In the hot summer&cold winter zone in China,intermittent heating space for rooms is widely used.However,in comparison with continuous space heating,the energy-saving performance of intermittent space heating has n...In the hot summer&cold winter zone in China,intermittent heating space for rooms is widely used.However,in comparison with continuous space heating,the energy-saving performance of intermittent space heating has not been sufficiently investigated.This paper studied the factors influencing the energy performance of intermittent heating for the representativeoffice inhot summer&coldwinter zone.Basedon theheatbalancemethod,adynamic thermalmodel of the intermittent heating roomwas built and tested by experiments.And then,it analyzed the total space heating load,the amount of energy saving and energy saving ratio of the intermittent heating under different preheating hours,occupation hours,required roomtemperatures,air change rates,overall heat transfer coefficients(U-value)of windows and wall materials.If the adjacent rooms were not heated,for a typical room occupied about 10 h a day,the energy-saving ratio of intermittent heating was about 30%compared with continuous heating.But the preheating power was higher than two times of continuous heating.The results also indicated that the occupation hours had a significant effect on energy saving amount and ratio,it should be noted that the energy saving ratio by intermittent heating was much lower than the unoccupied period ratio.Relative to other factors,the heating temperatures,room air change rates and U-value of windows,and room envelope materials had little effect on energy efficiency.If the adjacent rooms were heated in the same manner as the roomin question,the energy-saving ratio of the total load of intermittent heating was heavily reduced to 8.46%.展开更多
Denim is widely accepted among exported textile products due to its aesthetics, appearance, and fashion. Practitioners employed several physical or chemical treatments to improve denim qualities in denim finishing ope...Denim is widely accepted among exported textile products due to its aesthetics, appearance, and fashion. Practitioners employed several physical or chemical treatments to improve denim qualities in denim finishing operations. So, several treatment processes, including enzymatic, bleaching, singeing, heat set, and ozone finish, are used, which made this processing more energy consumption and time-consuming. Therefore, it is significant to investigate how changing the chemicals and raw ingredients could improve the finishing process, which is environmentally and economically beneficial for sustainable production practices in the denim finishing process. This study’s research design comprises an experimental investigation in a denim plant in Bangladesh. Two different fabrics were chosen to analyze, determining the potential savings of finishing on the denim fabrics’ performance characteristics. By deducting singeing and heat-set processes, the researchers ran an experimental process by maintaining the same length of fabric. Then, the impacts of finishing process optimization on the mechanical, thermal, and comfort parameters of drape, stiffness, and tear strength were examined. The study’s findings demonstrated that this experiment increased productivity and reduced the finishing unit’s energy consumption without compromising the denim fabrics’ quality. This study significantly impacts environmental sustainability by preserving limited energy resources and manufacturing denim finishing processes.展开更多
Purpose–To address the problem that the current train operation mode that train selects one of several offline pre-generated control schemes before the departure and operates following the scheme after the departure,...Purpose–To address the problem that the current train operation mode that train selects one of several offline pre-generated control schemes before the departure and operates following the scheme after the departure,energy-saving performance of the whole metro system cannot be guaranteed.Design/methodology/approach–A cooperative train control framework is formulated to regulate a novel train operation mode.The classic train four-phase control strategy is improved for generating specific energy-efficient control schemes for each train.An improved brute force(BF)algorithm with a two-layer searching idea is designed to solve the optimisation model of energy-efficient train control schemes.Findings–Case studies on the actual metro line in Guangzhou,China verify the effectiveness of the proposed train control methods compared with four-phase control strategy under different kinds of train operation scenarios and calculation parameters.The verification on the computation efficiency as well as accuracy of the proposed algorithm indicates that it meets the requirement of online optimisation.Originality/value–Most existing studies optimised energy-efficient train timetable or train control strategies through an offline process,which has a defect in coping with the disturbance or delays effectively and promptly during real-time train operation.This paper studies an online optimisation of cooperative train control based on the rolling optimisation idea,where energy-efficient train operation can be realised once train running time is determined,thus mitigating the impact of unpredictable operation situations on the energy-saving performance of trains.展开更多
As the main link of ground engineering,crude oil gathering and transportation systems require huge energy consumption and complex structures.It is necessary to establish an energy efficiency evaluation system for crud...As the main link of ground engineering,crude oil gathering and transportation systems require huge energy consumption and complex structures.It is necessary to establish an energy efficiency evaluation system for crude oil gathering and transportation systems and identify the energy efficiency gaps.In this paper,the energy efficiency evaluation system of the crude oil gathering and transportation system in an oilfield in western China is established.Combined with the big data analysis method,the GA-BP neural network is used to establish the energy efficiency index prediction model for crude oil gathering and transportation systems.The comprehensive energy consumption,gas consumption,power consumption,energy utilization rate,heat utilization rate,and power utilization rate of crude oil gathering and transportation systems are predicted.Considering the efficiency and unit consumption index of the crude oil gathering and transportation system,the energy efficiency evaluation system of the crude oil gathering and transportation system is established based on a game theory combined weighting method and TOPSIS evaluation method,and the subjective weight is determined by the triangular fuzzy analytic hierarchy process.The entropy weight method determines the objective weight,and the combined weight of game theory combines subjectivity with objectivity to comprehensively evaluate the comprehensive energy efficiency of crude oil gathering and transportation systems and their subsystems.Finally,the weak links in energy utilization are identified,and energy conservation and consumption reduction are improved.The above research provides technical support for the green,efficient and intelligent development of crude oil gathering and transportation systems.展开更多
