Energy Harvesting in the Wake of An Inverted C-Shaped Bluff Body

This paper proposes a novel wake-induced vibration(WIV)-based energy harvesting system consisting of two bluff bodies.An inverted C-shaped bluff body is stationary installed at the upstream position to generate an interference wake street,and a cylinder bluff body equipped with a transducer is elastically suspended at the downstream position to harness WIV energy.The hydrodynamics and energy harvesting(EH)performance of the proposed system are investigated via experimental studies.The reduced velocity(U*)ranging from 2 to 14(the corresponding Reynolds number ranging from 15100 to 106200)is considered in the present study.It is found that the wake generated by the inverted C-shaped bluff body significantly affects the EH performance.Enlarging the opening angle(α)of the C-shaped bluff body increases the vibration amplitude of the downstream cylinder,thereby increasing the harvested power.When the spacing(L)between two bluff bodies is two times the cylinder diameter(D),the wake-induced vibration(WIV)mode is observed,while the combined WIV and wake galloping(WG)mode occurs whenαis 150°,and L equals 3D or 4D.The average drag coefficient becomes negative when L is 2D,3D,or 4D.By carefully configuring a C-shaped bluff body,the wake generated by it can bring an augmenting effect on the vibration of the downstream EH cylinder.For example,the RMS power output of the proposed EH system reaches a maximum of 0.31 W at U*=8 and L=4D,which is 300%greater than that of its traditional counterpart.Furthermore,after a number of case stud-ies,it is identified that the proposed EH system can achieve the best performance whenαis 150°and L=2D.

Advances in Triboelectric Nanogenerators for Blue Energy Harvesting and Marine Environmental Monitoring

Blue energy,which includes rainfall,tidal current,wave,and water-flow energy,is a promising renewable resource,although its exploitation is limited by current technologies and thus remains low.This form of energy is mainly harvested by electromagnetic generators(EMGs),which generate electricity via Lorenz force-driven electron flows.Triboelectric nano genera tors(TENGs)and TENG networks exhibit superiority over EMGs in low-frequency and high-entropy energy harvesting as a new approach for blue energy harvesting.A TENG produces electrical outputs by adopting the mechanism of Maxwell’s displacement current.To date,a series of research efforts have been made to optimize the structure and performance of TENGs for effective blue energy harvesting and marine environmental applications.Despite the great progress that has been achieved in the use of TENGs in this context so far,continuous exploration is required in energy conversion,device durability,power management,and environmental applications.This review reports on advances in TENGs for blue energy harvesting and marine environmental monitoring.It introduces the theoretical foundations of TENGs and discusses advanced TENG prototypes for blue energy harvesting,including TENG structures that function in freestanding and contact-separation modes.Performance enhancement strategies for TENGs intended for blue energy harvesting are also summarized.Finally,marine environmental applications of TENGs based on blue energy harvesting are discussed.

Review of the Tuned Mass Damper Inerter(TMDI)in Energy Harvesting and Vibration Control:Designs,Analysis and Applications

Tuned mass damper inerter(TMDI)is a device that couples traditional tuned mass dampers(TMD)with an inertial device.The inertial device produces resistance proportional to the relative acceleration at its two ends through its“inertial”constant.Due to its unique mechanical properties,TMDI has received widespread attention and application in the past twenty years.As different configurations are required in different practical situations,TMDI is still active in the research on vibration control and energy harvesting in structures.This paper provides a comprehensive review of the research status of TMDI.This work first examines the generation and important vibration control characteristics of TMDI.Then,the energy harvesting performance of electromagnetic tuned mass damper inerter(EM-TMDI)is discussed.This work emphasizes the formation of a passive dynamic vibration absorber by coupling traditional TMD with inertial devices.This paper also summarizes the design and implementation of optimal vibration control and energy harvesting for TMDI.Furthermore,this paper details the applications of TMDI in the fields of bridges and building engineering.Finally,this paper summarizes the necessity of research on tuned mass-damper-inertia,the challenges faced currently,and future research directions,such as control of parameters in electromagnetic energy harvesting TMDI systems and low-cost TMDI.

