The rising number of electronic control units （ECUs） in vehicles and the decreasing time to market have led to the need for advanced methods of calibration. A multi-ECU calibration system was developed based on the ...The rising number of electronic control units （ECUs） in vehicles and the decreasing time to market have led to the need for advanced methods of calibration. A multi-ECU calibration system was developed based on the explicit calibration protocol （XCP） and J1939 communication protocol to satisfy the need of calibrating multiple ECUs simultaneously. The messages in the controller area network （CAN） are defined in the J1939 protocol. Each CAN node can get its own calibration messages and information from other ECUs, and block other messages by qualifying the CAN messages with priority, source or destination address. The data field of the calibration message is designed with the XCP, with CAN acting as the transport layer. The calibration sessions are setup with the event-triggered XCP driver in the master node and the responding XCP driver in the slave nodes. Mirroring calibration variables from ROM to RAM enables the user to calibrate ECUs online. The application example shows that the multi-ECU calibration system can calibrate multiple ECUs simultaneously, and the main program can also accomplish its calculation and send commands to the actuators in time. By the multi-ECU calibration system, the calibration effort and time can be reduced and the variables in ECU can get a better match with the variables of other ECUs.展开更多
A hardware-in-the-loop simulating platform is developed to avoid designing defects caused by the complicated logical structure and multiple-functional buildup of the dectronic control unit（ECU）in modem diesel engine...A hardware-in-the-loop simulating platform is developed to avoid designing defects caused by the complicated logical structure and multiple-functional buildup of the dectronic control unit（ECU）in modem diesel engines, and to diminish potential damages on components or human exposure to dangers in R＆D en- deavor. This plat-form consists of a computer installed with software Matlab/Simulink/RTW and dSPACE/ ControlDesk; a diesel engine ECU, and a dSPACE autobox which runs a real-time diesel engine model. A typical model of diesel engine with turbocharger and intercooler is presented. Based on this model our research is carried out with a real ECU to test its software control strategies. Results show that by using the diesel engine model downloaded inside, the hardware-in-the-loop platform can simulate diesel engine＇s working conditions and generate all kinds of sensor signals which ECU needs on a real-time basis. So the ECU control strategies can be validated and relevant parameters roughly calibrated.展开更多
The high working junction temperature of power component is the most common reason of its failure. So the thermal design is of vital importance in electronic control unit （ECU） design. By means of circuit simulation...The high working junction temperature of power component is the most common reason of its failure. So the thermal design is of vital importance in electronic control unit （ECU） design. By means of circuit simulation, the thermal design of ECU for electronic unit pump （EUP） fuel system is applied. The power dissipation model of each power component in the ECU is created and simulated. According to the analyses of simulation results, the factors which affect the power dissipation of components are analyzed. Then the ways for reducing the power dissipation of power components are carried out. The power dissipation of power components at different engine state is calculated and analyzed. The maximal power dissipation of each power component in all possible engine state is also carried out based on these simulations. A cooling system is designed based on these studies. The tests show that the maximum total power dissipation of ECU drops from 43.2 W to 33.84 W after these simulations and optimizations. These applications of simulations in thermal design of ECU can greatly increase the quality of the design, save the design cost and shorten design time展开更多
针对传统电控空气悬架电子控制单元(Electronic Control Unit,ECU)下线检测过程中存在的人工检测精准度差、效率低等问题,开发了一款自动电控空气悬架ECU下线检测系统。分析了电控空气悬架ECU下线检测系统各项技术需求,设计了上位机+系...针对传统电控空气悬架电子控制单元(Electronic Control Unit,ECU)下线检测过程中存在的人工检测精准度差、效率低等问题,开发了一款自动电控空气悬架ECU下线检测系统。分析了电控空气悬架ECU下线检测系统各项技术需求,设计了上位机+系统检测平台的系统架构;选择数据采集卡、CAN卡等部件搭建了下线检测系统检测平台;采用C#编程语言开发了上位机软件,软件采用UI界面层、业务逻辑层和数据层的三层架构,通过CAN总线通讯方式实现上位机、检测平台及待测ECU的双向通讯。测试结果表明,该下线检测系统可实现电控空气悬架ECU自动下线质量检测,并完成了测试数据的智能管理,满足电控空气悬架ECU的检测功能需求。展开更多