When saving energy in a pneumatic system,the problem of energy losses is usually solved by reducing the air supply pressure.The power-matching method is applied to optimize the air-supply pressure of the pneumatic sys...When saving energy in a pneumatic system,the problem of energy losses is usually solved by reducing the air supply pressure.The power-matching method is applied to optimize the air-supply pressure of the pneumatic system,and the energy-saving effect is verified by experiments.First,the experimental platform of a pneumatic rotary actuator servo-control system is built,and the mechanism of the valve-controlled cylinder system is analyzed.Then,the output power characteristics and load characteristics of the system are derived,and their characteristic curves are drawn.The employed air compressor is considered as a constant-pressure source of a quantitative pump,and the power characteristic of the system is matched.The power source characteristic curve should envelope the output characteristic curve and load characteristic curve.The minimum gas supply pressure obtained by power matching represents the optimal gas supply pressure.The comparative experiments under two different gas supply pressure conditions show that the system under the optimal gas supply pressure can greatly reduce energy losses.展开更多
Copper-zinc alloy element for boiler energy saving was put in the intake of simulated boiler system to investigate the interaction and transfer of ions in water system both theoretically and experimentally. The foulin...Copper-zinc alloy element for boiler energy saving was put in the intake of simulated boiler system to investigate the interaction and transfer of ions in water system both theoretically and experimentally. The fouling was analyzed by scanning electron microscopy (SEM) and energy dispersive X-ray detector (EDX). The results show that the transfer of calcium and magnesium ions in heat-transfer-surface-water system is affected by zinc ions dissolved from the alloy because of primary battery reaction. Some calcium ions of calcium carbonate crystal are replaced by zinc ions, the growth of aragonite crystal nucleus is retarded, and the transition of calcium carbonate from aragonite to calcite is hampered.展开更多
To improve high-speed road feel and enhance energetic efficiency of hydraulic power steering(HPS) system in heavy-duty vehicles, an electromagnetic slip coupling(ESC) was applied to the steering system, which regulate...To improve high-speed road feel and enhance energetic efficiency of hydraulic power steering(HPS) system in heavy-duty vehicles, an electromagnetic slip coupling(ESC) was applied to the steering system, which regulated discharge flow of steering pump to realize variable assist characteristic as well as uniquely transfer on-demand power from engine to steering pump. The model of ESC was established and the dynamic characteristics of ESC were presented by the way of simulation and experiment. Upon the layout of the assist characteristics, output torque of ESC was derived. Based on the ESC model, the output torque characteristics of ESC were simulated under steering situation and straight driving situation, respectively. The consistency of simulated ESC output torque and the one deduced from assist characteristics verifies the correctness of the ESC dynamic model. To illustrate energy saving characteristics of ESC-HPS, energy consumption comparison of ESC-HPS and conventional HPS was carried out qualitatively and quantitatively. It follows that the energy consumption of ESC-HPS decreases by 50% compared with that of HPS.展开更多
Currently, many studies have been made for years on dimensions of pneumatic nozzle, which influence the flow characteristic of blowing system. For the purpose of outputting the same blowing force, the supply pressure ...Currently, many studies have been made for years on dimensions of pneumatic nozzle, which influence the flow characteristic of blowing system. For the purpose of outputting the same blowing force, the supply pressure could be reduced by decreasing the ratio of length to diameter of nozzle. The friction between high speed air and pipe wall would be reduced if the nozzle is designed to be converging shape comparing with straight shape. But the volume flow and pressure, discussed in these studies, do not describe energy loss of the blowing system directly. Pneumatic power is an innovative principle to estimate pneumatic system’s energy consumption directly. Based on the above principle, a pulse blowing method is put forward for saving energy. A flow experiment is carried out, in which the high speed air flows from the pulse blowing system and continuous blowing system respectively to a plate with grease on top. Supply pressure and the volume of air used for removing the grease are measured to calculate energy consumption. From the experiment result, the pulse blowing system performs to conserve energy comparing with the continuous blowing system. The frequency and duty ratio of pulse flow influence the blowing characteristic. The pulse blowing system performs to be the most efficient at the specified frequency and duty ratio. Then a pneumatic self-oscillated method based on air operated valve is put forward to generate pulse flow. A simulation is made about dynamic modeling the air operated valve and calculating the motion of the valve core and output pressure. The simulation result verifies the system to be able to generate pulse flow, and predicts the key parameters of the frequency and duty ratio measured by experiment well. Finally, on the basis of simplifying and solution of the pulse blowing system’s mathematic model, the relationship between system’s frequency duty ratio and the dimensions of components is simply described with four algebraic equations. The system could be designed with specified frequency and duty ratio according to the four equations. This study provides theoretical basis for designing energy-saving air blowing system.展开更多
Sour water contains ammonia,carbon dioxide,and hydrogen sulfides,producing from oil refining,coking,and coal gasification.To reduce the energy consumption in sour water stripping,a novel process is proposed which inte...Sour water contains ammonia,carbon dioxide,and hydrogen sulfides,producing from oil refining,coking,and coal gasification.To reduce the energy consumption in sour water stripping,a novel process is proposed which integrates with the bottom flashing mechanical vapor recompression heat pump(MVRHP)for treating such wastewater.Here,Aspen PlusTM as a powerful set of chemical process simulation software is utilized to investigate the economy and feasibility of the novel process.Comparison of the results of two process simulations,it can be seen that it is possible to reduce the total annual cost by nearly 45%to adopt the novel process,despite the capital investment increase 45%more than the conventional process.Thus,the provided conceptual design will play a guiding role in the industrialization of the process.展开更多