Outage Analysis of Optimal UAV Cooperation with IRS via Energy Harvesting Enhancement Assisted Computational Offloading

The utilization of mobile edge computing(MEC)for unmanned aerial vehicle(UAV)communication presents a viable solution for achieving high reliability and low latency communication.This study explores the potential of employing intelligent reflective surfaces(IRS)andUAVs as relay nodes to efficiently offload user computing tasks to theMEC server system model.Specifically,the user node accesses the primary user spectrum,while adhering to the constraint of satisfying the primary user peak interference power.Furthermore,the UAV acquires energy without interrupting the primary user’s regular communication by employing two energy harvesting schemes,namely time switching(TS)and power splitting(PS).The selection of the optimal UAV is based on the maximization of the instantaneous signal-to-noise ratio.Subsequently,the analytical expression for the outage probability of the system in Rayleigh channels is derived and analyzed.The study investigates the impact of various system parameters,including the number of UAVs,peak interference power,TS,and PS factors,on the system’s outage performance through simulation.The proposed system is also compared to two conventional benchmark schemes:the optimal UAV link transmission and the IRS link transmission.The simulation results validate the theoretical derivation and demonstrate the superiority of the proposed scheme over the benchmark schemes.

Performance Analysis and Optimization of Energy Harvesting Modulation for Multi-User Integrated Data and Energy Transfer

Integrated data and energy transfer(IDET)enables the electromagnetic waves to transmit wireless energy at the same time of data delivery for lowpower devices.In this paper,an energy harvesting modulation(EHM)assisted multi-user IDET system is studied,where all the received signals at the users are exploited for energy harvesting without the degradation of wireless data transfer(WDT)performance.The joint IDET performance is then analysed theoretically by conceiving a practical time-dependent wireless channel.With the aid of the AO based algorithm,the average effective data rate among users are maximized by ensuring the BER and the wireless energy transfer(WET)performance.Simulation results validate and evaluate the IDET performance of the EHM assisted system,which also demonstrates that the optimal number of user clusters and IDET time slots should be allocated,in order to improve the WET and WDT performance.

Dynamic analysis of a novel multilink-spring mechanism for vibration isolation and energy harvesting

Due to technical limitations,existing vibration isolation and energy harvesting(VIEH)devices have poor performance at low frequency.This paper proposes a new multilink-spring mechanism(MLSM)that can be used to solve this problem.The VIEH performance of the MLSM under harmonic excitation and Gaussian white noise was analyzed.It was found that the MLSM has good vibration isolation performance for low-frequency isolation and the frequency band can be widened by adjusting parameters to achieve a higher energy harvesting power.By comparison with two special cases,the results show that the MLSM is basically the same as the other two oscillators in terms of vibration isolation but has better energy harvesting performance under multistable characteristics.The MLSM is expected to reduce the impact of vibration on high-precision sensitive equipment in some special sites such as subways and mines,and at the same time supply power to structural health monitoring devices.

Integrated device for multiscale series vibration reduction and energy harvesting

A multi-degree-of-freedom device is proposed,which can achieve efficient vibration reduction as the main objective and energy harvesting as the secondary purpose.The device comprises a multiscale nonlinear vibration absorber(NVA)and piezoelectric components.Energy conversion and energy measurement methods are used to evaluate the device performance from multiple perspectives.Research has shown that this device can efficiently transfer transient energy from the main structure and convert a portion of transient energy into electrical energy.Main resonance and higher-order resonance are the main reasons for efficient energy transfer.The device can maintain high vibration reduction performance even when the excitation amplitude changes over a large range.Compared with the single structures with and without precompression,the multiscale NVA-piezoelectric device offers significant vibration reduction advantages.In addition,there are significant differences in the parameter settings of the two substructures for vibration reduction and energy harvesting.

Efficient thermal management and all-season energy harvesting using adaptive radiative cooling and a thermoelectric power generator

Passive daytime radiative cooling(PDRC) is useful for thermal management because it allows an object to emit terrestrial heat into space without the use of additional energy.To produce sub-ambient temperatures under direct sunlight,PDRC materials are designed to reduce their absorption of solar energy and to enhance their long-wavelength infrared(LWIR) emissivity.In recent years,many photonic structures and polymer composites have been studied to improve the cooling system of buildings.However,in cold weather(i.e. during winter in cold climates),buildings need to be kept warm rather than cooled due to heat loss.To overcome this limitation,temperature-responsive radiative cooling is a promising alternative.In the present study,adaptive radiative cooling(ARC) film fabricated from a polydimethylsiloxane/hollow SiO_(2) microsphere/thermochromic pigment composite was investigated.We found that the ARC film absorbed solar radiation under cold conditions while exhibiting radiative cooling at ambient temperatures above 40℃.Thus,in outdoor experiments,the ARC film achieved sub-ambient temperatures and had a theoretical cooling power of 63.2 W/m~2 in hot weather.We also demonstrated that radiative cooling with an energy harvesting system could be used to improve the energy management of buildings,with the thermoelectric module continuously generating output power using the ARC film.Therefore,we believe that our proposed ARC film can be employed for efficient thermal management of buildings and all-season energy harvesting in the near future.