This paper is concerned with the development of electronic controller for turbine POwer units. In order to increase the reliability of the POwer unit, three control loops working in the hi-backup mode have been employ...This paper is concerned with the development of electronic controller for turbine POwer units. In order to increase the reliability of the POwer unit, three control loops working in the hi-backup mode have been employed. This control strategy is able to satisfy the demands of the application of the power unit to the aviation fields.展开更多
The performance of the electronic unit pump (EUP) diesel engine is studied, it will be used in the integrated powertrain and its multi parameters are controllable. Both the theoretical analysis and experiment research...The performance of the electronic unit pump (EUP) diesel engine is studied, it will be used in the integrated powertrain and its multi parameters are controllable. Both the theoretical analysis and experiment research are taken. A control unit for the fuel quantity and timing in crankshaft domain is designed on this basis and the engine experiment test has been done. For the constant speed camshaft driving EUP system, the fuel quantity will increase as the supply angle goes up and injection timing has no effect. The control precision can reach 1°CA. The full injection timing MAP and engine peak performance curves are made successfully.展开更多
By means of circuit simulation, hardware of electronic control unit （ECU） of high pressure common-rail electronic control fuel system for diesel engine is designed. According to the system requirements for hardware ...By means of circuit simulation, hardware of electronic control unit （ECU） of high pressure common-rail electronic control fuel system for diesel engine is designed. According to the system requirements for hardware of ECU, signal-processing circuit of variable reluctance （VR） sensor, filter circuit for input signal, high voltage power circuit and driver and protection circuit of solenoid are simulated as emphases. Difficulties of wide scope of VR sensor output signal, efficiency of high voltage power and reliable and swift driver of solenoid are solved. The results of simulation show that the hardware meets the requirement of the fuel system. At the same time, circuit simulation can greatly increase quality of the design, alleviate design labor and shorten design time.展开更多
为了方便更新汽车电子控制单元(electronic control unit,ECU)的应用代码,针对汽车控制系统自身的特点,设计出汽车ECU在线升级系统。该升级系统利用车身控制器局域网络(controller area network,CAN),遵循诊断协议ISO15765,将ISO15765...为了方便更新汽车电子控制单元(electronic control unit,ECU)的应用代码,针对汽车控制系统自身的特点,设计出汽车ECU在线升级系统。该升级系统利用车身控制器局域网络(controller area network,CAN),遵循诊断协议ISO15765,将ISO15765诊断协议传输层和应用层规范应用于在线升级系统的上位机与ECU之间通信,实现对车身控制系统中各个ECU节点的在线更新应用代码功能。给出了该升级系统在STM8和XC167CI单片机的试验结果。试验证明,该升级系统不仅能够满足实际的代码更新要求,而且具有较强的通用性和可扩展性。展开更多
文摘The rising number of electronic control units （ECUs） in vehicles and the decreasing time to market have led to the need for advanced methods of calibration. A multi-ECU calibration system was developed based on the explicit calibration protocol （XCP） and J1939 communication protocol to satisfy the need of calibrating multiple ECUs simultaneously. The messages in the controller area network （CAN） are defined in the J1939 protocol. Each CAN node can get its own calibration messages and information from other ECUs, and block other messages by qualifying the CAN messages with priority, source or destination address. The data field of the calibration message is designed with the XCP, with CAN acting as the transport layer. The calibration sessions are setup with the event-triggered XCP driver in the master node and the responding XCP driver in the slave nodes. Mirroring calibration variables from ROM to RAM enables the user to calibrate ECUs online. The application example shows that the multi-ECU calibration system can calibrate multiple ECUs simultaneously, and the main program can also accomplish its calculation and send commands to the actuators in time. By the multi-ECU calibration system, the calibration effort and time can be reduced and the variables in ECU can get a better match with the variables of other ECUs.