[Objective] The study aimed at evaluating the ability to save energy and reduce CO2 emission in China's cement industry. [Method] Based on long-term energy alternative planning system software (LEAP), "LEAP of Ch...[Objective] The study aimed at evaluating the ability to save energy and reduce CO2 emission in China's cement industry. [Method] Based on long-term energy alternative planning system software (LEAP), "LEAP of China's cement industry" model was established to simulate energy conservation and emission reduction in China's cement industry from 2010 to 2040 in different technologic situations. E ResultJ To save ener- gy and reduce CO2 emissions, new dry process kiln has priority over other technologies or measures, followed by equipment enlargement, mechani- cal shaft kiln, power generation system based on waste heat, as well as high-efficiency and energy-saving grinding technology, and new prepara- tion technology. If all the advanced technologies and measures are adopted, energy consumption and C02 emissions can be reduced by about 40.76% and 42.97% respectively. [ Condusion] LEAP of model is suitable for analyzing energy saving and emission reducing in China's cement industry and other industrial fields.展开更多
A problem of peak power in DC-electrified railway systems is mainly caused by train power demand during acceleration.If this power is reduced,substation peak power will be significantly decreased.This paper presents a...A problem of peak power in DC-electrified railway systems is mainly caused by train power demand during acceleration.If this power is reduced,substation peak power will be significantly decreased.This paper presents a study on optimal energy saving in DC-electrified railway with on-board energy storage system(OBESS) by using peak demand cutting strategy under different trip time controls.The proposed strategy uses OBESS to store recovered braking energy and find an appropriated time to deliver the stored energy back to the power network in such a way that peak power of every substations is reduced.Bangkok Mass Transit System(BTS)-Silom Line in Thailand is used to test and verify the proposed strategy.The results show that substation peak power is reduced by63.49% and net energy consumption is reduced by 15.56%using coasting and deceleration trip time control.展开更多
Aiming at the high fuel consumption and use-cost of truck-mounted concrete pump , an energy-saving matching strategy of pumping system is presented and the experimental study is conducted.Since pumping system occupies...Aiming at the high fuel consumption and use-cost of truck-mounted concrete pump , an energy-saving matching strategy of pumping system is presented and the experimental study is conducted.Since pumping system occupies most resources of engine , the matching strategy between engine and main pump is analyzed to meet the load demand and reduce the engine rational speed drop.The testing method is established to measure the fuel consumption of engine under various working conditions , and the experimental data are analyzed to find the law of the fuel consumption of engine.The system performance can be improved by adjusting the system input value.Finally , the energy-saving matching strategy is established to reduce the fuel consumption of truck for unit workload , which provides a new approach for the energy-saving of truck-mounted concrete pump.展开更多
Energy saving and emission reduction for railway systems should not only be studied from a technical perspective but should also be focused on management and economics. On the basis of relevant trainscheduling models ...Energy saving and emission reduction for railway systems should not only be studied from a technical perspective but should also be focused on management and economics. On the basis of relevant trainscheduling models for train operation management, in this paper we introduce an extended multi-objective trainscheduling optimization model considering locomotive assignment and segment emission constraints for energy saving. The objective of setting up this model is to reduce the energy and emission cost as well as total passenger- time. The decision variables include continuous variables such as train arrival and departure time, and binary vari- ables such as locomotive assignment and segment occu- pancy. The constraints are concerned with train movement, trip time, headway, and segment emission, etc. To obtain a non-dominated satisfactory solution on these objectives, a fuzzy multi-objective optimization algorithm is employed to solve the model. Finally, a numerical example is performed and used to compare the proposed model with the existing model. The results show that the proposed model can reduce the energy consumption, meet exhausts emission demands effectively by optimal locomotive assignment, and its solution methodology is effective.展开更多
To improve the power consumption of parallel applications at the runtime, modern processors provide frequency scaling and power limiting capabilities. In this work, a runtime strategy is proposed to maximize energy sa...To improve the power consumption of parallel applications at the runtime, modern processors provide frequency scaling and power limiting capabilities. In this work, a runtime strategy is proposed to maximize energy savings under a given performance degradation. Machine learning techniques were utilized to develop performance models which would provide accurate performance prediction with change in operating core-uncore frequency. Experiments, performed on a node (28 cores) of a modern computing platform showed significant energy savings of as much as 26% with performance degradation of as low as 5% under the proposed strategy compared with the execution in the unlimited power case.展开更多
An energy-saving control strategy based on predictive control for central air-conditioning systems is proposed in this paper. The cold load model is developed to describe the dynamic characteristics of temperature con...An energy-saving control strategy based on predictive control for central air-conditioning systems is proposed in this paper. The cold load model is developed to describe the dynamic characteristics of temperature control systems, and then parameters in the cold load model and in the central air-conditioning system model are estimated. Generalized predictive control (GPC) is used to establish an optimization model to minimize the consumption of energy and the control error of temperature. The simulated annealing (SA) algorithm, combined with quadratic programming, is adopted to solve the optimal problem. Contrasted with the simulation of traditional PID control, the results prove the effectiveness of this proposed strategy.展开更多