Green Fabrication of Freestanding Piezoceramic Films for Energy Harvesting and Virus Detection

Most electronics such as sensors,actuators and energy harvesters need piezoceramic films to interconvert mechanical and electrical energy.Transferring the ceramic films from their growth substrates for assembling electronic devices commonly requires chemical or physical etching,which comes at the sacrifice of the substrate materials,film cracks,and environmental contamination.Here,we introduce a van der Waals stripping method to fabricate large-area and freestanding piezoceramic thin films in a simple,green,and cost-effective manner.The introduction of the quasi van der Waals epitaxial platinum layer enables the capillary force of water to drive the separation process of the film and substrate interface.The fabricated lead-free film,Ba_(0.85)Ca_(0.15)Zr_(0.1)Ti_(0.9)O_(3)(BCZT),shows a high piezoelectric coefficient d_(33)=209±10 pm V−1 and outstanding flexibility of maximum strain 2%.The freestanding feature enables a wide application scenario,including micro energy harvesting,and covid-19 spike protein detection.We further conduct a life cycle analysis and quantify the low energy consumption and low pollution of the water-based stripping film method.

Dynamic responses of an energy harvesting system based on piezoelectric and electromagnetic mechanisms under colored noise

Because of the increasing demand for electrical energy,vibration energy harvesters(VEHs)that convert vibratory energy into electrical energy are a promising technology.In order to improve the efficiency of harvesting energy from environmental vibration,here we investigate a hybrid VEH.Unlike previous studies,this article analyzes the stochastic responses of the hybrid piezoelectric and electromagnetic energy harvesting system with viscoelastic material under narrow-band(colored)noise.Firstly,a mass-spring-damping system model coupled with piezoelectric and electromagnetic circuits under fundamental acceleration excitation is established,and analytical solutions to the dimensionless equations are derived.Then,the formula of the amplitude-frequency responses in the deterministic case and the first-order and secondorder steady-state moments of the amplitude in the stochastic case are obtained by using the multi-scales method.The amplitude-frequency analytical solutions are in good agreement with the numerical solutions obtained by the Monte Carlo method.Furthermore,the stochastic bifurcation diagram is plotted for the first-order steady-state moment of the amplitude with respect to the detuning frequency and viscoelastic parameter.Eventually,the influence of system parameters on mean-square electric voltage,mean-square electric current and mean output power is discussed.Results show that the electromechanical coupling coefficients,random excitation and viscoelastic parameter have a positive effect on the output power of the system.

Enhanced vibration suppression and energy harvesting in fluid-conveying pipes

A novel vibration absorber is designed to suppress vibrations in fluidconveying pipes subject to varying fluid speeds.The proposed absorber combines the fundamental principles of nonlinear energy sinks(NESs)and nonlinear energy harvesters(NEHs).The governing equation is derived,and a second-order discrete system is used to assess the performance of the developed device.The results demonstrate that the proposed absorber achieves significantly enhanced energy dissipation efficiency,reaching up to 95%,over a wider frequency range.Additionally,it successfully harvests additional electric energy.This research establishes a promising avenue for the development of new nonlinear devices aimed at suppressing fluid-conveying pipe vibrations across a broad frequency spectrum.

Metaheuristic Secure Clustering Scheme for Energy Harvesting Wireless Sensor Networks

