovskite/silicon tandem solar cells(PSTSCs) have exhibited huge technological potential for breaking the Shockley-Queisser limit of single-junction solar cells. The efficiency of P-I-N type PSTSCs has surpassed the single-junction limit, while the performance of N-I-P type PSTSCs is far below the theoretical value. Here, we developed a composite electron transport layer for N-I-P type monolithic PSTSCs with enhanced open-circuit voltage(VOC) and power conversion efficiency(PCE). Lithium chloride(Li Cl) was added into the tin oxide(SnO_(2)) precursor solution, which simultaneously passivated the defects and increased the electron injection driving force at the electron transfer layer(ETL)/perovskite interface.Eventually, we achieved monolithic PSTSCs with an efficiency of 25.42% and V_(OC) of 1.92 V, which is the highest PCE and VOCin N-I-P type perovskite/Si tandem devices. This work on interface engineering for improving the PCE of monolithic PSTSCs may bring a new hot point about perovskite-based tandem devices.

Metal Induced Inhibition of Photosynthesis,Photosynthetic Electron Transport Chain and ATP Content of Anabaena doliolum and Chlorella vulgaris:Interaction with Exogenous ATP

This study demonstrates a concentration dependent inhibition of carbon fixation, O2 evolution, photosynthetic electron transport chain and ATP content of A. doliolum and C. vulgaris by Cu, Ni and Fe. Although the mode of inhibition of photosynthetic electron transport chain of both the algae was similar, PS II depicted greater sensitivity to the test metals used. The toxicity in both organisms was Cu > Ni > Fe. A. doliolum was, however, more sensitive to Cu and Ni, and C. vulgaris to Fe. Toxicity was generally dependent on metal uptake, which in turn was dependent on their concentrations in the external medium. A partial restoration of nutrient uptake, carbon fixation, and enzyme activities following supplementation of exogenous ATP suggests that ATP regulates toxicity through chelation.

Inverted organic solar cells with solvothermal synthesized vanadium-doped TiO2 thin films as efficient electron transport layer

We investigated the effects of using different thicknesses of pure and vanadium-doped thin films of TiO2 as the electron transport layer in the inverted configuration of organic photovoltaic cells based on poly（3-hexylthiophene） P3HT：[6-6] phenyl-（6） butyric acid methyl ester（PCBM）. 1% vanadium-doped TiO2nanoparticles were synthesized via the solvothermal method. Crystalline structure, morphology, and optical properties of pure and vanadium-doped TiO2 thin films were studied by different techniques such as x-ray diffraction, scanning electron microscopy, transmittance electron microscopy, and UV–visible transmission spectrum. The doctor blade method which is compatible with roll-2-roll printing was used for deposition of pure and vanadium-doped TiO2 thin films with thicknesses of 30 nm and 60 nm. The final results revealed that the best thickness of TiO2 thin films for our fabricated cells was 30 nm. The cell with vanadium-doped TiO2 thin film showed slightly higher power conversion efficiency and great Jsc of 10.7 mA/cm^2 compared with its pure counterpart. In the cells using 60 nm pure and vanadium-doped TiO2 layers, the cell using the doped layer showed much higher efficiency. It is remarkable that the external quantum efficiency of vanadium-doped TiO2 thin film was better in all wavelengths.

n-type ZnS used as electron transport material in organic light-emitting diodes

This paper reports on the n-type ZnS used as electron transport layer for the organic light-emitting diodes （OLEDs）. The naphthyl-substituted benzidine derivative （NPB） and tris （8-hydroxyquinoline） aluminium （Alq3） are used as the hole transport layer and the emitting layer respectively. The insertion of the n-type ZnS layer enhances the electron injection in the OLEDs. The study was carried out on OLEDs of structures： indium-tin-oxide （ITO）/NPB/Alq3/ZnS/LiF/AL, ITO/NPB/Alq3/LiF/AL and ITO/NPB/Alq3/AL. The luminance and efficiency of the device containing this electron transport layer are increased significantly over those obtained from conventional devices due to better carrier balance.

The photorefractive sensitivity and the effective electron transport length in two-centre holographic recording

In this paper the photorefractive sensitivity defined for single-centre holographic recording is modified to adapt two-centre holographic recording. Based on the time analytic solution of Kukhtarev equations for doubly doped crystals, the analytical expression of photorefractive sensitivity is given. For comparison with single-centre holographic recording and summing the electron competition effects between the deeper and shallower traps, an effective electron transport length is proposed, which varies with the intensity ratios of recording light to sensitive light. According to analyses in this paper, the lower photorefractive sensitivity in two-centre holographic recording is mainly due to the lower concentration of unionized dopants in the shallower centre and the lower effective electron transport length.