With the current,our country social economy rapid development,people's living standard and quality of life and therefore have got improved,at the same time,it is the concept of environmental protection and energy ...With the current,our country social economy rapid development,people's living standard and quality of life and therefore have got improved,at the same time,it is the concept of environmental protection and energy saving is also enhanced value,many fields in our country environmental protection and energysaving concept can be seen in the application,especially the application in building water supply and drainage design more widely,to protect the environment,to maximize the use of limited resources,how to reasonable use of water resources in building water supply and drainage construction,above is current the paper mainly discusses the problems in the construction field,this paper based on environmental protection and energy-saving concept,discusses its application in the building water supply and drainage design,for your reference.展开更多
Octane and p-xylene are common components in crude gasoline,so their separation process is very important in petroleum industry.The azeotrope and near azeotrope are often separated by extractive distillation in indust...Octane and p-xylene are common components in crude gasoline,so their separation process is very important in petroleum industry.The azeotrope and near azeotrope are often separated by extractive distillation in industry,which can realize the recovery and utilization of resources.In this work,the vapor–liquid equilibrium experiment was used to obtain the vapor–liquid equilibrium properties of the difficult separation system,and on this basis,the solvent extraction mechanism was studied.The mechanism of solvent separation plays a guiding role in selecting suitable solvents for industrial separation.The interaction energy,bond length and charge density distribution of p-xylene with solvent are calculated by quantum chemistry method.The quantum chemistry calculation results and experiment results showed that N-formylmorpholine is the best solvent among the alternative solvents in the work.This work provides an effective and complete solvent screening process from phase equilibrium experiments to quantum chemical calculation.An extractive distillation simulation process with N-formylmorpholine as solvent is designed to separate octane and p-xylene.In addition,the feasibility and effectiveness of the intensified vapor recompression assisted extraction distillation are also discussed.In the extractive distillation process,the vapor recompression-assisted extraction distillation process is globally optimal.Compared with basic process,the total annual cost can be reduced by 43.2%.This study provides theoretical guidance for extractive distillation separation technology and solvent selection.展开更多
The dispersing process of the blasted smoke in underground mines by ventilation is very important for the safety of personnel,and its energy consumption is also worthy of concern. In this study,the impact of supply ai...The dispersing process of the blasted smoke in underground mines by ventilation is very important for the safety of personnel,and its energy consumption is also worthy of concern. In this study,the impact of supply air flow rate on the decay process of harmful gases and fan energy,and the role of harmful gases buried by blasted pile in the smoke dispersing process is analyzed with three-dimensional numerical simulation. According to the results,air flow facilitates quick smoke dispersion and the gas emits from the blasted pile is only significant at the beginning of ventilation. It is thus recommended that large amount of air supply is taken to disperse the smoke quickly until the concentration of harmful gases reaches relevant standards,and reduce the amount of air in the remain time with frequency conversion technology to save energy. In the given study,12 m / s air flow rate is taken for dispersing smoke and 3 m / s air flow rate is taken for the waiting time. The energy consumption for ventilation is reduced by about 50%. In addition,due to the gases in the blasted pile remains very high concentration after the dispersing process,it is recommended to keep suitable amount of ventilation in the consequent process.展开更多
Since the raising of the cloud computing, the applications of web service have been extended rapidly. However, the data centers of cloud computing also cause the problem of power consumption and the resources usually ...Since the raising of the cloud computing, the applications of web service have been extended rapidly. However, the data centers of cloud computing also cause the problem of power consumption and the resources usually have not been used effectively. Decreasing the power consumption and enhancing resource utilization become main issues in cloud computing environment. In this paper, we propose a method, called MBFDP (modified best fit decreasing packing), to decrease power consumption and enhance resource utilization of cloud computing servers. From the results of experiments, the proposed solution can reduce power consumption effectively and enhance the utilization of resources of servers.展开更多
The very long tradition of the activated sludge treatment model within the water industry has demonstrated very versatile possibilities to adopt the operation mode for different enhancements. By looking into other tre...The very long tradition of the activated sludge treatment model within the water industry has demonstrated very versatile possibilities to adopt the operation mode for different enhancements. By looking into other treatment models within the activated sludge family it is possible to find alternatives for the operation. This paper concentrates on the possibilities to improve even small WWTP with respect to energy savings. The small plant in Northern Sweden, called Rosvik WWTP, is given as an example. Some important findings related to the intermittent aeration mode may be summarized as follows: 1) An energy savings for the operation of the small WWTP with respect to aeration needs that resulted in a decrease of the energy power supply by more than 35%, as compared with the previous operation based on continuous aeration;2) The up to date effluent levels with respect to the main pollutants have remained at very good levels in 2020, P-level averages 0.16 mg P/l versus consent level <</span><span> </span><span style="font-family:Verdana;">0.5 mg P/l;COD-level 40 versus <</span><span> </span><span><span style="font-family:Verdana;">70 mg/l and BOD</span><sub><span style="font-family:Verdana;">7</span></sub><span style="font-family:Verdana;"> 9 versus <</span></span><span> </span><span><span style="font-family:Verdana;">15 mg/l;3) Sometimes, also improved sludge settling characteristics have been observed, thus providing improved discharge figures;4) The potential to develop an enhanced biological phosphorus removal. There are however </span><span style="font-family:Verdana;">some needed conditions to accomplish these improvements: 1) Reliable</span><span style="font-family:Verdana;"> on-line probes for both oxygen control, SS-concentration control and optionally also for nitrogen control;2) A flexible automation system that allows the needed process modifications to take place;3) And finally, very important dedicated and competent plant operators, with the needed curiosity for operation improvements.展开更多
基金supported by the National Natural Science Foundation of China(No.71974129).