Recently,energy harvesting wireless sensor networks(EHWSN)have increased significant attention among research communities.By harvesting energy from the neighboring environment,the sensors in EHWSN resolve the energy constraint problem and offers lengthened network lifetime.Clustering is one of the proficient ways for accomplishing even improved lifetime in EHWSN.The clustering process intends to appropriately elect the cluster heads(CHs)and construct clusters.Though several models are available in the literature,it is still needed to accomplish energy efficiency and security in EHWSN.In this view,this study develops a novel Chaotic Rider Optimization Based Clustering Protocol for Secure Energy Harvesting Wireless Sensor Networks(CROC-SEHWSN)model.The presented CROC-SEHWSN model aims to accomplish energy efficiency by clustering the node in EHWSN.The CROC-SEHWSN model is based on the integration of chaotic concepts with traditional rider optimization(RO)algorithm.Besides,the CROC-SEHWSN model derives a fitness function(FF)involving seven distinct parameters connected to WSN.To accomplish security,trust factor and link quality metrics are considered in the FF.The design of RO algorithm for secure clustering process shows the novelty of the work.In order to demonstrate the enhanced performance of the CROC-SEHWSN approach,a wide range of simulations are carried out and the outcomes are inspected in distinct aspects.The experimental outcome demonstrated the superior performance of the CROC-SEHWSN technique on the recent approaches with maximum network lifetime of 387.40 and 393.30 s under two scenarios.

Solar Energy Harvesting Using a Timer-Based Relay Selection

In this paper,the throughput and delay of cooperative communications are derived when solar energy is used and relay node is selected using a timer.The source and relays harvest energy from sun using a photo voltaic system.The harvested power is used by the source to transmit data to the relays.Then,a selected relay amplifies the signal to the destination.Opportunistic,partial and reactive relay selection are used.The relay transmits when its timer elapses.The timer is set to a value proportional to the inverse of its Signal to Noise Ratio(SNR).Therefore,the relay with largest SNR will transmit first and its signal will be detected by the other relays that will remain idle to avoid collisions.Harvesting duration is optimized to maximize the throughput.Packet’s waiting time and total delay are also computed.We also derive the statistics of SNR when solar energy is used.The harvested power from sun is proportional to the sum of a deterministic radiation intensity and a random attenuation due to weather effects and clouds occlusion.The fixed radiation intensity depends on season,month and time t in hour.The throughput of cooperative communications with energy harvesting from sun was not yet studied.

Comparison of Energy Harvesting Systems for Wireless Sensor Networks

Wireless sensor networks (WSNs) offer an attractive solution to many environmental,security,and process monitoring problems.However,one barrier to their fuller adoption is the need to supply electrical power over extended periods of time without the need for dedicated wiring.Energy harvesting provides a potential solution to this problem in many applications.This paper reviews the characteristics and energy requirements of typical sensor network nodes,assesses a range of potential ambient energy sources,and outlines the characteristics of a wide range of energy conversion devices.It then proposes a method to compare these diverse sources and conversion mechanisms in terms of their normalised power density.

Modeling and analysis of piezoelectric beam with periodically variable cross-sections for vibration energy harvesting

A bimorph piezoelectric beam with periodically variable cross-sections is used for the vibration energy harvesting. The effects of two geometrical parameters on the first band gap of this periodic beam are investigated by the generalized differential quadrature rule （GDQR） method. The GDQR method is also used to calculate the forced vibration response of the beam and voltage of each piezoelectric layer when the beam is subject to a sinusoidal base excitation. Results obtained from the analytical method are compared with those obtained from the finite element simulation with ANSYS, and good agreement is found. The voltage output of this periodic beam over its first band gap is calculated and compared with the voltage output of the uniform piezoelectric beam. It is concluded that this periodic beam has three advantages over the uniform piezoelectric beam, i.e., generating more voltage outputs over a wide frequency range, absorbing vibration, and being less weight.

Broadband energy harvesting via magnetic coupling between two movable magnets

Harvesting energy from ambient mechanical vibrations by the piezoelectric effect has been proposed for powering microelectromechanical systems and replacing batteries that have a finite life span. A conventional piezoelectric energy harvester （PEH） is usually designed as a linear resonator, and suffers from a narrow operating bandwidth. To achieve broadband energy harvesting, in this paper we introduce a concept and describe the realization of a novel nonlinear PEH. The proposed PEH consists of a primary piezoelectric cantilever beam coupled to an auxiliary piezoelectric cantilever beam through two movable magnets. For predicting the nonlinear response from the proposed PEH, lumped parameter models are established for the two beams. Both simulation and experiment reveal that for the primary beam, the introduction of magnetic coupling can expand the operating bandwidth as well as improve the output voltage. For the auxiliary beam, the magnitude of the output voltage is slightly reduced, but additional output is observed at off-resonance frequencies. Therefore, broadband energy harvesting can be obtained from both the primary beam and the auxiliary beam.