基金Sponsored by the Ministerial Level Advanced Research(10660060220)
文摘A hardware-in-the-loop simulating platform is developed to avoid designing defects caused by the complicated logical structure and multiple-functional buildup of the dectronic control unit（ECU）in modem diesel engines, and to diminish potential damages on components or human exposure to dangers in R＆D en- deavor. This plat-form consists of a computer installed with software Matlab/Simulink/RTW and dSPACE/ ControlDesk; a diesel engine ECU, and a dSPACE autobox which runs a real-time diesel engine model. A typical model of diesel engine with turbocharger and intercooler is presented. Based on this model our research is carried out with a real ECU to test its software control strategies. Results show that by using the diesel engine model downloaded inside, the hardware-in-the-loop platform can simulate diesel engine＇s working conditions and generate all kinds of sensor signals which ECU needs on a real-time basis. So the ECU control strategies can be validated and relevant parameters roughly calibrated.
文摘The high working junction temperature of power component is the most common reason of its failure. So the thermal design is of vital importance in electronic control unit （ECU） design. By means of circuit simulation, the thermal design of ECU for electronic unit pump （EUP） fuel system is applied. The power dissipation model of each power component in the ECU is created and simulated. According to the analyses of simulation results, the factors which affect the power dissipation of components are analyzed. Then the ways for reducing the power dissipation of power components are carried out. The power dissipation of power components at different engine state is calculated and analyzed. The maximal power dissipation of each power component in all possible engine state is also carried out based on these simulations. A cooling system is designed based on these studies. The tests show that the maximum total power dissipation of ECU drops from 43.2 W to 33.84 W after these simulations and optimizations. These applications of simulations in thermal design of ECU can greatly increase the quality of the design, save the design cost and shorten design time
文摘针对传统电控空气悬架电子控制单元(Electronic Control Unit,ECU)下线检测过程中存在的人工检测精准度差、效率低等问题,开发了一款自动电控空气悬架ECU下线检测系统。分析了电控空气悬架ECU下线检测系统各项技术需求,设计了上位机+系统检测平台的系统架构;选择数据采集卡、CAN卡等部件搭建了下线检测系统检测平台;采用C#编程语言开发了上位机软件,软件采用UI界面层、业务逻辑层和数据层的三层架构,通过CAN总线通讯方式实现上位机、检测平台及待测ECU的双向通讯。测试结果表明,该下线检测系统可实现电控空气悬架ECU自动下线质量检测,并完成了测试数据的智能管理,满足电控空气悬架ECU的检测功能需求。
文摘This paper is concerned with the development of electronic controller for turbine POwer units. In order to increase the reliability of the POwer unit, three control loops working in the hi-backup mode have been employed. This control strategy is able to satisfy the demands of the application of the power unit to the aviation fields.
文摘The performance of the electronic unit pump (EUP) diesel engine is studied, it will be used in the integrated powertrain and its multi parameters are controllable. Both the theoretical analysis and experiment research are taken. A control unit for the fuel quantity and timing in crankshaft domain is designed on this basis and the engine experiment test has been done. For the constant speed camshaft driving EUP system, the fuel quantity will increase as the supply angle goes up and injection timing has no effect. The control precision can reach 1°CA. The full injection timing MAP and engine peak performance curves are made successfully.
文摘By means of circuit simulation, hardware of electronic control unit （ECU） of high pressure common-rail electronic control fuel system for diesel engine is designed. According to the system requirements for hardware of ECU, signal-processing circuit of variable reluctance （VR） sensor, filter circuit for input signal, high voltage power circuit and driver and protection circuit of solenoid are simulated as emphases. Difficulties of wide scope of VR sensor output signal, efficiency of high voltage power and reliable and swift driver of solenoid are solved. The results of simulation show that the hardware meets the requirement of the fuel system. At the same time, circuit simulation can greatly increase quality of the design, alleviate design labor and shorten design time.
文摘为了方便更新汽车电子控制单元(electronic control unit,ECU)的应用代码,针对汽车控制系统自身的特点,设计出汽车ECU在线升级系统。该升级系统利用车身控制器局域网络(controller area network,CAN),遵循诊断协议ISO15765,将ISO15765诊断协议传输层和应用层规范应用于在线升级系统的上位机与ECU之间通信,实现对车身控制系统中各个ECU节点的在线更新应用代码功能。给出了该升级系统在STM8和XC167CI单片机的试验结果。试验证明,该升级系统不仅能够满足实际的代码更新要求,而且具有较强的通用性和可扩展性。