文摘In the hot summer&cold winter zone in China,intermittent heating space for rooms is widely used.However,in comparison with continuous space heating,the energy-saving performance of intermittent space heating has not been sufficiently investigated.This paper studied the factors influencing the energy performance of intermittent heating for the representativeoffice inhot summer&coldwinter zone.Basedon theheatbalancemethod,adynamic thermalmodel of the intermittent heating roomwas built and tested by experiments.And then,it analyzed the total space heating load,the amount of energy saving and energy saving ratio of the intermittent heating under different preheating hours,occupation hours,required roomtemperatures,air change rates,overall heat transfer coefficients(U-value)of windows and wall materials.If the adjacent rooms were not heated,for a typical room occupied about 10 h a day,the energy-saving ratio of intermittent heating was about 30%compared with continuous heating.But the preheating power was higher than two times of continuous heating.The results also indicated that the occupation hours had a significant effect on energy saving amount and ratio,it should be noted that the energy saving ratio by intermittent heating was much lower than the unoccupied period ratio.Relative to other factors,the heating temperatures,room air change rates and U-value of windows,and room envelope materials had little effect on energy efficiency.If the adjacent rooms were heated in the same manner as the roomin question,the energy-saving ratio of the total load of intermittent heating was heavily reduced to 8.46%.
文摘Denim is widely accepted among exported textile products due to its aesthetics, appearance, and fashion. Practitioners employed several physical or chemical treatments to improve denim qualities in denim finishing operations. So, several treatment processes, including enzymatic, bleaching, singeing, heat set, and ozone finish, are used, which made this processing more energy consumption and time-consuming. Therefore, it is significant to investigate how changing the chemicals and raw ingredients could improve the finishing process, which is environmentally and economically beneficial for sustainable production practices in the denim finishing process. This study’s research design comprises an experimental investigation in a denim plant in Bangladesh. Two different fabrics were chosen to analyze, determining the potential savings of finishing on the denim fabrics’ performance characteristics. By deducting singeing and heat-set processes, the researchers ran an experimental process by maintaining the same length of fabric. Then, the impacts of finishing process optimization on the mechanical, thermal, and comfort parameters of drape, stiffness, and tear strength were examined. The study’s findings demonstrated that this experiment increased productivity and reduced the finishing unit’s energy consumption without compromising the denim fabrics’ quality. This study significantly impacts environmental sustainability by preserving limited energy resources and manufacturing denim finishing processes.
基金This research was supported by the National Natural Science Foundation of China(Grant No.71971016).On behalf of all co-authors,the corresponding author states that there is no conflict of interest.
文摘Purpose–To address the problem that the current train operation mode that train selects one of several offline pre-generated control schemes before the departure and operates following the scheme after the departure,energy-saving performance of the whole metro system cannot be guaranteed.Design/methodology/approach–A cooperative train control framework is formulated to regulate a novel train operation mode.The classic train four-phase control strategy is improved for generating specific energy-efficient control schemes for each train.An improved brute force(BF)algorithm with a two-layer searching idea is designed to solve the optimisation model of energy-efficient train control schemes.Findings–Case studies on the actual metro line in Guangzhou,China verify the effectiveness of the proposed train control methods compared with four-phase control strategy under different kinds of train operation scenarios and calculation parameters.The verification on the computation efficiency as well as accuracy of the proposed algorithm indicates that it meets the requirement of online optimisation.Originality/value–Most existing studies optimised energy-efficient train timetable or train control strategies through an offline process,which has a defect in coping with the disturbance or delays effectively and promptly during real-time train operation.This paper studies an online optimisation of cooperative train control based on the rolling optimisation idea,where energy-efficient train operation can be realised once train running time is determined,thus mitigating the impact of unpredictable operation situations on the energy-saving performance of trains.
基金This work was financially supported by the National Natural Science Foundation of China(52074089 and 52104064)Natural Science Foundation of Heilongjiang Province of China(LH2019E019).