Hierarchical Honeycomb-Structured Electret/Triboelectric Nanogenerator for Biomechanical and Morphing Wing Energy Harvesting

Flexible,compact,lightweight and sustainable power sources are indispensable for modern wearable and personal electronics and small-unmanned aerial vehicles(UAVs).Hierarchical honeycomb has the unique merits of compact mesostructures,excellent energy absorption properties and considerable weight to strength ratios.Herein,a honeycomb-inspired triboelectric nanogenerator(h-TENG)is proposed for biomechanical and UAV morphing wing energy harvesting based on contact triboelectrification wavy surface of cellular honeycomb structure.The wavy surface comprises a multilayered thin film structure(combining polyethylene terephthalate,silver nanowires and fluorinated ethylene propylene)fabricated through high-temperature thermoplastic molding and wafer-level bonding process.With superior synchronization of large amounts of energy generation units with honeycomb cells,the manufactured h-TENG prototype produces the maximum instantaneous open-circuit voltage,short-circuit current and output power of 1207 V,68.5μA and 12.4 mW,respectively,corresponding to a remarkable peak power density of 0.275 mW cm^(−3)(or 2.48 mW g^(−1))under hand pressing excitations.Attributed to the excellent elastic property of self-rebounding honeycomb structure,the flexible and transparent h-TENG can be easily pressed,bent and integrated into shoes for real-time insole plantar pressure mapping.The lightweight and compact h-TENG is further installed into a morphing wing of small UAVs for efficiently converting the flapping energy of ailerons into electricity for the first time.This research demonstrates this new conceptualizing single h-TENG device’s versatility and viability for broad-range real-world application scenarios.

Flexible Ag Microparticle/MXene-Based Film for Energy Harvesting

Ultra-thin flexible films have attracted wide attention because of their excellent ductility and potential versatility.In particular,the energy-harvesting films(EHFs)have become a research hotspot because of the indispensability of power source in various devices.However,the design and fabrication of such films that can capture or transform di erent types of energy from environments for multiple usages remains a challenge.Herein,the multifunctional flexible EHFs with e ective electro-/photo-thermal abilities are proposed by successive spraying Ag microparticles and MXene suspension between on waterborne polyurethane films,supplemented by a hot-pressing.The optimal coherent film exhibits a high electrical conductivity(1.17×10^(4)S m^(-1)),excellent Joule heating performance(121.3℃)at 2 V,and outstanding photo-thermal performance(66.2℃ within 70 s under 100 mW cm^(-1)).In addition,the EHFs-based single-electrode triboelectric nanogenerators(TENG)give short-circuit transferred charge of 38.9 nC,open circuit voltage of 114.7 V,and short circuit current of 0.82μA.More interestingly,the output voltage of TENG can be further increased via constructing the double triboelectrification layers.The comprehensive ability for harvesting various energies of the EHFs promises their potential to satisfy the corresponding requirements.

Performance enhancement of wing-based piezoaeroelastic energy harvesting through freeplay nonlinearity

We investigate experimentally how controlled freeplay nonlinearity affects harvesting energy from a wing-based piezoaeroelastic energy harvesting system. This system consisits of a rigid airfoil which is supported by a nonlinear torsional spring （freeplay） in the pitch degree of freedom and a linear fiexural spring in the plunge degree of freedom. By attaching a piezoelectric material （PSI-5A4E） to the plunge degree of freedom, we can convert aeroelastic vibrations to electrical energy. The focus of this study is placed on the effects of the freeplay nonlinearity gap on the behavior of the harvester in terms of cut-in speed and level of harvested power. Although the freeplay nonlinearity may result in subcritical Hopf bifurcations （catastrophic for real aircrafts）, harvesting energy at low wind speeds is beneficial for designing piezoaeroelastic systems. It is demonstrated that increasing the freeplay nonlinearity gap can decrease the cut-in speed through a subcritical instability and gives the possibility to harvest energy at low wind speeds. The results also demonstrate that an optimum value of the load resistance exists, at which the level of the harvested power is maximized.

Energy harvesting by two magnetopiezoelastic oscillators with mistuning

We examine an energy harvesting system of two magnetopiezoelastic oscillators coupled by electric circuit and driven by harmonic excitation. We focus on the effects of synchronization and escape from a single potential well. In the system with relative mistuning in the stiffness of the har- vesting oscillators, we show the dependence of the voltage output for different excitation frequencies.