文摘As the main link of ground engineering,crude oil gathering and transportation systems require huge energy consumption and complex structures.It is necessary to establish an energy efficiency evaluation system for crude oil gathering and transportation systems and identify the energy efficiency gaps.In this paper,the energy efficiency evaluation system of the crude oil gathering and transportation system in an oilfield in western China is established.Combined with the big data analysis method,the GA-BP neural network is used to establish the energy efficiency index prediction model for crude oil gathering and transportation systems.The comprehensive energy consumption,gas consumption,power consumption,energy utilization rate,heat utilization rate,and power utilization rate of crude oil gathering and transportation systems are predicted.Considering the efficiency and unit consumption index of the crude oil gathering and transportation system,the energy efficiency evaluation system of the crude oil gathering and transportation system is established based on a game theory combined weighting method and TOPSIS evaluation method,and the subjective weight is determined by the triangular fuzzy analytic hierarchy process.The entropy weight method determines the objective weight,and the combined weight of game theory combines subjectivity with objectivity to comprehensively evaluate the comprehensive energy efficiency of crude oil gathering and transportation systems and their subsystems.Finally,the weak links in energy utilization are identified,and energy conservation and consumption reduction are improved.The above research provides technical support for the green,efficient and intelligent development of crude oil gathering and transportation systems.
基金Supported by Henan Province Science and Technology Key Project of China(Grant Nos.202102210081,202102210082)Fundamental Research Funds for Henan Province Colleges and Universities of China(Grant No.NSFRF140120)Doctor Foundation of Henan Polytechnic University(Grant No.B2012-101).
文摘When saving energy in a pneumatic system,the problem of energy losses is usually solved by reducing the air supply pressure.The power-matching method is applied to optimize the air-supply pressure of the pneumatic system,and the energy-saving effect is verified by experiments.First,the experimental platform of a pneumatic rotary actuator servo-control system is built,and the mechanism of the valve-controlled cylinder system is analyzed.Then,the output power characteristics and load characteristics of the system are derived,and their characteristic curves are drawn.The employed air compressor is considered as a constant-pressure source of a quantitative pump,and the power characteristic of the system is matched.The power source characteristic curve should envelope the output characteristic curve and load characteristic curve.The minimum gas supply pressure obtained by power matching represents the optimal gas supply pressure.The comparative experiments under two different gas supply pressure conditions show that the system under the optimal gas supply pressure can greatly reduce energy losses.
基金This work was financially supported by the Key Technologies R&D Program of Tianjin (No.06YFGZGX02400).
文摘Copper-zinc alloy element for boiler energy saving was put in the intake of simulated boiler system to investigate the interaction and transfer of ions in water system both theoretically and experimentally. The fouling was analyzed by scanning electron microscopy (SEM) and energy dispersive X-ray detector (EDX). The results show that the transfer of calcium and magnesium ions in heat-transfer-surface-water system is affected by zinc ions dissolved from the alloy because of primary battery reaction. Some calcium ions of calcium carbonate crystal are replaced by zinc ions, the growth of aragonite crystal nucleus is retarded, and the transition of calcium carbonate from aragonite to calcite is hampered.
基金Project(51275211)supported by the National Natural Science Foundation of ChinaProject(11KJA580001)supported by the Natural Science Fund for Colleges and Universities in Jiangsu Province,ChinaProject(CXZZ12_0665)supported by the Postgraduate Innovation Natural Science Foundation of Jiangsu Province,China
文摘To improve high-speed road feel and enhance energetic efficiency of hydraulic power steering(HPS) system in heavy-duty vehicles, an electromagnetic slip coupling(ESC) was applied to the steering system, which regulated discharge flow of steering pump to realize variable assist characteristic as well as uniquely transfer on-demand power from engine to steering pump. The model of ESC was established and the dynamic characteristics of ESC were presented by the way of simulation and experiment. Upon the layout of the assist characteristics, output torque of ESC was derived. Based on the ESC model, the output torque characteristics of ESC were simulated under steering situation and straight driving situation, respectively. The consistency of simulated ESC output torque and the one deduced from assist characteristics verifies the correctness of the ESC dynamic model. To illustrate energy saving characteristics of ESC-HPS, energy consumption comparison of ESC-HPS and conventional HPS was carried out qualitatively and quantitatively. It follows that the energy consumption of ESC-HPS decreases by 50% compared with that of HPS.
文摘Currently, many studies have been made for years on dimensions of pneumatic nozzle, which influence the flow characteristic of blowing system. For the purpose of outputting the same blowing force, the supply pressure could be reduced by decreasing the ratio of length to diameter of nozzle. The friction between high speed air and pipe wall would be reduced if the nozzle is designed to be converging shape comparing with straight shape. But the volume flow and pressure, discussed in these studies, do not describe energy loss of the blowing system directly. Pneumatic power is an innovative principle to estimate pneumatic system’s energy consumption directly. Based on the above principle, a pulse blowing method is put forward for saving energy. A flow experiment is carried out, in which the high speed air flows from the pulse blowing system and continuous blowing system respectively to a plate with grease on top. Supply pressure and the volume of air used for removing the grease are measured to calculate energy consumption. From the experiment result, the pulse blowing system performs to conserve energy comparing with the continuous blowing system. The frequency and duty ratio of pulse flow influence the blowing characteristic. The pulse blowing system performs to be the most efficient at the specified frequency and duty ratio. Then a pneumatic self-oscillated method based on air operated valve is put forward to generate pulse flow. A simulation is made about dynamic modeling the air operated valve and calculating the motion of the valve core and output pressure. The simulation result verifies the system to be able to generate pulse flow, and predicts the key parameters of the frequency and duty ratio measured by experiment well. Finally, on the basis of simplifying and solution of the pulse blowing system’s mathematic model, the relationship between system’s frequency duty ratio and the dimensions of components is simply described with four algebraic equations. The system could be designed with specified frequency and duty ratio according to the four equations. This study provides theoretical basis for designing energy-saving air blowing system.
基金the support provided by the National Key R&D Program of China(No.2017YFB0602804)the National Natural Science Foundation of China(No.21878164)。
文摘Sour water contains ammonia,carbon dioxide,and hydrogen sulfides,producing from oil refining,coking,and coal gasification.To reduce the energy consumption in sour water stripping,a novel process is proposed which integrates with the bottom flashing mechanical vapor recompression heat pump(MVRHP)for treating such wastewater.Here,Aspen PlusTM as a powerful set of chemical process simulation software is utilized to investigate the economy and feasibility of the novel process.Comparison of the results of two process simulations,it can be seen that it is possible to reduce the total annual cost by nearly 45%to adopt the novel process,despite the capital investment increase 45%more than the conventional process.Thus,the provided conceptual design will play a guiding role in the industrialization of the process.
基金Supported by Special Project for Developing National Major Scientific Instruments and Equipments (2011YQ060111)Scientific Research Project of Environmental Protection in Commonweal Industry(201009032)
文摘[Objective] The study aimed at evaluating the ability to save energy and reduce CO2 emission in China's cement industry. [Method] Based on long-term energy alternative planning system software (LEAP), "LEAP of China's cement industry" model was established to simulate energy conservation and emission reduction in China's cement industry from 2010 to 2040 in different technologic situations. E ResultJ To save ener- gy and reduce CO2 emissions, new dry process kiln has priority over other technologies or measures, followed by equipment enlargement, mechani- cal shaft kiln, power generation system based on waste heat, as well as high-efficiency and energy-saving grinding technology, and new prepara- tion technology. If all the advanced technologies and measures are adopted, energy consumption and C02 emissions can be reduced by about 40.76% and 42.97% respectively. [ Condusion] LEAP of model is suitable for analyzing energy saving and emission reducing in China's cement industry and other industrial fields.
文摘A problem of peak power in DC-electrified railway systems is mainly caused by train power demand during acceleration.If this power is reduced,substation peak power will be significantly decreased.This paper presents a study on optimal energy saving in DC-electrified railway with on-board energy storage system(OBESS) by using peak demand cutting strategy under different trip time controls.The proposed strategy uses OBESS to store recovered braking energy and find an appropriated time to deliver the stored energy back to the power network in such a way that peak power of every substations is reduced.Bangkok Mass Transit System(BTS)-Silom Line in Thailand is used to test and verify the proposed strategy.The results show that substation peak power is reduced by63.49% and net energy consumption is reduced by 15.56%using coasting and deceleration trip time control.
文摘Aiming at the high fuel consumption and use-cost of truck-mounted concrete pump , an energy-saving matching strategy of pumping system is presented and the experimental study is conducted.Since pumping system occupies most resources of engine , the matching strategy between engine and main pump is analyzed to meet the load demand and reduce the engine rational speed drop.The testing method is established to measure the fuel consumption of engine under various working conditions , and the experimental data are analyzed to find the law of the fuel consumption of engine.The system performance can be improved by adjusting the system input value.Finally , the energy-saving matching strategy is established to reduce the fuel consumption of truck for unit workload , which provides a new approach for the energy-saving of truck-mounted concrete pump.
基金supported by the National Natural Science Foundation of China (No. 71101007)the National High Technology Research and Development Program of China (No. 2011AA110502)State Key Laboratory of Rail Traffic Control and Safety of Beijing Jiaotong University Program (RCS2010ZZ001)
文摘Energy saving and emission reduction for railway systems should not only be studied from a technical perspective but should also be focused on management and economics. On the basis of relevant trainscheduling models for train operation management, in this paper we introduce an extended multi-objective trainscheduling optimization model considering locomotive assignment and segment emission constraints for energy saving. The objective of setting up this model is to reduce the energy and emission cost as well as total passenger- time. The decision variables include continuous variables such as train arrival and departure time, and binary vari- ables such as locomotive assignment and segment occu- pancy. The constraints are concerned with train movement, trip time, headway, and segment emission, etc. To obtain a non-dominated satisfactory solution on these objectives, a fuzzy multi-objective optimization algorithm is employed to solve the model. Finally, a numerical example is performed and used to compare the proposed model with the existing model. The results show that the proposed model can reduce the energy consumption, meet exhausts emission demands effectively by optimal locomotive assignment, and its solution methodology is effective.
文摘To improve the power consumption of parallel applications at the runtime, modern processors provide frequency scaling and power limiting capabilities. In this work, a runtime strategy is proposed to maximize energy savings under a given performance degradation. Machine learning techniques were utilized to develop performance models which would provide accurate performance prediction with change in operating core-uncore frequency. Experiments, performed on a node (28 cores) of a modern computing platform showed significant energy savings of as much as 26% with performance degradation of as low as 5% under the proposed strategy compared with the execution in the unlimited power case.
文摘An energy-saving control strategy based on predictive control for central air-conditioning systems is proposed in this paper. The cold load model is developed to describe the dynamic characteristics of temperature control systems, and then parameters in the cold load model and in the central air-conditioning system model are estimated. Generalized predictive control (GPC) is used to establish an optimization model to minimize the consumption of energy and the control error of temperature. The simulated annealing (SA) algorithm, combined with quadratic programming, is adopted to solve the optimal problem. Contrasted with the simulation of traditional PID control, the results prove the effectiveness of this proposed strategy.
文摘With the current,our country social economy rapid development,people's living standard and quality of life and therefore have got improved,at the same time,it is the concept of environmental protection and energy saving is also enhanced value,many fields in our country environmental protection and energysaving concept can be seen in the application,especially the application in building water supply and drainage design more widely,to protect the environment,to maximize the use of limited resources,how to reasonable use of water resources in building water supply and drainage construction,above is current the paper mainly discusses the problems in the construction field,this paper based on environmental protection and energy-saving concept,discusses its application in the building water supply and drainage design,for your reference.
基金This work is supported by the National Natural Science Foundation of China(No.21776145)National Natural Science Foundation of China(No.21676152).
文摘Octane and p-xylene are common components in crude gasoline,so their separation process is very important in petroleum industry.The azeotrope and near azeotrope are often separated by extractive distillation in industry,which can realize the recovery and utilization of resources.In this work,the vapor–liquid equilibrium experiment was used to obtain the vapor–liquid equilibrium properties of the difficult separation system,and on this basis,the solvent extraction mechanism was studied.The mechanism of solvent separation plays a guiding role in selecting suitable solvents for industrial separation.The interaction energy,bond length and charge density distribution of p-xylene with solvent are calculated by quantum chemistry method.The quantum chemistry calculation results and experiment results showed that N-formylmorpholine is the best solvent among the alternative solvents in the work.This work provides an effective and complete solvent screening process from phase equilibrium experiments to quantum chemical calculation.An extractive distillation simulation process with N-formylmorpholine as solvent is designed to separate octane and p-xylene.In addition,the feasibility and effectiveness of the intensified vapor recompression assisted extraction distillation are also discussed.In the extractive distillation process,the vapor recompression-assisted extraction distillation process is globally optimal.Compared with basic process,the total annual cost can be reduced by 43.2%.This study provides theoretical guidance for extractive distillation separation technology and solvent selection.
基金Sponsored by the 12th National Five-Year Science and Technology Support Program(Grant No.2012BAK09B07)
文摘The dispersing process of the blasted smoke in underground mines by ventilation is very important for the safety of personnel,and its energy consumption is also worthy of concern. In this study,the impact of supply air flow rate on the decay process of harmful gases and fan energy,and the role of harmful gases buried by blasted pile in the smoke dispersing process is analyzed with three-dimensional numerical simulation. According to the results,air flow facilitates quick smoke dispersion and the gas emits from the blasted pile is only significant at the beginning of ventilation. It is thus recommended that large amount of air supply is taken to disperse the smoke quickly until the concentration of harmful gases reaches relevant standards,and reduce the amount of air in the remain time with frequency conversion technology to save energy. In the given study,12 m / s air flow rate is taken for dispersing smoke and 3 m / s air flow rate is taken for the waiting time. The energy consumption for ventilation is reduced by about 50%. In addition,due to the gases in the blasted pile remains very high concentration after the dispersing process,it is recommended to keep suitable amount of ventilation in the consequent process.
文摘Since the raising of the cloud computing, the applications of web service have been extended rapidly. However, the data centers of cloud computing also cause the problem of power consumption and the resources usually have not been used effectively. Decreasing the power consumption and enhancing resource utilization become main issues in cloud computing environment. In this paper, we propose a method, called MBFDP (modified best fit decreasing packing), to decrease power consumption and enhance resource utilization of cloud computing servers. From the results of experiments, the proposed solution can reduce power consumption effectively and enhance the utilization of resources of servers.
文摘The very long tradition of the activated sludge treatment model within the water industry has demonstrated very versatile possibilities to adopt the operation mode for different enhancements. By looking into other treatment models within the activated sludge family it is possible to find alternatives for the operation. This paper concentrates on the possibilities to improve even small WWTP with respect to energy savings. The small plant in Northern Sweden, called Rosvik WWTP, is given as an example. Some important findings related to the intermittent aeration mode may be summarized as follows: 1) An energy savings for the operation of the small WWTP with respect to aeration needs that resulted in a decrease of the energy power supply by more than 35%, as compared with the previous operation based on continuous aeration;2) The up to date effluent levels with respect to the main pollutants have remained at very good levels in 2020, P-level averages 0.16 mg P/l versus consent level <</span><span> </span><span style="font-family:Verdana;">0.5 mg P/l;COD-level 40 versus <</span><span> </span><span><span style="font-family:Verdana;">70 mg/l and BOD</span><sub><span style="font-family:Verdana;">7</span></sub><span style="font-family:Verdana;"> 9 versus <</span></span><span> </span><span><span style="font-family:Verdana;">15 mg/l;3) Sometimes, also improved sludge settling characteristics have been observed, thus providing improved discharge figures;4) The potential to develop an enhanced biological phosphorus removal. There are however </span><span style="font-family:Verdana;">some needed conditions to accomplish these improvements: 1) Reliable</span><span style="font-family:Verdana;"> on-line probes for both oxygen control, SS-concentration control and optionally also for nitrogen control;2) A flexible automation system that allows the needed process modifications to take place;3) And finally, very important dedicated and competent plant operators, with the needed curiosity for operation improvements.